Spl repair to works in bldg No T-03 (Single Offrs Accn) and Constr of Envt ponds under AGE B/R-II at Tibri Mil Stn Gurdaspur.

Amount

Roughing the surface of old concrete floor picking sweeping cleaning and washing down with water to remove dust/mud etc and brushing neat cement slurry @ 3kg/Sqm all as specified.

M&L for cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in roof padding averaging thickness of 50mm complete all as specified.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) including bitumen primer @ 0.40 kg /Sqm laid on applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed and all as per manufacturer's instructions.

M&L for preparation of newly or previously untreated surface of any description wood, steel, iron, concrete,brick, stone, etc,exceeding 10cm in width or girth and applying two coats aluminium paint over one coat of priming paints plaster coat complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges incl demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15cm thickness (below or above ground level) complete all as specified and as directed.complete all as specified and directed.

M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.06 sqm but n. exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match the surface including 15 mm thick screed bed in cm 1:6 incl dismantling floor hearth or wall tilling including cement mortar bedding removing rubbish off the premises complete all as specified and as directed.

M&L for ceramic glazed dark shed coloured tiles of size 450x350x7mm thick joint free on and incl 10mm thick screed bede in CM (1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of well as in skirting/dado incl dismantling floor hearth or wall tilling including cement mortar bedding removing rubbish off the premises complete all as specified and as directed.

M&L for vitrified ceramic tiles, light shade 10mm thick (Square/ rectangular) polished, area of each tiles not exceeding 0.36sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete incl dismantling CM bedding, removing rubbish off the premises all as specified and directed.

All as per Srl item No 08 above but on vertical surface over 10 mm thick backing plaster in CM 1:4 incl dismantling of tiles and CM bedding complete all as specified and directed.

S&F 12mm thick perforated particle board/tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with nails to frame work or with staples on snap grid complete all as specified and as directed.

S&F for anodised aluminium snap grid 600mm x 600mm frame work incl hangers 6 mm dia. GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified for false ceiling complete all as specified and directed.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats) complete all as specified as directed.

All as per Srl item No 12 above but exc 1.50sqm but n.exc 4.00 Sqm.

S&F Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F powder coated anodised aluminium door shutters, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door, hinges, anodised aluminium snap beading screws etc incl sheet glass 5.5 mm thick ordinary quality complete all as specified and directed.

S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long, hinges type B-21, 100mm long (2 no.) suitable handle incl sheet glass 4mm thick ordinary quality complete all as specified and directed.

S&F aluminium anodised grill, 3 to 5mm thick made in diamond shape mesh of size 65 x 65mm complete as specified and directed.

S&F aluminium body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and as directed.

M&L for decorative laminated type 1 of thickness 1.5 mm surface finish(Sunmica), colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions on existing cupboard shutters including 18 mm thick plywood grade BWR, type BB complete all as specified and as directed.

S&F aluminium alloyed handle cast type anodized of size 100mm long all as specified and directed.

S&F butt hinges med weight cold rolled mild steel 100mm size all as specified and directed.

S&F 150 mm hasp and staple, safety type,brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed.

Taking up and down GI pipe15mm bore including fittings, connection all as specified.

All as per Srl item No 23 above but 20mm bore of pipe.

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked all as specified and directed.

All as per Srl item No 25 above but fixing only (old serviceable pipe re-used).

S&F GI tubing 20mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings ISI marked all as specified and directed.

All as per Srl item No 27 above but fixing only (old serviceable pipe re-used)

S&F vitreous China wash down water closet pan one piece EWC (pedestal sigle pattern), with smooth action plastic seat cover,valveless symphonic action type flushing cistern fixing as per manufacturing instruction complete as specified and directed.

S&F CP brass health faucet (hand shower) including flexible pipe of required length fixing to 15m dia pipe with brass check nut complete all as specifed and directed.

S&F in repair vitreous china wash basin, white, flat back, size 550x400mm (excluding taps, chain, plug and porcelain stopper) but including brackets, CP waste coupling 32mm bore, PVC waste pipe and cutting for pinning ends of brackets complete all as specified and directed

S&F in repair brass CP centre hole basin mixture 15 mm bore complete all as specified and directed.

S&F in repair PVC waste pipe 32mm bore fixed to WHB as per existing length complete all as specified and directed.

S&F in repair brass CP wall mixer with telephonic shower arrangement and telephonic shower suitable for 15mm dia bore pipe.

S&F in repairs bib tap, 15mm dia, CP, short body, screwed, high pressure for iron pipe complete all as specified and directed.

S&F in repair PVC connection, 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair stop valves, 15mm bore, fancy type, chromium plated with long shank and cup, (concealed type) screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed all as specified and directed

S&F in repair angle valves, 15mm bore, chromium plated, fancy type, screwed down, high pressure, screwed on both ends, fixed with iron pipe etc complete all as specified

S&F in repair PVC mirror cabinet, size 350x450mm with shelves of best quality including fixing arrangements, complete all as specified and directed.

