Jet Pump Monoblock Pump Bare Pump Underwater Pump VT Pump India mark 2 Mark 3 Hand Pump repairing and Spare Parts ZP Bhandara

Amount

Jet Pump,Monoblock Pump, Bare Pump Underwater Pum all Submit Rate as per GSDA-ITEM Sheet

India Mark -2 & 3 Hand Pump Repairing Drive out the Pipe line with diameter of 65.0 m.m.

Drive out the Pipe line with diameter of 65.0 m.m which fell in well.

Drive out the Pipe line with diameter of 32.0 m.m from which fell in well.

Drive out the Pipe line with diameter of 32.0 m.m from well.

Repairing of jet Motor Pump & PipelineDrive out inner Pipeline with Jet assembly of JetPump from 1.0 Hp to 5.0 Hp well.

To fit the inner and outer pipeline of the jet Pump in 1.0 Hp to 5.0 Hp well.

To insert inner pipeline of Jetpump in well. (after repairing.)

To insert inner & outer pipeline of Jetpump in well. (after repairing.)

To pull out the Stucked, fell or caught in dreg Pump Set. ( Contracter use their own tools.)

To increse or reduse the pipe line of Jet Pump inh well. ( For every 3.0 m. )

To submit in the office Jet pump, Motor pipeline, starter panel board tin & other assesaries of Laghu Panee Purwatha Yojna in well.

New pump set (Upto 1.0 to 5.0 HP) to fit in well, to give panel wiring arthig test report & start after electric supply. (Z.P. provides Pumpset panel, arthing material G.I. wire, plate, pipe and other assesaries.)

To drive out motor and pump from Jet pump

To fit 1.0 HP to 5.0 HP Jet motor pump.

To rewinding electric motor with copper wire , above rate valid for without returning old copper wire, 1.0 HP to 5.0 HP open pump motor rewinding.

To open the Jet motor, over oiling, fitting and testing

Roter pump shaft turning and polishing.

To make upper and lower bush of baring cover sit and housing of Jet pump.

To test electric pump on site ( transport and with minor repairing)

To repaire panel board & starter of all types motor & Any HP control panel starter minor repairing to fit grif set, rottery swich, contracter plate, ampear meter, volt meter, on-off switch, fuse and minor wiring.

Starter panel board main repairing & to fit coilrelay, single phasing preventer water label guard & totle wiring of 1.0 HP to 10.0 Hp pump.

Starter panel board main repairing & to fit coilrelay, single phasing

preventer water label guard & totle wiring of 10.0 HP to 30 Hp pump.

preventer water label guard & totle wiring of 31.0 HP to 40 Hp pump.

To remove tin shed flashing of pump if necessary and fit as it is after work.

To remove handpump with pipeline for flashing and insert 10 feet G.I. pipeline towards 32 m.m. dimeter& remove after flashing and fit handpump as it is before.

To remove handpump for capacity test and after testing fit as it is before.

Single phase 1 HP to 2 Hp electric pump capacity test for regular three Hour with help of generator

Yield Test 1 HP to 2 Hp electric pump capacity test for regular three Hour with help of generator with necc equip

Yield Test 2 HP to 5 Hp electric pump capacity test for regular three Hour with help of generator with necc equip

Yield Test 2 HP to 5 Hp electric pump capacity test for regular three Hour without help of generator with necc equip

Spare parts of Jet Pump Baring upper

Baring lower

Empelor key

Pump bush

Air fan ( with PVC pin)

Stand nut kit

Nut bolt kit

Air cock

Pressure regulating volve

Pressure regulating difrom

Baring plate top / bottom

Jet assembly packer type full

Packer foot volve

Packer rubber seal set

Packer backet set

Gland rope

Rubber packing set

Gland rope plate

Empelor

D) Other material G. I. coplling heavy duty

iii) 50 m.m.

vii) 125 m.m.

viii) 150 m.m.

Bend heavy duty

iii) 50 m.m.

vii) 125 m.m.

viii) 150 m.m.

3) Foot volve : i) 32 m.m.

iii) 50 m.m.

vii) 125 m.m.

viii) 150 m.m.

Wooden board 3 x 2 f x ½ “

Iron box 18 guage tin 3f x 2f x 1f

G.I.Pipe 1½“ / 1¼ “ cutting threding

G.I.Pipe 2“ cutting threding

G.I.Pipe 2½“ / 3 “ cutting threding

E) Submercible Pump Repairing : 1.0 HP to 3.5 HP

4.0 HP to 5.0 HP

6.0 HP to 10.0 HP

11.0 HP to 15.0 HP

16.0 HP to 20.0 HP

21.0 HP to 30.0 HP

31.0 HP to 50.0 HP

F) To Remove Motor Pump Set with Pipeline from well: 1 HP to 6.0 HP

7.0 HP to 15 HP

16.0 HP to 30.0 HP

31.0 HP to 50.0 HP

G) To pull out the Stuck, fell or caught in dreg Pump Set with pipeline from well: 1 HP to 6.0 HP

