SPECIAL REPAIRS TO FILTRATION PLANT BLDG NOS P 49 AND P 226 AND JACK WELL BLDG NOS P-95 P 247 AND T 21 AT GIRINAGAR PUNE 25

Amount

B/R PORTION Complete removal of entire existing water proofing treatment in any position including tarfelt, Plaster, lean concrete, gravels etc. and removing the debries out side MD land all as specified and directed.

M&L for cement concrete type B1,1:2:4 (using 20mm graded stone aggregate) as in kerb or mud stop, slightly rounded or champhered on edges complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:4 over concrete surfaces finished even and smooth with using extra cement, mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. Note: Water Proofing compound shall be measured and paid for seprately as "Supply Only"

M & L for APP based polymeric membrane minimum weight 3 Kgs/Sqm and minimum 3 mm thick reinforced with polyster non-woven fabric ( wt not less than 150 gms/sqm laid over primed surface with bituminous primer conforming to IS- 3384 @ 0.3 litre/sqm and finishing with preventive coat with aluminium paint @ 100ml/sqm all as directed and specified including cutting chases to wall and making good in CM 1:3 as in vertical surface complete all as specified and directed.

Supply only Water Proofing Compund of approved make.

Dismantling asbestos cement, CGI sheets (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Taking down chowkats or frames of wooden or steel exc 1.5 sqm & n.exc. 4 Sqm with Shutters (without taking off shutters from the frames) complete all as specified and directed.

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, supplied and fixed size 105X60mm complete all as specified and directed.

M&L for PCC 1:3:6 type C-0 (using 12.5mm graded aggregate) as in filling steel frames etc. incl necessary form work complete all as specified and directed

M&L for 35mm thick Flush shutters with lipping all around of solid core construction with block board core and ply wood face panels commercial type on both side complete all as specified and directed.

S&F 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

M&L for 150mm long door stopper of aluminium alloy body fixed to door complete all as specified and directed.

S&F 150mm long aluminium handles, cast type anodised complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

M&L for two coat of synthetic enamel paint over a coat of pink primer including preparation of new/old painted wood surfaces complete all as specified and directed

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off complete all as specified and directed.

M&L for Rendering 15mm thick on brick, stone or concrete surfaces in cement mortar 1:4 finished surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for Rendering 15 mm thick on brick, stone surfaces in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 5mm thick rendering in CM 1:3 on concrete surfaces in ceiling complete all as specified and directed.

M&L for preparation of surfaces and applying 2mm thick wall care putty in two layers on walls/concrete over new or old plaster surfaces internally complete all as specified and directed.

M&L for preparation of surfaces and applying two coats of oil bound distemper over a coat of primer on New surfaces of wall complete all as specified and directed.

M&L for preparation of surfaces and applying two coats of oil bound distemper over a coat of primer on Old surfaces of wall complete all as specified and directed.

M&L for preparation of surfaces and applying three coats of white wash on New surfaces of wall complete all as specified and directed.

M&L for preparation of surfaces and applying three coats of white wash on Old surfaces of wall complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43litre/10sqm over and including priming coat of exterior primer applied @ 0.90litre/10Sqm over new surfaces of wall including necessary scaffolding required for painting work, safety measures etc complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings etc. with ends of bars shouldered or riveted or gorged into spikes framed guard bars barred to windows, iron door,ladders framed balusters, walk ways, railing, frame work for water tank and similar work conforming to Fe-290 Gde E-165 complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in floor levelling course and in similar situations 25mm thick complete all as specified and directed.

M&L for Non Skid Ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11Sqm but not exceeding 0.18Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surfaces 300 x 450 x 7mm thick as in dado/skirting etc. and joineted neat in cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in CM 1:4 including the cost of 6mm thick Recron 3s Polypropylene fibre @ 0.25Kg/Bag of cement for rendering complete all as directed.

