Civil and Electrical renovation of Embedded System prototyping lab high power system lab system testing calibration lab at CSIR CEERI

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead within CEERI campus as per direction of Enginner In Charge.

All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering,lead within CEERI campus and for all lift

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes

Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing Ist quality ceramic glazed wall tiles (Size not less than 300 mm x 450 mm) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades (light,dark and designer etc ) of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand),having below rough plaster of average 20 mm of 1:4 ( cement :4 coarse sand) for surface preparation and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing aluminium body Cam Action Slide Channel Overhead hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment and 90 degree stop arrangement, of approved quality and make with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Size 250x10 mm

Size 100x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

Size 125 mm

Providing and fixing bright SS finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of strainless steel 304 lever handles of approved quality and make with necessary screws etc. complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding,fastners and bolted with special shaped washers etc. complete

Hot finished welded type tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

Plate in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and laying Vitrified tiles with spacer in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness including grouting of joints (Payment for grouting of joints to be made separately). The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily including levelling of existing floor with cement mortar 1:3 (1 cement : 3 coarse sand) etc complete

Glazed Vitrified tiles Matt/Antiskid finish Size of Tile 600 x 600 mm

Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete :

With residual type petroleum bitumen of grade VG -10

10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat:

With common burnt clay F.P.S.(non modular) brick tile of class designation 10

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including chasing,finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised -Rigid PVC rainwater pipes including jointing with seal ring leaving 10mm gap for therrmal expansion. Single socketed pipes. 160 mm diameter.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 160mm shoe

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. Bend 87.5°, 160 mm bend

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer?in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

15 mm cement plaster on rough side of single or half brick wall of mix:

1:4 (1 cement: 4 coarse sand)

Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement.

Ordinary cement finish using ordinary cement

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required and including water thinnable priming coat with cement primer, to achieve even shade & colour and scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Two or more coats

Finishing walls with Acrylic Smooth exterior paint of required shade :

Two or more coat applied @ 1.67 ltr/ 10 sqm over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat to achieve even shade & colour and scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete on existing cement paint surface/rough cast plastered surface

Providing and fixing bright finished hooks and eyes in aluminium , ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade and approved quality and make with necessary screws etc. complete

Size 150 mm

Demolishing cement concrete manually/ by mechanical means including disposal of material within CEERI campus lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing brick work,stone work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within CEERI campus lead as per direction of Engineer - in - charge.

In cement mortar

Dismantling doors, windows,rolling shutter and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within CEERI campus lead and repair and finsh the jambs in proper way:

Of area 3 sq. metres and below

Of area beyond 3 sq. metres

Dismantling steel work in built up sections at any height in girder, angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within CEERI campus as per direction of Engineer-In-Charge.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within CEERI campus as per direction of Engineer-In-Charge.

G.S./asbostas sheet

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within CEERI campus as per direction of Engineer-In-Charge.

Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.

Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (Old CC paver blocks shall be supplied by the department free of cost).

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm Hubless centrifugally cast iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, long pvc bend with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets and dash fastner, 15 mm C.P. brass pillar cock with central hole and long braided hoses , 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required :

White Vitreous China Wash basin size 550x400 mm with C.P. brass pillar basin mixer with central hole and long braided hoses

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe 32 mm dia

Providing and fixing mirror of size 600x450 mm superior glass (of approved quality) and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing, fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing soil, waste and vent pipes :

100 mm dia Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete

100 mm dia Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

Providing and fixing plain bend of required degree.

100 mm dia Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

Providing and fixing terminal guard

100 mm Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe

100 mm dia SS 304 grade coupling with EPDM rubber gasket

Providing and fixing Steel finished clamps with base holder plate with accessories etc complete for sand cast iron/ centrifugally cast (spun) iron pipes of diameter :

100 mm dia

Providing and fixing P-trap / Floor trap of self cleansing design with screwed down or CP hinged grating with frame with or without hole, vent arm complete, including cost of cutting and making good the walls and floors :

100 mm inlet and 100 mm outlet Hubless centrifugally cast iron offsets epoxy coated inside & outside as per IS:15905

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls and floor etc. Internal work - Exposed on wall including synthetic enamel paint of approved brand and manufacture of required colour to give an even shade

15 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps,i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall

15 mm dia nominal bore

Providing and fixing uplasticised PVC connection pipe in SS finish with brass unions :

45 cm length & 15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water torage tank,IS: 12701 marked,with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes with 03 nos tank nipples and the base suppport for tank & including providing and fixing 20mm dia ball valve (brass) of approved quality, High or low pressure, with plastic floats complete for each tank.including taking down existing pvc tank & deposited in store yard as per direction of Engineer in-Charge.

Providing and fixing C.P. brass bib cock with wall flange of approved quality conforming to IS:8931 as per direction by Engineer in charge.

15mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 with wall flange as per direction by Engineer in charge

15mm nominal bore.

