Construction of Residential Quarters for Higher Class Officers (Type-6) on Plot No. 186 to 193, C.S. No. 1977 behind Yashodhan Building, Dinshaw Waccha Road, Mumbai. (Including Electrical Work)

Amount

Removing the tiles, batten sand dungry cloth purlins, rafters and ridges etc. from roof, sorting out the serviceable and unserviceable materials and stacking the same as and where directed in the compound, scaffolding etc. complete.

Removing King Post truss from roof and stacking the materials as directed with all leads and lifts etc. Complete

Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete.

Dismantling brick masonry in lime or cement mortar and stacking the materials as directed with all leads, lifts etc.

Removing urinal pans or wash hand basins with frame including disconnecting the sanitary and water supply connections, removing the same carefully and stacking the serviceable materials as and where directed including throwing the unserviceable materials outside etc. complete

Removing W.C. pans including disconnecting the sanitary and water supply connections, removing and breaking flooring and bed concrete around pan removing the same carefully and stacking the serviceable materials as and where directed including throwing the unserviceable materials out side etc. carefully and throwing out the refusal outside etc. complete.

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete.

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. Complete

Removing lime or lean cement concrete including stacking the spoils as directed with all leads, lifts etc, complete.

Dismantling stone masonry in lime or cement mortar including stacking the materials as directed with all leads, lifts etc.

Removing wooden or A.C. partition including frame work and stacking the materials as with all leads, lifts etc. complete.

Removing any kinds of debris including loading in truck and conveying to approved dumping point beyond MCGM limits, unloading, spreading etc. Complete with all leads and lifts.

Cutting down trees including trunk sand branches with girths above 30 cm to 60 cm and stacking the materials neatly with all lifts and lead as directed and earth filling in the depression / pit if any.

Cutting down trees including trunk sand branches with girths above 450 cm and stacking the materials neatly with all lifts and lead as directed and earth filling in the depression / pit if any.

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means.

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3m.) By Mechanical Means.

Excavation for foundation in hard murum and boulders including removing the excavated material upto a distance 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Liftupto 1.5m.) By Mechanical Means.

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metrs beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary backfilling with available earth/murum, ramming, watering including shoring and strutting etc. complete (Lift upto 1.5 m) By Mechanical Means.

Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift from 1.5 to 3m). By Mechanical Means

Providing pre constructional antitermite treatment as per S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyri fos per square meter surface area covering 10 years guarantee on requisite bond paper.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) treatment by treating the backfill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of clorophyrifos per square metre of vertical surface area covering 10 years guarantee on requisite bond paper. Spec.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on requisite bond paper.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on requisite bond paper.

Providing antitermite treatment to the wooden frames of doors/windows of the existing building as per I.S. 6313 (Part-III) by drilling 6mm dia. holes at four corners on one side and four corners on other side at a downward angle of about 45 degree at the junction of wood work and masonary and injecting 150 ml. of chlorodane 5% W.C. and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. (i) First Floor.

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15cm to 20cm including watering and compaction etc. Complete

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15cm to 20 cm thick including hand packing and compacting etc. complete.

Providing and laying cast in situ / Ready Mix Cement Concrete M-40 for bored piles each of load capacity and as per design and of 750 mm diameter or as directed placed through steel shells sunk to the required depth thrugh all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in-charge including placing with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement).

Providing and laying cast in situ / Ready Mix Cement Concrete M-40 for bored piles each of load capacity and as per design and of 900 mm diameter or as directed placed through steel shells sunk to the required depth thrugh all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in-charge including placing with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement).

Providing and laying cast in situ / Ready Mix Cement Concrete M-40 for bored piles each of load capacity and as per design and of 1050 mm diameter or as directed placed through steel shells sunk to the required depth thrugh all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in-charge including placing with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement).

Chiseling through pile shells in hard strata like boulders, soft and hard rocks Beyond 900 mm and up to and inclusive of 1050 mm dia. including removing and stacking the loose materials etc. complete and disposing of the unserviceable materials outside complete.

Carrying out load test for 1.5 times the proposed safe working load on the pile in driven position above 900 mm diameter including construction of test cap, use of accessories and instruments including providing graphs as per I.S. code or Std. Specifications and dismantling the test cap after testing and cleaning the site complete.

Carrying out low strain pile Integrity test on 750mm/900mm/1050mm diametre pile including all arrangement for test equipment /accessories materials submission of test report etc but excluding the cost of installation of job pile ( installation of pile shall be paid separately as per relevent items0 all completed as per specification and as directions by the Engineer in charges. (For 750 mm dia)

For 900 mm dia

For 1050 mm dia

Conducting routine vertical load test for 1.5 times safe load carrying capactiy by means of high strain Dynamic Load Test including provision and erection of crane hammer drop mechanism, acceleration and displacement velocity including excavation dewatering preparation of pile head including building up of pile additional reinforcement if any etc. all completed as per approved method (ASTM D4945-89) submission of test report specifications and instruction of the engineer for piles of following diameter (For 750 mm dia)

For 900 mm dia

For 1050 mm dia

Empty boring for 725 to 1050 mm dia. Bored R.C.C. cast in situ piles including withdrawal of shell, removal of earth to a distance of 50 metres etc. complete.

Chipping and dressing of the R.C.C. piles up to 0.60 meter including cleaning reinforcement and removal of dismantled materials up to a distance of 50 meter beyond the building area etc. for providing pile caps.

