REPAIR TO PATH HARD STANDING INTERLOCKING TILES DRAINS AND MISC BR WORKS AT SECTOR B UNDER AGE BR II OF GE 865 EWS

Amount

Taking down cement plaster of any description on brick or stone walls, concrete surfaces including racking out joints, hacking for key, scrubbing down with water remove dust, debries/rubbish etc, complete all as specified and as directed.

Rendering 15 mm thick on fair faces of brick work or stone masonary work, finished even and smooth (without using extra cement) on walls in cement mortar (1:4), complete all as specified and directed by Engr-in-Charge.

M&L for two coats cement base paint over a coat of primer on newly plastered surfaces of wall including preparation of surfaces including curing before and after applying each coat complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles/concrete block walling complete all as specified and as directed by Engr-in-Charge.

M&L for pre cast cement concrete block masonary of 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) with soild blocks, exc.10cm in width, set and jointed in cement mortor 1:6 complete all as specified and directed.

M&L for pre cast cement concrete block masonary of 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) with soild blocks, using old concrete blocks obtained from the demolition, exc.10cm in width, set and jointed in cement mortor 1:6 complete all as spd and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and as directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6, using old stones/boulders obtained from the demolition complete all as specified and as directed.

M&L for raised pointing to random or polygonal rubble, uncoursed or brought upto courses in CM 1:4 complete all as specified and as directed.

Demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and Removing demolished material to a distance and depositing out site of MoD land Where directed at a level not exceeding 100 metre above the starting point complete all as specified and directed by Engineer-in-Charge.

M&L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) 100 mm thick , as in floors and pavings complete all as specified and directed.

M&L for plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) 75 mm thick sub base, sub floor and pavings complete all as specified and directed.

M&L forming construction joint 30mm deep x 10mm wide filled with sealing compound Grade B, complete all as specified and directed by Engineer-in-Charge.

M&L Cement concrete 1:3:6 type C1 using 20mm graded stone crushed aggregate in plinth protection, 75mm thick, finished even and smooth using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and as directed.

M&L for providing plain cement concrete type C1, 1:3:6 (using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

M&L for coloured chequred cement concrete tiles, machine pressed, factory made of size 300mm X 300mm X 25mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & no pigments and laid over and including 20mm thick cement screed base (1:4) complete all as specified and as directed by Engr-in -Charge.

M&L for coloured endura tiles as approved make of size 300mm X 300mm/400mmx400mm X 10mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & no pigments and laid over and including 20mm thick cement screed base (1:4) complete all as specified and as directed by Engr-in -Charge.

M&L for machine pressed / vibro mechanically floated precast concrete interlocking cement paver block ISI marked, any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 Grade, with topping of grey cement and pigment, laid over and including 25mm thick sand cushioning complete. Shape pattern of laying shall be approved by Engineer-in-charge.

M&L for machine pressed / vibro mechanically floated precast concrete interlocking cement paver block ISI marked, any shape and size conforming to IS 15658-2006 of 80mm thickness, M-40 Grade, with topping of grey cement and pigment, laid over and including 25mm thick sand cushioning complete. Shape pattern of laying shall be approved by Engineer-in-charge.

M&L for Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed by Engr-in -Charge.

M&L for providing plain cement concrete type C2, 1:3:6 (using 40mm graded crushed stone aggregate) as surface channels and drain including demolition of exisitng cement concrete (unreinforced) of any description and in any position not otherwise specially provided for and removing debris outside the MD land complete all as specified and as directed.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc.(inner girth only measured) complete all as specified and as directed.

M&L for factory made precast PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregates, as in kerb stone of size 300 x 300x 100mm thick (width and depth of kerb stone shall be 100mm & 300mm respectively) set in CM (1:4) including necessary form works and earth work complete all as specified and directed by Engr-in-Charge.

M&L for one coat of synthetic enamel paint of any description on old plastered or concrete surface of any description over 10cm girth or width not otherwise described including preparation, complete all as specified and directed by Engineer-in-Charge

M&L for two coats of synthetic enamel paint of any description on new plastered or concrete surface of any description over 10cm girth or width not otherwise described over a coat of primer , complete all as specified and directed by Engineer-in-Charge

M&L for applying one coat of oil exterior emulsion paint (Apex Ultima) on old plastered or treated surface of desired finished complete all as specified and directed by Engineer-in-Charge

Rampal Singh Contractor

PARIDHI CONSTRUCTION

M/S SHAMSHER ALI SUFI

KHUSHBU TRADERS

M/S Praveen Kumar and Sons

M/S RIGDOL CONSTRUCTION

THINLES OTZER

M/S MOHD KARIM

M/S LIBE & CO