SPECIAL REPAIR TO OMQs T 26 AND T 09 AT AFAC COIMBATORE

Amount

Dismantling of asbestos cement (Corrugated, semicororrugated , etc) sheets in roof covering including ridge complete all as specified and directed.

Dismantling of timber scantling in rails, posts, rafters, purline, etc. under 40 sq. cm in section (unframed) complete all as specified and directed.

Demolition of brickwork or stone boulder masonary , built in cement mortar complete all as specified and directed.

Dismantling ceiling boards ( fible, pulp, insulation etc.) or insulation boaeds/slabs/blankets, any thicknees, including cover fillets complete all as specified and directed.

Demolition of reinforced cement concrete in ground floors and pavings n. exc 15 cm thick complete all as specified and directed.

Demolition of concrete in ground floors and pavings n. exc 15 cm thick complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) to stone and rubbish off the premises complete all as specified and directed.

Taking down cement plaster on brick or stone walls, ceilings, etc including racking out Joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L brickwork with fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L brickwork with fly ash bricks straight or curved on plan exc 6m mean radius half brick thick walls, built in CM 1:4 complete all as specified and directed.

M&L reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in slab supported on walls deck slab and in shelves etc complete all as specified and directed.

TMT steel bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for slab, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slab, landing and similar work not exc. 200mm thick complete all as specified and directed.

S&F rolled mild steel Fe 410-W (Grade E-250 quality A) as in roof trusses, purlines, crane grantries, rails and fasteningd and heavy brackets framing (Beam, tee, angle, channel or flat section) including distance pieces etc.complete all as specified and directed.

S&F rolled mild steel Fe 410-W (Grade E-250 quality A) as in framed work as in doors or gates of angle or other section with gusset plates, rails, brackets etc, complete, drilled for fixing of steel sheeting or other covering, Doors, etc. to be prepared for hanging or sliding with and including either hooks door fittings (including rails and guides) and hanging also fastering and fixing complete all as specified and directed.

S&F Mild steel plain black sheet 1.00mm thick in steel gates and similar work, cut to size, holes punched, including rounded headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc complete all as specified and directed.

S&F steel work in tubular section as in staging including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161 - 1979 grade St 240 complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screw complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof ridge, rain gutter etc. fixed with self tapping screw complete all as specified and directed.

Supply and fixing of non asbestos fibre cement building boards, 6mm thick (lake and hill design) laid/inserted to existing timber/ steel,GI/aluminum framework in repairs all as specified and as directed.

Supply and fix anodised aluminium snap grid of size 605mm x 605mm frame work for false ceiling all as specified and as directed.

Providing and fixing Gypsum Board 9mm thick in ceiling fixed with screw as per manufacturers instructions all as specified and directed.

Supply and fix Armstrong mineral fibre acoustical suspended ceiling system with 600x600x16mm classic lite (Bevelled Tegular) edge tiles with Armstrong 15mm exposed grid. The tile laid on Armstrong superfine 38 with 15mm wide 'T' section flanges colour white having rotary stiching on all section ie. the main runner 1200mm & 600mm cross tees with a web height of 38mm and load carrying of 12.5Kg/sqm and pull out strength of 100 Kgs. The T section have a Galvanising of 90 gm/sqm and need to be installed with suspension system of Armstrong make.Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200x600 mm module. Cut cross tee longer than 600mm require independent support. 600x600 mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Permeter trim shall be Armstrong wall angles of size 3000x24x24mm, secured to walls at 450mm maximum centres. Anchor fasteners with verticle Hangers made out of galvanised steel of size 26x26x1.2mm with a galvanised thickness of 80 gms, pre-straightened hanger wire of dia 2.5mm and length of 1.8m, thickness of 80gms, and a tensile strength of 344-413 MPG alongwith adjestable hook clips or 0.8mm thich galvanised spring steel for 2.68mm with a minimum pull strength of 110 kg. The adjestable clip also consists of a 3.5mm Quiline wire to be used with main runner complete all as specified and directed. Make : Armstrong.

M&L for Cement concrete 1:2:4 type B-1 using 20mm graded aggregate, 40mm thick for sub base of floors complete all as specified and directed.