Providing placing and Driving in position 6 millimeter mild steel liner for R.C.C. Piles up to required depth with 12mm thick mild steel cutting edge of 0.50 m length at bottom including fabricating cutting the mild steel sheet to requied diameter and shape, welding the joints and driving with the help of required machineries including all materials labours and lifts etc. complete. (From 3.00 to 9.50 meter deep liner)

Supplying and spreading geofabric filter layer of Geotextile of Polypropylene multi filament woven to the line, level and grade with pore size less than 0.075 mm and permeability greater than 9.0 litre/sqm/second confirming specification IS : 1969 and ASTM standard including conveying to the site, joining and stitiching with proper overlap and laying at excavated surface in tidal condition as directed by Engineer in charges etc completed.

Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for foundation and bedding including steel centering, formwork, laying / pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc.)

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc.)

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap metal for R.C.C.pile caps as per detailed design sand drawings, including bailing out water manually, centering, formwork, laying/pumping, compacting, finishing and curing etc. with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Panmixer) etc. complete. With fine aggregate (Natural Sand/Crushed sand VSI Grade finely washed etc.) complete.(Excluding steel reinforcement)

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) (Ground Floor - Up to Plinth)

Ground Floor - Above Plinth

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction and roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) Ground Floor - Up to Plinth

Ground Floor - Above Plinth

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc.) Ground Floor

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap /granite/quartzite /gneiss metal for R.C.C. canopy as per detailed designs and drawing including per detailed formwork, laying/pumping compacing and roughening the surface if special finish is to be provided and curing etc complete (excluding reinforcement) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc complete with fine aggregate (Natural Sand/Crushed sand VSI Grade finely washed etc)

Providing and laying Cast in situ/Ready Mix cement concrete in M-40 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-40 of trap/ granite/ quartzite/ gneiss metal for R.C.C. coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting, curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-40 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying in situ cement concrete M-40 with tremix treatment for Concrete flooring is including laying plastic sheet for 125 micron thickness with groove cutting of 4 mm wide and 20 mm deep with necessary refilling with bitumen (excluding reinforcement) with coarse and fine aggregate (Natural sand/ VSI grade finely washed crushed sand) etc. complete.

Providing and fixing in position HCRM/CRS (Corrosion Resistant Steel) (Ground Floor - Up to Plinth)

Ground Floor - Above Plinth

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete.

Providing and constructing masonry in Autoclaved Areaclaved (Celluar) Concrete Block of aproved manufacturer confirming to IS 2185 Part III 1984 of size (600 x 200 x 200) mm in extra fine jointing mortar of fixoblock of Ultra Tech or equivalent in superstucture including,striking joints, racking out joints watering and scaffolding etc.complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and constructing masonry in Autoclaved Areaclaved (Celluar) Concrete Block of aproved manufacturer confirming to IS 2185 Part III 1984 of size (600 x 200 x 150) mm in extra fine jointing mortar of fixoblock of Ultra Tech or equivalent in half brick thick wall including 2 hoop iron strips 25mm x 1.6mm at every third course,properly bend and bonded at ends scaffolding racking out joints and watering compete. Spec. As directed by Engineer in Charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing Expansion joints in R.C.C. framed structure (exterior coloumns) with plain premoulded filler 25mm thick and 3mm thick alluminium plate, hold fast, fixing T.W. battens on internal face, finishing etc completed

Providing membrane waterproofing technology with APP / SBS membrane of 4mm to 3mm thick to floors and sanitary blocks along with India water proofing or alike consisting of one layer of B.B. coba of 5 cm to 7.5 cm thick in cement mortar 1:2 sandwiched between two layers of cement mortar 1:4, 20 mm thick mixed with water proofing compound, top finishing coat of cement slurry 6 to 12 mm thick with water proofing compound etc. complete with 32 mm dia. PVC pressure relief pipe of adequate length including waterproofing treatment to 30 cm height of wall in cement mortar 1:4 and covering 7 years guarantee on court fee stamp of Rs.100/- with ponding test including all lead, lift etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 sqm /kg with two coat using Dr. Fixit or alike of chemicals for masonry and concrete surface by brush covering 7 years guarantee on requisite Stamp Paper etc. complete.

Providing and laying jointless Polydee-LM, a highly flexible elastometric coating for RCC / cementitious surface for terrace waterproofing on B.B. Coba / R.C.C, after application of TP-42 Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM @ 700 gms/sqm and applying 2nd coat of Polydee-LM @ 700 gms/sqm and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms/sqm to be paid in separate item.) covering 7 years guarantee on requisite Stamp Paper etc. complete.

Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing for basement or underground floor on a base of Cement concrete 1:3:6, including sub base of 2.50 centimeter thick Cement mortar 1:3 with conceal, secrete (RMW), Algae proof or other alike waterproofing liquids, raking of joints upto 35 mm depth, filling the joints with 6 mm size crushed metal, hand grouting with cement slurry, curing and cleaning, with 7 years guarantee on requisite stamp paper with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete)

Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing treatment to vertical outside faces of Reinforced Cement concrete walls of basement or underground floor including filling the gap of 25 mm between rough shahabad and R.C.C. walls with cement grout mixed with water proofing liquid Algae proof or other alike with one tile lift method, brushing the joints horizontally with cement slurry mixed with water proofing liquid for width 30 to 35 mm and sloping coping over topmost tile with cement mortar 1:3, butting the bottom most with Cement concrete 1:2:4 mixed with water proofing liquid, curing, with 7 years guarantee on court fee stamp of Rs.100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete)