M&L for Glass mosaic coloured tiles 5-6mm thick of size exc 0.11 Sqm but n exc 0.18 Sqm (chequed finish size 25mm x 25mm / 20mm x 20mm) laid in under water structure floor/wall surfaces with and including tile admixture weber manufacture by Saint Gobain as per manufactures instructions over and including 15mm thick screed bed/rendering in CM 1:4 complete all as specified and directed.

M & L for granite 18mm thick black/red colour (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including one side rounded and polished complete all as specified and directed.

M&L for 20mm thick machine cut kota stone slab flooring as in stair case tread, landings laid over and including 20mm thick screed base in CM 1:6 and jointed in with grey cement to match the shade of the slab including rubbing, cutting and polishing complete and horizontaly 3 Nos anti skid cutting to tread including preparation of old surfaces complete all as directed.

M&L for 20mm thick machine cut kota stone slab as in riser of steps, skerting, dado and pillar laid over and including 15mm thick rendering in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab inlcuding rubbing, cutting and polishing complete all as directed.

M&L for 20mm to 22mm thick Rubber sheet with fabric backing or insert and plain coloured or marbled topping, matt or glossy laid in floors with aprroved adhesive including preparation of surface to receive rubber sheet complete all as specified and directed.

Dismantling stone slab of any description or thickness in floors, approns etc complete all as specified and directed.

M&L for 30mm to 40mm thick rough dressed sahabad stone slab flooring bedded and jointed in cement mortar (1:6) and pointed in CM (1:3) complete all as specified and directed.

All as per Item Ser No 37.00 here-in-before but except sahabad stone.

Taking down chowkats or frames of wooden or steel window/ventilator not exc 1.5 sqm with Shutters (without taking off shutters from the frames) complete all as specified and directed.

S&F three track sliding window with 4mm thick tinted glass in two shutter and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18mm width aperture for mosquito proofing including good quality bearing handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed by Engr-in-Charge. Series of aluminium section as per Jindal is (a) Bottom frame - 20620 (b) Top frame & vertical - 20621 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724 (e) Shutter top & Bottom - 20844 (f) Glazing clips - 19352.

S&F anodised powder coated (thickness of powder coating not less than 50micron) aluminim window and ventilator shutters, with lauvers type with aluminium up and down track, aluminium section weight not less than 0.55kg/mtr including necessary joining cleats, glazing clips, rubber packing, screws etc. complete all as specified & directed.

M&L for 4mm thick figured glass, pin head type and glazing with not exc.0.5Sqm in each pane to aluminium frame work for ventilators complete all as specified and directed.

M& L for Silicon sealant for sealing of existing window aluminium frame with penetration depth 10 mm and 10 mm wide using sealant gun finished in triangular shape complete all as specified and as directed.

S&F in repair vitreous china orrisa pan squatting pattern 580x440mm with integral foot rests including P or S trap, including PVC low level flushing cistern 10 ltr capacity complete all as specified and directed.

S&F Wash hand basin, vitrous china, coloured flat back of size 550 x 400mm including cutting for and pining in ends of brackets or erecting stand including brass waste coupling, waste pipe, 15mm dia bore pillar taps, cast copper alloy chromium plated fancy type fixed complete all as specified and directed.

S&F in repairs Long body Bib taps fancy type chromium plated for 15mm bore pipe, screwed for CPVC/Iron pipes or for brass ferrule all complete as specified and as directed.

S&F in repair fancy type, chromium plated angular stop cock fixed with wall flange for 15mm bore of pipe fixed to CPVC/GI pipe complete all as specified and as directed.

S&F in repair 125mm chromium plated shower roses with or without swivel joints, any size including fixing to CPVC/Steel pipe complete all as specified and directed.

S&F stainless steel grating doom 125mm dia complete all as specified.

S&F brass chromium plated tubular towel rail 20mm dia and each towel rail 60cm long including CP brackets both sides for each towel rail ccomplete all as specified and directed.

S&F for 20mm dia CPVC pipes SDR 11 including all Brass CPVC fittings for 20mm bore pipe on walls/ceiling or laying in floors complete. Including taking up or down steel tubing and connections or removal to store all as specified & directed.