M&L for Screed bed or bedding layer of mortor 15 mm thick in CM 1:6 for laying floor finishes all as specified and directed.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces with CM 1:4 as in backing coat of skirting /dado all as specified and directed.

M & L for vetrified light shade ceramic tiles 10mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by Engr-in-charge..

M & L for vetrified dark shade ceramic tiles 10mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by Engr-in-charge..

All as per item No 28 above but as in skirting/dado.

M & L for Non-skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by Engr-in-charge..

M & L Glazed coloured ceramic tiles in vertical surface 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by Engr-in-charge..

M & L for chequered cement concrete coloured designer tiles 30cmx30cmx25mm thick, set and jointed in neat cement slurry and pointed with white cement and pigments in floor to match the surface all as specified and as directed by Engr-in-charge..

M&L for Cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate in steps, coping water troughs and the like including weathering, slightly angles and throating all as specified and directed.

M&L 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection in alternative bay and surface finish even and smooth with out using extra cement including necessary form work complete all specified and directed.

M&L for Rendering in CM 1:6, 15 mm thick on fair faces of brick work or concrete surfaces all as specified and directed.

M&L for Rendering in CM 1:4, 15 mm thick on other than fair faces of brick work or concrete surfaces all as specified and directed.

M & L prepation of newly plastered wall surfaces and applying two coats of distemper oil emulsion over over a coat of primer over 2 to 3mm wall care putty all as specified and as directed directed by Engr-in-charge.

M & L for complete removal existing treatment of wall surfaces and applying two coats of distemper oil emulsion over a coat of primer over 2 to 3 mm wall care putty all as specified and as directed directed by Engr-in-charge.

M & L prepation of new plastered wall surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and as directed directed by Engr-in-charge.

M & L prepation of old wall surfaces and applying two coats of cement base paint complete all as specified and as directed directed by Engr-in-charge.

Preparation old surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed..

Preparation of new surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying one coat of pinkl primer and two coat cf synthetic enamel paint.

Preparation of new surface of steel and steel based material of any description not otherwise described over 10cm width or girth applying one coat of red oxide zinc chrome and two coat synthetic enamel paint complete all as specified and directed.

Preparation old surface of steel and steel based material of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed..

Taking down chowkhats or frames with shutter (with out taking off the shutters from the frames) size exc 1.50 sqm and not exc 4.00 sqm each and all as specified and directed.

Taking down chowkhats or frames with shutter (with out taking off the shutters from the frames) size not exc 1.50 sqm each and all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm but not exc. 2 Sqm each all as specified and directed.

S & F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suplying and fixing in opening as per specification and drawing etc complete all as specified and as directed by Engineer- in-Charge.

S & F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tube for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour PVC sheet for top rial, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement , suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed by Engineer-in-Charge.

S&F plain solid straight chowkhats with IInd class hardwood and frames wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed

Material and labour for 35 mm thick plain , framed panelled shutters with IInd class Hard wood (two panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veeneering on both faces. The size of rail and stile as per IS 1003 (Part I), kiln seasoned and chemically pressure treated and fitted to chowkahts all as specified and as directed by Engineer-in-Charge.

Material and labour for 35 mm thick Glazed and skeleton shutter, open rebated and prepared to receive glass , gauge, etc with sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.24 (a) and fitted to chowkats complete all as specified and as directed by Engineer-in-Charge.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel and all as specified and directed

S & F Floor door stopper 140mm long with cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apperture 1.40 mm and fixed with stainless steel wire staples all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of apperture 1.40 mm and fixed with stainless steel wore staples all as specified and directed.

S&F 150mm long Aluminium anodised barrel towers bolts of extruded section and all as specified and directed

S&F 125mm long Extruded aluminium alloy handles, fabricated type, anodised butt hinges, heavy weight, cold rolled mild steel and all as specified and directed

S&F in repairs Door closer hydraulically regulated designation No. 3 universal type Aluminium (Die cast) body, suitable for door shutters of 851 to 1000mm in width and of weight between 60 to 80 kg and fixed complete and all as specified and directed

S&F 300mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy complete and all as specified and directed

S & F 30mm dia fancy type curtain rails aluminium anodised chromium plated with fixing brackets, stops, rollers etc.including taking down existing curtain rod/ palmate box of any description and any position etc all as specified and directed.

