Construction of Kitchen Shed cum Store Building in Government High School in South Sirukalathur at Sirukalathur Panchayat Kundrathur Panchayat Union

Earth work excavation for foundation in all soils and sub-soils to full depth as may be directed except in In hard stiff clay, stiff blackcotton soil, hard red earth, shale murams, gravel stony earth and earth muds with 50%(fifty percent) fair size boulders and hard gravely soils(SS20B)

Supplying and filling in foundation and basement with FILLING SAND in layers not more 15 cm thick well rammed watered and compacted .complete complying to standard specification

Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,

Cement Concrete 1:4:8 (one cement , five sand, and Ten hard broken stone) Using 40 mm gauge Hand Broken Granite stone jelly for Foundation including watering whenever necessary and laid in layers not more than 15 cm thick.compacting etc., complete

Reinforced Cement Concrete 1:1.5:3 (one cement , two sand, and four hard broken stone) using 20 mm , gauge machine broken hard granite stones jelly for RCC items of works excluding cost of reinforcement and fabricating Charges and centering and shuttering charges complete Upto base

Reinforced Cement Concrete 1:1.5:3 (one cement , two sand, and four hard broken stone) using 20 mm , gauge machine broken hard granite stones jelly for RCC items of works excluding cost of reinforcement and fabricating Charges and centering and shuttering charges complete - above Base

Brick work in Cement Mortar 1:5 (One cement and five sand) using Country Bricks ground moulded of size 23 x11 x7cm. For the following including curing etc., complete complying with standard specification. Upto base

Brick work in Cement Mortar 1:5 (One cement and five sand) using Country Bricks ground moulded of size 23 x11 x7cm. For the following including curing etc., complete complying with standard specification. Above base

Supplying and erecting centering of sides and soffits including supports and strutting up to 3.29 m height for plane surfaces in all floors with all cross bracing using mild steel sheets of size 90 cm X 60 cm and 10 gauge stiffened welded with mild steel angels of size 25 mm X 25mm X 3 mm etc. complete complying with standard specification Upto base

Supplying and erecting centering of sides and soffits including supports and strutting up to 3.29 m height for plane surfaces in all floors with all cross bracing using mild steel sheets of size 90 cm X 60 cm and 10 gauge stiffened welded with mild steel angels of size 25 mm X 25mm X 3 mm etc. complete complying with standard specification Above base

Supplying, fabricating and placing in position mild steel or ribbed tor steel and all reinforced cement concrete works as per the design given including cost of steel and binding wire in all floors etc. complete complying with standard specification

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone M.Sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) Using anti-skid tiles

Plastering with CEMENT MORTAR 1:5 (one cement and five sand)12 mm. thick in all floor including curing etc.Complete complying with standard specification.

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [ The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete]. The Putty shoule be got approved by the Executive Engineer before use on work.

Painting two coats with ready mixed plastic emulsion paint of Ist class etc., with best approved best quality of synthetic emulsion paint of approved colour over the existing priming coat etc., complete

Painting two coats with ready mixed OBD paint of Ist class etc., with best approved best quality of Distemeper paint of approved colour over the existing priming coat etc., complete

Painting TWO coats of new iron works such as steel doors, windows,ventilators, window bars, balustrades etc., with best approved first quality of synthetic enamel paint

Fabrication and supply of Mild Steel Door Of size 1.00mx2.10m with double leaves,outer frame made of 35x35x5 mm equal MSL angle and shutter frame made of 25x25x5 mm equal MS angle for horizantal and vertical members and the shutter frame strenghtened by stiffness of 2 Nos Horizantal amd 3 nos diagonal for each shutter using MS flat of size 20x5 mm fully covered with 18 gauge plain MS full sheet welded with shutter frame neatly and also fixing by welding 6 nos holdfasts , 2 nos of wind appliances , 3 nos of tower bolts, 1 no aldrop , 3 nos of handles, fixing shutter with 6 nos of hinges

Fabrication and supply of Mild Steel window od size 0.9m x 1.20m with double leaves,outer frame made of 35x35x5 mm equal MSL angle mullion section made of 35x35x5 mm T section & shutter frame made of 25x25x5 mm equal MS angle for horizantal and vertical members and the shutter frame strenghtened by stiffness of 1 No Horizantal for each shutter using MS flat of size 20x5 mm fully covered with 18 gauge plain MS full sheet welded with shutter frame neatly and also fixing by welding 6 nos holdfasts , 2 nos of wind appliances , 3 nos of tower bolts, 1 no aldrop , 3 nos of handles, fixing shutter with 6 nos of hinges