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:3 without neeru finish to concrete or brick surfaces, in all position including scaffolding and curing etc. complete. (Use Natural sand) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and applying gypsum plaster (with Gypsum material of Gypsum India / Mega Sign or equivalent make) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface (Excluding rough cast plaster) in all position including preparing and Finishing the surface scaffolding etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing sand faced plaster externally in cement mortar using approved screened sand,in all positions including base coat of 15mm thick in cement mortar 1:4 using waterproofing compound at 1kg percement bag curing the same for not less than 2 day sand keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc. complete. (Use Natural sand) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing fine cement finish 1.5 mm thick over green plaster surface including scaffolding curing etc completed Spec As director by Engineer in charges

Labour charges for providing groove in external plaster having width and spaced as directed by engineer incharge etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing chicken mesh of 24 gauge, with about 30cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete. Spec. As directed by Engineer in charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete. Spec. As directed by Engineer in charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying machine cut machine Polished Kota stone flooring 25mm to 30mm thick and required width in plain/ diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing in required position skirting or dado of polished Kotah Stone slab 25 mm to 30 mm thick fixed on base on plaster of cement mortar 1:4 including cement float, filling joints with cement slurry, curing rubbing, polishing and cleaning complete. Spec. As directed by Engineer in Charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing Mirror polishing to Kota Stone for flooring including using all necessary stones and equipments cleaning, washing etc. complete. Spec. As directed by Engineer in charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing Mirror polishing to Kota Stone for skirting including using all necessary stones and equipments cleaning, washing etc. complete. Spec. As directed by Engineer in charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. (Basic rate of Tile = Rs. 495/Sq.m. inclusive of all taxes transportaion, etc. complete.) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying ceramic tiles having size 30 cm. x 45 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. (Basic rate of Tile = Rs.516/Sq.m. inclusive of all taxes transportaion, etc. complete) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying vitrified mirror / glossy finish tiles decorative type premium double charged having size 600 x 600mm of 8 to 10mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. Spec. No.Bd.M.12 Page No.385

Providing and laying vitrified mirror / glossy finish tiles decorative type premium double charged having size 600 x 600mm of 8 to 10mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for skirting in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and laying in position flooring of Green Marble of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. (Basic rate of Green Marble = Rs. 990/Sq.m. inclusive of all taxes, polishing, transportation, etc. complete.) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing green marble of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing / moulding the sharp edges wherever necessary, curing, etc. complete.(Basic rate of Green Marble = Rs. 990/Sq.m. inclusive of all taxes, polishing, transportation, etc. complete.) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing machine cut machine polished 18 mm to 20 mm thick Green Marble for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. (Basic rate of Green Marble = Rs. 990/Sq.m. inclusive of all taxes, polishing, transportation, etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying in position flooring of Italian Marble of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. Spec. As directed by Engineer in charge. (Basic rate of Italian Marble = Rs. 3767.40/Sq.m. inclusive of all taxes, polishing, transportation etc. complete.) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying in position skirting of Italian Marble of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. (Basic rate of Italian Marble = Rs. 3767.40/Sq.m. inclusive of all taxes, polishing, transportation, etc. complete.) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying in position Antiskid flooring of Italian Marble of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. (Basic rate of Italian Marble = Rs. 3767.40/Sq.m. inclusive of all taxes, polishing, transportation, etc. complete.) (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying in position dado of Italian Marble of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. (Basic rate of Italian Marble = Rs. 3767.40/ Sq.m. inclusive of all taxes, polishing, transportation, etc. complete.) (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying cement concrete flooring 40mm thick with M20 cement concrete laid to proper level and slope in alternate bays, including compaction, filling joints, marking lines to give appearance of tiles of 30cm x 30cm or other size laid diagonally/square etc. finishing smooth (with extra cement) in any colour as directed and Curing etc. complete. With Crushed Sand.

Providing and laying in position Three Layers Parquet / Engineered Wooden Flooring having plank size of 135m,m to 210mm wide 1800 to 2420mm long of 15mm thick with approved veneer on top including all necessary jointing and core material as per detailed drawings & design etc completed

Providing Mirror polishing to Italian marble including using all necessary stones and equipements cleaning washing floor scrubbing marble stone with Single Disc Mirror Polishing using scrubbing pads then using floor polishing to remove dust & dirt & apply polish powder & single disc machine to make it shine and increase the gloss etc completed (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and applying three coats pearl/luster finish paint of approved colour and shade to the existing plaster surface including scaffolding preparing the surface applying the acrylic wall putti etc complete (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases (NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide and Absorbs CO2 (4.8 kg/15 l) plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufacturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete.