M & L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with gray cement slurry and pointed with white cement withadmixture of pigment to match the shade of granite stone including 15mm thick screed bed or bedding layer of in CM 1:6 all as specified and as directed.

M & L for 18/19mm thick prelaminated particle board , exterior grade , prelaminated both side with decorative choice laminarion and fixed with screw to frame etc complete all as specified and as diirected.

S&F Continous (piano) hinges 30mm width mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F 100 mm long hasp and staple, aluminium anodised, including bolt to hinge plate and fixed with screw complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore complete all as specified and directed.

S&F 15mm bore steel tube medium grade galvanised, with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore steel tube medium grade galvanised, with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S& F in repair Vitreous China wash basin, white, flat back, size 630x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specifed and directed.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white including seat cover and flush pipe etc complete all as per specified and as directed by Engineer-in-Charge.

M & L for PVC (SWR) multi floor trap of 75mm dia with grating including jointing with solvent cement etc complete all as per specified and as directed.

M & L for PVC (SWR) gully trap of 125/110mm dia includingsetting jointing with solvent cement etc complete all as per specified and as directed.

S & F PVC (SWR) pipe 110mm dia single sockted in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) bends 110mm radius complete all as specified and directed.

S & F in repairs PVC valveless, syphonic action type, flushing cistern of 10 Ltrs capacity , low level , white, with inlet , ball valve, float and handle including brackets and flush pipe etc complete all as specified and as direted by Engineer-in-Charge.

S & F PVC connections 15 mm size with PTMT nuts of length 450 mm all as specified and as directed.

S & F in repairs towel rail 60cm long of brass chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190 gms) all as specified and as directed.

S&F in repairs Bib taps, brass chromium plated fancy type with cruch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore all as specified and as directed.

S&F in repairs chromium plated angle valves, cast copper alloy, screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipes or for unions and fixed. 15 mm size all as specified and as directed.

S&F in repairs pillar taps fancy type cast copper alloy, with capstain head, chromium plated screwed down high pressure, with long shanks and fly nuts screwed for iron pipe and fixed 15 mm bore all as specified and as directed.

S&F in repairs 125mm dia shower rose brass chromium plated with or without seivel joints, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs chromium plated 15mm bore wall mixture Hot and cold two in one with L bend for connect to shower screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipes or for unions and fixed. 15 mm size all as specified and as directed.

S&F in repairs brass chromium plated health faucet with hand held and spring operated control valve with PVC flexible pipe connection of suitable length as directed fixed to 15 mm bore pipe all as specified and as directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen with plugs, waqshers and wastes, including bedding in cement mortar on to dward wall or including fixing cantilever brackets and connection union to pipe, overall size 915X460mm bowl size 410mmX330mmX160mm complete all as specified and directed.

Dismantling of PVC water tank 500 ltr capacity and removing to store all as specified and as directed.

S&F moulded polyethylene 500 ltr water tank storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engr-in-charge.

S&F moulded polyethylene 1000 ltr water tank storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engr-in-charge.

S&F in repairs 20 mm Ball brass valves, high pressure, with polythene float and flynut cimplete screwed for iron pipe or brass ferrule and fixed in repairs complete all as specified and directed.

S&F in repairs 15mm bore Gun-metal , globe or gate valve, with iron wheel head, screwed both ends for iron pipe fixed complete all as specified and directed.

S&F in repairs 20mm bore Gun-metal , globe or gate valve, with iron wheel head, screwed both ends for iron pipe fixed complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated brackets guard and raling 60 cm long complete all as specified and directed

S& F Glass corner shelf of size 30x30 cm with heavy wall brackets and fixed to wall s complete all as specified and directed.

S & F in repair stainless steel wall mounted plate rack of size 900x750x260mm of approved make complete all as specified and directed.Make : M/s Blue Star , Model No: BSKPR-311 or other equvalent make as approved by Engr -In-Charge

S&F sheet glass, ordinary quality 5.5mm thick and glazing with aluminum beading or gasket in square/rectangular exc 0.5sqm in each panes complete all as specified.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staple complete all as specified and directed.

