ADDN / ALTN AND SPL REPAIRS TO MD ACCN BUILDING NO. P-84, P-88,P-115, P-125,P-217,P-218,P-220 AT AJAY BAUGH AND P-110, P-112, P-158 AND P-210 AT ASHWINI NAGAR UNDER GE MINNIEBAY, PORT BLAIR

Amount

Structural Rehabilitation Work

M&L for carrying out structural repairs for RCC members at all levels by removing loose and broken concrete by chiselling/mechanically etc upto a depth of 60 to 150 mm from the column, beam and similar structural members, cutting edges, cleaning the dismantled portion with wire brush etc to make the reinforcement naked and remove dust, dirt and other foreign particle etc and washing with high pressure clean water and removing rubbish off the premises to a distance n. exc upto 50 metres including necessary safety precautions and scaffolding upto a height of 15.00 mtrs complete all as specified and directed by Engineer-in-charge.

M&L for carrying out structural repairs for RCC members at all levels by removing loose and broken concrete by chiselling/mechanically etc upto a depth of 40 mm from the roof slab, column, beam and similar structural members, cutting edges, cleaning the dismantled portion with wire brush etc to make the reinforcement naked and remove dust, dirt and other foreign particle etc and washing with high pressure clean water and removing rubbish off the premises to a distance n. exc upto 50 metres including necessary safety precautions and scaffolding upto a height of 15.00 mtrs complete all as specified and directed by Engineer-in-charge.

M&L for applying rust remover and then applying Anti corrosive primer of makes mentioned in list of approved makes to all exposed reinforcement bars complete all specified and directed.

M&L TMT (CRS) Mild steel bars bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for handles etc and hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed by Engineer-in-charge.

Supply only for Hard drawn steel wire fabric weight not exceeding 4 kg per square metre, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia welding to existing reinforcement complete all as specified and as directed by Engineer- in- charge.

M&L for applying one coat of polymer bonding coat of approved make to bind old concrete surfaces of soffit of slab, coloumn, beam and similar structural members for new gunited / cement surface complete all as specified and directed by Engineer-in-charge.

M&L for applying first layer of bonding coat of aprroved make as specified and fix polymer cloth reinforcement of 200 gms per sqm on the top of wet coat and finally applying second layer of bonding coat complete all as specified and directed by Engineer-in-charge.

M & L for non-shrink, cementitious Micro concrete mixed with 12.5mm graded crushed stone aggregate in the ration as per manufacturer's instruction, as in sides and soffits of beams, jacketing of columns, roof slab and similar structural members including necessary form work leak proof for fair finished surfaces. The formwork shall be water tight to facilitate pouring of micro concrete complete all as specified and directed by Engineer-in-Charge.

Material & Labour for tying hard steel wire fabric 100mm x 100 mm x 10 gauge, binding with GI wire 22 gauge to reinforcement, applying cementitious slurry (mixture of cement, sand, water and polymer based additive) uniformly to exposed surfaces and guniting using CM 1:3 average thickness of guniting not less than 40mm and at a pressure not less than 6Kg/Sqm and finishing the surfaces with 10mm thick rendering in CM 1:4, troweled even & smooth finish, without using extra cement, area exceeding 1.0sqm in each patches including necessary scaffolding and necessary safety arrangements up to 4th floor complete all as specified and as directed by Engr-in-Charge. Note : Hard steel fabric used for guniting shall be measured and paid under separate item

M&L for cutting out existing cracks in concrete surfaces / masonry wall / RCC slab, forming a 'V' Groove of 25mmx40mm size, cleaning the groove thoroughly with air blower, priming the groove with mixture of Polymer based Resin & Hardener using spray gun/brush, filling the groove with putty of polymer based Resin, Hardener & admixture mixed in ratio as per manufacturer’s instructions, and finally applying a seal coat complete all as specified and directed by Engineer-in-Charge

M&L for applying polymer modified cement mortar rendering 15mm average thick in CM 1:3 on gunited /wall surface duly mixing polymer modifier complete finished even and smooth without using extra cement as per manufacturer's instructions complete all as specified and directed by Engineer-in-Charge.

M & L for applying curing compound of approved make as specified on newly polymer modifier cement mortar, Micro concreted, gunited surface for complete curing as per manufacturer's instruction complete all as specified and directed by Engineer-in-Charge.

M&L for drilling 15mm dia holes in to RCC slab / wall / Column /beams to a depth of 100 to 150mm & provide shear connector of 12mm dia rod of length of 150mm bent to "L" shape with 75mm to be embedded in hole & 75mm to be used as dowel, fixed with polyster resin grout mixed mechanically and pour the same into the hole and insert the shear connector and finish the top; allow the same to set complete all as per manufacturer's instructions and as directed. [Make of grout : 'Lokfix S' of make : M/s Fosroc chemicals India (P) Ltd. or equivalent in M/s Harjas Coatings & Polymers / M/s Pidlite Industries Ltd. / M/s Sika India Pvt Ltd / M/s Structural Water proofing Co Pvt Ltd / M/s BASF India Ltd].

Drilling of holes of size 10/12 mm dia to a depth of of 50 to 100 mm into concrete and cleaning the same with Air blower as directed

Note for Item No 1.01 to 1.14 :- 5% (Five) percentage of the total cost of the Sch-“A” items shall be retained as security deposit against Structural repair/rehabilitation works for a guarantee period of 5 years by submission of FDR in favour of GE from scheduled bank and completion of the entire work shall be issued only after the receipt of satisfactory structural test report from IIT/NIT or any Govt Institutions as approved by GE.

M&L for carrying out necessary NDT tests at the relevant locations in requisite numbers to assess the total structural strength of the existing(G+3/ G+2) storey building before and after the completion of the structural rehabilitation works through IIT/ NIT or any Govt inst duly approved by Accepting Officer complete all as specified and as directed by Engineer in charge. Note: Cost of transportation of equipments and expertise shall deemed to be included in this quoted item and Completion certificate of the entire work shall be issued by GE only after the receipt of satisfactory test reports of all buildings involved. .

Dismantling Plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings in roof covering all as specified and directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed by Enigneer-in-charge.

M&L for cutting holes into or through reinforced cement concrete slabs, chajjas, reinforced or otherwise exc 500 sq cm but n. exc 0.1 Sqm complete all as specified and directed by Engineer-in-charge.

S&F steel work in tubular roof trusses, trussed,purlins, rafters including special shaped washer etc using ERW or induction butt welded trusses conforming to I.S. 1161-1979 grade St.-240 complete all as specified and directed by Engineer-in-charge.

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-290.Gde-E-165 complete all as specified and as directed by Engineer-in-charge.

S&F mild steel Framed work such as grills, framed guard bars, ladders railings, frame of water tanks etc confirming to Fe-410 as specified and directed complete all as specified and directed by Engineer-in-charge.

S&F Plates (plain or chequered) channels, sqaure cut ir notched (ordinary and counter sunk) forming holes, without any attachment conforming to FE-410W (Grade E-250) quality A complete all as specified and directed.

S&F Mild steel screw bolts (machine made) 5 to 10mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5 cm but n exc 10 cm long complete all as specified and directed by Engineer-in-charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by Engineer-in-charge.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by Engineer-in-charge.