S&F for 16mm dia CPVC pipes SDR 11 including all Brass CPVC fittings for 16mm bore pipe on walls/ceiling or laying in floors complete. Including taking up or down steel tubing and connections or removal to store all as specified & directed.

S&F 20mm dia CPVC Ball valve ccomplete all as specified and directed.

M&L for cutting chases, pinning in stone, concrete block walls making good to facings where required and pointing in cement mortar 1:3 to concealed water tubing and making good complete all as directed & directed.

S&F 500 ltrs capacity, Rotational moulded polythylene water storage tank tripple layer (cylindrical vertical with closed top) hoisted and in position including ball brass valve 25mm high pressure with polythene float and fly nut complete including dismantling existing water tank and removing to store all as specified and directed.

S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall, floor of size 110mm bore complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall, floor of size 75mm bore complete all as specified and directed.

S&F PVC (SWR) junction, (Single Tee) with excess door equal or unequal 110mm bore complete all as specified and directed.

S&F PVC (SWR) junction, (Single Tee) with excess door equal or unequal 75mm bore complete all as specified and directed.

S&F PVC (SWR) bends of any radius 110mm bore complete all as specified and directed.

S&F PVC (SWR) bends of any radius 75mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) gully traps 125/100mm setting and jointed in cement solvent complete all as specified and directed.

Demolition of cement concrete in floors and pavings n. exc. 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for Hardcore of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8 type B1 (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for coloured glossy finish chequered cement concrete tiles 30cm x 30cm x 25mm thick with grey cement and no pigment, set and jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 100mm thick cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) Using dewatering trimix method finishing cement concrete surface even and smooth without using extra cement including construction joint at each 2mtr interval. The Joint shall be filled with sealing compound Grade 'A' (to full depth) complete all as specified and directed.

M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

S&F Pre-painted coloured galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/Chajja/cladding to wall, height upto 10mtr from floor level fixed with self tapping screws/'J' hook as directed by Engr-in-Charge and colour of sheet to be prior approval from GE.

S&F Pre-painted coloured galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/ridge/Chajja/cladding to wall, fixed with self tapping screws/'J' hook as directed by Engr-in-Charge and colour of sheet to be prior approval from GE.

S&F rolled mild steel work in roof trusses (framed) trussed, purlins, crane gantries, rails and fastenings and heavy duty brackets framing (beam, tee, angle, channel or flat sections) inlcuding distance peices, cleats etc complete all as specified and directed.

S&F Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment and including necessary cutting, bending, welding for raw water sedimantation tray /cover plate as per required shape and size as directed.

M&L for preparation of surface and applying two coats of synthetic enamel paint over a coat of red oxide on new/old steel surfaces exc 10 cm width or girth etc complete all as specified and directed.

S&F Steel rolling shutters thickness of laths 1.25mm MS sheet, with necessary ball bearing, as specified including top cover, anchoring rod, hasp and staple erected in position as indicated but gear operated type with bevel gear box and crank handle, complete including taking down old shutter all as per directed & directed.

M&L for 304 grade stainless steel work as in railing with hand rail, baluster, including cutting, Stainless steel welding and fixing of stainless steel baluster/railing and complete all as specified and directed.

Demolition of Stone masonary/PCC block walling built in cement mortar complete all as specified and directed.

M&L for stone masonary uncoursed, well bonded, bedded and solidly hearted as in drain walls, pedestal for water pipe line built in CM 1:4 complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

Extra for forming fair finished drain or channel 45cm inner girth in cement concrete, using extra cement, incl forms, moulds, mitred /stopped ends etc complete all as specified and directed.

M&L for rendering 20mm thick on stone masonry work in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L for cement concreate 1:3:6 type B1, (using 20mm graded stone aggrigate) as in coping for drain work, sauccer drain and similar works including necessary form work and finishes the surfaces even without using extra cement complete all as specified & directed.

