ADDITION ALTERATION TO CEMILAC TECHNICAL ACCN P 3 WET CANTEEN AND SECURITY GUARD ROOM AT CIMILAC MARTHAHALLI BANGALO

Amount

Demolition of brick work, stone masonary or precast cement concrete blocks work, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles all as directed.

Demolition of cement Concrete in any description in any position not otherwise specifically provided

Demolition of Reinforced Cement Concrete like Roofs, beams (other than ground floors) beams, staircases, landings, chajjas and similar suspended work not exceeding 15cm thick complete all as specified and as directed.

Removal of demolished/excavated material [Soil] to a distance exceeding 5.00 KM and not exceeding 10.00 KM and depositing where directed complete all as specified and as directed.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L for providing Pre- cast cement concrete block masonry 1:3:6, Type C1 withsolid blocks, exceeding10cm in width and setting in motar, complete set in CM 1:6 complete all as specified and directed.

Material and labour for walling of random rubble masonry, brought upto course, well bonded, bedded and solidly hearted, built in CM (1:6) complete all as specified and directed.

M & L for rendering on stone masonary surfaces with 15 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering on stone masonary surfaces with 15 mm thick in Cement Mortar 1:4, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:4, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement including complete all as specified and as directed.

M & L for Hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rolled/rammed to a true surface and consolidated to required gradient and camber complete all as specified.

M & L for PCC 1:3:6, Type C-2, using 40mm graded stone aggregate as in sub base to Foundation, Filling, Mass Concrete, Sunken Floors etc complete all as specified and as directed.

M & L for PCC 1:5:10, Type E-2, using 40mm graded stone aggregate as in mass Concrete, sub base, Sunken Floors etc complete all as specified and as directed.

M & L for rendering 10 mm thick in Cement Mortar 1:3 over concrete sunken portion surface finished even and smooth with using WPC without using extra cement including complete all as specified and as directed. Note : WPC shall be measured and paid separetly under respective item

M & L for Polythlene film 50 Micron thick, laid on a coat of bitumen primer @0.30 to 0.50 Kg per Sqm. complete all as specified and as directed.

M & L for RCC M-25 (Design Mix) using 20mm graded stone aggregate as in foundations, rafts, footings, plinth beams, basement slabs etc complete all as specified and directed.

M & L for RCC M-25 (Design Mix) using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed.

M & L for RCC M-25 (Design Mix) using 20mm graded stone aggregate as in beams, bands, cantilevers, lintels over 1.5M span complete all as specified and directed.

M & L for RCC M-25 (Design Mix) using 20mm graded stone aggregate as in chajja etc complete all as specified and directed.

M & L for RCC M-25 (Design Mix) using 20mm graded stone aggregate as in slabs supported on walls, beams, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc., complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits of plinth beams and similar work for fair finished surfaces of concrete flat complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, columns and similar work for fair finished surfaces of concrete square, rectangular or polygonal complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including rough finished surfaces complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including rough finished surfaces complete all as specified and directed.

Use and waste formwork to Edges of Concrete Flats, Treads, Breaks in Floors, Window Cills, Concrete Railings, Ppenings in Concrete Walls, Floor and Roofs not exceeding 20cm wide and sides of RCC / PCC Bands in Walls, horizontal or sloping and similar work for rough finished surface of concrete complete all as specified and as directed

S & F Reinforcement using High Strength TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength TMT Bars of Grade Fe–500D of 6 to 8mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

Taking down chowkhat with shutter [without taking off shutter from the frame] not exceeding 1.50 Sq.m each complete all as specified and as directed.

Taking down chowkhat with shutter [without taking off shutter from the frame] exceeding 1.5 Sqm but not exceeding 4.0 Sq.m each complete all as specified and as directed.

Taking down shutters from the frames and refixing in same opening of any description exc 1 sq.m and n. exc 2 Sqm each.

S & F Rolled Mild Steel work confirming to Fe 410-0 or FE 310-0, Quality-A as in Framed work as in doors or gates of angle or other sections with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and as directed.