S&F aluminium flat as wind tie fixed with 40mm X 6mm aluminium self staging screws complete all as specified and directed by Engineer-in-charge.

Taking down existing roof treatment from roof and cleaning with wire brush to remove all loose particles and washing with water including removing the debris upto 100m distance complete all as specified and directed by Engineer-in-charge.

M & L for plain cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) in roof padding concrete, kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed by Engineer-in-charge.

M&L for plastering in CM 1:3, 10mm average thickness over the treated surface using water proofing compound as per manufacturer's direction including finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge. (Note :- Water Proofing compound will measured and paid seperately under relevant items)

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for foundation etc or for shafts, well cesspits, manholes, pier holes, laying of pipeline etc not exc 10 Sqm on plan and not exc 1.5 mtr in depth and getting out in soft/loose complete all as specified and directed by Engineer-in-charge.

Excavation over areas n. exc 1.5m deep and getting out as in soft/loose soil complete all as specified and directed by Engineer-in-charge.

M&L for use and waste of formwork in base of footings, base of column side and soffits of plinth beams of rough finished concrete surfaces complete all as specified and directed by Engineer-in-charge

M&L RCC M30 grade (Design Mix) using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams; bases for coloumns, etc basement slabs, under-reamed piles and mass concrete complete all as specified and as directed by Engineer in charge.

Returning, filling in including spreading levelling, watering and well ramming in layers not exceeding 25 cm thick as in soil complete all as specified and as directed by Engineer in charge.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5M above the starting point complete all as specified and as directed by Engineer in charge.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specially provided for complete all as specified and as directed by Engineer in charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) Finished fair all as specified and directed.

M&L RCC M-30 grade (Design Mix) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like complete all as specified and directed by Engineer-in-charge.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc complete all as specified and directed.

M&L for RCC M-30 grade (Design Mix) for columns, pillars,posts, struts, piers, columns and stanchions etc complete all as specified and directed by Engineer-in-charge.

Formwork to sides of chajjas, canopy, overhang, chullah hoods any projected parts of building and similar items including edges etc all as specified and directed by Engineer-in-charge.

M&L RCC M-30 as in chajjas and similar items etc all as specified.

Formwork to sides of beam , lintel beam ,lintel band , roof beam and similar work etc complete all as specified and directed by Engineer-in-charge.

M&L RCC M-30 as in beam , lintel , lintel band of any size and shape roof beam etc complete all as specified and directed by Engineer-in-charge.

Formwork to staircases with sloping or stepped soffits including risers and stringers (excluding landing)

M&L RCC M-30 as in stairways,balusters (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, landings and similar work complete all as specified and as directed

Demolition of Precast Concrete work/ precast concreteblock built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

M&L precast cement concrete block masonry with solid block, exc 10cm in width in PCC type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) all as specified and directed by Engineer-in-charge.

Providing precast cement concrete solid building blocks or slabs in PCC type C-1, 1:3:6 (using 20mm graded stone aggregate) n. exc 10cm thick and setting in cement mortar 1:4 complete all as specified and directed by Engineer-in-charge.

M&L AAC cement block masonry not exc 10 cm thick using approved make block grade I,having minimum compressive strength 40 kg/sqcm & density 551 to 650 Kg/Cum in cement mortar 1:4 mixed with non shrinking compound complete all as specified and as directed by Engineer-in-charge.

Taking down cement plaster on walls any description incl racking out joints hacking for key and scrubbing down with water etc. complete all as specified and directed by Engineer-in-charge.

M&L Rendering 10 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 (river sand)and finished fair and even without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15mm thick cement plaster on fair faces of concrete block masnory in two layers, base layer of 10mm thick in CM (1:6) and top layer of 5mm thick in CM 1:4(with river sand) mixed with WPC as per manufacture's instructions, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. Note :- WPC shall be measured and paid seperately

M&L rendering 5mm thick in CM (1:3) on ceiling surfaces finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Supply only water proofing compound

M&L for newly plastered surfaces, providing necessary scaffolding & safety precautions and cleaning the surfaces free from any loose paint, dust, greases, growth of fungus, algae or moss using wire brush and levelling the surface even smooth using mechanical sander and finally applying water by pressure jet washer of max pressure of 170 bar with automatic pressure relief system. The following process shall be initiated only after the above surface preparations :- (a) Filling the surface cracks using crack seal compound on required consistency using electric mixer. (b) Filling the dents and holes using wall care putty in appropriate ratio using electric mixer. (c) Applying one or two coats of damp proof primer (primer coat) using Airless spray technology with max working pressure of 22.8 Mpa/3300 psi and capable of operating single spray gun with a max material hose length of 30m.(d) Applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm Anti algal weather coat 100% acrylic smooth emulsion paint using Airless spray technology with max working pressure of 22.8 Mpa/3300 psi and capable of operating single spray gun with a max material hose length of 30m.

Note: (1) Work shall be executed only through authorised applicator duly approved by Manufacturer of Paint and certificate in this connection shall be submitted by the Contractor (ii) The affected area of the wall due to dampness shall be ascertained by moisture meter of power input 9v Display 60 LEDs using colour code scale and Moisture measurement of each location shall be submitted along with RAR. (iii) The contractor shall submit MOU letter with any one of Paint manufacturer within 28 days of receipt of acceptance copy failing which contract shall be liable for cancellation. Authorised applicator shall have valid authorisation letter from the manufacturer The authorisation letter needs to be valid for the complete period of execution of the painting work. Contd.../-

(iv) After preparation of the surface, Engr-in-Charge shall inspect and approve the same before applying primer and finishing coats. (v) Building wise stage passing register shall be maintained & submitted alongwith RAR/FB duly signed by Engr-in-Charge and contractor. (vi) The equipment to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. The specification and details of the equipment and tools pertaining to this item is denoted on Particular Specification.Manual method of paint application is not allowed and also Penalty shall be levied if appropriate tools & equipment pertaining to smart periodicals not used. Contd.../-

(viii) Proper masking arrangement shall be carried before the application of primer or paint. (ix) The other coat of Primer and Paint shall be applied only after the completion of drying time and comply with recoating period as per manufacturer instructions. (x) Cost of scaffolding shall be included in the quoted rate.

M&L preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer and 2mm thk wall care putty all as specified. (Wall care putty can be measured and paid separately)

M&L for preparation of newly plastered ceiling surfaces and applying two coats of oil bound distemper over a coat of primer over 1 mm thick wall care putty all as specified.

M&L for complete removal of existing treatment and treating with two coats of oil bound distemper over a coat of primer to wall surfaces incl preparation of old surface of wall all as directed by the Engineer-in-charge and as per manufacturers instructions

M&L applying 2 mm thick wall care putty over plastered surfaces wall/ ceiling to prepare the surface even and smooth

M&L for applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth.

