PROVN OF BATHROOM FOR XXXX AT RANGAPAHAR MILITARY STATION

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation over areas not exceeding 1.50 m in depth and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and not exceeding 1.5m deep Soft / Loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and exceeding 1.5m deep and not exceeding 3.0m deep in Soft / Loose soil complete all as specified and as directed.

Material and labour treating the backfill in contact with foundation at the rate of 7.5 litres of ATT chemical emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

Material and labour treating the top surface of filled earth at the rate of 5 litres of ATT chemical emulsion per square metre of surface complete all as specified and directed.

Material and labour treating the soil under plinth protection at the rate of 5 litres of ATT chemical emulsion per square metre of surface area complete all as specified and directed.

Material and labour for cement concrete 1:2:4 type B-2 (using 40mm graded aggregate) as in foundations filling and mass concrete complete all as specified and directed.

Supply & Fixing Reinforcement using TMT steel bars 500D, 10mm dia and over, cut to length,bent to shape required,including cranking bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips qualsecuring with clips all as specified and directed.

Supply & Fixing Reinforcement using TMT Bars 500D of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

Supply & Fixing Reinforcement using TMT steel bars 500D of 5mm dia and over upto includig 10mm dia in stirrups spacers and binders complete all as specified and directed.

Material and labour for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter with rough finished surfaces of concrete, flat complete all as specified and as directed.

Material and labour for use and waste of form work to sides of pillars, posts, struts, piers, piers, columns and stanchions of square, rectangular or polygonal shape with rough finished surfaces of concrete complete all as specified and as directed.

Material and labour for use and waste of form work to soffits of suspended slab such as roof slabs, floor slabs, landing and similar work, etc. not exceeding 200mm thick with rough finished surfaces of concrete flat complete all as specified and as directed.

Material and labour for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc with rough finished surfaces of concrete flat complete all as specified and as directed.

Material and labour for use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide with rough finished surfaces of concrete complete all as specified and as directed.

Material and labour for formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed.

Material and labour for reinforced cement concrete (design mix) in M-30 (20mm graded aggregates) for foundation and plinth beams etc complete all as specified and as directed. Note :- Note :-(i) Reinforcement and form work required shall be measured and paid seperately (ii) Design mix will be approved by the GE.

Material and labour for Reinforced cement concrete (design mix) in M-30, (20 mm graded aggregate) in columns/pillars complete all as specified and as directed. Note :- (i) Reinforcement and form work required shall be measured and paid seperately (ii) Design mix will be approved by the GE.

Material and labour for reinforced cement concrete (design mix) in M-30 (20mm graded aggregate) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed. Note :- (i) Reinforcement and form work required shall be measured and paid seperately (ii) Design mix will be approved by the GE.

Material and labour for reinforced cement concrete (design mix) in M-30 (20mm graded aggregates) for beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. Note :- (i) Reinforcement and form work required shall be measured and paid seperately (ii) Design mix will be approved by the GE.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Chajjas and the like complete all as specified and as directed. Note :- (i) Reinforcement and form work required shall be measured and paid seperately (ii) Design mix will be approved by the GE.

Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Materials and labour for half brick thick brick work with sub class 'B' bricks straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and as directed.

Material and labour for Providing 40mm thick PCC 1:2:4 type B-0 as in Damp Proof course to horizontal or vertical surfaces including necessary form work etc complete all as specified and asdirected.

Material & Labour for rendering 15mm thick in cement mortar 1:4 including mixing with liquid water proofing compound @ 200 ml per bag of cement on brick masonry surface even and smooth without using extra cement complete all as specified and as directed. Note: Liquid water proofing compound will be measured and paid separately.

Material & Labour for cleaning plastered surfaces to receive the water proofing membrane and rendering of 15 mm thick screed bed or bedding layer in CM 1:4 mixed with liquid water proofing compound @ 200 ml per bag of cement on concrete roof surface, finished the surface fair and even to maintain the proper slope of roof surface, applying one coat of hot paving bitumen of penetration value 85/25 conforming to IS 73 @ 1.20 kg/sqm over a coat of bitumenous primer @ 0.30 ltrs per sqm and applying a layers of APP based polymeric membrane, 3mm thick (minimum) weight 3.00 Kg/sqm reinforced with polyster non woven fabric (weighing not less than 150 gms/sqm) shall be applied over Bitumenious primer (Application of polymeric memberane shall be by torch application, over laps shall be minimum 100mm on the transverse direction & 75 mm on the longtudinal direction) polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by membrane flashing, coved fillet in PCC (1:2:4) type B-0 of radius 75 mm shall be provided at the junction of roof & other vertical surfaces & surfaces shall be painted with hot paving bitumen of penetration value 85/25 conforming to IS 73 @ 1.20 kg/sqm & applying one coat of aluminium paint over the APP nmodified membrane @ 0.11 kg/sqm complete all as specified and as directed. Note: (i) Liquid WPC shall be measured and paid seperately.