S&F in repair glass shelve assembly 60cm in oval shape consisting of 8mm to 10mm thick glass including CP guard railing with double rail complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type , 60 cm long between flanges complete all as specified and directed.

S&F in repair MS pipe, 25mm bore, powder coated, chromium plated with fixing brackets stops rollers including fancy type knobs two Nos to each curtain rod complete all as specified and directed.

S&F 110mm bore PVC (SWR) ISI marks pipes single socketed in any length with rubber ring joints fixed to wall or floor incl dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required all as specified & directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls or floor incl dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required complete all as specified.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR ) bends 110 mm bore any radius all as specified.

S&F PVC (SWR ) bends 75 mm bore any radius all as specified.

S&F stack clamps (100 mm pipe) out of 50x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base for receiving the floor finishes complete all as specified.

M&L for 15mm thick rendering in cm 1:6 on brick or concrete surfaces fair finished the surfaces even and smooth without using extra cement including taking down all as specified and directed.

All as per Srl item No 50 above but 05mm thick on ceiling in CM 1:3.

M&L for 20mm thick rendering on fair faces in CM 1:4 on brick or concrete surfaces other than fair surface, finished the surfaces even and smooth without using extra cement including taking down of cement plaster complete all as specified & directed

M&L for rendering in patches n.exc 3.0 Sqm in each patch including taking down of cement plaster on walls /concrete surfaces etc and rendering 15mm thick cement plastering in cm 1:6 on brick or concrete surfaces fair finished the surfaces even and smooth without using extra cement Complete all as specified & directed.

M&L for rendering in patches n.exc 3.0 Sqm in each patch including taking down of cement plaster on walls /concrete surfaces etc and rendering 20mm thick cement plastering in cm 1:4 on brick or concrete surfaces other than fair finished the surfaces even and smooth without using extra cement but with using water proofing compound including taking down of cement plaster Complete all as specified & directed. (Note : WPC shall be measured and paid separately.

M&L for preparation of new plaster surface and finishing walls with acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper (of approved shade) on walls over primer chalk whiting on plastered surfaces complete all as specified.

M&L for applying two coats of oil bound distemper (of approved shade) on walls over primer chalk whiting on old plastered surfaces incl complete removal of existing treatment complete all as specified.

M&L for complete removal of existing treatment and finishing walls with acrylic smooth exterior paint of required shade : New work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) all as specified and directed.

M&L for preparation of old painted steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for excavating over area in any type of soil, exc 1.5m but n.exc 3.0m deep and getting out complete all as specified and directed.

M&L for surface dressing in hard dense soil n.exc 15cm deep complete all as specified and directed.

M&L for hard core of brick gauge n. exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and in post hole complete all as directed and Engineer-in-Charge.

M&L for PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in foundation, filling and post hole complete all as directed and Engineer-in-Charge.

M&L for excavating in trenches in any type of soil, n. exc 1.5m wide n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 Sqm on plan and getting out all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:4) on fair faces of brick work or concrete surface making it even and smooth without using extra cement complete all as specified and as directed.

M&L for brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:4 brick slightly rounded as wedged shaped complete all as specified and directed.

M&L for flush pointing in CM 1:3 to brick laid of floors complete all as specified and directed.

Supply only integral water proofing compound.

Excavating in post holes in hard dense soil (or similar holes) each n.exc 0.5m cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and post hole complete all as directed and Engineer-in-Charge.

S&F hand rails, half round or other steel section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars for doors, balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts complete all as specified and directed.

M&L for excavating over areas in any type of soil exc 1.5 m depth but n. exc 3.0m deep and getting out complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams ans soffits (if any) of foundation and plinth beams and similar work vertical or to batter all as specified and directed.

S&F mild steel TMT bars 10mm dia and over cut to length, bent to shape as required, including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips complete all as specified.

M&L for RCC (M-25) desigin mix in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns etc basement slabs, under reamed piles and mass concrete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in bedding and haunching against the pipe complete all as specified and as directed by Engineer-in-Charge.

Removing excavated material exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point.

Returning, filling including spreading and well ramming in layers not exc 25 cm thick in soft loose soil all as specified and directed.

M&L for RCC drain pipes NP3, 450mm bore including laying pipes to level or to falls in trenches, on concrete bed and all necessary extra joints, waste and cutting as jointed complete with collars as specified and directed.

E/M PORTION Taking down carefully aluminium/ copper point wiring for light, fan, bell, socket of point complete fiitings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc complete all as specified and directed.

M&L for point wiring with PVC insulated and PVC unsheathed multistranded FRLSH copper conductor cable of size 1.5 Sqmm including existing concealed PVC conduit fittings and making good to the disturbed surfaces with continuous earth wire of copper 1.5 Sqmm dia to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing to CI/MS boxes for mounting of accessories like surfaces sockets and regulators etc. complete all as specified for One light / Fan/ bell point controlled by one way switch complete all as specified and directed.