M&L for complete removal of old existing treatment/ finishes providing necessary scaffolding & safety precautions and cleaning the surfaces free from any loose paint, dust, greases, growth of fungus, algae or moss using wire brush and leveling the surface even smooth using mechanical sander and finally applying water by pressure jet washer of max pressure of 170 bar with automatic pressure relief system. The following process shall be initiated only after the above surface preparations :-

(a) Filling the surface cracks using crack seal compound on required consistency using electric mixer. (b) Filling the dents and holes using wall care putty in appropriate ratio using electric mixer. (c) Applying one or two coats of damp proof primer (primer coat) using Airless spray technology with max working pressure of 22.8 Mpa/3300 psi and capable of operating single spray gun with a max material hose length of 30m. (d) Applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm Anti algal weather coat 100% acrylic smooth emulsion paint using Airless spray technology with max working pressure of 22.8 Mpa/3300 psi and capable of operating single spray gun with a max material hose length of 30m.

Note: (1) Work shall be executed only through authorised applicator duly approved by Manufacturer of Paint and certificate in this connection shall be submitted by the Contractor (ii) The affected area of the wall due to dampness shall be ascertained by moisture meter of power input 9v Display 60 LEDs using colour code scale and Moisture measurement of each location shall be submitted along with RAR. (iii) The contractor shall submit MOU letter with any one of Paint manufacturer within 28 days of receipt of acceptance copy failing which contract shall be liable for cancellation. Authorised applicator shall have valid authorisation letter from the manufacturer The authorisation letter needs to be valid for the complete period of execution of the painting work. Contd.../-

(iv) After preparation of the surface, Engr-in-Charge shall inspect and approve the same before applying primer and finishing coats. (v) Building wise stage passing register shall be maintained & submitted alongwith RAR/FB duly signed by Engr-in-Charge and contractor. (vi) The equipments to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. The specification and details of the equipments and tools pertaining to this item is denoted on Particular Specification.Manual method of paint application is not allowed and also Penalty shall be levied if appropriate tools & equipments pertaining to smart periodicals not used. Contd.../-

(viii) Proper masking arrangement shall be carried before the application of primer or paint (ix) The other coat of Primer and Paint shall be applied only after the completion of drying time and comply with recoating period as per manufacturer instructions. (x) Cost of scaffolding shall be included in the quoted rate.

M&L for applying one coat of OBD on ceiling including preparation of old plastered surfaces complete all as specified and directed.

M&L preparation of new wood/wood based surfaces of exc. 10cm width or girth of any description and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old painted wooden surface and applying one coat of synthetic enamel paint of any description exc 10 cm width or girth, complete all as specified and as directed.

M&L for preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparing old steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

Surface dressing n exc 15 cm deep in soft / loose soil complete all as specified and directed.

M&L for hard core of gauge n.exc 63mm, deposited , spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface broken stone complete all as specified and directed.

M&L for 100 mm thick PCC 1:3:6 type C-2 (40 mm graded aggregate), finishing cement concrete as in sub base all as specified and directed

M&L for 40 mm thick PCC 1:2:4 type B-0 (40 mm graded aggregate) as in floor all as specified and directed, finishing cement concrete as in floors finished even and smooth without using extra cement and spike rolling to surfaces or making impressions of expanded metal,whilst the concrete is green complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-1 (40 mm graded aggregate) plinth protection and similar work all as specified and directed, finishing cement concrete surface evan and smooth with using extra cement complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4 type B-2(40 mm graded aggregate) as in PCC path,hard standing and similar work all as specified and directed,finishing cement concrete surface even and smooth without using extra cement and Spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

M&L for Heavy duty chequered cement concrete tiles mixed with grey cement and no pigment of size 300x 300x25 mm thick set jointed and pointed in neat cement slurry in floors incl 20 mm thick screed in CM 1:4 complete all as specified and as directed by Engineer in charge

Demolition of cement concrete(unreinforced) of any description and in any position not otherwise specially provided for complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding and rubbished off the premises all as specified and directed.

M & L for 25 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in Sub base for flooring/levelling coarse, sunken floor etc complete all as specified and as directed.

M&L for coloured non-skid ceramic tiles 7 to 8 mm thick exc. 0.06 sqm but n.exc 0.11sqm area of each tiles in floor/ steps etc set and jointed in neat cement slurry and pointed in coloured cement to match as in floor over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed by Engineer-in-charge.

M&L for ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm in floor, over 15 mm thick screed bed in CM 1:6 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and directed by Engineer-in-charge.

M&L for ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in floor, over 15 mm thick screed bed in CM 1:6 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed.

M&L for ceramic coloured tiles in vertical surface (dado/skirting) to match the shade and size of floor tiles laid over and including 10mm thick back coat in CM (1:4),complete all as specified and directed.

M&L for glazed ceramic tiles 300 x 200x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick backing in cement mortar (1:3) all as specified and directed.

M&L for glazed ceramic tiles 350 x 250x 7mm / 450x300x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick backing in cement mortar (1:3) all as specified and directed.

M&Lfor virtified ceramic tiles 10mm thick (square/rectangular ) polished, area of each tile not exceeding 0.36 sqm in floors etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM( 1:4) complete all as specified and directed.

M&L for virtified ceramic tiles 10mm thick (square/rectangular ) polished, area of each tile exceeding 0.42 sqm but not exceeding 1 sqm,in floors etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM( 1:4) complete all as specified and directed.

M&L for virtified ceramic tiles 10mm thick light grade (square/rectangular) polished with size of tiles same as floor tiles in vertical surfaces such as skirting, dados and to steps etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including rendering 10mm thick plaster in CM (1:4) complete all as specified and directed.

Dismantling stone slab of any description or thickness in floors approns etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 20mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as directed by Engr in Charge.

M&L for 20mm Granite (of any type) work (table rubbed and polished) including necessary moulding on edges fixed on cup board shelves partitions holded on angle cleats , holdfasts ,rails including proper fixing arrangments with screws etc independently all as specified and as directed by Engineer-in-charge.

M&Lfor virtified ceramic tiles 10mm thick (square/ rectangular) polished heavy duty vertified tiles 300x300 size in floors, steps, raisers, etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed in CM (1:4) complete all as specified and directed.

Taking down 15mm Steel /16mm CPVC tubing and connections complete all as specified and as directed

Taking down 20mm Steel / CPVC tubing and connections complete all as specified and as directed

Taking down 25mm Steel / CPVC tubing and connections complete all as specified and as directed

Supply and fixing of CPVC pipes 20 mm dia outer bore SDR 11 &plain CPVC SDR 11 fittings on walls /ceilings or laying in floors including clamps etc complete all as specified.

Supply and fixing of CPVC pipes 25mm dia outer bore SDR 11 &plain CPVC SDR 11 fittings on walls /ceilings or laying in floors complete all as specified.

Refixing old steel tubing and connections of 15mm dia in new or old position (Walls, ceiling,floors, etc.) complete all as specified and directed by Engineer-in-charge.

Refixing old steel tubing and connections of 20mm dia in new or old position (Walls, ceiling,floors, etc.) complete all as specified and directed by Engineer-in-charge.

Refixing old steel tubing and connections of 25 or 32 mm dia in new or old position (Walls, ceiling,floors, etc.) complete all as specified and directed by Engineer-in-charge.

S&F 20 mm CPVC Brass Elbow complete all as specified and directed.

S&F 20 mm CPVC Brass Elbow reducer(3/4 x1/2) complete all as specified and directed.