Material and labour for rendering 10 mm thick in CM 1:6 on fair faces of Brick masonry/Concrete surface finished even and smooth without using extra cement all as specified and directed.

Material and labour for rendering 5mm thick in CM 1:3 in ceiling on fair faces of brick work or concrete surfaces, finished even and smooth without using extra surfaces complete all as specified and asdirected.

Supply only Liquid water proofing compound complete all as specified and as directed.

Material and labour Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

Material and labour broken stone or boulders hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed.

Material and labour for 75mm thick cement concrete 1:4:8 type D2 (40mm graded aggreded) as in sub base, finish the surface even and rough to receive topping layer complete all as specified and as directed.

Material and labour for 25mm thick cement concrete 1:2:4 type B1 (20mm graded aggreded) as on top surfaces finish even and smooth without using extra cement complete all as specified and as directed.

Material & Labour for machine cut kota stone slab as in riser of steps, skirting, dado etc. using 18 to 20mm thick slabs laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including borders, margins in two or more shades of slabs over and including rendering of 10mm thick in cement mortar 1:3 complete all as specified and as directed.

Material & Labour for joint free non skid ceramic coloured tiles 7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding .06 sqm but not exc 0.11sqm in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match including screed bed of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

Material & Labour for joint free glazed ceramic coloured tiles 450 x 300 x 7 mm thick of premium quality on skirting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over and including rendering of 10mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

Supply and fixing for 18-20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, window cills, cooking platforms and like etc and fixed over and including 10mm thick cement plaster in cement mortar (1:3) and pointing with white cement mixed with pigment to match the shade of granite (1:2) using marble dust complete all as specified and as directed.

Material & Labour for 75mm thick, PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc surface finished even and smooth without using extra cement and providing necessary joints 12mm wide to the full depth of PCC at every 3 meters and every change of directions and the joints duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade any penetration and 3 parts of sand [all by weight] complete all as specified and as directed.

Material and labour for preparing newly plastered ceiling surfaces and applying three coats of white washing complete all as specified and as directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whitening primer complete all as specified and as directed.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of Exterior Weather proof Paint over a coat of exterior primer complete all as specified and as directed.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

Supply and fixing framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Supply and fixing Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening complete all as specified and as directed.

Supply and fixing Factory made solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement fixing in frame at site as per specification complete all as specified and as directed.

Supply and fixing 100 mm size, medium weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed.

Supply and fixing aluminium anodized bow handles 150mm long extruded, cast type complete all as specified and directed.

Supply and fixing Aluminium anodised barrel tower bolt of extruded section and fixed 200 mm long complete all as specified and as directed.

Supply and fixing 250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts,of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Mild Steel work flat iron conforming to Fe - 290, Grade E-165 as in hold fast complete all as specified and as directed.

Returning, filling in including spreading and levelling watering and well remming in layeres n.exc. 25cm thick complete all as specified and directed.

Removal of excavated material [Soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Supply and fixing Vitreous China Wash Down Water Closet [Pedestal pattern] of minimum size 520x360x390mm, Ivory colour including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap including making good the disturbed floor complete all as specified and as directed.

Suppy & fixing Vitreous China Ware Wash Hand Basin, counter sunk type, White, Flat Back of size 550 mm X 400 mm including 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe with PTMT check nut and union etc. complete all as specified and as directed.

Supply and fixing 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed by Engineer-in-Charge.

S & F Vitreous China Urinal, Half Stall Type, Flat Back or Corner Wall Type, White, complete including providing and fixing plugs, bedding urinal against wall in cement mortar [1:2], securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, 32mm bore PVC flexible waste pipe, PVC Connection of 15mm Bore and 450mm long with PTMT check nut and union etc., grating and union for discharge pipe, CP screws etc. complete all as specified and as directed.

Supply and fixing 16 mm outer dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

Supply and fixing 20 mm outer dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

Supply and fixing PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supply and fixing pillar taps 15mm dia bore fancy type with capstain heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified directed.