2) 7.0 HP to 15 HP

3) 16.0 HP to 30.0 HP

4) 31.0 HP to 50.0 HP

H) To fit motor pump in well with pipe line : 1) 1 HP to 6.0 HP

2) 7.0 HP to 15 HP

3) 16.0 HP to 30.0 HP

4) 31.0 HP to 50.0 HP

I) To increase or reduse pipeline of submercible pump in well Rate 3 meter / per pipe: 1 HP to 6.0 HP

7.0 HP to 15 HP

16.0 HP to 30.0 HP

31.0 HP to 50.0 HP

J) To submit in the office Jet pump, : 1 HP to 7.5 HP

8.5 HP to 15 HP

16.0 HP to 30.0 HP

31.0 HP to 50.0 HP

K) New pump set (Upto 1.0 to 5.0 HP) :1 HP to 7.5 HP

8.5 HP to 15 HP

16.0 HP to 30.0 HP

31.0 HP to 50.0 HP

L) To open sub motor, repairing, fitting and testing.: 1 HP to 7.5 HP

8.5 HP to 15 HP

16.0 HP to 30.0 HP

31.0 HP to 50.0 HP

M) To open sub pump, repairing, fitting and testing.:1) 1 HP to 7.5 HP

2) 8.5 HP to 15 HP

3) 16.0 HP to 30.0 HP

4) 31.0 HP to 50.0 HP

N) To repaire sub motor and sub pump:To sub motor / pump bush fitting per

Damage stater repairing

Roter shaft turning and polishing

Damage roter repairing (Rewinding)

Sub pump shaft turning & polishing

To joint cable with kit

O) Sub motor & sub pump spare parts1 to 5 HP: i) Sub motor bush

ii) sub pump bush

Thirst baring block

Thirst baring full

Block

Upper stage casing

Lower stage casing

Middle stage casing

i) Empelor

ii) Brass Empelor

Nekring

Defuser

Pump key

Rubber parts kit

Submotor base

Stenner

Male- Female bush

Male- Famale key

NRV stage casing

Stud big

Stud small

Motor bush housing

i) Upper

ii) Lower

Alen srew

SS Slive motor /pump

SS Slive cover

O) Sub motor & sub pump spare parts1 to 7.5 HP: i) Sub motor bush

ii) sub pump bush

Thirst baring block

Thirst baring full

Block

Upper stage casing

Lower stage casing

Middle stage casing

i) Empelor

ii) Brass Empelor

Nekring

Defuser

Pump key

Rubber parts kit

Submotor base

Stenner

Male- Female bush

Male- Famale key

NRV stage casing

Stud big

Stud small

Motor bush housing

i) Upper

ii) Lower

Alen srew

SS Slive motor /pump

SS Slive cover

O) Sub motor & sub pump spare parts 8 to15 HP : i) Sub motor bush

ii) sub pump bush

Thirst baring block

Thirst baring full

Block

Upper stage casing

Lower stage casing

Middle stage casing

i) Empelor

ii) Brass Empelor

Nekring

Defuser

Pump key

Rubber parts kit

Submotor base

Stenner

Male- Female bush

Male- Famale key

NRV stage casing

Stud big

Stud small

Motor bush housing

i) Upper

ii) Lower

Alen srew

SS Slive motor /pump

SS Slive cover

O) Sub motor & sub pump spare parts 16 to30 HP: i) Sub motor bush

ii) sub pump bush

Thirst baring block

Thirst baring full

Block

Upper stage casing

Lower stage casing

Middle stage casing

i) Empelor

ii) Brass Empelor

Nekring

Defuser

Pump key

Rubber parts kit

Submotor base

Stenner

Male- Female bush

Male- Famale key

NRV stage casing

Stud big

Stud small

Motor bush housing

i) Upper

ii) Lower

Alen srew

SS Slive motor /pump

SS Slive cover

1) Three ply coreflat flexible submercible cable: i) 1.5 sq.m.m.

ii) 2.5 sq.m.m.

iii) 4 sq.m.m.

iv) 6 sq.m.m.

v) 10 sq.m.m.

vi) 1.5 sq.m.m.

1) Three ply coreflat : Arm cable :i) 1.00 sq.m.m.

ii) 1.50 sq.m.m.

iii) 2.50 sq.m.m.

iv) 4.00 sq.m.m.

v) 6.00 sq.m.m.

vi) 10.00 sq.m.m.

vii) 16.00 sq.m.m.

viii) 25.00 sq.m.m.

ix) 35.00 sq.m.m.

x) 50.00 sq.m.m.