Cutting holes up to 30x30 cm in walls including making good the same:

with common burnt clay F.P.S. (non modular) bricks

Providing,laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints including trenching , refilling and dismalting of existing old SW pipe etc.complete :

100 mm diameter S.W.pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

100 mm diameter S.W.pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight FRP/GRP cover with frame of 300 x300 mm size (inside) the load capacity of cover to be not less than 12.5T as per standard design:

150 x 100 mm size P type without common burnt clay F.P.S (non modular ) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing strainless steel hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge

Powder coated minimum thickness 50 micron aluminium

Providing and Fixing 0.50 mm thick PVDF (Poly Vinylidene fluouride) both side of aluminium thickness 3.00 mm overall thickness 4.00 mm on walls,in doors & ceiling with proper required haging system and having fire rating of 120 minutes and fixing with silicon tape/ adhessive material as required ,in opening shutters and fixed sections including cutting PVDF sheet as per required at site, preparing smooth surface and making holes/making good as required cutting hoisting and fixing aluminium members etc. complete as directed by Engineer-In-Charge

Providing and applying one coat of cement based ready made wall putty including preparing the surface smooth by san papering etc as per directions of the Engineer-in-charge. Consumption of the putty shall be not less than 5 Kg per 10 Sqm. Preperation and application of the putty shall be strictly as per the manufacturers guidelines and as per the directions of the Engineer-in-Charge. The putty shall be applied only after cleaning the surface thoroughly. Required curing shall be done before application of both the coats shall also be sand papered with Amery paper no. 320 No. to make the surface smooth and even suitable for any kind of wall painting. The rate includes all operations and all the material and necessary scaffolding etc. Complete as per direction of Engineer-In-Charge.

Providing and fixing homogeneous Polyvinyl chloride sheet / tile of 2.00mm thick in flooring and skirting in approved pattern on a smooth and damp proof base using rubber based adhesives of approved quality and manufacturer including welding of joints if required and rolling with light wooden roller weighing about 5 kg., all complete as directed by Engineer-in-Charge, in approved colour and shade including removal of old pvc flooring if required & preparing the smooth surface etc. as per direction of Engineer - in - charge.

Repairs of reveals and jambs of doors and windows with cement mortar 1:3 (1 cement : 3 fine sand) including chiseling the damaged area and disposal of mulba in low laying area in CEERI Campus as per direction of Engineer-In-Charge.

Repairs of cracks in walls by chiseling the cracked area upto 300 mm width as directed by the Engineer-in-Charge and filling with mortar in cement mortar 1:3 (1 Cement : 3 fine sand) before placing fibre glass mesh 150 mm wide of approved quality including disposal of mulba in low laying area in CEERI Campus etc as per direction of Engineer-In-Charge.

Providing and fixing Steel finished clamps with base holder plate with accessories etc complete for PVC/ centrifugally cast (spun) iron pipes of diameter : For 160 mm dia pipe etc. complete as directed by Engineer-In-Charge

Opening and refixing steel hollow section with precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Part 'B' Electrical Work - Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Supplying and fixing following size/ modules, GI box alongwith modular base, cover & blanking plate for modular switches in recess etc. as required. etc as required.

1 or 2 Module (75mmX75mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections butexcluding modular plate etc. as required.

Telephone socket outlet RJ 11

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch,after removing recessed existing board, disconnection making connections and testing etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 Nos. 3pin, 6 amps modular socket outlet with 1 No. 16 amp moduler switch and 1No. 6 pin 5/6 & 15/16 amps modular socket with 1no 16 amp moduler switch, blanking ,connection, painting etc. as required (different in colour of cover plate from general power for UPS / computer applications), making good the wall with matching colour distemper/ white wash etc. as required. (anchor penta or equivalant make)

Supplying & fixing following amps rating, 240 volts, "C" curve, MCB suitable for inductive load of folloing pole with suitable size MCB box encloser complete with connections, testing and commissioning etc. as required.

63 amp Four Pole with encloser

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 4 sq. mm + 2 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required.

2 x 1.5 Sq. mm

3 x 2.5 sq. mm

3 x 4 sq. mm

Telephone & Data - Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying & Fixing of following sizes of steel conduit along with heavy duty accessories, junction box etc. in surface / recesse including painting in case of surface conduit, or cutting the wall, repair and making good the same as required.

Supplying and drawing of 23 AWG UTP Data Cable (CAT 6) gigaspeed LAN Cable in the existing surface/ recessed Steel/ under floor trunking as required.

1 run of cable

P & F following modular accessories made out of unbreakable and fire retardant poly carbonate with silver contacts Simplex Faceplate with RJ-45, information outlet with shutter with colour coding on existing modular plate, including making connections testing etc. as required

Light and Fan- Supply of following sizes of BLDC energy saver ( 5 star rated) ceiling fan without regulator complete with double ball bearing, motor, blades, down rod, canopy, etc. complete as required.