Supply and fixing 15mm bore stop valve fancy type,chromium plated , screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

Supply and fixing Stop Valves with wall flange, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, Fancy Type, screwed down high pressure with crutch or butterfly handle with long shank and cup [concealed type] for iron pipe etc complete all as specified and as directed.

Supply and fixing 15 mm dia Bib Taps with wall flange and areater, brass Chromium Plated, Fancy Type and screwed down to iron pipe or brass ferrule complete all as specified and as directed.

Supply & Fixing stainless steel Soap Dish of size 160mmx160mmx90mm with brass screws complete all as specified and as directed.

Supply & Fixing Towel rail, 20mm dia brass chromium plated, 600mm long with brass chromium plated brackets on both sides and fixed with steel screws, wooden rawl plugs complete all as specified and as directed.

Supply and fixing brass chromium plated over head 15mm bore shower rose of size 125 mm dia with 3 flow swivel joint including shower arm fixing to steel pipe or union complete all as specified

Supply and fixing 110mm bore PVC [SWR] pipes double socketed, in any length with rubber ring joints, laid in trenches or in floors /wall, as in weep holes complete all as specified and as directed.

Supply and fixing 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors /wall complete all as specified and as directed.

Supply & Fixing 100mm bore PVC [SWR] Floor Trap with grating including jointing with solvent cement complete all as specified and as directed.

Supply and fixing 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius, 110mm bore including jointing with solvent cement complete all as specified and as directed.

Supply and fixing Three layered Rotational Moulded Polythene [HDPE] Water Tanks, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 50 dia and 200 mm long spouts, connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed.

Supply and fixing 25 mm bore Ball Valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe [Minimum Weight 25mm - 455 Grams] etc. complete all as specified and as directed.

Supply & fixing gun metal gate valve 20mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Material and labour for 100mm thick cement concrete 1:4:8 type D2 (40mm graded aggreded) as in sub base, finish the surface even and rough to receive topping layer complete all as specified and as directed.

Material and labour for Providing 40mm thick PCC 1:2:4 type B-0 as in top surface, finish the surface even and smooth complete all as specified and asdirected.

Material and labour for Forming Contraction Joint [Dummy], 65mm deep X 10mm wide, filled with sealing compound and sealed with Sealing Compound Grade "A" complete all as specified and directed.

Material and labour for cement concrete 1:3:6 type C-2 (using 40mm graded aggregate) as in foundations filling and mass concrete complete all as specified and directed.

M & L for walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, built in Cement Mortar 1:6, with bond of PCC 1:3:6, type C-2 (in lieu of bond stone) complete all as specified and directed.

M & L Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling,uncoursed or brought face from straight edge held against the dressed surface not exceeding 40mm complete all as specified and directed.

M & L for Raised Pointing in Cement Mortar 1:4 to random rubble uncoursed or brought up to coursed masonry complete all as specified and directed.

M & L for Hand packing (any thickness) at back side of walls with broken stone of gauge 40 to 80mm and raising (or lowering) to the required level complete all as specified and as directed.

Material and labour for PCC (1:2:4) type B0 using 12.50 mm graded stone aggregate as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, benching, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and as directed.

Back filling of retaining wall using earth obtained from excavation work carried out under this Schedule complete all as specified and as directed.

Materials and labour for plain cement concrete Type B-1 1:2:4 using 20mm graded granite stone aggregates as in benching of manholes including forming centre channels half round or 1/4 section complete all as specified and as directed.

Materials and labour for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and as directed.

Material and labour for 150 mm bore RCC Pipes, Class NP2, laid and jointed with collars laid in trenches and jointed in cement mortar 1:1 complete all as specified and as directed.

Material and labour for Concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

Material and labour for providing precast reinforced cement concrete type C1 1:3:6 (using 20mm graded aggregates) as in Landings, Cover Slabs [for manholes etc], Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified and as directed. Note :-(i) Reinforcement and form work required shall be measured and paid seperately

Supply and installation of Conventional type LLDPE Septic Tank of 10 Users Capacity designed to carry Sewage and Sullage Water including excavation in any type of Soil, PCC 1:4:8, type D2 below Foundation, Vent Shaft connection etc. complete with upflow filter including media complete all as specified and as directed.

Material and labour for Soakage Well of for 25 users with excavation in any type of soil and constructed as per TD drawings No. CESZ/2020/TD-45, sheet No. 1/2 & 2/2 complete all as specified and as directed.