S&F for Factory made smooth finish heavy duty pre-cast R.C.C. Drain/Cable Duct cover/valve pit cover with frame, size exc. 0.50 Sqm and not exc. 2.00 Sqm each, shape rectangular/square as directed by Engr-in-Charge and including necessary cement concrete work for fixing of cover in CM 1:4 ccomplete all as specified and directed.

Raking out cement or cement lime mortar joints/pointing to random rubble or polygonal rubble uncoursed or brought upto courses stone masonry complete all as specified and directed.

M&L for Keyed pointing in CM 1:3 to random rubble or polygonal rubble uncoursed or brought upto course stone masonary wall including preparation of surface including necessary scaffolding arrangement complete all as specified and directed.

FENCING, GATE & COMPOUND WALL WORK (B/R PORTION) Dismantling of Mild steel framed work as in gates, doors, fencing post etc. but excluding framed truss, complete all as specified and as directed.

M&L for framed MS work as in doors or gates of angle or other section with gusset plates, rails braces etc, complete drilled for fixing of steel sheeting or other covering, door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings also fastening and fixing complete all as directed and complete with locking arrangement complete all as specified and directed.

M&L for mild steel black sheet in door 1.60mm thick in steel gate and similar work cut to size, holes punched, including round headed screws, cut nails or revets and fixed to wood or steel framing with plain 40mm lap joints with reveted or welded seams including or turning up, mitred complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate), exc. 10 cm in width and setting in CM 1:6, complete all as specified and directed.

M&L for cement concreate 1:2:4 type B1, using 20mm graded stone aggrigate as in coping including necessary form work and finishes the surfaces even without using extra cement complete all as specified and directed.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off complete all as specified and directed.

M&L for rendering 15mm thick on concrete/PCC block or stone walls surfaces in cement mortar 1:4 finished surfaces even and smooth without using extra cement, complete all as specified & directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43litre/10sqm over and including priming coat of exterior primer applied @ 0.90litre/10Sqm over new/old surfaces of wall including necessary scaffolding required for painting work, height upto 13mtr,safety measures etc complete all as specified and directed.

Dismantling posts or struts of steel or RCC embedded in concrete , stone masonry work of any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Dismantling fencing wire mesh of any type complete all as specified and directed.

Excavating in post holes (or similar holes) each n.exc 0.50 cum gettign out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm watering and removing surplus soil n.exc 50m and making good the surface in hard/dense soil complete all as specified and directed.

M&L plain cement concrete 1:3:6 type C 2, (using 40 mm gde stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for mild steel angles as in post and struts in fencing incl cutting tops and shape as directed incl drilling holes, notching for wire etc conforming to Fe-410W (Gde E-250) etc of any description complete all as specified & directed.

Fixing only chain link fencing including line wires, any mesh size and type and type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed.

Supply only MS galvanished chain link fencing with 4 mm dia and size 40 mm x 40 mm including line wires including strain bolts, binding wire etc complete all as specified and directed.

S&F Galvanised iron 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc, complete all as specified and directed.

All as per item No 104.00 here in above but Restaining, resecuring including making good staples, pins etc, complete all as specified and directed.

S&F round bars 10mm dia ( Fe 410 W gde E 250) and over, cut to length, bent to shape required,including binding and welding with mild steel wire (annealed) not less than 0.9mm dia complete all as specifiedd and directed.

S&F mild steel flat iron (Fe-410-0 or Fe – 310 –0) as in bands / straps / rails for chain link fencing cut required length including necessary drilling holes for fixing bolts all as specified and directed.

M&L for mild steel bolt factory made with hexagonal or square heads at one end and screw the other to be fitted with washer etc and one hexagonal or square not exc 5cm long end dia neck 11 to 15mm etc complete all specified and directed.

M&L for preparation of surface and applying two coats of synthetic enamel paint over a coat of red oxide on steel surfaces exc 10 cm width or girth etc, complete all as specified and directed.

Demolition of Stone masonary walling built in cement mortar complete all as specified and directed.

Raking out cement or cement lime mortar joints/pointing to random rubble or polygonal rubble uncoursed or brought upto courses stone masonry complete all as specified and directed.