S & F Mild steel work as in doors or gate of ornamental and intricate design angle section gusset plate rails ladder & Hand rail including welding securing bolts including cutting tops to shape as directed, drilling holes etc conforming to Fe 410 -O or Fe 310 - 0, complete all as specified and directed by Engineer-in-Charge

S & F in repairs Collapsible Steel Gates, Top Hung, consisting of Channel Pickets, Pivoted Flat Bars, Top and Bottom Runners, Brass Handles etc. as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of new steel surfaces complete all as specified and as directed.

S & F Second Class Hard Wood, plain, solid, straight Chowkats and Frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S & F factory made pressed steel frame made out of mild steel black sheet of 1.25 mm thick of profile 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges (100 and 50mm), lock strike plate etc. Complete including one shop coat of priming and threshold of 12mm dia round bar 1 nos welded at bottom of frame all as specified and directed.

M & L for 1.60mm thick Plain, Black Sheet, mild steel sheeting as in in wall cladding, steel gates and similar work, cut to size, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and as directed.

M & L for 30mm thick Flush door solid core construction with veneer faced, black board core and ply wood face panels commercial type on both sides and both the faces are covered with decorative face veneer with lipping/frame to match . Bonding shall be with formaldehyde glue to ensure stronger bonding and longer life of door complete all as specified and as directed.

M & L for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S & F Black/Golden colour Solar control film 50 micron thick reflective type sticked to glass panes all as per manufacturer's instructions including taking down damaged filming complete all as specified and directed

Supply and fix 100 mm size Butt hinges, medium weight cold rolled mild steel all as specified and as directed.

S&F Aluminium anodised, barrel tower bolts of extruded section and fixed, 150mm long, complete all as specified and directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F Aluminium alloy anodised 250mm Sliding Door Bolt with hasp and staple [Bolt Type] of size 250 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Floor Door Stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

Hacking out old broken glass ( any thickness, size , quality or description ) from wooden frames or stone,concrete or brick surrounds,glazed with putty or fixed with beads complete

S&F 3 mm thick sheet glass, ordinary quality with rubber beading in square n.exc 1.0 sqm in each pane, frosted one side complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.5 mtr depth for foundation,laying cable etc and getting out in soft/loose soil all as specified and directed.

Excavation in trenches not exceeding 1.5 Mtr wide, exceeding 1.5 mtr and not exceeding 3.0mtrs depth for foundation and getting out in soft/loose soil all as specified and directed.

Returning, filling in soil including spreading, levelling, watering and well ramming in layers, not exceeding 25 cm thick all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as directed.

M & L for Vitrified Tiles, Double Charged, lifht shade, First Quality, area of each tile exceeding 0.36 Sqm and not exceeding 0.42Sqm, 9 to 10 mm thick as in Floors, set and jointed in cement slurry, finished with flush pointing in white cement or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Vitrified Tiles, Double Charged, lifht shade, First Quality, area of each tile exceeding 0.36 Sqm and not exceeding 0.42Sqm, 9 to 10 mm thick as in skirting, set and jointed in cement slurry, finished with flush pointing in white cement or coloured cement to match including screed bed or bedding layer of mortar 10 mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Granite stone slabs of 18 to 20 mm thick as in jambs, pillars, window cills, cooking platform, treads of steps etc including making holes and rounding exposed edges, with machine cut edges, rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of any colour / shade, design / pattern as directed, set and bedded with grey cement [slurry] and jointed and pointed with white cement slurry (1:2) mixed with a admixture of pigment to match shade of granite slabs including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Coloured, Premium Quality, of size 450 mm X 300 mm, 7 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. The colour / shade / design of tiles shall be as approved by GE.

M & L for 25mm thick, PCC 1:2:4, type B-1, using 20mm graded stone aggregate as in floors/paving finished rough to receive cement tiles complete all as specified and directed.

Dismantling of Ceiling board any description fixed in any position with screws complete all as specified and as directed.