Copper wire P.V.C. insulated & P.V.C. coated: i) 3/20

Copper wire P.V.C. insulated & P.V.C. coated: ii) 7/20

Copper wire P.V.C. insulated & P.V.C. coated: iii) 7/16

27) New Pump Shaft i) 1.5 HP to 6 HP

27) New Pump Shaft ii) 7.5 HP to 15 HP

27) New Pump Shaft iii) 16 HP to 30 HP

Borewell Protecting Plate

Borewell Protecting Cover

P) 25.0 HP to 40 HP V.T. Motor pump set repairing 25HP: Drive out V.T. Motor from well

V.T. Pump fit in well

Drive out colume assembly with pipeline from well

To fit colume assembly with pipeline in well

To open V.T. Motor

V.T. Motor fitting & testing

Bowl assembly fitting & testing

To open bowl assembly

V.T. Pump rewinding with copper wire. Without returning old copper wire

Allignment checking & repairing

i) Line shaft

ii) Colume pipe

iii) Oil tube

Cutting & Threading

i) Line shaft (R.H./L.H)

ii) Colume pipe (R.H./L.H)

iii) Oil tube (R.H./L.H)

To fit new flage, threading coller, welding, nutbolt in colume pipe

To Making ,Bearing sheet on lathe machine

Bearing plate both side

P) 25.0 HP to 40 HP V.T. Motor pump set repairing 35HP: Drive out V.T. Motor from well

V.T. Pump fit in well

Drive out colume assembly with pipeline from well

To fit colume assembly with pipeline in well

To open V.T. Motor

V.T. Motor fitting & testing

Bowl assembly fitting & testing

To open bowl assembly

V.T. Pump rewinding with copper wire. Without returning old copper wire

Allignment checking & repairing

i) Line shaft

ii) Colume pipe

iii) Oil tube

Cutting & Threading

i) Line shaft (R.H./L.H)

ii) Colume pipe (R.H./L.H)

iii) Oil tube (R.H./L.H)

To fit new flage, threading coller, welding, nutbolt in colume pipe

To Making ,Bearing sheet on lathe machine

Bearing plate both side

P) 25.0 HP to 40 HP V.T. Motor pump set repairing 40HP : Drive out V.T. Motor from well

V.T. Pump fit in well

Drive out colume assembly with pipeline from well

To fit colume assembly with pipeline in well

To open V.T. Motor

V.T. Motor fitting & testing

Bowl assembly fitting & testing

To open bowl assembly

V.T. Pump rewinding with copper wire. Without returning old copper wire

Allignment checking & repairing

i) Line shaft

ii) Colume pipe

iii) Oil tube

Cutting & Threading

i) Line shaft (R.H./L.H)

ii) Colume pipe (R.H./L.H)

iii) Oil tube (R.H./L.H)

To fit new flage, threading coller, welding, nutbolt in colume pipe

To Making ,Bearing sheet on lathe machine

Bearing plate both side

Q) 25 HP to 40 HP V.T. Pum Spare Part 25HP : 1) V.T. Motor baring

i) Upper

ii) Lower

Discharge & sectioncase Baring bush gun metal

Water seal (Oil water separater)

Line Shaft

Oil Tube

T.T. Plate cast iron

Brain rubber bush (spider)

Net (cast iron)

Nut bolt ¾“ x 2 “

Nut bolt ¾“ x 6 “

Rubber Shit

T.T. Plate Bush

Neck Ring (Gun Metal)

Impelor (Gun Metal)

Browl assembly casing

6” colume pipe M.s.

8” colume pipe M.s.

Transformer Oil

Pump Colet

Shaft Tube Oil 10 no.

Impelor pump shaft

Litern Ring

Gide spider

Colume Pipe coplling

Line shaft coplling

Oil tube baring

Glad nut

Top Oil Tube

Spider Baring Bush

Guide Spider Rubber Bush with Sirclip

Rubber Bush/ Baring

Line Shaft Slive S.S.

Water Lubricating Tube

Stuffing Box Bush & with gaskit

Stuffing Box Baring

Latern Ring

Sole Plate

Base Plate

Water Deflector

Q) 25 HP to 40 HP V.T. Pum Spare Part 25HP : 1) V.T. Motor baring

i) Upper

ii) Lower

Discharge & sectioncase Baring bush gun metal

Water seal (Oil water separater)

Line Shaft

Oil Tube

T.T. Plate cast iron

Brain rubber bush (spider)

Net (cast iron)

Nut bolt ¾“ x 2 “

Nut bolt ¾“ x 6 “

Rubber Shit

T.T. Plate Bush

Neck Ring (Gun Metal)

Impelor (Gun Metal)

Browl assembly casing

6” colume pipe M.s.

8” colume pipe M.s.

Transformer Oil

Pump Colet

Shaft Tube Oil 10 no.

Impelor pump shaft

Litern Ring

Gide spider

Colume Pipe coplling

Line shaft coplling

Oil tube baring

Glad nut

Top Oil Tube

Spider Baring Bush

Guide Spider Rubber Bush with Sirclip

Rubber Bush/ Baring

Line Shaft Slive S.S.

Water Lubricating Tube

Stuffing Box Bush & with gaskit

Stuffing Box Baring

Latern Ring

Sole Plate

Base Plate

Water Deflector

Q) 25 HP to 40 HP V.T. Pum Spare Part 40HP: 1) V.T. Motor baring

i) Upper

ii) Lower

Discharge & sectioncase Baring bush gun metal

Water seal (Oil water separater)

Line Shaft

Oil Tube

T.T. Plate cast iron

Brain rubber bush (spider)

Net (cast iron)

Nut bolt ¾“ x 2 “

Nut bolt ¾“ x 6 “

Rubber Shit

T.T. Plate Bush

Neck Ring (Gun Metal)

Impelor (Gun Metal)

Browl assembly casing

6” colume pipe M.s.