M&L for stone masonary uncoursed, well bonded, bedded and solidly hearted as in drain walls built in CM 1:4 complete all as specified and directed.

All as per item No 112.00 here in before item but except stone complete all as specified and directed.

M&L for Keyed pointing in CM 1:3 to random rubble or polygonal rubble uncoused or brought upto course stone masonary wall including preparation of surface including necessary scaffolding arrangement complete all as specified and directed.

INTERNAL ELECTRIFICATION (E&M PORTION) Taking down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials for taking credit and making good disturbed surfaces of walls, floors and roofs etc all as specified and as directed.

Taking down sub main wiring complete including fitting and fixtures, removing materials for taking credit and making good disturbed surfaces of walls, floors, roof etc, all as specified and as directed.

Taking down carefully unserviceable DBs any type/size With MCCBs/MCBs//Isolator etc and disconnecting and making good disturbed surfaces complete all as directed.

M & L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked drawn through PVC concealed conduit/casing caping fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, including modular cover plates with frame and modular flush boxes for mounting for housing the switches, socket outlets, fan regulators etc, all as specified and directed . (a) One light point controlled by one switch.

(b) One fan/Exhaust fan point controlled by one switch and one regulator.

(c) One 3 pin switch socket outlet point 5 Amps on independent board.

(d) One 3 pin switch socket outlet point 5 Amps on same board with other switch.

S & Fix modular switch, single pole,one way 6 Amps capacity

S & Fix modular switch, single pole, one way 16 Amps capacity

S & Fix modular socket, outlet 2 in 1, 6 Amp capacity

S & Fix modular, socket 6A/16A 2 in1, 16 Amp capacity

S & Fix ceiling rose surface backlite 65x50mm 3 terminals complete.

S & Fix modular fan regulator electronic 2 modular type volts AC 50 HZ ,100 Watts, 4 step complete all as directed.

S & Fix LED Batten suitable for mount LED tube rod 1 x 18 watts including necessary electric connections with flexible copper cable 23/0.0076 from ceiling rose to tube light fitting complete all as specifed and directed. Make :- Bajaj Cat Part No - BLRB DB 118 or eqvt in Wipro/Havell/Crompton.

S & Fix LED tube light rod 18 watts with necessary fixing arrangement etc complete all as specifed and directed. Make - Bajaj Cat Part No - BLRB 18W LED or eqvt in Wipro/Havell/Crompton.

S&Fix LED Tube Light Fitting 10 watt, 230 volts, complete with all accessories all as specified & directed. Make :- Bajaj Cat Part No - BCLSB WH 10 NT or eqvt in Wipro/Havell/Crompton.

S & Fix LED street light 30 W CUB type building security light pressure die cast aluminium housing LED street light lumaniries with IP 65 and bracket, nut,bolt,clamp etc complete all accessories and fixing arrengenment all as specified and directed. Make - Bajaj Cat Part No - ENXT P 30L WH CR PC SD Havells Cat Part No -ENDURACITYLITEPLATPLUSSL30WLED757SASYBOPC / Crompton Cat Part No - LTRUMP0030XW or other.

S & Fix LED Street light fitting 90 Watts High performance IP 66 LED street light luminaires with complete acessories all as specified and directed. Make - Bajaj Cat part no :- BRTFG 90W LED CR WW or eqvt in Havells/ Wipro/Crompton.

S & Fix sheet metal enclosure distribution board SPN 2 ways 240 volts, 100 amps rated busbar with IP 43 protection and double door, suitable for mounting MCBs all as specified and as directed.

S & Fix sheet metal enclosure distribution board SPN 4 ways 240 volts, 100 amps rated busbar with IP 43 protection and double door, suitable for mounting MCBs all as specified and as directed.

S & Fix sheet metal enclosure distribution board SPN 8 ways 240 volts, 100 amps rated busbar with IP 43 protection and double door, suitable for mounting MCBs all as specified and as directed.

S & Fix MCB single pole, 240 volts, 6 to 40 Amps, all as specified and as directed.