DGU structural glazing work - Supplying and installing semiunitized structural glazing have using 67mmx 81mmx3mm curtain wall alluminium section for mullion and trasom 38mmx38mm L angle for section joinery Saint gobain 6mm imperial blue + 12 mm air gap + 6mm low-e glass fixed on 68 mm x 28mm x 1.6mm shutter section with the help of 12mm spacer tape and dow corning silicon ss screw LT make ancor fastner and 75mmx 200mmx5mm ms bracket as per detailed drawing and design etc completed (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing false ceiling of 15mm thick Armstrong make as per drawings including powder coated G.I. wall angle of 20 mm x 20 mm x 0.60 mm size, G.I. grid runners of size 15 mm x 38 mm at 600 mm center to center both ways and suspended using G.I. 3 mm wire including fixing using butterfly clips and fasteners including transporting, scaffolding all necessary labour and machinery, finishing etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing false ceiling with eco-friendly light-weight calcium silicate tiles of spintone surface texture aerolite make or equivalent of size 595mm x 595mm having 15mm thick densified micro look edge and 100% humidity resistance incombustible as per BS 46part IV and thermal conductivity 0.043 w/m 0 KC and NRC 0.50 placed in true horizontal level suspended grid of size 600x600mm made from hot dipped G.I. steel sections ion silhouette profile, rotary stitched double webbed white with 6mm reveal profile (white/black), wherein, main T runner of size 42mmx14mm between main tee 600mm centertocenter and secondary cross T of size 33x14x0.43mm thick of length 600mm long spaced inter-locked at middle of the first crossed T in each panel to form grid of 1200mmx600mm resting on periphery wall Profile wall section 19mm (7+7) x 19mmx0.40thicknesses and laying false ceiling for services like diffusers grills including cutting, making opening for light fittings, fixtures, , smoke detectors etc., wherever required. Main T runners suspended from ceiling with using G.I. soffit cleats of size 25x35x1.6 mm of required length fixed to the ceiling with 6mm dia and 50mm long dash fastener, 4mm dia G.I. adjustable rods with powder-coated/good quality G.I. level adjustment clips of 35x35x0.8mm spaced @1200, center-to-center along main T all complete at all heights as per the specifications, drawings and as per the directions of Engineer in charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying Italian Marble of 18 to 20 mm thick for door frame / window boxing / Sills etc. on C.M. 1:6 including filling joints with polymer base filler nosing / chamfering the edges, Moulding / rounding, edge polish wherever necessary, curing, etc. complete. (Basic rate of Italian Marble = Rs. 3767.40/Sq.m. inclusive of all taxes, polishing, transportation, etc. complete.) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast with oil painting, etc. complete. Spec. As directed by Engineer in charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing solid core flush door in single / double leaf 35mm thick decorative type of exterior grade as per detailed drawing & design including approved mica face on both face (1.5mm thick), fittings, Brass oxidised fixtures (Aldrops, Handles, Tower bolts, Hinges) of approved make and size as specified in the drawing including all necessary beads, moulding, lipping, french polish etc. complete. (without door frame) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. a) Pull Handle (Neki PHA 2210) Satin or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. b) Door closer (Hyper) or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. c) Floor Door Stopper (Neki) (DST 1005) or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. d) Wall Door Catcher (SS Body) (Dorset) or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. e) Sign Plates (Neki EP 42) Satin or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. f) Square Handle (Neki PHS 2212) Satin or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. g) Door Knob (Neki) Satin (DNR 50) or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing Hardware of approved brand and make to doors as directed on drawing including all necessary fitting etc completed Mortise lock with handle (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing Hardware of approved brand and make to doors as directed on drawing including all necessary fitting etc completed Eye Hole (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing Hardware of approved brand and make to doors as directed on drawing including all necessary fitting etc completed Safety Chain (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. h) 16mm dia. & 450mm long Aldrop (CENT).or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. i) 12mm dia. & 350mm long Tadi patti. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. j) 450mm long tower bolt. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. k) 300mm long tower bolt. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing in position UPVC sliding doors of two tracks of fenesta make as per detailed drawings & design with pristine white colour slider of bugscreen no monsoon guard no mesh joint S65 PS1 slider sash S65 PS1 bug sash fibre mesh bug mesh BS midrail inside BS position normal BS midrail type slider treshold with treshold/118mm 1 no BS midrail C type BS handle aperture plaster finish white colour handle inner & outer track espag patio handle DG INS TGH (6T + 12 + 6T) as directed by Engineer in charges with all necessary UPVC sections fixtures and fastenings such as roller bearing in nylon casting ans self locking catch fitted in vertical section of shutter including 5mm thick plain glass and aluminium mosquito net shutter with stainless steel jali with all required screws and nut etc completed (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing in position UPVC sliding doors of three tracks of fenesta make as per detailed drawings & design with pristine white colour slider of bugscreen no monsoon guard no mesh joint S65 PS1 slider sash S65 PS1 bug sash fibre mesh bug mesh BS midrail inside BS position normal BS midrail type slider treshold with treshold/118mm 1 no BS midrail C type BS handle aperture plaster finish white colour handle inner & outer track espag patio handle DG INS TGH (6T + 12 + 6T) as directed by Engineer in charges with all necessary UPVC sections fixtures and fastenings such as roller bearing in nylon casting ans self locking catch fitted in vertical section of shutter including 5mm thick plain glass and aluminium mosquito net shutter with stainless steel jali with all required screws and nut etc completed (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing in position UPVC sliding windows/ ventilators two tracks of fenesta make as per detailed drawings & design with pristine white colour slider of bugscreen no monsoon guard no mesh joint S65 PS1 slider sash S65 PS1 bug sash fibre mesh bug mesh BS midrail inside BS position normal BS midrail type slider treshold with treshold/118mm 1 no BS midrail C type BS handle aperture plaster finish white colour handle inner & outer track espag patio handle DG INS TGH (6T + 12 + 6T) as directed by Engineer in charges with all necessary UPVC sections fixtures and fastenings such as roller bearing in nylon casting ans self locking catch fitted in vertical section of shutter including 5mm thick plain glass and aluminium mosquito net shutter with stainless steel jali with all required screws and nut etc completed (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing in position UPVC sliding windows/ ventilators three tracks of fenesta make as per detailed drawings & design with pristine white colour slider of bugscreen no monsoon guard no mesh joint S65 PS1 slider sash S65 PS1 bug sash fibre mesh bug mesh BS midrail inside BS position normal BS midrail type slider treshold with treshold/118mm 1 no BS midrail C type BS handle aperture plaster finish white colour handle inner & outer track espag patio handle DG INS TGH (6T + 12 + 6T) as directed by Engineer in charges with all necessary UPVC sections fixtures and fastenings such as roller bearing in nylon casting ans self locking catch fitted in vertical section of shutter including 5mm thick plain glass and aluminium mosquito net shutter with stainless steel jali with all required screws and nut etc completed (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing in position (as per I.S.1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90mm at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30mm at weight 1.070 kg/Rmt. Top and side track section 92 x 31.75 x 1.30mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25mm at weight 0.417 kg/Rmt. as per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5mm thick plain / opaque glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc., complete. With colour Anodising with box. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing fiber glass reinforced polyster door shutter 35 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing glass doors as per detailed drawings & design. Door shutters shall be consist of full height 10mm thick clear toughened float glass fixed in alluminium profile top, bottom & sides. All the edges of the glass shall be crystal polished. Item shall include 1 pair of brushed S. S. Handles - 32mm dia, 2030 mm height, Hinges and Miscellaneous hardware etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing full height glass partitions of 12mm thick clear toughened glass fixed in alluminium profile as per detailed drawing & design. Rate should be inclusive of all necessary hardware and labour required. Edges of to glass panels should be sealed with silicon sealant or glass adhesives, edges of glass should be machine polished, divisions of glass as per drawings etc. complete. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg/sqm as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and Fixing mat finish stainless steel of (302 grade) railing with top pipe of 50mm dia. and vertical pipe of 38mm dia at 0.60m c/c or as required and horizontal pipes of 25mm dia in three rows, all pipes of 2mm thick including buffing, fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75mm dia above newel post of 75mm dia meter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and laying cast iron pipes of B class of 75mm diameter with sockets and spigot ends/ flanges and cast centrifugally/vertically including specials, laying pipes and back filling the trench complete including excavation. (Ground Floor)