S&F CPVC Male Brass Threaded Adaptor (MTA/MBTA) 20mm bore complete all as specified and directed.

S&F CPVC Male Brass Threaded Adaptor (MTA/MBTA) 25mm bore complete all as specified and directed.

S&F CPVC Female Brass Threaded Adaptor (FTA/FBTA) 20mm bore complete all as specified and directed.

S&F CPVC Female Brass Threaded Adaptor (FTA/FBTA) 25mm bore complete all as specified and directed.

Supply and fixing 20 mm outer dia CPVC Brass Tee complete all as specified and directed.

Supply and fixing 25 mm outer dia CPVC tank Adaptor complete all as specified and directed.

Supply and fixing 20mm outer dia CPVC union complete all as specified and directed.

Supply and fixing 20mm outer dia CPVC union complete all as specified and directed.

M&L for Cutting chases in concrete block walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan of size 'p' trap or 'S' Trap (pedestal pattern), with Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

S&F in repairs vitreous China squatting pan, `Orissa' pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in Repairs 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, and connections to pies an fixing of chain and pull, or lever, with PVC connections 20mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs brass chromium plated Hand shower (Health Faucet)(ABS Body) with 1 Meter long Easy Flex Tube in Chrome Finish& wall Hook complete all as specified and directed.

S&F in repairs ktichen sink made of stainless steel 1mm thick or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 x420 mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs ktichen sink made of stainless steel 1mm thick with drainage board or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915x460 mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, fixing in granite platform including neccesary fixing arrangement make good with white cement and suitable colour pigment overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs Towel Rail CP Brass Make Prayag Cat.No BA 10 S or equivalent complete all as specified and directed.

S&F in repairs Towel Rack 600mm Long with Lower Hangers Superior finished CP Brass complete all as specified and directed.

S&F in repairs brass chromium plated shower rose with or without swivel joint 100mm size complete all as specified and directed.

S&F in repairs Angular stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore complete all as specified and directed.

S&F in repairs two way bib tap cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore complete all as specified and directed.

S&F in repairs concealed stop cock with fitting sleeves,operating lever &adjustable wall flange with seal(compatible with ALD-089)valves cast copper alloy chromium plated with long shank and cup (concealed type) fancy type screwed down high pressure screwed both ends for pipe complete all as specified and directed.

S&F in repairs stop valves cast copper alloy chromium plated with long shank and cup (concealed type) fancy type screwed down high pressure screwed both ends for pipe or union fixed for 15mm bore,including necessary cutting and making good wall or floor tiling to match existing complete all as specified and directed. Note :- tiles to be paid under relevant items.

S&F in repairs Vitreous China wash basin, white, flat back, size 550 x400mm excluding ditto but including brackets with PVC connections 15mm/20mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 580x450mm excluding ditto but including brackets with PVC connections 15mm/20mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy chromium plated, fancy type, screwed down, high pressure with long screwed shanks and fly nut of 15/20mm bore complete all as specified and directed.

S&F in repair CP Toilet paper holder fancy type high quality complete all as specified and directed. (Make : ACN-1151N of Jaquar/T0254C of Johnson/272130160071 of Somany or equivalent as approved by GE)

S&F in repair Corner glass shelf high quality of 5mm thick glass ,12 cm wide & 60 cm long CP railing with bracket complete all as specified and directed.

S & F PVC Body Cabinet Box Mirror of size 350mm X 450mm X 100mm in PTMT alloy of approved design and pattern complete all as specified and directed

S&F in repairs bib tap cast copper alloy fancy type chromium plated screwed for 15mm bore of approved make complete all as specified and directed.

S&F Ball brass valve high pressure of polyethylene float and fly nut complete screwed for iron pipe and fixed, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed of 25mm bore complete all as specified and directed.

Dismantling PVC water storage tanks Exc 500 Ltrs capacity & nexc 1000 Ltrs and removing from site complete all as specified and as directed.

Disconnecting PVC existing tanks, Exc 500 & n.exc 1000Ltrs, setting aside (or lowering if required) for repairs,cleaning ,etc.and hoisting if required reconnecting and refixing in position and cleaning and removing scale and dirt,etc,from tanks and from mouths of circulating pipes etc complete all as specified and directed.

Supply and fix Rotational moulded polyethylene double layered ISI marked PVC water storage tank (cylindrical vertical with closed top) 1000 ltrs capacity hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

Supply and fix CPVC ball valve of 25 mm dia complete all as specified and as directed.

Demolition and breaking out drain pipes of dia up to 150 mm including necessary bend ,T and other accssories etc complete all as specified and directed by Engineer-in-charge.

S&F 110 mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls incuding necessary clamps and fittings etc to fixing on walls complete all as specified and directed.

S&F 110 mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints laid intrenches or in floors complete all as specified and directed.

S&F 75 mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints laid intrenches or in floors incuding necessary clamps complete all as specified and directed.

S&F 75 mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls incuding necessary clamps etc complete all as specified and directed.

S & F 110 mm bore UPVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore UPVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and directed..

S & F 110 mm bore UPVC (SWR) Vent Cowl complete all as specified and directed.

S & F 75 mm bore UPVC (SWR) bends of any radius complete all as specified and directed..

S & F 75 mm bore UPVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and directed.

S & F 110 mm bore UPVC (SWR) bends with access door complete all as specified and directed.

S&F 75 mm bore UPVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and directed.

S&F UPVC SWR reducers one end 110 another reduced 75mm complete all as specified and directed.

S&F UPVC in repairs (SWR) floor trap diameter of out let 110 mm ,plain with grating including jointing with solvent cement fixed in cement concrete all as specified and directed , Note:- cement concrete shall be measured and paid seperately under relevant items.

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc)or insulation boards /slabs /blankets any thickness including cover fillets, grid work any description and any position all as directed.

S & F Oral lay in plain aluminium ceiling system consisting of 600 x 600 mm ties of 0.6/0.7 mm thickness in white colour laid over pre-coated aluminium sections white colour 15mm wide Tee section flanges having stitching on the main runner, 1200mm and 600mm cross Tees with web height of 43mm and a load carrying capacity of 23.71 Kg/Sqm having galvanisation of 120gram/sqm, with ties having resistance (RH) of 100%, fire performances A2-S1, Do in module of size 600x600 with acoustic lining, suitable for green building applications, with re-cycled content of 50%,including PVC ceiling board/tiles, Moisture proof, light weight complete all as specified and directed by Engineer-in-Charge

M&L for preparing ceiling surfaces including rubbing with sand paper to obtain smooth surfaces and applying two coats of oil bound distemper over one coat of primer on ceiling complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm (with shutters & grill (if fixed) without taking off shutters from the frame) including iron mongeries all as specified and directed.

Taking down chowkats or frames exc 1.5 Sqm and not exceeding 4 Sqm (with shutters and grill (if fixed) without taking off shutters from the frame) including iron mongeries all as specified and directed.

Taking down chowkats or frames exc 1.5 Sqm and not exceeding 4 Sqm (with shutters and grill (if fixed) without taking off shutters from the frame) and refixing in same opening complete all as specified and directed.

Taking down Shutters of any description exc 2 sqm each and refixing in the same opening complete all as specified and directed.