M&L framed work such as grills ,grating etc with ends of bars shouldered or riveted, or forged into spikes conforming to Fe 290-Gde -E-165 all as specified and as directed.

M&L at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall using chemical emulsion at the rate of 2.25 liters per linear meter including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L for treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and directed.

Note for item Nos. 99 to 101 :- Make shall be Chloropyriphos/ Imidacloprid 3.5 %.

Removal of debries /building material out side the campus including loading and unloading , etc to a distance exc 5.00 Km but n. exc 10.00 Km out side the MoD land all as specified. Note: Location and premission of depositing the building materials/disposal out side the M of D land shall rest with contractor at his own arrangement.

S&F Anodised aluminiam frame powder coating for sliding doors , Partition Wall,window,ventilators with one or more rebeats including joining clear for fixing etc.completed all as specified.

S&F Anodised aluminium powder coating window and ventilator shutters, side hung type without sash aluminium section weighing 0.55 kg/m incl necessary joining cleats, glazing clips rubber packing anodised aluminium snap beading screws anodised fittings such as peg stays 150 mm long( (1 Nos ) , hinges type B-21 100 mm long(2 Nos) suitable handle (01 Nos) etc complete all as specified and as directed

Taking down old unserviceable point wiring (light, fan socket or power) complete, including fixture and fittings such as switches,ceiling rose, pendents, regulators,sockets, light fittings etc.removing materials for keeping for taking credit( credit for above items should be made as per conditions separately) and making good the isturbed surface of walls floors etc. all as specified and as directed

Taking down old unserviceable submain wiring of any size including GI/copper earth continuity conductor in PVC conduit on wall/roof and making good to disturbed surfaces all as specified and as directed

Taking down Ceiling fan sealing cable end, dismantling blades from fan and keeping in safe custody for reuse at site and making good the disturbed surfaces complete all as specified and as directed.

Refixing only Ceiling fan with and including carrying out cleaning servicing, oiling and greasing of fans and connecting up including provision of cable from celling rose/ connector to fan all as specified and as directed.

M& L painting of Ceiling fan complete, in situ with synthetic enamal paint by spraying incl filling cavities with filler, one coat after cleaning all dust etc all as specified and as directed.

Disconnecting electric connection and taking down main switch/DB of any size and keep in safe custody for taking credit complete and making good/levelling the disturbed surfaces of wall to match with existing surface all as specified and as directed

M&L for concealed Point wiring complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed for one light point controlled by one, one way switch.

Ditto all as per item No 111 but one ceiling/exhaust fan point controlled by one, one way switch.

Ditto all as per item No 111 but one switch socket outlet point 5 Amps on independent board.

Ditto all as per item No 111 but one switch socket outlet point 5 Amps on same board.

Ditto all as per item No 111 but one call bell point controlled by one push button on the same board

Ditto all as per item No 111 described here-in-before but with copper conductor cable FRLS, 2.5 Sqmm for one 3 pin socket outlet, 15 Amps and including 2.5 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board.

Note for item Nos. 111 to 116 : Cutting chases and making good in wall / floor will be Measured and paid seperately.

Supply & fix TARA-M/10W , LED tube light fitting with LED 1x10W MS white powder coated decorative LED T8 batten with PC tube complete all as specified and directed. Make: Havells Cat No. ENDURALINEARNEOBS10WLED830SPCWH or C&S Cat No. LTDC01210WLED/WD or equivalent in Luker

S&F lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings including LED Lamp complete all as specified and directed.

Supply & fix surface mounting LED light fitting 4ft, 1x18 watt decorative box type with driver, holder and including 1x18 watt 4 ft retrofit PC/glass tube complete with making connection by using twin core flexible twisted copper wire from ceiling rose to light fitting complete all as specified and directed.

Supply and fix building security light 20 Watt, new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening separate driver compartment with IP65 protection and impact resistance of IK07 complete with and including GI bracket made of suitable size medeium grade GI pipe bent to shape and fixed complete all as specified and directed. Make: Luker LST 60 or Equivelent in Havells, Crompton

Disconnecting carefully electric energy meter single phase and keeping aside , and re-fixing the same after necessary wiring work complete all as specified and directed.