S & Fix MCB single pole & neutral, 240 volts, 6 to 40 Amps, all as specified and as directed.

S & Fix MCB Triple pole and Neutral 415 volts, 40Amps, all as specified and as directed.

S & Fix MCCB , 4 pole, 415 volts,36 KA, 250 Amps, all as specified and as directed.

M & L for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded on the surface through and including suitable size of PVC Casing caping fixed to walls / roofs / floors / ceiling etc with its accessories all as specified and directed for the following :- (a) 2x1.5 sq mm and 1x1.5 sq mm as earth wire

(b) 2x6 sq mm and 1x6 sq mm as earth wire

Taking down and refixing of Ceiling fan, wall Mounted Fan and Exhaust fan any size/sweep, including oiling, Greasing and cleaning and applying two coats of synthetic enameled paint after preparation of surface complete over a coat of primer complete all as specified and directed.

S & Fix PVC Body Exhaust fan AC single phase 240 volts 900 RPM of size 250 mm sweep with fixed on wall/ventilator and fixing arrangement complete all as specified & directed.

S & Fix steel body Exhaust fan AC single phase 240 volts 900 RPM of size 300 mm sweep with fixed on wall/ventilator and fixing arrangement complete all as specified & directed.

S & Fix for ceiling fan down rods 1.0 M Long of 15 mm dia GI pipe to the existing trusses of any height including necessary welding & fixing with clamps and nut bolts etc complete all as specified and as directed.

S & Fix fans ceiling complete with electronic type regulator and accessories 230 Volt, 1200 mm sweep. BEE 5 Star rated complete fixing arrangement complete all as specified and directed.

M&L for earthing with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground earth pit not less than 2.25M deep below ground level with top edge of the plate not less than 1.5M below normal ground level connected to galvanised strip 32x6mm by means of nuts, bolts, checknuts, washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part I connected to earthing test point including excavation/ earth work in any strata removal of surplus earth, GI pipe for watering and funnel, PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 in cover slab 50mm thick with 8mm dia TMT bar @ 75mm spacing both ways with 40mm dia light grade GI protection pipe and 20mm dia light grade GI pipe for watering all as specified and directed. Note :- Cost of earth lead and protection pipe upto 7.5m shall deemed to be included in quoted rate.

EXTERNAL ELECTRIFICATION (E&M PORTION) Supply and Laying and testing cable XLPE insulated heavy duty electric cables with multistanded aluminium conductor, 1100 volts grade, cross sectional area 16 sqmm, 4 core cable connecting lugs, glands,jointing materials etc, laid on surface,wall, floors, roof, ducts and fixing using clamps, saddle complete all as directed by Eng-in-charge.

All as per item No 147.00 here-in-before but corss sectional area of cable 6 Sqmm, 2 core

All as per item No 147.00 here-in-before but corss sectional area of cable 4 Sqmm, 2 Core

All as per item No 147.00 here-in-before but corss sectional area of cable 10 sq mm 2 core

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth and getting out in Hard / dense or any type of soil including forming bottom surface etc complete all as specified and directed.

Returning, filling in including spreading, levelling ,watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 50 mtr above the starting point complete all as specified and directed.

Supply & Laying 40 mm outside dia double wall corrugated pipe (DWC) ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe all as per site requirement complete all as specified and directed.

M &L for GI pipe 40mm dia ''light grade'' for road crossing / on wall / on pole for cable protection complete all as specified and directed.