Taking down Shutters of any description exc 1 but nexc 2 sqm each and refixing the same complete all as specified and directed.

All as per Item No 145 above but exc 2 sq. m each and removed from site complete all as specified and directed.

Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick with single side prelam PVC sheet used instead of plain colour PVC sheet and stile & rails having one side feathered edge and on other side 10 mm 90 degree bent edge consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stilesand plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stilesand plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S & F Anodised aluminium window and ventilator shutters, side hung type with or without sash bars, aluminium sections weighing 0.55 kg/m and thickness of section not less than 1.6 mm including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays, friction hinges 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and directed. Note: Labour cost for fixing of stainless steel friction hinges, glass, aluminium wire cloth and solar film shall be included under this quoted rate and material mentioned above shall be measured and paid separately under relevant items as Supply only. Rubber packing and aluminium handles, hinges shall not be considered for weighing and cost of the same shall deemed to be included in the quoted rate

S&F 15 micron coloured powder coated (minimum thickness) not less than 50 micron) aluminium anodized grill of design No.DG-202 ,10 mm thick ,cut to required size /shape ,and fixed in position with and including aluminium beading and frame complete all as specified and as directed by Engineer in Charge

S&F Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips,ruber neoprene packing,handles 2 Nos in each door ,hinges ,anodised aluminium snap beading screws complete all as specified and directed.

Fixing only in repairs anodised aluminium window and ventilator shutters, side hung type with or without sash bars, aluminium sections weighing 0.55 kg/m and thickness of section not less than 1.6 mm including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

Supply only Sheet glass, 4.8 mm ordinary quality and glazing with oil putty in square in exc 0.5 sq.m in each pane complete all as specified and directed.

Supply only for Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed.

Supply only 5.0 mm thick Figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane complete all as specified and directed.

Supply only aluminium anodized 'XPM' 1.50mm X 3.00mm size for mosquito proofing 22 gauge thick complete all as specified and as directed by Engineer-in-Charge.

Supply only Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed.

Supply only aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed.

S & F second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F 35 mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered complete all as specified and directed.

S& F 30 mm thick factory made Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and fixed to chowkats complete all as specified and directed.

S& F 30 mm thick factory made Flush shutters both sides covered with decorative face veneer with lipping/frame tp match , solid core construction, with particle board core and plywood face panels, commercial type on both sides and fixed to chowkats complete all as specified and directed.

S & F 30 mm thick factory made second class hard wood Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

Supply only stainless steel friction hinges of 100 mm size complete all as specified and directed.

S&F extruded aluminium alloy handles 125 mm long for Alu. windows/ ventilators complete all as specified and directed.

S&F butt hinges of stainless steel 100 mm long ISI marked fixed with brass screws complete all as specified and directed.

S&F in repairs butt hinges of stainless steel 100 mm long ISI marked fixed with brass screws complete all as specified and directed.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F extruded Brass barrel tower bolts,with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S&F 150 mm Extruded brass handles, fabricated type polished complete all as specified and directed.

S&F Floor door stopper of brass alloy body over all length of cover plate 150 mm and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

M&L 125mm Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F in repairs 125mm Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F in repairs 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 300mm long Brass ,sliding door bolt with sand or die cast brass hasp,staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

S & F 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 100 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs 100 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F Door closure hydraulically regulated designation No.3 universal type,suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F in repair stainless steel curtain rod of 20 mm dia complete all as specified and directed.

S&F Stainless steel brackets/holder and doom decorative diamond finish for fixing of 20 mmdia curtain rails complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Supply and fix bevelled edge mirror of size 600 mm wide of required height fixed to cup board shutter including 4mm thick commercial ply wood backing all as specified and directed.

Supply and fix mild steel flat iron as in hold fast and similar work complete all as specified and as directed.

M&L for PCC nominal mix (1:2:4) type B1 as in bed plates, kerbs, hold fast concrete etc. including formwork complete all as specified and as directed.

M&L 18 to 20 mm thick pre laminated MDF panels of interior grade type-II with melamine finish of approved shade for kitchen cabinet/wardrobe/wall paneling fixing with necessary fitting like keku fitting,spring clip,hanger plate,push fix or stud fitting and providing 0.9mm thick Decorative laminates type-I surface finish, colour and pattern as approved including all necessary cutting to the size and pasting to the wood surface with and including approved synthetic adhesive as per manufacturer's instructions complete all as specified and directed by Engineer-in-Charge.

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe410-0 or Fe 310-0 fixed in any postion including drilling and necessary screws, nails etc complete all as specified and directed.

S&F in repairs 30mm width continuous (piano) hinges mild steel ,bright finish or electro galvanised complete all as specified and directed.

S&f 100mm long aluminium anodised hasp and staples,safety type,with hinges including bolt to hingeplate and and fixed with screws complete all as specified and directed.

S & F Stainless Steel plate rack of size 600 mm X 580 mm of super deluxe model, suitable for 12 plates made with 22 gauge sheet and weight not less than 5.5 Kg, complete all as specified and as directed

S & F in repairs Stainless Steel plate rack of size 600 mm X 580 mm of super deluxe model, suitable for 12 plates made with 22 gauge sheet and weight not less than 5.5 Kg, complete all as specified and as directed.

M&L Providing, cement concrete Type C1 1:3:6 (20mm greaded aggregate) in plinth courses, roof kerbs of mud stops, rounded or chamfered on edges intels upto 1.5 m clear span, cills, steps; seismic and other similar bands,string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating complete all as specified and directed by Engineer-in-charge.

Supply and laying of CPVC pipes 40 mm dia outer boreSDR 11 &plain CPVC SDR 11 fittings on walls /ceilings or laying in floors as in spouts complete all as specified and directed by Engineer-in-charge.

S&F pulley operated clothes drying system of size 5 feet consisting of anodised aluminium pipes each of outer dia 22 mm and inner dia 19.8 mm , Pulleys made up of derlin with rope guide mounted on channel pair of length 24 inch (distance between two pipes is adjustable) ,locking system to hide rope knot .Channel to be mounted or fixed with self tapping screws provided in kit .Rope shall be polyester braided ,undyed of 4 mm dia complete all as specified and as directed.

S & F pulley operated clothes drying system of size 8 feet consisting of anodised aluminium pipes each of outer dia 22 mm, Pulleys made up of derlin with rope guide mounted on channel pair of length 24 inch (distance between two pipes is adjustable) ,locking system to hide rope knot .Channel to be mounted or fixed with self tapping screws provided in kit .Rope shall be polyester braided ,undyed of 4 mm dia complete all as specified and as directed.

M&L for 18 to 20mm thick prelaminated MDF ultra violet(UV) coated panels of interior grade type-II with melamine finish of approved shade for kitchen cabin/wardrobe/wall panelling fixing with necessary fitting like keku fitting,spring clip,hanger plate,modular hinge/clip,push fix or stud fitting as per manufacturers instructions complete all as specified and as directed. Make:M/s Action TESA/Kitply/Greenply/Centuary plywood or equivalent as approved protected shutters,HDF board in kitchen bottom cubboard shelf complete including removal of old cup board/ kitchen shelves any type. Note: Labour cost for fixing against item Nos: 205 to 213 shall be included under this quoted rate.