8” colume pipe M.s.

Transformer Oil

Pump Colet

Shaft Tube Oil 10 no.

Impelor pump shaft

Litern Ring

Gide spider

Colume Pipe coplling

Line shaft coplling

Oil tube baring

Glad nut

Top Oil Tube

Spider Baring Bush

Guide Spider Rubber Bush with Sirclip

Rubber Bush/ Baring

Line Shaft Slive S.S.

Water Lubricating Tube

Stuffing Box Bush & with gaskit

Stuffing Box Baring

Latern Ring

Sole Plate

Base Plate

Water Deflector

i) Drive out 1 HP to 3 HP Monoblock Pump

ii) Drive out 4 HP to 10 HP Monoblock Pump

ii) 2 to 3 HP Monoblock Motor Rewinding

iii) 4 to 5 HP Monoblock Motor Rewinding

iv) 6 to 7½ HP Monoblock Motor Rewinding

v) 8 to 10 HP Monoblock Motor Rewinding

Monoblock Pump Open, Repairing, Fitting & Testing i) 1 to 1½ HP

Monoblock Pump Open, Repairing, Fitting & Testing ii) 2 to 5 HP

Monoblock Pump Open, Repairing, Fitting & Testing iii) 6 to 10 HP

Roter Pump Shaft Turning & Polishing i) 1 to 5 HP

Roter Pump Shaft Turning & Polishingii) 6 to 10 HP

To make Monoblock Pump Bush & Housing (Baring) i) 1 to 1½ HP

To make Monoblock Pump Bush & Housing (Baring) ii) 2 to 5 HP

To make Monoblock Pump Bush & Housing (Baring) iii) 6 to 10 HP

To Fit New Pump Set i) 1 to 1½ HP

To Fit New Pump Set ii) 2 to 5 HP

To Fit New Pump Set iii) 6 to 10 HP

T) Monoblock Pump Spare Parts Baring 1 to 1½ HP(Driving side)

Baring (Driven side)

Impelor Key

Pump Bush

Air Fan

Sturnut Key

Baring Plate both side 1 item

Water seal

Gland Rope

Gland Bush

Gland Plate

Roter fitted shaft

Latern Ring

Impelor brass

Impelor C.I.

Defuser

Baring housing

Neck Ring

Foot volve

Fluge (Dilevery/ suction)

Shaft sleve

Delivery casing

Stater Fitted motorbody

Spacer

Fan cover

Water Deflector

T) Monoblock Pump Spare Parts 2 to 3 HP Baring (Driving side)

Baring (Driven side)

Impelor Key

Pump Bush

Air Fan

Sturnut Key

Baring Plate both side 1 item

Water seal

Gland Rope

Gland Bush

Gland Plate

Roter fitted shaft

Latern Ring

Impelor brass

Impelor C.I.

Defuser

Baring housing

Neck Ring

Foot volve

Fluge (Dilevery/ suction)

Shaft sleve

Delivery casing

Stater Fitted motorbody

Spacer

Fan cover

Water Deflector

T) Monoblock Pump Spare Parts 4 to 5 HP Baring (Driving side)

Baring (Driven side)

Impelor Key

Pump Bush

Air Fan

Sturnut Key

Baring Plate both side 1 item

Water seal

Gland Rope

Gland Bush

Gland Plate

Roter fitted shaft

Latern Ring

Impelor brass

Impelor C.I.

Defuser

Baring housing

Neck Ring

Foot volve

Fluge (Dilevery/ suction)

Shaft sleve

Delivery casing

Stater Fitted motorbody

Spacer

Fan cover

Water Deflector

T) Monoblock Pump Spare Parts Baring 6 to 7½HP (Driving side)

Baring (Driven side)

Impelor Key

Pump Bush

Air Fan

Sturnut Key

Baring Plate both side 1 item

Water seal

Gland Rope

Gland Bush

Gland Plate

Roter fitted shaft

Latern Ring

Impelor brass

Impelor C.I.

Defuser

Baring housing

Neck Ring

Foot volve

Fluge (Dilevery/ suction)

Shaft sleve

Delivery casing

Stater Fitted motorbody

Spacer

Fan cover

Water Deflector

T) Monoblock Pump Spare Parts Baring 8 to 10HP(Driving side)

Baring (Driven side)

Impelor Key

Pump Bush

Air Fan

Sturnut Key

Baring Plate both side 1 item

Water seal

Gland Rope

Gland Bush

Gland Plate

Roter fitted shaft

Latern Ring

Impelor brass

Impelor C.I.