Supply and fixing of ceiling system with fine figured edge tiles having humidity resistance (RH) of 95&. NRC 0.34 light reflectance approx 84 & thermal conductivity K-0.052 – 0.057. W/mk colour white fire performance of class-1 as per BS 476 part 6 & 7 in module size of 600 x 600 x 16 mm thick suitable for green building application with recycled content of 38-41% with Armstrong or equivalent silhouette profile exposed grid system with 15mm white flanges incorporating 6 mm central reveal in white/black colour. Silhouette, main runners & cross tee to have mitred ends & birds mouth notches to provide mitred cruciform junctions. The Tee sections have a galvanizing of 170 gms per sqm & passed through 500 hrs of salt test. The main runner spaced at 1200 mm c/c should be securely fixed to the structural soffit using suspension system at 1200 mm maximum c/c. The first / last suspension system at the end of each main runner should be greater than 450 mm from adjacent wall. Cross Tee 1200 mm long should be interlocked between main runners at 600 mm module. 600 x 600 mm module is formed by fitting 600 mm long flush fitting cross Tee, perimeter trim consist of wall angles of size 3000 x 19 x 19 mm secured to wall screws at 450 mm c/c.complete all as specified and directed. Make: Arm strong / Saint Gobain

Taking down PVC (SWR) pipe of any dia from trenches/ floors or fixed to wall complete all as directed.

S & F PVC (SWR) pipe 110mm bore, single socketed in any length with rubber ring joints fixed to wall complete all as directed.

S & F PVC (SWR) pipe 75mm bore, single socketed in any length with rubber ring joints fixed to wall complete all as directed.

S & F PVC (SWR) pipe 250mm bore, single socketed in any length with rubber ring joints including all fittings like bends and shoes etc laid in trenches/ floors or fixed to wall complete all as directed. Note: Height upto 20M and rate quoted deemed to include for necessary scaffolding

S & F PVC (SWR) bends 75mm bore, any radius complete all as directed.

S & F PVC (SWR) bends 110mm bore, any radius complete all as directed.

S & F PVC (SWR) floor trap with 75mm dia outlet, plain with grating including jointing with solvent cement complete all as directed.

S & F PVC (SWR) gully trap125/110mm including jointing with solvent cement complete all as directed.

S & F in repairs Wash down water closet (Pedestal pattern), Vitreous China white(ETWC), plastic water closet seat (ETWC) of same colour closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Supply only plastic water closet seat, white closed pattern with flat bottom and cover and MS chromium plated or aluminised hinging device complete all as specified and as directed.y

S & F in repairs Vitreous china squatting pan "Orissa pattern" of size 580 mm X 440 mm, White with integral foot rests and 'P' or 'S' trap 100 mm dia including provision of lime concrete bedding complete all as specified and as directed.

S & Fin repairs PVC valve less, syphonic action type, flushing cistern, 10 Litres capacity, low level, white, with inlet, ball valve, float and handle, brackets complete including PVC outlet pipe all as directed.

S & F in repairs Flush pipe of polyethylene of low and high density of 32mm dia for low level cistern all as specified.

S & F in repairs Vitreous china wash basin, white, angle back (Oval Type)of size 550 x 400mm excluding taps, waste, chain and plug and porcelain stopper including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed

S & F in repairs 15mm dia Pillar taps, Sensor type with automatic on/off, cast copper alloy with long neck, chromium plated fancy type with aerator, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S & Fin repairs Vitreous china sensor type urinals 370x390x610mm size, half stall type with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing grating and Union for discharge pipe complete all as specified and directed.

S & F in repairs Vitreous china urinal partition, white, of size 310 X 770 mm complete all as specified and as directed.

Supply and fix brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing union cap and fixed 32 mm, in repair complete all as specified and directed

S & F in repair PVC connection 15mm size 450mm long with PTMT nuts complete all as directed.

S & F in repair Stop valves, 15mm bore, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as specified and as directed

Supply and fix Health faucit assembly, brass, chromium plated consist of valve, sprayer, PVC flexible pipe for EWC suitable for 15 mm bore pipe fixed complete.

S & F in position chromium plated recessed type Toilet paper roller holder with flap of size 150x150mm with necessary CP screws and washers fixed to walls all as directed.