Providing and laying cast iron pipes of B class of 100mm diameter with sockets and spigot ends/ flanges and cast centrifugally/vertically including specials, laying pipes and back filling the trench complete including excavation. (Ground Floor)

Providing and fixing screw down for 25mm dia. C.P. wheeled stop tap of brass including necessary sockets/union nut complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing screw down for 32mm dia. C.P. wheeled stop tap of brass including necessary sockets/union nut complete. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing screw down for 50mm dia. C.P. wheeled stop tap of brass including necessary sockets/ union nut complete.

Providing and fixing screw down for 80mm dia. C.P. wheeled stop tap of brass including necessary sockets/ union nut complete.

Providing and fixing 45cm wide mild steel ladder of 40mm x 6mm mild steel flat stringers and steps of 18 mm dia. mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete. (Anti Corrosive Paint) (Seventh Floor)

Providing and fixing White Glazed Earthenware full stall type Urinal with flush valve with fitting, inlet pipes and stop tap, brackets for fixing, 32 mm dia. P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connection up to the outside face of the wall.

Providing and fixing white glazed earthenware Table top basin of 565 x 420 x 140 mm size including single lever basin mixer (Piller cock) without pop up waste with 450mm long braided hoses, Bottle trap (with internal partition) 32mm size with 300mm & 190mm long wall connection pipes & wall flange, exposed part kit of concealed stop cock & Flush cock with fitting sleeve, operating lever & adjustable wall flange with seal etc. complete. (Table Top Basin : Jaquar make KUS-WHT-35935, Piller cock : Jaquar make OPP-15011BPM, Bottle Trap : Jaquar make ALD-769L300x190, Concealed Stop Cock : Jaquar make OPP-15083KPM) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing white glazed earthenware wash hand basin of 55 cm x 40 cm size with Piller cock including brackets, rubber plugs and brass chain, stop tap, PVC bottle trap and necessary pipe connections including UPVC waste pipe and trap up to the out side face of the wall, making good the damaged surface, testing etc. complete. (Wash Basin : Jaquar make ECS-WHT-803, Bottle Trap : Jaquar make ALD-769L, Stop Cock – Jaquar make CON 53KN, Pillar Cock : Jaquar make CON-021KN)or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and constructing Italian Marble kitchen platform as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished Italian Marble 16 to 20 mm top with side strips of Italian marble at front and both sides of platform raised with two vertical Italian mable supports 15 cm height and top Italian marble of 75 x 40 cm including cutting, opening for sink of required size in kadappah as well as Italian marble etc. complete. (Basic rate of Italian Marble = Rs. 3767.40/Sq.m. inclusive of all taxes, polishing, transportaion, etc. complete.) (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and constructing Italian Marble platform for Table Top basin as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished Italian Marble 16 to 20 mm top with side strips of Italian marble at front and both sides of platform raised with two vertical Italian mable supports and top Italian marble including cutting etc. complete. (Basic rate of Italian Marble = Rs. 3767.40/Sq.m. inclusive of all taxes, polishing, transportaion, etc. complete.) (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing 30cm x 30cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap. (Ground Floor)

Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 60cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete. (Ground Floor)

Providing and constructing Brick Masonry Inspection Chamber 90cm x 90cm x 45cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete. (Ground Floor)

Providing and fixing Belgium mirror on 8mm thick waterproof ply with alluminium profile on all four edges as per detailed drawings & design etc. complete. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing, laying and fixing P.V.C. pipe of 50mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing, laying and fixing P.V.C. pipe of 80mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing Single towel rail 600mm long of Jaquar make including all accessories complete. (Towel rod : Jaquar make CAN-1111SM) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing Towel rack with lower hanger of Jaquar make including all accessories complete. . (Towel rack : Jaquar make AHS-1581) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing Towel ring round with round flange (Stainless steel) of Jaquar make including all accessories complete. (Towel ring : Jaquar make CAN-1121BN) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing chromium plated towel rod 16 mm dia and 75 cm. in length including all accessories complete. (Towel rod : Jaquar make AHS-1507 or equivalent) or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing chromium plated towel including all accessories complete. (Towel ring : Jaquar make CAN-CHR-1121BN or equivalent) or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing 40mm dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete. (Seventh Floor)

Providing and fixing in walls/ ceiling/ floor 15mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing in walls/ ceiling/ floor 25mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing in walls/ ceiling/ floor 32mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing in walls /ceiling/ floor 40mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete.

Providing and fixing in walls /ceiling/ floor 50mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete

Providing and fixing 10cm PVC nahani trap (Long arm) with grating etc. complete. (Nahani Trap Make : Jain / Supreme / Finolex or equivalent.) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete. (Make : Nirali) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing Angular stop cock with wall flange Jaquar make or equivalent continental including necessary sockets/union nut etc. complete. (Jaquar make OPP-15053PM) or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Two way BIB cock with Health faucet etc. complete. (2 way BIB cock : Jaquar make OPP15041PM, Health faucet : Jaquar make ALD-565) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing 15mm dia. Screw down 2 way C.P. BIB bib cock with Health faucet including necessary sockets, union nut etc. complete. (Two way BIB Cock : Jaquar make CON-041KN, Health Faucet : Jaquar make ALD-573). or equivalent as directed by the Engineer in-charge. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing single lever wall mixer 3 in 1 system with provision for both hand shower & over head shower with 115mm long bend pipe, connecting legs & wall flange with Hand shower 140mm round shape single flow with aur effect (ABS body & face plate chrome plated) with rubit cleaning system including Flexible tube 12mm dia. & 1.5m long with nuts and Wall outlet with shower hook in square shape, Over head shower 200x 200mm sqauare shape flow (ABS body chrome plated with gray face plate) with rubit cleaning system and fittings like socket union, nuts, bends, valves, reducers, including necessary drilling holes in walls, slabs etc and remaking good the demolished portion to restore the same in original condition neatly and cleaning the site after completion of work, testing etc. complete. charge. (Wall Mixer : Jaquar make OPP-15125PM, Hand shower : HSH-1727, Over head Shower : Jaquar make OHS-35497, Flex Tube : Jaquar make SHA-549D12, Shower hook : Jaquar make SHA-566S) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing chromium plated wall mixer cock of heavy duty without washer with chromium plated showers with/without telephonic arrangement including shower rose, necessary supply pipes 15 mm dia. and fittings like socket union, nuts, bends, valves, reducers, including necessary drilling holes in walls, slabs etc and remaking good the demolished portion to restore the same in original condition neatly and cleaning the site after completion of work, testing etc. complete. (Wall Mixer : Jaquar make CON-273NUPR or equivalent, Over Head shower : OHS 1989 or equivalent, Shower rose : Jaquar make 477 or equivalent). or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Bath tub of size 750 x 1700 x 470mm with PMMA sheet, PU green reinforcement, SS frame, safety vaccum breaker, keypad control, overflow with drawin & filler, 1.4 HP water pump, slim water & back jets, 0.9 HP air blower, Air jets & regulatoir, headrests etc., Hand shower 140mm round shape single flow with aur effect (ABS body & face plate chrome plated) with rubit cleaning system including Flexible tube 12mm dia. & 1.5m long with nuts, Bath tub filler consisting of 2 controls cocks and one spout of 20mm cartridge size including fittings, necessary drilling holes in walls etc. and remaking good the demolished portion to restore the same in original condition neatly and cleaning the site after completion of work, testing etc. complete. (Bath tub : Jaquar make JWP-WHT-ALIVE180CX, Hand shower : HSH-1727, Flex Tube : Jaquar make SHA-549D12, Bath tub filler : Jaquar make FLR-CHR-5095N) or equivalent as directed by the Engineer in-charge. (First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing BIB cock with wall flange of Jaquar make including necessary sockets/ union nut etc. complete. (Jaquar make OPP-15037PM)or equivalent as directed by the Engineer in-charge. First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing C.P. BIB cock with wall flange jaquar or equivalent make continental (CAT.NO. CON047) including necessary sockets/ union nut etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing single lever sink mixer with swinging spout (Table mounted) with 450mm long braided hoses of Jaquar make including necessary sockets/ union nut etc. complete. (Jaquar make OPP-15173BPM) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing in position Wall hung WC with UF soft close slim seat cover, Hinges, accessories set, of size 360 x 500 x 380mm, Single piece slim concealed cistern with floor mounting frame, installation kit & S type drain pipe connection set for wall hung WC without flush control plate, etc. complete. (Wall Hung WC with seat cover : Jaquar make LYS-WHT-38951SM, Concealed cistern : Jaquar make JCS-WHT-2400FS, Flush control panel : Jaquar make JCP-CHR-852415) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Paper holder with flap etc. complete. . (Paper Holder : Jaquar make AHS-1553) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing in position European type White glazed earthen ware Wall Hung type water closet, Back inlet, 'P' trap C. I. bracket with C.P. bolt, matching seat cover & fixing concealed type C.P. flush valve with 32mm size control cock & required length operating lever assembly & connecting its outlet to the W.C. pan testing etc. complete. (Prior approval of sample by Ex. Engineer is necessary before use.) (Wall Hung W.C. : Jaquar make ECS-WHT-955S/N or equivalent, Seat cover : Jaquar make CNS-WST-WCS1 or equivalent, Flush Valve Make - Jaquar FLV-1085KN or equivalent.) (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and fixing in position UPVC ultra violet stabilized 110mm outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etc. complete.