Defuser

Baring housing

Neck Ring

Foot volve

Fluge (Dilevery/ suction)

Shaft sleve

Delivery casing

Stater Fitted motorbody

Spacer

Fan cover

Water Deflector

U) Bare Pump Repairing To drive out bare pump i) 10 to 20 HP

ii) 21 to 50 HP

Bare Pump to open, repairing, fitting & Testing i) 10 to 20 HP

ii) 21 to 50 HP

Pump shaft turning & polishing i) 10 to 20 HP

ii) 21 to 50 HP

To make pump bush & housing (baring) i) 10 to 20 HP

ii) 21 to 50 HP

To fit new bare pump i) 10 to 20 HP

ii) 21 to 50 HP

Pump repairing & fitting i) 10 to 20 HP

ii) 21 to 50 HP

To make gland bush housing i) 10 to 20 HP

ii) 21 to 50 HP

Drive out bare pump pipe line with foot volve i) 10 to 20 HP

ii) 21 to 50 HP

To fit bare pump pipeline with foot volve i) 10 to 20 HP

ii) 21 to 50 HP

V) Bare Pump spare parts 10 to 15 HP Baring (Ball baring)

Rolar baring

Impelor key

Pump bush

Stud nut

Nut bolt kit

Air cock

Base plate

Water seal

Gland bush

Gland plate

Pump shaft

Latern Ring

Impelor brass

Impelor (C.I)

Difuser

Baring housing

Neck ring (small)

Neck ring (big)

Flasher

Foot volve

Check nut

Impelor housing

Roter casing

Roter

Delevery casing

Stuffing box bush

Shaft sleve

Water deflector

Cuplling half flexible

Baring cover

Grees cup

Flage section/ delivery

V) Bare Pump spare parts 16 to 20HP Baring (Ball baring)

Rolar baring

Impelor key

Pump bush

Stud nut

Nut bolt kit

Air cock

Base plate

Water seal

Gland bush

Gland plate

Pump shaft

Latern Ring

Impelor brass

Impelor (C.I)

Difuser

Baring housing

Neck ring (small)

Neck ring (big)

Flasher

Foot volve

Check nut

Impelor housing

Roter casing

Roter

Delevery casing

Stuffing box bush

Shaft sleve

Water deflector

Cuplling half flexible

Baring cover

Grees cup

Flage section/ delivery

V) Bare Pump spare parts 21 to 50 HP Baring (Ball baring)

Rolar baring

Impelor key

Pump bush

Stud nut

Nut bolt kit

Air cock

Base plate

Water seal

Gland bush

Gland plate

Pump shaft

Latern Ring

Impelor brass

Impelor (C.I)

Difuser

Baring housing

Neck ring (small)

Neck ring (big)

Flasher

Foot volve

Check nut

Impelor housing

Roter casing

Roter

Delevery casing

Stuffing box bush

Shaft sleve

Water deflector

Cuplling half flexible

Baring cover

Grees cup

Flage section/ delivery

W) Bare Motor repairing Drive out bare motor

W) Bare Motor repairing Drive out bare motor i) 10 to 20 HP

W) Bare Motor repairing Drive out bare motor ii) 21 to 50 HP

Bare motor rewinding i) 1 to 5 HP

Bare motor rewinding ii) 6 to 10 HP

Bare motor rewinding iii) 11 to 15 HP

Bare motor rewinding iv) 16 to 20 HP

Bare motor rewindingv) 21 to 30 HP

Bare motor rewinding vi) 31 to 35 HP

Bare motor rewinding vii) 36 to 40 HP

Bare motor rewinding viii) 41 to 50 HP.

Motor opening, over oiling, fitting & testingi) 1 to 5 HP

Motor opening, over oiling, fitting & testing ii) 6 to 10 HP

Motor opening, over oiling, fitting & testing iii) 11 to 15 HP

Motor opening, over oiling, fitting & testing iv) 16 to 20 HP

Motor opening, over oiling, fitting & testing v) 21 to 30 HP

Motor opening, over oiling, fitting & testing vi) 31 to 35 HP

Motor opening, over oiling, fitting & testing vii) 36 to 40 HP

Motor opening, over oiling, fitting & testing viii) 41 to 50 HP.

Roter shaft turning & polishing i) 1 to 5 HP

Roter shaft turning & polishing ii) 6 to 10 HP

Roter shaft turning & polishing iii) 11 to 15 HP

Roter shaft turning & polishing iv) 16 to 20 HP

Roter shaft turning & polishing v) 21 to 30 HP

Roter shaft turning & polishing vi) 31 to 35 HP

Roter shaft turning & polishing vii) 36 to 40 HP

Roter shaft turning & polishing viii) 41 to 50 HP.

To make motor bush & housing (Baring sheet) i) 1 to 5 HP

To make motor bush & housing (Baring sheet) ii) 6 to 10 HP

To make motor bush & housing (Baring sheet) iii) 11 to 15 HP

To make motor bush & housing (Baring sheet) iv) 16 to 20 HP

To make motor bush & housing (Baring sheet) v) 21 to 30 HP

To make motor bush & housing (Baring sheet) vi) 31 to 35 HP

To make motor bush & housing (Baring sheet) vii) 36 to 40 HP

To make motor bush & housing (Baring sheet) viii) 41 to 50 HP.

To fit new motor i) 1 to 5 HP

To fit new motor ii) 6 to 10 HP

To fit new motor iii) 11 to 15 HP

To fit new motor iv) 16 to 20 HP

To fit new motor v) 21 to 30 HP

To fit new motor vi) 31 to 35 HP

To fit new motor vii) 36 to 40 HP

To fit new motor viii) 41 to 50 HP.