Supply and fix soap dispenser chromium plated Make Jaquar CAT No 1137 or equivalent

S & F in repairs Angle Cock, 15 mm dia,fancy type, Chromium Plated with long shank and cup, without flange complete all as specified.

S & F in repairs Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as directed.

Dismantling of water tanks 1000 litres capacity and removing to store complete all as specified and directed

S & F Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litres capacity, double layered, hoisted and fixed in position with polythene float and flynut complete all as specified and directed.

S & F in repairs Ball Valves, 25 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe [Minimum Weight 25mm - 455 Grams] etc complete all as specified and as directed

Taking down GI tubing/ CPVC pipe of 25/32 mm bore with all fittings and connections all as specified and as directed

Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11including all fittings in trenches and walls complete all as specified.

Supplying and laying of 32mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11including all fittings in trenches and walls complete all as specified.

S & F in repairs CPVC Gate Valve 25 mm outer dia confirming to IS, ISI Marked complete all specified and as directed.

S & F in repairs CPVC Gate Valve 32 mm outer dia confirming to IS, ISI Marked complete all specified and as directed.

S & F in repairs Bib taps, fancy type, 15mm bore, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed

M & L for 25mm thick, PCC 1:2:4, type B-0, using 12.5mm graded stone aggregate as in floors/paving finished rough to receive cement tiles complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3.5 Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (Weight not less than 150 gms/Sqm) laid by torching method over primed surface with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion including bituminious primer confirming to IS-3384 applied @ 0.3 ltr/Sqm. The complete roof treatment shall be consisting of as under after laying levelling coarse as described above :- (a) Taking down old/existing roof treatment including APP membrane. (b) Applying one tack coat of bitumen 85/25 grade @ 1.2 Kg/Sqm for sealing the existing cracks if any (c) Applying one coat of bituminous primer conforming to IS 3384 @ 0.3 ltr/Sqm (d) Laying of APP based membrane as specified thickness and weight. (e) Applying two coats of aluminium paint @ 100 ml per Sq.m for each coat on top of water proofing treatment including removing the rubbish from the site complete all as specified.

M&L Applying PUROOFKOAT,single component,cold applied,water based Polyurethane modified acrylic dispersion with highly elastic and UV resistant water proofing treatment to the sunken floor/Roof@ 1.2kg/per m2 to confirm to ASTMD 6083-97 a with a density of 1.25 to1.3 kg/per ltr,having tensile strength of 1.5N/mm2, having elongation of 350% with solid content not less than 60% in 3 coats including self-priming of same material after dilution of water at 50% and spreading 60gsm Geo-Textile between two top coats including taking down/removing old reatment complete all as specified and as directed

M & L for 75mm thick, PCC 1:3:6, Type C-2, using 40mm graded aggregate as in Plinth protection etc. surface finished even and smooth with out using extra cement complete all as specified and as directed.

M&L applying 2 coats of Exterior emulsion on wall surface with Acrylic Smooth exterior paint of required shade applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) on wall new & old plaster surface including cornices, plasters & complete removal of old surface etc by all as specified and directed

M & L for preparation of newly plastered Wall surfaces and applying two or more coats of Cement based Wall Care Putty of 2mm on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Distemper oil emulsion over one of alkali resistant primer on Wall surfaces complete all as specified and as directed.

M & L for Complete removal of existing treatment of any description on Wall surfaces and applying two or more coats of Cement based Wall Care Putty of 2 mm on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Distemper oil emulsion over one of alkali resistant primer on Wall surfaces complete all as specified and as directed.

M&L preparation of old plastered or unplastered surface of walls and applying one a coat of Distemper oil emulsion complete all as specified and directed

M & L for Complete removal of existing treatment of any description on ceiling surfaces and applying two or more coats of Cement based Wall Care Putty of 2 mm including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Distemper oil emulsion over one of alkali resistant primer on ceiling surfaces complete all as specified and as directed.