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Soap Dish holder of Jaquar make etc. complete. (Soap dish holder : Jaquar make CAN-1131N) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Soap Dish holder etc. complete. (Soap dish holder : Jaquar make CAN-CHR-1131N ) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing & fixing Tumbler holder of Jaquar make etc. complete. (Tumbler holder : Jaquar make CAN-1141N) or equivalent as directed by the Engineer in-charge. (First Floor)

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Provind & fixing 40mm Strainer etc. complete.

Provind & fixing 80mm Strainer etc. complete.

Providing and laying 100mm dia salt glazed stoneware pipe including fittings such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

Providing and laying for 150mm dia salt glazed stoneware pipe including fittings Such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

Providing, hoisting and fixing in position CI Manhole frame & cover of best quality and of required size and shape with locking arrangements including applying two coats of anti-corrosive paints etc. complete. (Seventh Floor)

Providing and fixing matt finish Stainless Steel Lettering (full & half letters) of various heights including material, labour, cleaning etc. complete. Note: Height of Letters 30 cm.

Providing and fixing Brass Individual Quarter Number Plate to each quarter as per desing and drawing or as directed by Engineer-in-charge etc. complete.

Providing and fixing colour coated, wall mounted metal letter box with locking arrangement as per design and drawing or as directed by Engineer in charge etc. complete.

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works. (Ground Floor)

First Floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Seventh Floor

Providing and making Kitchen cabinets etc. complete. Trolleys Below Existing platform : 1) Frame : BWR Grade plywood verticals 2) Baskets : Tandem Drawer – 4 Nos. + SS Thali Basket 1 No. 3) Sliders : Grass Make grey finish 6 Nos. & Telescopic soft close 4) Hinges : Hafele make Soft close 5) Cutlery PVC tray – 1 No. 6) Magic Corner – Signet make 7) 3” Civil Skirting Shutter for platform : Wall Unit : - Ht : 24" 18mm commercial plywood box, externally & internally laminated Handles : G-section & Handle less for wall unit.

Providing & making cupboards / wardrobes etc. complete. (For Bedroom No.1) Wardrobe : Laminated 1) Wardrobe (Size : 5'3” x 2'0" x 7'0"Ht.) Swing shutter in 18mm thick Commercial Plywood externally Laminated & internally White Laminated. 2) Loft above Wardrobe (Size : 5'3” x 2'0" x 2'0"Ht.) with top openable Hydrillyc shutter in 18mm thick Commercial Plywood externally Laminated & internally White Laminated

Providing & making cupboards / wardrobes etc .complete. (For Bedroom No.2) Wardrobe : Laminated Wardrobe (Size : 6'2”x 2'0" x 7'0"Ht.) Swing shutter in 18mm thick Commercial Plywood externally Laminated & internally White Laminated

Providing & making cupboards / wardrobes etc .complete. (For Bedroom No.3) Master Bedroom : Laminated Wardrobe (Size : 5'10”x 2'0" x 7'0"Ht.) Swing shutter in 18mm thick Commercial Plywood externally Laminated & internally White Laminated

Providing, fabricating and erecting at site of work the tubular steel structure as per standard design and specifications having various spans in between trusses and in multiples of standard length of bays as specified as per standard specifications, inclusive of cost of steel tubular trusses, tubular columns purlins, tie runners, foundation bolts, base plates, nuts and bolts, welding wherever required etc. as per detailed drawing inclusive of one coat of anticorrosive paint and two coats of oil painting of approved quality and shade complete.

Providing & fixing Bottom guide wheels etc. complete.

Providing & fixing M.S. Hinges etc. complete.

Providing & fixing 300mm long and 16 mm dia M.S. Aldrop etc. complete.

Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete.

Providing and laying in position Noise barrier of approved shade including outside sheet plain aluminium alloy sheet 1.2mm thick inside sheet (Traffic/source side) Skin 1.2mm thick Aluminium alloy perforated sheet with 42% open area with 5mm hole Approx 12.5kg/Sq.m acoustic material polyester fiber, in two layers of 50mm thick density 60 kg/m3 Each panel having tone & groove to joint perfectly with each other, The panel and structure having gaskets at the joint ot block noise leakage. The Struture is of H profile in which acoustic panel slides lingitudinally Top Cover all acoustic panel covered at top with top cover made of alluminium alloy riveted to panel Powder coated the minimum thickness is 60 Mu. The STC rating is 36. etc. completed

Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing cast in situ/ready mix block of M10 cement concrete with circular or other shaped opening for water way including necessary formwork,compaction,finishing and curing etc.complete.(with reversible drum type mixer/concrete batch mix plant(panmixer) with SCADA with fine agreegates of required specifications (Natural sand / VSI sand finely washed etc.), cement 4.05 bags/cumt)

Providing and fixing Ductile iron man hole cover/ Strom Water Grating and Grating with frame of Various sizes,weight and types and loadbearing capacity as per EN-124,equivalent NECO with prior approval of concerned Superitending Engineer.