Supply only stainless steel Perforated cuttlery basket of 450 mm x 500mm size complete all as specified and directed.

Supply only stainless steel Plain Basket of 450 mm x 500mm size complete all as specified and directed.

Supply only stainless steel Perforated Thali plain basket of 450 mm x 500mm size complete all as specified and directed.

Supply only stainless steel 304 grade bottle basket pull out of 150 mm x 500mm size complete all as specified and directed.

Supply only stainless steel Bin Basket of 450 mm x 500mm x 500 mm size complete all as specified and directed.

Supply only stainless steel Designer basket of 450 mm x 500mm size for cabinet,drawers and shelves opening /closing operation Bin Basket of suitable size complete all as specified and directed.

Supply only stainless steel 304 grade soft close teleescopic channel 20" heavy duty of approved complete all as specified and directed.

Supply only stainless steel auto hinges of 304 grade approved make and of 100 mm size suitable for kitchen CB shutter/wardrobe etc complete all as specified and directed.

Supply only stainless steel handle of 150 mm size suitable for kitchen cabinet of approved make complete all as specified and directed.

Demolition of existing vitreous china squatting pan with integral foot rest including P or S trap along with unreinforced cement/lime concrete bed complete all as specified and as directed by Engineer in charge.

M&L for special treatment of sunken portion of combined toilet & bathroom of Offrs Md accn of area not exceeding 4 sqm as per following stages: Stage 1 :- Demolition of cement concrete coba etc and preparing the surfaces of existing sunken portion etc with wire brush to remove all loose dirt, oil grease etc. Stage 2:- Providing 10 mm thick plaster in CM 1:4 with chemical of Dr.Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Prime seal primer or STP Ltd(and allow to dry for 8 hours) under touch dry condition Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufacturer instruction. Contd..../-

Stage 5:-Again rendering 10mm thick in CM 1:4 mixed with Dr Fixit Pidicrete URP or plaster seal of STP Ltd. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP. Stage 7:- Making holes in wall and fixing 600mm long 20mm dia GI spout for draining the surplus water if any.

M&L for special treatment of sunken portion of WC of area not exceeding 2 sqm as per following stages: Stage 1:- Demolition of cement concrete and preparing the surfaces of existing sunken portion of bath etc with wire brush to remove all loose dirt, oil grease etc. Stage 2:- Providing 10 mm thick plaster in CM 1:4 with chemical of Dr.Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Prime seal primer or STP Ltd(and allow to dry for 8 hours) under touch dry condition Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufacturer instruction Contd..../-

Stage 5:-Again rendering 10mm thick in CM 1:4 mixed with Dr Fixit Pidicrete URP or plaster seal of STP Ltd. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP. Stage 7:- Making holes in wall and fixing 600mm long 20mm dia GI spout for draining the surplus water if any.

M&L for special treatment of sunken portion of bathroom area of size not exceeding 3 sqm as per following stages: Stage 1 :- Demolition of cement concrete and preparing the surfaces of existing sunken portion of bath etc with wire brush to remove all loose dirt, oil grease etc. Stage 2:- Providing 10 mm thick plaster in CM 1:4 with chemical of Dr.Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Primeseal primer or STP Ltd(and allow to dry for 8 hours) under touch dry condition Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufacturer instruction Stage 5:-Again rendering 10mm thick in CM 1:4 mixed with Dr Fixit Pidicrete URP or plaster seal of STP Ltd. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP. Stage 7:- Making holes in wall and fixing 600mm long 20mm dia GI spout for draining the surplus water if any.

Removal of concrete debris from the site and transporting and depositing outside the MD land of distance exceeding 4KM from the proposed site complete all as specified and as directed by Engineer in charge.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed by Engineer in Charge

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer in Charge

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same

M&L for taking down carefully existing aluminium /copper point wiring, (light, fan socket or power) unscrewing from board/outlet boxes, fitting and fixtures such as switches, sockets, ceiling rose,lamp holder, tube/ceiling fittings, bulk head fittings, tube lights and regulators etc and making good disturbed surfaces on walls, floors , ceilings etc complete all as specified and directed.

M&L for taking down unserviceable submain wiring alongwith batten/PVC/steel conduits etc and making good disturbed surfaces of walls/ floors to match the existing surfaces complete all as specified and directed.

M&L for taking down unserviceable main switches, DBs, and making good disturbed surfaces of walls/ floors to match the existing surfaces complete all as specified and directed.

M&L for taking down fan, sealing cable end, dismantling fan blades and removing fan and blades to be deposited to MES store complete all as specified and directed.

M&L for painting of ceiling fan complete, in situ with synthetic enamel paint by spraying including filling cavitites with filler, one coat after cleaning all dust etc complete all as specified and directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

M&L for point wiring with two core single PVC insulated and unsheathed 1100 volts grade cable multistranded copper conductor of size 1.5 Sqmm nominal area (FRLSH) drawn through and including non-metallic rigid PVC Conduit, medium duty not less than 20mm dia concealed in wall/fixed on walls/ceiling with GI saddles, GI screws, rawl plugs with all fittings including tees, junction boxes including one green colour 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable FRLSH grade as earth wire upto common earth and connected to earth dolly complete all as specified and directed. Note:- 1. All GI metal flush boxes and modular cover plate shall be measured and paid seperately. 2. Rates quoted shall be deemed to be include cutting chases for conduit and sunking for boxes, cutting and making holes in wall/floor passing in or through conduit and making good disturbed surfaces.

One light point controlled by one way switch.

One ceiling fan point controlled by one way switch and regulator.

One wall fan point controlled by one way switch.

One switch socket 5 pin 5 Amps flush type on independent board.

One switch socket 5 pin 5 Amps flush type on same board.

One exhaust fan point contolled by one switch

One light point controlled by two way switch.

One bell/buzzer point controlled by one push button

All as per Item No 228 here-in-before but with 2.5 Sqmm FRLSH cable for one socket 5 pin 15 Amps flush type/ Metal clad switch on independent board complete all as specified and directed.

M&L for point wiring with two core single PVC insulated and unsheathed 1100 volts grade cable multistranded copper conductor of size 1.5 Sqmm nominal area (FRLSH) drawn through and including PVC casing /caping medium duty not less than 20mm width mounted on walls/ceiling with GI screws, rawl plugs with all fittings including tees, junction boxes including one green colour 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable FRLSH grade as earth wire upto common earth and connected to earth dolly complete all as specified and directed. Note:- All GI metal flush boxes and modular cover plate shall be measured and paid seperately.

One light point controlled by one way switch.

One ceiling fan point controlled by one way switch and regulator.

One switch socket 5 pin 5 Amps flush type on independent board.

One switch socket 5 pin 5 Amps flush type on same board.

One exhaust fan point contolled by one switch

One bell / buzzer point contolled by one push button

All as per Item No 230 here-in-before but with 2.5 Sqmm FRLSH cable for one socket 5 pin 15 Amps flush type/ Metal clad switch on independent board complete all as specified and directed.

S&F modular switch one way, 6 Amps, 1 module, 240 volts complete all as specified and directed.

S&F modular switch one way, 16 Amps, 1 module, 240 volts complete all as specified and directed.