M&L preparation of old plastered or unplastered surface of ceilngs and applying one a coat of Distemper oil emulsion complete all as specified and directed

M & L for preparation of old painted steel and iron based surfaces of any description over 10cm width or girth and applying one coat of Synthetic Enamel paint complete all as specified and as directed.

M & L for preparation of old wooden surfaces over 10cm width or girth and applying one coat of Synthetic Enamel paint complete all as specified and as directed.

S & F Powder Coated Aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators, partitions with one or more rebates including jointing cleat, rubber beading for fixing, locking arrangement etc complete all as specified and as directed.

S & F Aluminium Powder Coated [Minimum 50 Micron thick] Sections as in door shutters, Aluminium section weighing 0.55 KG / RM including necessary Joining Cleats, Glazing Clips, Neoprene Rubber Packing, Powder Coated Aluminium Snap Beading, Screws, Powder Coated Aluminium Fittings such as Locking Arrangement [1 No], Suitable Handle [2 Nos] per Shutter complete all as specified and as directed. Note: Unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing, fittings such as Handles, Locking Arrangement and fixing only of Panel inserts such as Glass / Gauge / Grills etc.

S & F Aluminium Powder Coated [Minimum 50 Micron thick] Sections as in Window and Ventilator Shutters, Sliding Type, without Sash Bar, Aluminium section weighing 0.55 KG / RM including necessary Joining Cleats, Glazing Clips, Neoprene Rubber Packing, Powder Coated Aluminium Snap Beading, Screws, Powder Coated Aluminium Fittings such as peg stays 150mm [1 No], hinges type B-21 100mm long[2 nos] Suitable Handle [1 No] per Shutter complete all as specified and as directed. Note: [a] Supply only panel inserts such as Glass / Gauge / Grills will be measured and paid separately. [b] Unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing, fittings such as Handles,Peg stays, Hinges etc.

M & L for 5.50 mm thick sheet glass ordinary quality frosted on one side exceeding 0.50 Sq.m each pane glazing with rubber beading as in doors and partions complete all as specified and as directed.

S & F 12mm thick, Exterior grade, Prelaminated Particle Board, prelaminated on one side with decorative choice lamination and other side balancing white lamination, interior Grade fixed with screws to timber frame work complete all as specified and as directed.

M & L for 4.00 mm thick sheet glass ordinary quality in square exceeding 0.50 Sq.m each pane glazing with rubber beading as in windows complete all as specified and as directed.

S & F for venetian blinds verical type 100 mm width with approved fabric and powder coated aluminium fittings such as top rails, metal weight, nylon button loops etc complete all as specified including dismantling unserveable one.

S & F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

S & F Door Closer Hydraulically Regulated, Designation No. 3 universal type, suitable for door shutters of 851 mm to 1000 mm in width and of weight between 61 to 80 Kg of aluminium body complete all as specified and as directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories &stainless steel dash fasteners,stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement etc complete all as specified and directed.

S & F Structural Glazing with 12mm thick wave free toughened clear glass with stainless steel spider fitting,fish mouth channel in bottom and top as per design with and including provision of all other neccessary fixture and accesaries,complete all as specified and directed.

M&L PCC 1:2:4 type B1 using 20mm graded stone agregrate as in coping and other similar work including weathering, slightly rounded or chamfered angles and thorating etc (Note : rate including necessary form work).

Demolition and breaking up drain pipes of any size (Salt glazed ware, AC or Reinforced concrete) set in cement mortar.

Material and labour for 200 mm dia Reinforced cement concrete pipe with collars, class NP2 laid in trenches and jointed complete as specified and directed

Material and labour for 450 mm dia Reinforced cement concrete pipe with collars, class NP2 laid in trenches and jointed complete as specified and directed

M&L for PCC 1:4:8 type D2 as in bed concrete to 200 mm dia drain pipe including packing under and completely surrounding pipes with concrete after they are laid and tested.

M&L for PCC 1:4:8 type D2 as in bed concrete to 450 mm dia drain pipe including packing under and completely surrounding pipes with concrete after they are laid and tested.

Dismantling of wrought iron or Mild Steel work of any description like MS grills and similar items complete all as specified and as directed.