All as per Srl item No 83 above but one 5 amp socket outlet on independent board.

All as per Srl item No 83 above but one 5 pin socket outlet 5 amp on same board.

All as per serial item No.83 here-in-before but wiring with 2.5 sqmm FRLSH copper wire including earth wire 2.5 Sqmm of copper for 15 Amps 3 pin socket outlet.

M&L for sub main wiring with two runs of single core multi stranded PVC insulated, copper conductor, grade 1100 Volt, FRLSH cable of size 6 sqmm (red for phase and black for neutral) including PVC conduits not less than 1.2 mm thick and 25mm dia and 6 sqmm multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete including taking down old unserviceable wiring complete all as specified and directed. Note :- (a) Cost of making good the disturbed surface plastering/ filling putty alongwith matching with the existing surface is deemed to be included in the quoted rate by contractor. (b) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 5 amps complete all as specified and directed.

S&F socket outlet 3 pin 5 amps flush type complete all as specified and directed.

S&F switch flush type 15 amps single pole type one way complete all as specified and directed.

S&F socket outlet 3 pin 15 amps flush type complete all as specified and directed.

S&F in replacement of LED tube light fitting wall mounted with single side connection polycarbonate LED batten with aluminium housing and integrated electronic driver of capacity 20W, four feet and connection with PVC insulated twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed.

S&F wall /ceiling mounting LED 9/10 watt tube light fitting complete with all acessories 1x9 Watt LED , with CCT of 6000k suitable for domestic application, 240 Volts, 50 Hz, and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete all as specified and directed.

S&F decorative 9W, LED wall mounting fittings complete set including 9W LED lamp 9 Watt polycarbonate type B-22 complete all as specifed and directed.

S&F PVC insulated sheathed copper wire 1.5 sqmm FRLSH single core 1100 volt for inverter connection in same conduit all as specified and directed

S&F fan regulator electronic type 5 step 100 watts, 240 volt and connecting complete all as specified and directed.

S&F bell, AC, 230 volts, single pole complete all as specified and directed.

S&F bell push flush type 6 Amp complete all as specified and directed.

S&F lamp holder, PVC/ polycarbonate type insulated body with back plate suitable for batten / angle fittings complete all as specified and directed.

S&F ceiling rose, surface bakelite 65x50mm three terminal all as specified and directed.

S&F in replacement GI pipe bracket made out of GI pipe light grade 32 mm bore and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 32mm thick with nuts, bolts and washers complete including dismentling the existing GI pipe bracket and drilling of holes for nuts and bolts etc complete all as specified and directed.

S&F LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F in repair sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 8 way with 200 amps rated bus bar SPN double door complete all as specified and directed. (Note :- All the connection of incoming and out going wire in MCB will be made with thimble with suitable size as directed).

S&F in repair MCB single pole 6 amps to 32 amps, complete all as specified and directed.

All as per Srl item No 104 here-in-before but single pole and neutral 32 amps complete all as specified and directed.

M&L for replacement of distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way MS sheet including fixing to wall, cutting chases, grounting and necessary patch work and white wash to match with the existing including making connections all as directed containing the folowings:- (a) MCCB 4 pole 63 amps 16 KA breaking capacity with thermal release: 01 No (In coming). (b) Bus bar made out of aluminium duly insulated wire adhesive tape RYB & black :4 Nos. (c) MCB SPN 40 Amp- 4 Nos, MCB SP 40 Amp- 04 Nos (out going). (d) Connection from MCCB to bus bar will be made with aluminium strip of suitable size as directed. (Note :- All the connection of incoming and out going wire in MCCB and MCB will be made with thimble with suitable size as directed).

M&L for earthing complete with galvanised steel earth plate electrode 60cm ×60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C-1, pre-cast RCC (1:2:4) MS bar funnel & wire mesh, excavation and earth work in any type of soil including dismantling existing earthing complete all as specified & directed by Engr-in-charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete al as specified and directed.

Supply and lay brick common burnt sub class "B" old size for protection of cable laid in trenches for under ground cable all as specified.

M&L for sand cushioning in trenches using fine sand to under ground cable, laid in two layers 15cm before laying the cable and 8cm after laying the cable complete all as specified.

M&L for GI tubing light grade fixed along the pole/under road/along the wall of size 40 mm bore with necessary clamps all as directed.

A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit Rs. 23,780 from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

M/S G P MARWAHA (BID ID -3496180)

KAILASH CONSTRUCTION CO (BID ID -3504426)

M/S RUDHRAKSH TRADING CO (BID ID -3498742)

M/S RAJESH SHARMA & CO. (BID ID -3498737)

KULBHUSHAN AGGARWAL (BID ID -3498750)

SUBASH MAHAJAN (BID ID -3496817)

M/S SUDERSHAN KUMAR CHOPRA GOVT CONTRACTORS (BID ID -3498781)