Disconnecting carefully old unserviceable distribution boards any sizes including MCBs complete and making good the disturbed surface of wall all as specified and directed.

Supply and fix sheet metal enclosure with distribution board (DB) TPN, 415 volts, having IP:43 protection, isolated neutral bar, insulated busbar assembly, door earthing arrangement, mechanical impact strength IK08, 04 way compact double door suitable for fixing MCBs TPN as in commer and out going complete all as specified and directed. Make: Indoasian, Havells, Standard

Supply and fix MCB DB, SPN, 8 ways, Isolated neutral bar with double door IP54 protection, door earthing arrangement with cement spill protector, mechanical impact strength IK09 complete all as specified and directed. Make: Indoasian, Havells, Standard

Supply and fix MCB TPN 63 Amps, 240Volts, 10 KA, "C" Curve complete all as specified and directed. Make: Indoasian, Cat No. 811220 or Havells Cat No. DHMGCTNF063, or equivalent in Standard.

Supply and fix MCB SPN 40 Amps, 240Volts, 10 KA, "C" Curve complete all as specified and directed. Make: Indoasian Cat No. 811152 or Havells Cat No. DHMGCSNF040, or equivelent inStandard

Supply and fix MCB SP 6 to 32 Amps, 240Volts, 10 KA, "C" Curve complete all as specified and directed. Make: Indoasian, Havells, Standard

Supply and fix ceiling rose surface type bakelite 65 x 50mm with three terminals all as specified and directed.

S&F Modular fan regulator step type 120 W, 2 module complete all as specified and as directed.

S&F Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed.

S&F Switch Modular 16A single pole, one way, 1 module complete all as specified and as directed.

S&F Socket, 6A - 2/3 pin combined 2 module including back plate complete all as specified and as directed.

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed.

S&F Modular bell push 6A single pole, one way, 1 module complete all as specified and as directed.

Supply and fix Buzzer, Ding Dong, AC 230 volts complete all as specified and directed.

M&L for concealed Sub main wiring by making recess in wall/surface complete with 2 runs of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories suface/concealed in wall/Ceiling etc for three phase sockets all as specified and as directed by engr - in- charge. Note :- 2 runs of 6 sqmm, + 1 run of 6 sqmm (Earth Cotinuity conductor) and 1 run of PVC conduit shall be measured as one unit length.

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 M below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , earth lead GI wire 4mm dia ( 8 SWG) connectd to GI earth plate elcectrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth wire connected to main switch board/ feedar pillar and protected by galvanised iron pipe medium grade 15mm bore and 20mm bore medium grade GI pipe with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete 1:2:4 type B-1 & RCC cover and all as shown in Electrical Plate No. 3 of SSR ( Part-I) of 2009. (i) The unit rate includes earthing wire, and protection pipe upto 7.5 metre.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth all as specified and directed.

Supply and fix Single pole and neutral enclosure with a two pin and earth plug abd socket complete with one Double pole MCB 20 Amps complet all as specified and directed.

Supply & fix LED mirror light helios 11 watt complete all as specified and directed. Make: Luker Cat No. LMR9 or equivelent

Excavation in trenches not exceeding 1.5 m wide and n.exc. 1.5 m deep and getting out in hard/dense soil for laying of UG cables or for errection of pole complete all as specified and directed.

Disconnecting electric connections of old LT UG cable and taking out from the trenches complete, 16/ 10 sqmm by removing old brikcs and stacking in a safe custody for re-using serviceable bricks complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing excavated materials (soils) to a distance not exc 50m and depositing where directed at a level not exc. 1.5 m above the starting point all as specified and directed.

M/L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, multi stranded, 1100 volts grade, cross-sectional area 25 Sqmm, 4 core with and including making connection by using necessary thimbles complete all as specified and directed.

Material and labour for clean and dry sand (unwashed) in trenches and cable ducts including spreading and levelling for cushioning of underground cables all as specified and directed.

Supply and laid well burnt bricks sub-class 'B' designation 75 for cable protection, brick shall be laid dry flat as width of brick eqals to the length of cable and the gap between two adjacent brick shall not exceeded 10 mm, complete all as specified and as directed.

VIJAYA ENTERPRISES