Taking down carefully copper / aluminium point wiring [light, fan, socket or power] complete including fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. and making good the disturbed surfaces all as per existing complete all as specified and as directed.

M&L Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 Volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit (minimum 20 mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I, ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/ recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets, fan regulators with required modules all as specified etc for One Light / Fan Point controlled by One Switch complete all as specified.

All as per Item No.127 here-in-above but for One 3 pin socket outlet, 6 Amps on independent board

All as per item No. 127 here-in-above but for One 3 pin socket outlet, 6 Amps on the same board

All as per Item No. 127 here- in- above, but 2.5 sqmm copper conductor wiring with 1.5 sqmm copper conductor as earth continuity for power point of 16 Amp.

S & F Modular switch one way, 6 Amp, one module, (ISI marked), complete all as specified and directed.

S & F Switch, Modular Type, One Module, Single Pole, One Way, 16 Amps, 230 Volts complete all as specified and as directed.

S & F Socket Outlet, 2/3 pin, 6Amps and combined Modular Type, Two Modules, 230 Volts complete all as specified and as directed.

S & F Ceiling Rose, Surface Bakelite/PVC, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed.

S & F Socket Outlet, 2/3 pin, 6/16Amps and combined Modular Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed.

Hanging only ceiling Fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

S & F Electronic Fan Regulator, Stepped Type, Modular Type, One Module, 100 W, AC, 230 Volts, Single Pole complete all as specified and as directed.

Supply and fix sheet metal enclosure for pre wired MCB distribution board double door, powder coated Single pole & Neutral 12 way , 240 volts, single phase with 200 Amps rated tinned electrolytic copper bus bar with neutral link including taking down old MCCB/MCB and DB complete all as specified and directed.

Supply and fix sheet metal enclosure for pre wired MCB distribution board double door, powder coated Single pole & Neutral 8 way , 240 volts, single phase with 200 Amps rated tinned electrolytic copper bus bar with neutral link including taking down old MCCB/MCB and DB complete all as specified and directed.

Supply and fix sheet metal enclosure for pre wired MCB distribution board double door, powder coated Single pole & Neutral 4 way , 240 volts, single phase with 200 Amps rated tinned electrolytic copper bus bar with neutral link including taking down old MCCB/MCB and DB complete all as specified and directed.

M & L for Sub main wiring with 2 runs of single core 4 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawn through and including suitable PVC non matallic rigid conduit with accessories fixed on Walls / Roofs / Floors / Ceiling etc. and connecting terminal ends including One run of 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, green in colour, 1100 Volts, FRLS Grade as earth continuity conductor including taking down existing submain wiring complete all as specified and as directed. Note: 3 runs of 4 Sq.mm & one run of PVC conduit with accessories will be measured as one RM.

M & L for Sub main wiring with 2 runs of single core 6 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawn through and including suitable PVC non matallic rigid conduit with accessories fixed on Walls / Roofs / Floors / Ceiling etc. and connecting terminal ends including One run of 6Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, green in colour, 1100 Volts, FRLS Grade as earth continuity conductor including taking down existing submain wiringcomplete all as specified and as directed. Note: 3 runs of 6 Sq.mm & one run of PVC conduit with accessories will be measured as one RM.

S&F of MCB TPN 240 Volts, 'C' series, breaking capacity 10 KA of rating 100Amps complete all as specified and as directed.

S&F of MCB SPN 240 Volts, 'C' series, breaking capacity 10 KA of rating 32Amps complete all as specified and as directed.

S&F of MCB SP 240 Volts, 'C' series, breaking capacity 10 KA of rating 6 to 32 Amps complete all as specified and as directed.