Size 1400 mm.

P & F 18 swg M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge.

Installation, testing and commissioning of ceiling fan, including wiring with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. complete as required.

P & F of heavy duty capacitor start Exhaust fan Size-300 mm sweep, 900 RPM, single phase, IS: 2312 marked of Havells make model-Turbo force SP or other approved make in existing opening including grouting of metal fastener with bolts, nuts making connections , testing etc. as reqd.

Supplying of Surface / Ceiling mounted LED light fixture-1200mm, Philips 36 W Cool White Smart Brite Surface Light, 6500 K with housing Type-SM270C LED 30S 6500 PSU WH Philips or Equivalent other make (Bajaj/ Crompton/Syska / Wipro) including hanging arrangment with clutch wire, connection wire of suitable length, all accessories etc. as required.

Installation, testing and commissioning of above LED tube light fittings complete with all accessories on surface of wall/ ceiling or suspended from ceiling including providing hanging arrengment , transperent/suitable connection wire/ 1.5Sq.mm FR PVC copper conductor etc. as required.

Supplying of recessed mounted 36 Watt full glow, slim energy efficient, Green Square 2'x2' LED lighting luminaires Type- RC380B LED42S-6500 G6 L60W60 PSU OD, Philips or equivalent make complete with hanging arrengment all accessories, metallic CRCA powder coated housing etc. complete as required.

Installation, testing and commissioning of above LED tube light fittings complete with all accessories on surface of wall/ ceiling or suspended from ceiling including providing hanging arrengment , transperent/suitable connection wire/ 1.5Sq.mm FR PVC copper conductor etc. as required.

Supplying and fixing 10 amp 'C' Curve modular DP MCB on the existing modular plate including connections but excluding modular plate etc. as required.

Cables Supply of XLPE insulated PVC sheathed 1.1 kv. Grade al. conductor armoured Cable IS: 7098 Part-1 of approved make.

4 X 50 Sqmm Al. Cable

4 X 16 Sqmm Cu. Cable

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade on wall/ roof/ duct/ shaft including fixing by means of screws & rag bolts, suitable size MS U clamps complete as per specifications, repairing works etc as reqd. of following sizes of cables.

upto 35 Sqmm.(clamped with 1mm thick saddle)

above 50 sqmm upto 95 Sqmm.(clamped with 1mm thick saddle)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

above 50 sqmm upto 95 Sqmm

Supply& making one end termination with heavy duty single compression brass gland SIBG type, aluminium/ copper lugs duly crimped with crimping tool, PVC tape etc. for following size of XLPE insulated & PVC sheathed aluminium/ copper cable of 1.1 KV grade as required.

4 X 50 Sqmm Cable

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Distribution Boxes (Main DBs) Supplying and fixing of ,4 Way three pole and neutral, prewired, sheet steel, per phase isolation ( PPI ) MCB distribution board, 415 volts on surface / recess, complete with loose wire box, Incomer 1No. 63A, 4 Pole isolator, Outgoings- 3Nos. DP RCCB 40A, 240 volts, having a sensitivity current 30 milliamperes, 12 Nos. SP AC MCB-32A, 10KA, 240V ( 'C' curve ), terminal blocks, duly prewired with suitable size FRLS PVC insulated copper conductor upto terminal blocks, tinned copper bus bar, seperate neutral links for each phase, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted, making internal DB terminations with copper lugs including all the existing incoming/ outgoing connections, earthing, testing, repair & making good the wall with matching colour distemper/ white wash etc. as required.

P & F Recessed/ surface mounting vertical type heavy duty Double door type TPN-4 way sheet steel phosphatised powder painted Distribution Board with incomer 1No. MCCB-125A, 16KA and 4 Nos. TP AC MCB-63A 10KA ( 'C' breaking characteristic) for outgoing circuits, 200 Amp busbar, neutral link, earth bar & din rail etc conforming to IS; 13032, IS; 8623, BS; 5486 of approved make including making all the incoming/ outgoing connections, internal DB terminations with copper lugs, testing etc. as required.

Earthing Plate Earthing as per IS: 3043 with copper earth plate 600 x 600 x 3 mm thick by embodying 4 mtr below the ground lavel with alternate layers of salt and charcoal (95 kg. each) with 20 mm dia G.I. B class watering pipe including all accessories like nut, bolts, reducer, nipple ,wire meshed funnel, and C.C. finished chamber covered with hinged type with locking arrangement C.I. Cover, C.I. Frame of size300mm x 300mm complete and testing of earth resistance as required.

P/F 25mm x 5mm copper strip in 40mm dia G.I. Pipe from earth electrode. including connection with brass nut bolt spring washer excavation and refilling as rqd.

Providing and fixing 25 mm X 5 mm copper strip on surface/wall with providing insulating support for connections etc. as required.

DEVENDRA KUMAR (BID ID -835130)

sihag construction (BID ID -834713)