Dismantling the old unserviceable LT Panel Board and Supply Fabricate, install, connect, test and commission Indoor type dust & Vermin proof LT electrical panel board, 1100 volts, 50 Hz AC supply, fully compartmentalised for cable chamber and busbar chambers with adequate space made out of 3 mm thick CRCA sheet for like all over body, CRCA powder coated all over the all surfaces only including suitable angle iron/ flat iron frame work/ supports bottom 50x50x6 mm MS channel as base and chamber for metering equipment complete suitable for mounting following switch gear items internally connected with suitable capacity aluminium strip/ rods insulated and connection wirings with FRLS copper conductor complete mounted on PCC pillars foundation, cable connection using new lugs complete with danger notice all as specified and comprising of the followings:-Note: (i) Existing cables which removed from old panel board will be fixed with new lugs during fixing in new panel board (if required) (ii) Getting of approval for Panel board drawing from Engr-in-Charge is necessary before fabrication. (iii) All swith gears should be fixed with 06 mm thick Fibre sheet Make: Any CPRI approved (a) LED/Neon indicator bulb in RYB Colour - 1 Set. (b) 4 No aluminium Bus bar 200 amps with chamber (c) Digital Multi function meter for showing Amps (upto 500 Amps) and Voltage (upto 500 voltage) with suitable CT and PT. (d) MCCB 4 Pole, 415 V, Adjustable thermal & adjustable magnetic type, 100A with breaking capacity 25 KA - 03 Nos

Suppy, errecting in truly vertical position steel tubular swaged pole 8.5 mtr long with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP 55, including painting with anti corrosive paint internally complete and externally up to planting depth, alternative white & black strips of 30 cm width upto 1.5 mtr above ground level all as required at site including dismantling of old steel tubular poles removing from site complete all as specified and directed.

Supply & Laying synthetic rubber insulated mat 3mm thick for voltage up to 22 KV for electric shock safety of size 2X1m. complete all as specified and as directed.

Supply and Fix LED Solar light fitting die cast aluminium body having Min 28 watts Solar monocrystalline module panel with 11 watts LED power having >175 lumens per watt including 12 volts Lithium ferro phospate battery min IP 65 rating, including 6 mtr suitable GI/steel pole and necessary foundation works as recommended by manufacturer. Make: Philips Model: BRP710 LED20 CW MR S1 12V LFP AIO Solar Equip IN -with Sensor or equivalant in Wipro/Crompton

Supply & Fixing 6 KG ABC type fire Extinguisher of corbon oxide suitable for electric fire complete fixing arrangement all as directed by Engr- in- charge.

Supply and laying in trenches GI tubing 'Medium grade' of following sizes with all fittings complete (Fittings e.g socket, Tee, reduceres, elbows, nipple, plug etc ( excavation of earth work shall be measured and paid seperately). (a) GI pipe 40mm bore

Supply & lay cast iron pipes with spigot and socket ends centrifugally cast Class A of following sizes in any length laid in trenches complete all as specified and directed. (a) CI Pipe Class A 300 mm bore

(b) CI Pipe Class A 100 mm bore

(c) CI Pipe Class A 80 mm bore

Supply and fixing cast Iron rising spindle sluice valves flanged end with iron wheel head, screwed both ends for iron pipes 30 mm dia complete all as specified and directed.

Cutting chases on brick wall/ stone masonary, for concealed water tubing and making good , with CM 1:3, cutting exc 10cm but not exc 20cm girth complete all as specified and directed.

Supply Boulders 7cm to 15cm dia and laid, compacted with suitable filters complete all as specified and directed.

S&F Cast Iron Air Valves with two air Outlets, 50 mm dia bore and fixing Up in cast iron water supply mains complete all as specified and directed.

Supply & fixing Brass type Nozzel 8 mm /10mm with complete fixing arrangement complete all as sepcified and directed.

Supply and fix water pressure gauge along with stop cock of same size, necessary GI fittings and making hole at new place if required on GI/MS/CI pipe at places as directed by Engineer-in-Charge. Make- FEIBIG or equivalent & approved.

Supply and fixing of Gun metal gate valves with iron wheel head, screwed both ends for iron pipes complete, size of GM gate valve 40mm complete all as specified and directed.

M& L Bends (any type, radius and angle) tapers any type, (straight, bend,increasing decreasing or double socket etc.) Tee pieces single branc. "Y" junction ,double branch, cross (all socket and spigot,collers,caps and plugs complete all as specified and directed.

Mehta and Co.

J.G.Goel

SHINDE DHEERAJKUMAR SIDRAM