Supply and fix Recess mounted full panel LED luminaire 36 watt fitting 2' x2' with White powder coated housing & frame in CRCA sheet, High efficiency LED grade diffuser, electronic driver duly wired upto terminal block, CRI>80, Colour temperature-5700K, IP20, 50000 burning hours as per L70 Criteria, Ambient temperature-0 to 50DegC, Driver Efficiency>85%, THD<10%, Powerfactor>0.95, Surge protection in CM-3KV, Multistage isolated Constant current-Constant voltage operated driver with range 150-270V AC and Safety extra low voltage safe level<60V DC as per IEC Standard complete all as specified and directed

S & F LED Luminaire 20 Watt fitting, batten type, 4' long with white powder coated housing & frame in CRCA sheet, High efficiency LED grade diffuser, eletronic driver duly wired upto terminal block, CRI>80, LED colour temparature - 5700k, IP20, 50000 burning hours as per L70 criteria, ambient temparature - 0 to 50 Deg C, Driver efficiency >85%, THD<10%, PF>0.95, surge protection in CM-3KV, Multistage isolated constant current, Constant voltage operated driver with range 150-270V AC and safety extra low voltage safe level< 60V DC as per IEC standard complete all as specified and directed

S&F High efficient LED Street light fitting 60 watt, with Aluminium pressure Die cast housing parts for long life, with toughnened galss with a option of secondary optic, High purity PC Fresnel diffuser with silicon gaskets for IP65 Protection, in-built electronic driver pre- wired up to terminal block,Suitable for external pole dia. Up to 35 mm, CRI >70,Temperature range- 0 to 45DegC, Driver efficiency>85%, Power factor>0.95, THD<10%, Colour Temperature- 5700K, Surge protection in CM-3.5KV, 50000 burning hours as per L70 Criteria, Multistage Isolated Constant Current- Constant Voltage Operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard and connecting from power source with 3 core 4 Sqmm insulated copper cable complete all as specified and directed

Earthing complete with Galvanised Steel Earth Plate Electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of Plate not less than 1.50 m below normal ground level connected to 4 mm GI Wire [Earth Lead] and GI pipe 15 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:3:6, Type C1 earthing chamber] Pit with precast slab 50mm thick in cement concrete (1:2:4) type B1, Reinforced with welded steel wire fabric (XPM) weight not less than 4 KG/SqM , CI frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. and disconnecting and taking down existing Earthing of any description complete all as specified and as directed. Note : Earth resistence not exceeding 1.0 Ohms

Supply, install, testing and commissioning of five star rated hi-wall split units indoor/outdoor with cordless remote control unit with all standard accessories and with in built air ioniser and plasma filter for better indoor air quality with latest inverter technology having eco friendly refrigerent gas, copper condenser coil, EER 3.2 of capacity 2.0 TR complete all as specified and directed by the Enginer-in-Charge. [Make: BLUE STAR / HITACHI / DAIKIN / CARRIER] NOTE:- The rate quoted shall deemed to include for copper tube of size 24SWG of 5/8 inch and 1/4 inch dia of superior qualitysuitable for refrigeration suction/discharge line along with tubular insulation of suitable length from indoor to outdoor unit, 3 core 4 sqmm copper wire of required length, MS stand for fixing 2 TR out door unit duly painted and refrigerant gas

S & F voltage stabiliser for automatic operation, single phase naturally air cooled, copper wounded as per IS 8448-1989 with digital display, wall mounted, indoor type & designed for input variation between 170 Volts to 250 Volts with output voltage stabilsed at 230 Volts with time delay and of capacity 5 KVA complete all as spcified and directed. [Make: V-GUARD / UNISTAB / VOLINA / VOLTAMP / VINTEK]

M& L of dismantling existing split/ window AC 1.5/ 2 Ton including connected accessories and shifting to safe custody and refixing the sameat the place where directed including opening/drilling of size 65 mm dia, using heavy duty stone driller/cutter machine in the stone machinry wall for installing spilit type air conditioners and for passing suction and discharge refrigerant pipe lines, drain pipe, cable etc including testing and commissioning and making good the disturbed surface complete all as specified and directed

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm dia and over upto and including 8mm dia as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F HDPE drain pipe of 20mm bore fixed to wall/roof complete all as specified and directed by Engineer-in-Charge. [Make: KISAN / JAIN IRRIGATION / FINOLEX / SUPREME / PRINCE]

PRAGATHI BUILDERS

Lucky Enterprises