Panel board & Starter repairing i) 1 to 5 HP

Panel board & Starter repairing ii) 6 to 10 HP

Panel board & Starter repairing iii) 11 to 15 HP

Panel board & Starter repairing iv) 16 to 20 HP

Panel board & Starter repairing v) 21 to 30 HP

Panel board & Starter repairing vi) 31 to 35 HP

Panel board & Starter repairing vii) 36 to 40 HP

Panel board & Starter repairing viii) 41 to 50 HP.

To fit motor as it is i) 1 to 5 HP

To fit motor as it is ii) 6 to 10 HP

To fit motor as it is iii) 11 to 15 HP

To fit motor as it is iv) 16 to 20 HP

To fit motor as it is v) 21 to 30 HP

To fit motor as it is vi) 31 to 35 HP

To fit motor as it is vii) 36 to 40 HP

To fit motor as it is viii) 41 to 50 HP.

X) Bare Motor spare parts 10 to 15 : Bearing

Air fan

Shaft

Bearing plate

Motor bush

Roter assembly

Stud nut kit

Nut bolt kit

X) Bare Motor spare parts 6 to 20 : Bearing

Air fan

Shaft

Bearing plate

Motor bush

Roter assembly

Stud nut kit

Nut bolt kit

X) Bare Motor spare parts 21 to 50 : Bearing

Air fan

Shaft

Bearing plate

Motor bush

Roter assembly

Stud nut kit

Nut bolt kit

Y) Vaccume Pump Repairing Drive out pump i) 1 to 3 HP

Y) Vaccume Pump Repairing Drive out pump ii) 4 to 5 HP

Motor Rewinding i) 1 to 3 HP

Motor Rewinding ii) 4 to 5 HP

Pump opening, repairing, over oiling, fitting & testing i) 1 to 3 HP

Pump opening, repairing, over oiling, fitting & testing ii) 4 to 5 HP

Roter shaft turning & polishing i) 1 to 3 HP

Roter shaft turning & polishing ii) 4 to 5 HP

To make vaccume pump bush & baring housing i) 1 to 3 HP

To make vaccume pump bush & baring housing ii) 4 to 5 HP

To fit new pump set i) 1 to 3 HP

To fit new pump set ii) 4 to 5 HP

Panel board & starter repairing i) 1 to 3 HP

Panel board & starter repairing ii) 4 to 5 HP

Z) Vaccume Pump Spare Parts 1 to 3 HP : Baring

Impelor Key

Pump bush

Air fan

Sturnut key

Baring plate both side

Mechanical seal

Gland rope

Gland bush

Gland plate

Roter fitted shaft

Latern Ring

Roter G.M.

Fan cover

Spacer

Baring housing

Neck Ring

Port plate

Flage (delevery/ section)

Shaft sleve

Saction & delivery chember

Steter fitted motorbody

Tie rod

Roter casing

Liquid diflector

Z) Vaccume Pump Spare Parts 4 to 5 HP : Baring

Impelor Key

Pump bush

Air fan

Sturnut key

Baring plate both side

Mechanical seal

Gland rope

Gland bush

Gland plate

Roter fitted shaft

Latern Ring

Roter G.M.

Fan cover

Spacer

Baring housing

Neck Ring

Port plate

Flage (delevery/ section)

Shaft sleve

Saction & delivery chember

Steter fitted motorbody

Tie rod

Roter casing

Liquid diflector

Starter reley i) 6 to 10 A.

ii) 9 to 14 A.

iii) 13 to 21 A

iv) 19 to 27 A

Starter no volt & over load coil

Contactor set full i) S. K. -1

iii) M.L. -2

vii) M.L. - 6

viii) M.L. - 7

Reley plate (kit)

Contactor point kit i) S. K. -1

iii) M.L. -2

vii) M.L. - 6

viii) M.L. - 7

i) Fuse grip 16 A.

ii) Fuse grip 32 A.

iii) Fuse grip 63 A.

iv) Fuse grip 100 A

v) Fuse grip 200 A..

Fuse Base i) 16 A.

Connector Plate

i) Volt meter 0-440 Volt small

ii) Volt meter 0-440 Volt Big

Ampear meter

Ampear meter i) 0 to 15 A.

ii) 0 to 50 A.

iii) 0 to 100 A.

Capasitor 1 K.V.A.R.

Single Phasing Preventor

Water Level Guard with 60 M. wire

On-Off Rotery switch

Volt meter / Ampere meter switch

Nuon Indicator Lamp

Main Switch 440 Volt three phase

M.S.E.B. Unit i) 32 A.

H.R. C. Fuse i) 100 A.

Aquazilary Coil

Timer Coil

C.T. coil i) 60 A.