Supply & Fixing GI water tubing of 25 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

Supply & Fixing GI water tubing of 20 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

Material and labour for point wiring (surface type) for one light/fan/call bell point with 1.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade controlled by one way switch including 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for earth continuity wire connected to common earth dolly drawn through and including PVC double locked casing caping of adequate size with all accessories and PVC rectangular boxes for mounting switch socket and fan regulator etc complete all as specified and as directed. Note: (i) Wiring shall be done in proper colour coding using red , yellow, blue for phase, black for neutral and green for earth. (ii) Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

All as per item No 98 above but with FRLSH stranded copper conductor 2.5 sqmm (nominal area), two single core, PVC insulated and unsheathed cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet on independent board, including FRLSH PVC insulated stranded copper conductor 2.5 sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

Supply & fixing switch piano flush type, single pole, one way 5 Amp, 240 Volts complete all as specified & directed.

Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin, 5 and 15 Amps, 240 volt flush type 5 in 1 flush type with fuse & neon indicator complete all as specified and as directed.

Supply and fix ceiling rose surface Isolated body, 240 V, ISI marked Polycarbonate/ PVC three terminal complete all as specified and as directed.

Supply & Fixing Surface & wall mounted Energy efficient LED Tube Light Fitting of 20 watt, 4 feet long, 5700 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Supply & Fixing Surface & wall mounted, decorative ultra slim square profile, Energy efficient LED Tube Light Fitting of 10 watt, 2 feet long, 5700 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Supply & Fixing Energy efficient & Long life Building Security Light Luminaire, of 25 watt, 5700 K with Pressure Die Cast Aluminium Housing, IP66 protection, heat resistant glass cover, high power LEDs as light source, electronic driver including GI Bracket made out of 25 mm bore GI Tube, Medium Grade of size not exceeding 1.20 m in length and bent to shape required and fixed including drilling in wall of required hole with 2 Nos of wall fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Supply and fixing of MCB DB SPN 4 ways, powder coated, double door, 230 Volts, including bus bar neutral link, earth bar and din rail, for fixing MCB of various rating complete all as specified and as directed.

Supply & Fixing of MCB SP of capacity 6-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed.

Supply & Fixing of MCB SPN of capacity 32 Amps, 240 V, 10 KA 'C' curve complete all as specified and as directed. Note for serial Item No. 106 to 108: MCB and MCB DB shall be of same make as approved by GE/ AGE (I).

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm, connecting with flexible copper cable including making holes on the wall and making good to the disturbed surfaces complete all as specified and as directed.

Supply & Fixing Energy efficient, BEE 5 Star rated Storage type Water Heater [Geyser] 25 Litres Capacity with 2000 Watt Capacity heating element Conforming to IS - 2082, Vertical Storage type with Stainless Steel Inner Tank and ABS Outer Shell complete fixed to wall with suitable expansion fasteners including 02 Nos. of 450 mm long x 15mm dia Stainless Steel braided Flexible Hot & Cold Water connections and 15mm bore Non-Return Valve complete all as specified and as directed.

Supply, fixing, commissioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, 1100 volts, grade cross sectional area 6 sqmm 2.0 core laid in trenches/fixed to wall/under road/pipe as per IS 7098 (Part I) etc including cable glands, aluminium lugs complete all as specified and as directed. Note:-Excavation and earth work, brick protection, sand cushioning etc will be measured and paid separately

Material and labour for well burnt subclass 'B' bricks of size 230mmx115mmx75mm laid flat width wise along the length of cable for cable protection complete all as specified and as directed.

Materials and labour for sand filling around the cable with approved quality coarse sand for sand cushioning of Under ground cable including spreading and punning down to desired thickness complete all as specified and as directed. (Note: Punned thickness shall be measured for payment purpose)

Supply and laying 40 mm bore galvanised GI tubing, light grade with all fittings for passing of UG cables including complete all as specified and as directed.

Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on earthing set all as specified and as directed. Notes:- (i) Main earthing strip from earth plate electrode to rest point upto length of 7.5 meters length shall deemed to be included in the unit rate quoted against this item. (ii) On testing after completion if the desired resistenance is not obtained the contractor shall redo the earthing without any extra cost to the department. o the department.

M/s MATRI ENTERPRISES

sanjay kumar

Shri Atoshe Tuccu

M/S RAHUL TRADING CO.

M/S ARVIND GROUP OF CONSTRUCTION & INFRASTRUCTURE

M/S Lucky Builders

SK SINGH