Supply, installation and maintenance of Mechanical Compactors, Storage Systems, Furniture Articles, Solid Teak Wood Benches for public seating in New Judicial Complex Tower of Justice at Gurugram

Overall size of Personal Locker Unit shall be of dimensions 900mm(W) X 400mm(D) X 1850mm(H) having 15 locker unit. Locking shall have Pad lock . Material shall be CRCA 0.8 mm thickness. Shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum. Finish shall be powder coating Interpon 700 RAL 9002 EC150N semi glossy of thickness 60µ-80µ. Handle/Label holder shall be aesthetically appealing Snap fit ABS plastic handle. Ventilation shall be attractive punched pattern for ventilation.

Providing and placing workstation table in completely knock down conditions with an overall size 1320mm X 660mm X 1200mm that is to be assembled at site. The work top shall have the size 1200mm X 600mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 525mm X 350mm. The trey shall be operated on keyboard channel. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in the front side of user as well as on the both sides of the user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with Interpon 700 RAL 9002 EC150N semi glossy of thickness 60µ-80µ. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways and 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) and marker board provided at front of the user. Laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Fixed type pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close and open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 468mm X 284mm with 18mm thick Pre-laminated particle board. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. n

Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade `D` confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to  undercarriage. Compactor height from ground should be 2190 mm (2080 body plus 65 undercarriage). The body including shelves shall be given antirust surface treatment and powder coated with epoxy polyester powder coating i.e. Interpon 700 RAL 9002 EC150N semi glossy of thickness 60µ-80µ. It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets and shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts and bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. 1 Bay Single static Fixed 1200 mm X 455 mm X 2190 mm (1 no.) 1 Bay Double movable 1200mm X 910mm X 2190mm (5 nos) 1 Bay Single Last Movable (Lockable) 1200mm X 455mm X 2190mm (1 no.)

Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade `D` confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to  undercarriage. Compactor height from ground should be 2190 mm (2080 body plus 65 undercarriage). The body including shelves shall be given antirust surface treatment and powder coated with epoxy polyester powder coating i.e. Interpon 700 RAL 9002 EC150N semi glossy of thickness 60µ-80µ. It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets and shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts and bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. 1 Bay Single static Fixed 1200 mm X 455 mm X 2190 mm (1 no.) 1 Bay Double movable 1200mm X 910mm X 2190mm (4 nos) 1 Bay Single Last Movable (Lockable) 1200mm X 455mm X 2190mm (1 no.)

Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade `D` confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to  undercarriage. Compactor height from ground should be 2190 mm (2080 body plus 65 undercarriage). The body including shelves shall be given antirust surface treatment and powder coated with epoxy polyester powder coating i.e. Interpon 700 RAL 9002 EC150N semi glossy of thickness 60µ-80µ. It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets and shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts and bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. 1 Bay Single static Fixed 1200 mm X 455 mm X 2190 mm (1 no.) 1 Bay Double movable 1200mm X 910mm X 2190mm (1 nos) 1 Bay Single Last Movable (Lockable) 1200mm X 455mm X 2190mm (1 no.)

Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade `D` confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to  undercarriage. Compactor height from ground should be 2190 mm (2080 body plus 65 undercarriage). The body including shelves shall be given antirust surface treatment and powder coated with epoxy polyester powder coating i.e. Interpon 700 RAL 9002 EC150N semi glossy of thickness 60µ-80µ.   It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets and shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts and bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. 2 Bay Single static Fixed 2400mm X 455mm X 2190mm (1 no.) 2 Bay Double movable 2400mm X 910mm X 2190mm (5 nos.) 2 Bay Single Last Movable (Lockable) 2400mm X 455mm X 2190mm (1 no.)

Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade `D` confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to  undercarriage. Compactor height from ground should be 2190 mm (2080 body plus 65 undercarriage). The body including shelves shall be given antirust surface treatment and powder coated with epoxy polyester powder coating i.e. Interpon 700 RAL 9002 EC150N semi glossy of thickness 60µ-80µ. It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets and shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts and bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. 1 Bay Single static Fixed 915 mm X 455 mm X 2190 mm (1 no.) 1 Bay Double movable 915mm X 910mm X 2190mm (2 nos) 1 Bay Single Last Movable (Lockable) 915mm X 455mm X 2190mm (1 no.)

Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade `D` confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to  undercarriage. Compactor height from ground should be 2190 mm (2080 body plus 65 undercarriage). The body including shelves shall be given antirust surface treatment and powder coated with epoxy polyester powder coating i.e. Interpon 700 RAL 9002 EC150N semi glossy of thickness 60µ-80µ. It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets and shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts and bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. 1 Bay Single static Fixed 915 mm X 455 mm X 2190 mm (1 no.) 1 Bay Double movable 915 mm X 910mm X 2190mm (1 nos) 1 Bay Single Last Movable (Lockable) 915 mm X 455mm X 2190mm (1 no.)

Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade `D` confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to  undercarriage. Compactor height from ground should be 2190 mm (2080 body plus 65 undercarriage). The body including shelves shall be given antirust surface treatment and powder coated with epoxy polyester powder coating i.e. Interpon 700 RAL 9002 EC150N semi glossy of thickness 60µ-80µ. It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets and shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts and bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. 2 Bay Single static Fixed 2400mm X 455mm X 2190mm (1 no.) 2 Bay Double movable 2400mm X 910mm X 2190mm (4 nos.) 2 Bay Single Last Movable (Lockable) 2400mm X 455mm X 2190mm (1 no.)

Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade `D` confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to  undercarriage. Compactor height from ground should be 2190 mm (2080 body plus 65 undercarriage). The body including shelves shall be given antirust surface treatment and powder coated with epoxy polyester powder coating i.e. Interpon 700 RAL 9002 EC150N semi glossy of thickness 60µ-80µ.  It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets and shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts and bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. 1 Bay Single static Fixed 1200 mm X 455 mm X 2190 mm (1 no.) 1 Bay Double movable 1200mm X 910mm X 2190mm (2 nos) 1 Bay Single Last Movable (Lockable) 1200mm X 455mm X 2190mm (1 no.)