Tog Tester

Multi meter

Insulation Tester

Meger

Hand gloves - 1 pair (Rubber)

Insulated Rubber Matting

To Arthing with arthing 300 x 300 x 50 m.m. arthing plate, G I. pipe & arthing wire

To Arthing with arthing 450 x 450 x 50 m.m. arthing plate, G I. pipe & arthing wire

Arthing wire 14 to 6 guage

Starter D.O.L

i) 1 to 5 HP

ii) 5 to 10 HP

iii) Star Delta auto 10 to 20 HP

vi) Star Delta auto 21 to 30 HP

v) Auto transfarmer starter 20 to 30 HP

vi) Auto transfarmer starter 31 to 50 HP

Transfarmer coil rewinding with copper wire in transfarmer starter. without returning old copper wire.

Change over switch 50 A. 3 phase

Change over switch 100 A. 3 phase

Change over switch 200 A. 3 phase

Buz bar 30 to 50 HP

Transfarmer Oil

1) :- Providing, erecting and giving test of 100 mm dia. submersible pump sets confirming to IS 8034 and motor confirming IS 9283 : 1.5 HP

Submersible pump 150 mm dia (with bronze /Stainless (CF8M) impeller) up to 8 stages : 1.5 HP

Submersible pump 150 mm dia (with bronze /Stainless (CF8M) impeller) up to 12 stages : 8.0 HP

Submersible Monoblock (with bronze / stainless steel (CF8M) Impeller ) Horizontal/vertical -upto 3 stages: 3.0 HP

Supplying and erecting submersible pumpset suitable for 100 mm dia borewell fo reqused HP with, 230 v 50 cycles A.C. suitable for 10 to 50 LPM Discharge at 109 to 30 M a

Suppluing and erecting 3 core 2.5 sq. mm. insulated flat flexible submersible cable with Copper Conductor, PVC insulated and PVC sheathed

Suppluing and erecting 3 core 2.5 sq. mm. insulated flat flexible submersible cable with Copper Conductor, PVC insulated and PVC sheathed (MJP CSR (MECH) 15-16, Pg. No. 67, I.No.1-2)

Providing, suplying & in standard lenghts MDPE Pipes. Conforming to I.S.O. 4427:1996/with necessary jointing material like mechanical connection: 20 mm

Providing ISI mark GI pipe with one coupler of following class and dia including all local and central taxces, octroi, inspection charges, transportation to stores etc. complete. IS 1239/2004 : 15 mm dia Medium

20 mm dia Medium

25 mm dia Medium

32 mm dia Medium

40 mm dia Medium

50 mm dia Medium

65 mm dia Medium

80 mm dia Medium

100 mm dia Medium

125 mm dia Medium

150 mm dia Medium

Lowering, laying, jointing G.I. pipes and specials of following class and dia. including conveyance from stores to site of works, all labour, giving satisfctory hydraulic testing etc. complete. Either underground or in vertical position, as directed by Engineer-in-charge. :15 mm dia Medium

20 mm dia Medium

25 mm dia Medium

32 mm dia Medium

40 mm dia Medium

50 mm dia Medium

65 mm dia Medium

80 mm dia Medium

100 mm dia Medium

125 mm dia Medium

150 mm dia Medium

Providing, erecting C.I.D.F. reflux valve single door with jointing to pipe work(including all hardware and packing) water works quality with jointing to pipe without bypass arrangement with gunmetal seat excluding c.c. foundation/structural steel supports. For rating PN - 1.6 confirming to IS - 5312: 1984 :50 mm dia

65 mm dia

80 mm dia

Lowering, laying and jointing in position following CIDF Reflux valve/ Butterfly valve and Sluice valve including cast of all labour, jointing material including nut bolts and giving satisfactory hydraulic testing etc. complete.: 50 mm dia

65 mm dia

80 mm dia

Providing and supplying ISI standard C.I. flanged / S & S specials including all taxes (central and local) railway freight, insurance, unloading from railway wagon, loading into truck, transport to departmental stores/ site unloading stacking etc. complete. : 80 mm to 300 mm dia

Supplying and erecting triple pole iron clad/ metal clad switch and fuse 415/500 V. of suitable rating as below of approved make erected on angle iron frame

Suppluing and erecting set of 3 pilot lamps all bakelite with colour glasses with miniature lamps 230 V/250 erected on provided M.S. box with panel type fuses and connected with PVC wire.

Providing, erecting voltmeters A.C. 50 cycle/sec. with 0 to 500 V range flush type erected on provided M.S. Box and connected with necessary PVC wire.

Providing erecting ammeter A.C. 50 c/s 450 V of suitable range flush type complete erected in provided M.S.Box and connected to supply.

DOL STARTER- Supplying and erecting DOL starter to operate squirrel cage induction motor working on 380 - 400 V, 3 Ph., 50 Hz., with no volt coil, overload element with necessary material & connected to supply etc. comp. Starter with original sheet steel encloser.: Up to 7.5 HP

Up to 10 HP

F.A.S.D. STARTER- Supplying and erecting Fully Automatic Star delta starter to operate squirrel cage induction motor working on 380 - 400 V, 3 Ph., 50 Hz., with no volt coil, overload element and on off push button with necessary material & connected to supply etc. comp. : 7.5 HP to 12.5 H.P.

above 12.5 HP to 20 H.P.

above 20 HP to 25 H.P.

above 25 HP to 40 H.P.