S&F modular switch two way, 6 Amps, 1 module, 240 volts complete all as specified and directed.

S&F modular bell push one way, 6 Amps, 1 module, 240 volts complete all as specified and directed.

S&F ceiling rose, 3 terminal polycarbonate isolated body complete all as specified and directed.

S&F bell multi music type complete all as specified and directed.

S&F modular socket 2/3 pins, 6 Amps, 2 module complete all as specified and directed.

S&F modular socket 2/3 pins, 16 Amps, 2 module complete all as specified and directed.

S&F step fan regulator, 120W- 2 module complete all as specified and directed.

S&F modular cover plate with frame 2/3 module complete all as specified and directed.

S&F modular cover plate with frame 4 module complete all as specified and directed.

S&F modular cover plate with frame 6 module complete all as specified and directed.

S&F modular cover plate with frame 8 module complete all as specified and directed.

S&F modular cover plate with frame 12 module complete all as specified and directed.

S&F modular metal flush box 2/3 module complete all as specified and directed.

S&F modular metal flush box 4 module complete all as specified and directed.

S&F modular metal flush box 6 module complete all as specified and directed.

S&F modular metal flush box 8 module complete all as specified and directed.

S&F modular metal flush box 12 module complete all as specified and directed.

S&F TV Co-axial modular socket 1 module complete all as specified and directed.

S&F telephone socket with shutters RJ11, 1 module complete all as specified and directed.

S&F rigid non-metallic PVC conduit of size 25mm boxes inclusive of junction/terminal, tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed.

S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

M&L for concealed submain wiring with PVC insulated unsheathed multi-stranded copper conductor cable four runs of 6 Sqmm single core (FRLSH) 1100 volts grade drawn through in and including non-metallic rigid PVC Conduit / PVC casing capping, medium duty not less than 25mm dia surface mounted in wall/fixed on wall/ceiling with GI saddles, GI screws, rawl plugs with all fittings and two runs of 6 Sqmm PVC insulated copper conductor (FRLS) for eart continuity wire complete all as specified and directed. Note:- Four runs of single core cable with two runs of earth continuity conductor and PVC Conduit / PVC casing capping, and its fittings will be measured as one length.

M&L for concealed submain wiring with PVC insulated unsheathed multi-stranded copper conductor cable two runs of 6 Sqmm single core (FRLSH) 1100 volts grade drawn through in and including non-metallic rigid PVC Conduit / PVC casing capping, medium duty not less than 25mm dia surface mounted in wall/fixed on wall/ceiling with GI saddles, GI screws, rawl plugs with all fittings and one run of 6 Sqmm PVC insulated copper conductor (FRLS) for eart continuity wire complete all as specified and directed. Note:- Two runs of single core cable with one run of earth continuity conductor and PVC Conduit / PVC casing capping, and its fittings will be measured as one length.

M&L for concealed submain wiring with PVC insulated unsheathed multi-stranded copper conductor cable two runs of 4 Sqmm single core (FRLSH) 1100 volts grade drawn through in and including non-metallic rigid PVC Conduit / PVC casing capping, medium duty not less than 25mm dia surface mounted in wall/fixed on wall/ceiling with GI saddles, GI screws, rawl plugs with all fittings and one run of 4 Sqmm PVC insulated copper conductor (FRLS) for eart continuity wire complete all as specified and directed. Note:- Two runs of single core cable with one run of earth continuity conductor and PVC Conduit / PVC casing capping, and its fittings will be measured as one length.

M&L for concealed submain wiring with PVC insulated unsheathed multi-stranded copper conductor cable two runs of 2.5 Sqmm single core (FRLSH) 1100 volts grade drawn through in and including non-metallic rigid PVC Conduit / PVC casing capping, medium duty not less than 25mm dia surface mounted in wall/fixed on wall/ceiling with GI saddles, GI screws, rawl plugs with all fittings and one run of 2.5 Sqmm PVC insulated copper conductor (FRLS) for eart continuity wire complete all as specified and directed. Note:- Two runs of single core cable with one run of earth continuity conductor and PVC Conduit / PVC casing capping, and its fittings will be measured as one length.

M&L for concealed submain wiring with PVC insulated unsheathed multi-stranded copper conductor cable two runs of 1.5 Sqmm single core (FRLSH) 1100 volts grade drawn through in and including non-metallic rigid PVC Conduit / PVC casing capping, medium duty not less than 25mm dia surface mounted in wall/fixed on wall/ceiling with GI saddles, GI screws, rawl plugs with all fittings and one run of 1.5 Sqmm PVC insulated copper conductor (FRLSH) for eart continuity wire complete all as specified and directed. Note:- Two runs of single core cable with one run of earth continuity conductor and PVC Conduit / PVC casing capping and its fittings will be measured as one length.

Supply & fixing ceiling fan 1200mm sweep with blades, down rods and connected accessories, 230 V, 1200 mm sweep. Min air delivery 210 CMM, 5 star rated, equipped with brushless direct current motor (BLDC) including provision of cable from ceiling rose/connector to fan complete all as specified and as directed.

Supply & fixing of exhaust fan metal body, AC, single phase 230 Volts, 300 mm sweep complete with shutter and louvers and exhaust fan shall be fixed with suitable size of buzzer bolt/hold fastner including making to the wall surface of nay type/girth and at any height for fixing of exhaust fan including making good disturbed surface with existing wall colour and provision of cable from ceiling rose/connector to fan complete all as specified and as directed Note: Old unservicable exhaust fan will be deposited to MES store yard

Supply & fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 HZ, RPM 1200, Copper winding of sweep 250mm and exhaust fan shall be fixed with suitable size of buzzer bolt/hold fastner including making hole to the wall surface of any type/girth and at any height for fixing of exhaust fan including making good disturbed surface with existing wall colour and provision of cable from ceiling rose/connector to fan complete all as specified and as directed. Note :- Old unserviceable exhaust fan will be deposited to MES store yard.

Supply & fixing LED lights fitting 1x 20W, 2000lm, CDL, surge protection of 2 KV, 4 feet 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make :- Philips/Crompton/Havells/Luker/Bajaj

Supply and fixing round LED surface downlighter 15 watt, 80lm/w, CDL for ceiling complete all as specified and as directed. Make :- Philips/Crompton/Havells/Luker/Bajaj

Supply & fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt, 1000lm, CDL, 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. Make :- Philips/Crompton/Havells/Luker/Bajaj

Supply and fixing LED Bulb 9 watt, B22 complete all as specified and as directed. Make :- Philips/Crompton/Havells/Luker/Bajaj

Supply and fixing LED oval shape single head wall mount light 20 Watt, bronze colour complete all as specified and as directed. Make :- Philips/Crompton/Havells/Luker/Bajaj

Supply & fixing Wall mounted fan 400mm sweep with blades, mounting accessories kit, blade guard set, guard ring, 5 star rated, AC 230V complete all as specified and as directed. Make :- Crompton/Havells/Bajaj/Orient

S&F in repair energy efficient new 15 liters capacity rated power 2 KW electrical geyser white/half white/Ivory, MS container inner tank with fiber reinforced body (FRB) puff insulation for both inner tank & for hot outlet copper connection pipe with all in built in safety accessories like thermostat/automatic thermal cut out with ON/OFF/CUT out indicators all pre-wired and additional safety accessories like pressure release valve/pressure reducing valve, non return valve, rate shall be including for new PVC heavy duty pipe with brass ferrule fitting for HOT and COLD water connections fixed in same or new location as directed/required as per manufacturers instruction with suitable size nuts & bolts, making necessary connection & testing on completion including taking down old unsv geyser and making good to the disturbed surface of wall complete all as directed. Make :- Havells/Bajaj/Racold/Usha

Supplying and laying on wall of CPVC pipes outer diameter 20mm SDR 13.5 pipes & plain CPVC SDR 11 fittings complete all as specified and as directed.