Providing structural steel work in single stanctions composed of RSJ chanel etc. with caps, bases, mild steel plates angles, bracket cleats, gusset plates, anchour bolts etc. as per detailed drawing and design or as directed by Engineer-in-charge including cutting, fabricating, hoisting, erecting, fixing, in position making reveted/bolted/welded in connection and one coat of anti corrosive point and over it two coats of oil painting etc. complete.

Item No. 15 :- Earthing for pumping machinery Supplying and erecting galvanised cast iron earth plate 60 x 60 x 0.6 cm. burried in specifically prepared earth pit 1.5 mt. below groound level with 30 kg. charcoal and salt in alternate layers neccessary length of double G.I. earth wire 8SWC connected to plate with cadmium plate G.I. nut bolts 12 mm dia with bituminous compound and run through 12 mm dia. G.I. pipe.

Excavation for foundation / pipe trenches in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, normal dewatering, preparing the bed for foundation and excluding back filling, etc. complete. Lift 0-1.5 M.

Excavation for foundation / pipe trenches in Hard murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, normal dewatering, preparing the bed for foundation and excluding back filling, etc. complete.Lift 0-1.5 M.

Providing and supplying in standard lengths ISI mark rigid unplasticised PVC pipes suitable for potable water with unplastised PVC pipes suitable for potable water with solvent cement joints including cost of couplers, as per IS specification: 63 mm dia. PVC 4 Kg/ cm²

75 mm dia. PVC 4 Kg/ cm²

90 mm dia. PVC 4 Kg/ cm²

110 mm dia. PVC 4 Kg/ cm²

140 mm dia. PVC 4 Kg/ cm²

(MJP CSR 15-16, I.No. 1a, P.No. 72)

Lowering, laying and jointing PVC pipes and specials of following class and diameter including cost of conveyance from stores to site of work including cost of all labour, material, except cement solvent, rubber ring, giving satisfactory hydraulic testing as per IS code, etc. complete (with cement solvent joint / ring fit joint).: 63 mm dia. PVC 4 Kg/ cm²

75 mm dia. PVC 4 Kg/ cm²

90 mm dia. PVC 4 Kg/ cm²

110 mm dia. PVC 4 Kg/ cm²

140 mm dia. PVC 4 Kg/ cm²

Providing and laying in citu C.C. of of trap / granite/ quartzite/gneiss metal for foundation and bedding including normal dewatering, formwork, compacting and curing, finishing, etc.complete. PCC M -100

Providing and constructing two taps standpost as per type design with excavation 15 cm thick PCC (1:3:6) bedding 20 mm thick PCC (1:2:4) concrete for platform of 1.75 M dia. With side curb and bucket rest 80 mm dia, heavy duty GI pipe central post duly filled therein with C.C. (1:2:4) 5 M long, 20 mm dia. medium G.I. Pipe from point of tapping to standpost additional 20 mm dia G.I. pipe fixed verticaly upto 15 mm dia self closing water taps on brass ferrule etc. complete together with all labour and material charges as per drawing and as directed by Engineer-in-charge when good foundation is available. rate includes draining arrangement by excavating open gutters.

Refilling the trenches with available excavated stuff with soft material first over pipeline and then hard material in 15 cm layers with all leads and lifts including consolidation, surcharging, etc. complete.

Providing,hosting and fixing in position of approved make high density polyethylene UV stabilized conforming to IS 12701 ,water storage tank with necessary connections, testinfg etc complete 9 prior approval of sample by ex. Engineer is necessary before use ) Spect. No. as directed by engineer in charg. for 200 to 1000 Ltr

Providing,hosting and fixing in position of approved make high density polyethylene UV stabilized conforming to IS 12701 ,water storage tank with necessary connections, testinfg etc complete 9 prior approval of sample by ex. Engineer is necessary before use ) Spect. No. as directed by engineer in charg. for 1000 to 2000 Ltr

Providing fixing 15mm dia screw down bib stop tap of brass including necessory socket union nut complete

Providing and layingintrenches dia CPVC PIPE includieng necesary exavation fiting reffiling trenches etc complete including removing existing pipe line if the same in pwd chewky or as directed each complete for 15mm dia

Providing and layingintrenches dia CPVC PIPE includieng necesary exavation fiting reffiling trenches etc complete including removing existing pipe line if the same in pwd chewky or as directed each complete for 20mm dia

Providing and layingintrenches dia CPVC PIPE includieng necesary exavation fiting reffiling trenches etc complete including removing existing pipe line if the same in pwd chewky or as directed each complete for 25mm dia

Providing and layingintrenches dia CPVC PIPE includieng necesary exavation fiting reffiling trenches etc complete including removing existing pipe line if the same in pwd chewky or as directed each complete for 32mm dia

Providing and layingintrenches dia CPVC PIPE includieng necesary exavation fiting reffiling trenches etc complete including removing existing pipe line if the same in pwd chewky or as directed each complete for 40mm dia

Mahendra Rewinding and Electricals Works

Sakharkar Rewinding Works

OM SAI ELECTRICALS AND MACHINARY

ST Rewinding Works Gondia