Supply and fixing Stop valves 20mm dia, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

Supply and fixing Bib tap standard 20 mm PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 20mm-125gms) complete all as specified and as directed.

Supply and fix RCBO of DX3, 2 pole , 25 Amp rating with sensitivity of 30 mA suitable for 240 Volts complete all as specified and as directed.

Supply & fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with provision for RCBO 2 pole complete all as specified and as directed.

M&L for sheet metal enclosure made up of 2 mm thick CRCA sheet suitable size for installation of 7 to 9 energy meter, dust/vermin proof, epoxy powder coated, siemens grey painting over a coat of red oxide primer inside/outside of the enclosure, double shuttered door with locking arrangements including taking down old unserviceable rusted sheet metal enclosure from the building complete all as specified and as directed. Note : The cost for concealing of sheet steel enclosure in wall and making good disturbed surfaces with existing wall colour shall be deemed to be included the quoted rate.

Supply and fixing as in repair of MCCB DB VTPN 8 way IP-54 made of sheet steel phos phatised, powder painted with 250 Amps copper bus bar for each phase, neutral link, earth bar and Din rail ,415 Volts with double door with MCCB incomer and MCB outgoing and fixing of cable with suitable size of lugs complete all as specified and as directed. Make :- Havells/L&T/Legrand Note : MCCB and MCB will measured and paid separately under relevant items

Supply and fixing as in repair of MCCB DB VTPN 4 way IP-54 made of sheet steel phos phatised, powder painted with 250 Amps copper bus bar for each phase, neutral link, earth bar and Din rail ,415 Volts with double door with MCCB incomer and MCB outgoing and fixing of cable with suitable size of lugs complete all as specified and as directed. Make :- Havells/L&T/Legrand Note : MCCB and MCB will measured and paid separately

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3½ core complete all as specified and as directed. Note: Excavation, returning filling and removing of excavated material will be measured and paid separately.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3½ core complete all as specified and as directed. Note: Excavation, returning filling and removing of excavated material will be measured and paid separately.

M&L for road cutting, removing of material, returning filling and PCC 1:2:4 for laying of LT UG cable/Galvanised iron pipe/Rex pipe complete all as specified and as directed.

S&F Double wall corrugated pipe of size 75mm including specials such as end caps, bends, tees and reducers complete all as specified and as directed.

Supply and fixing MCB SP 6-32 Amps ,10 KA, 'B' Curve, 230 Volts ,50 HZ complete all as specified and as directed.

Supply and fixing MCB SPN 6 to 32 Amps ,10 KA, C Curve, 230 Volts ,50 HZ complete all as specified and as directed.

Supply and fixing MCB SPN 40 to 63 Amps ,10 KA, C Curve, 230 Volts ,50 HZ complete all as specified and as directed.

Supply and fixing MCB TPN 40 to 63 Amps ,10 KA, C Curve, 415 Volts ,50 HZ complete all as specified and as directed.

Supply and fixing MCB TP 40 to 63 Amps ,10 KA, C Curve, 415 Volts ,50 HZ complete all as specified and as directed.

Supply & fixing MCB DB SPN 4 way, double door, sheet metal enclosure, 240V, 200 Amps rated busbar including fixing of cable with appropriate size of copper lugs complete all as specified and as directed. Note : Cost for concealed the DBs on wall including making good disturbed surfaces with existing colour shall be deemed to be included in the quoted rate.

Supply & fixing MCB DB SPN 8 way, double door, sheet metal enclosure, 240V, 200 Amps rated busbar including fixing of cable with appropriate size of copper lugs complete all as specified and as directed. Note : Cost for concealing the DBs on wall including making good disturbed surfaces with existing colour shall be deemed to be included in the quoted rate.

Supply & fixing MCB DB SPN 12 way, double door, sheet metal enclosure, 240V, 200 Amps rated busbar including fixing of cable with appropriate size of copper lugs complete all as specified and as directed. Note : Cost for concealing the DBs on wall including making good disturbed surfaces with existing colour shall be deemed to be included in the quoted rate.

Supply & fixing MCB DB TPN 4 way, double door, sheet metal enclosure, 415V, 200 amps rated busbar including fixing of cable with appropriate size of copper lugs complete all as specified and as directed. Note : Cost for concealing the DBs on wall including making good disturbed surfaces with existing colour shall be deemed to be included in the quoted rate.

Supply and fixing MCCB 4 Pole, 415V, Thermal magnetic type, 100 to 125 Amps with breaking capacity 16 KA complete all as specified and as directed.

Supply and fixing MCCB 4 Pole, 415V, Thermal magnetic type, 160 Amps with breaking capacity 25 KA complete all as specified and as directed.

Supply and fixing LED bldg security light fitting 24 watt 230V AC, Cool white, outdoor type with light sensor, pressure die cast housing with epoxy powder coated, dark graphite grey colour finish, poly carbonate cover with individual LED lenses with IP 65 protection including SPD 5KV complete all specified and as directed. Make:- Luker /Bajaj/Havells/Philips/Crompton

M&L for Fabricated mounting bracket for security light fitting made out of GI tubing 25mm dia light grade size 1.5m long, bend to shape including MS clamp/bracket made out of 32x6mm GI flat iron with necessary nut & bolts, washers complete all as specified and as directed.

Supply and fixing Polycarbonate cable junction box of size 93 x 93 x 62 mm with terminals totally shock proof, water proof, halogen free, silica and having thermally embedded gasket technology fixing on wall with two way 5 amp connector complete all as specified and as directed. Make:- Luker /Bajaj/Havells/Philips/Crompton/Hensel

M&L for taking down existing energy meter any type including all electrical connections and refixing at place as directed with appropriate size of lugs complete all as specified and directed.

M&L for earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised earth strip 32 x 6mm connected by means of bolts, nuts, check nuts and washer of galvanised iron or steel, provision of 40 mm dia GI pipe medium grade for protection of GI earth wire and 20mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) , type C1 chamber, MS funnel, wire gauge, 50 mm thick RCC 1:2:4, type B1 earth pit cover with 6 Nos, 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No 3 of schedule Part-I. Note: (i) Cost of GI earth wire and GI protection pipe upto 7.5mtr length shall be deemed to be included in the rate quoted for this item (ii) The unit rate shall also includes for Wire mesh, funnel, excavation, PCC chamber pit, test point complete

Kakolil Trade Agencies

S G Enterprises

SACKSON ENTERPRISES

M/s V M K Construction

P NAIDU

Hindustan Traders

A.G.Construction

M/S ISLAND REALCON INDIA PVT. LTD