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader/ Paver on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. By Mix in Place Method and Grading - III Material. .

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with Vibratory roller. to the required density. By Mechanical Means. Grading I (Using Screening Type A (13.2) mm Aggregate)

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. By Mechanical Means. Grading II (Using Screening Type B (11.2 mm) Aggregate)

Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete.

Construction of dry lean cement concrete Sub-base over a prepared sub-grade with coarse and fine aggregate (natural sand/VSI grade finely washed crushed sand) conforming to IS:383, the size of coarse aggregate not exceeding 25 mm,cement content not to be less than 150 kg/cum,optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7days, mixed in a batching plant / Weigh batch mixer,transported to site with all leads and lifts,laid with a paver with electronic sensor/by suitable means as approved by Engineer-in-charge ,compacting with vibratory roller,finishing,curing and including preparation of sub-grade surface if required etc. complete.

Providing and laying in situ cement concrete M-40 with tremix treatment for 300 mm thickness for Concrete Road is including laying plastic sheet for 125 micron thickness with groove cutting of 4 mm wide and 20 mm deep with necessary refilling with bitumen (excluding reinforcement) with coarse and fine aggregate (Natural sand/ VSI grade finely washed crushed sand) etc. complete.

Providing and casting in situ or precast tapering R.C.C.M-20 Kerb without gutter (as per IRC 861983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M.1:2,setting the same in C.M.1:2 , including the required excavation in any strata and removing the excavated stuff anywhere in city and re doing the surface as specified and directed by Engineering In-charge.Using Concrete Batching and Mixing Plant

Supplying, filling, spreading & leveling sand in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer in charge.

Providing and fixing screw down for 50mm dia. C.P. wheeled stop tap of brass including necessary sockets/union nut complete.

Providing and laying in trenches 50mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 6.33 kg/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in trenches 80mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 10.15 kg/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec. No.Bd.V.5 Page No. 551.

Providing 80 mm double flanged short body pattern type manually operated Butterfly Valve having body, disc and end cover in graded cast iron to IS-210 Gr.CF 200 generally confirming to IS-13095-1991, Synthetic rubber faced ring secured on disc by retaining ring with stainless steel screw stub shaft of stainless steel riding in teflon bearing including inspection charges, transportation up to departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. excluding C.C. foundation /structural steel support. Butterfly valve-PN-1 (With by pass arrangement)

Providing and supplying 40 mm Air Valves as per IS-14845-2000 and MJP’s standard specifications of approved make and quality of following diameters including railway freight, inspection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores, unloding and stacking excluding GST levied by GOI & GOM in all respect etc. complete. Air Valve Single Ball Flanged / Screwed Type - PN -1

Providing and supplying 25 mm Air Valves as per IS-14845-2000 and MJP’s standard specifications of approved make and quality of following diameters including railway freight, inspection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores, unloding and stacking excluding GST levied by GOI & GOM in all respect etc. complete. Air Valve Single Ball Flanged / Screwed Type - PN -1

Providing and supplying 80mm strainer etc. complete.

Providing and supplying ISI mark CI D/F reflux valves (non-return valves) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental stores, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete. Reflux valves as per I.S.5312 Part I (1984) a) Without by pass arrangement - PN -1 i) 50 mm.

Providing and supplying ISI mark CI D/F reflux valves (non-return valves) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental stores, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete. Reflux valves as per I.S.5312 Part I (1984) a) Without by pass arrangement - PN -1 vi) 80 mm.

Providing, laying and fixing P.V.C. pipe of 50mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 75mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete.

Providing 75 mm double flanged short body pattern type manually operated Butterfly Valve having body, disc and end cover in graded cast iron to IS-210 Gr.CF 200 generally confirming to IS-13095-1991, Synthetic rubber faced ring secured on disc by retaining ring with stainless steel screw stub shaft of stainless steel riding in teflon bearing including inspection charges, transportation up to departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. excluding C.C. foundation /structural steel support. Butterfly valve-PN-1 (With by pass arrangement)

Providing and supplying 50 mm Air Valves as per IS-14845-2000 and MJP’s standard specifications of approved make and quality of following diameters including railway freight, inspection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores, unloding and stacking excluding GST levied by GOI & GOM in all respect etc. complete. Air Valve Single Ball Flanged / Screwed Type - PN -1

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well-casing pipe of 200mm dia,conforming to IS:12818, including required hire and labour charges,fittings & accessories etc. all complete, for all depths, as per the direction of Engineer in charge.

Supplying, filling, spreading & leveling coarse fine aggregate (Natural sand/crushed sand VSI grade finely washed etc.) of size range 1.5mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer in charge.

Supplying, filling, spreading & leveling stone boulders of size range 5cm to 20cm in recharge pit, in the required thickness, for all leads & lifts, all complete as per the direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge.

Providing and fixing 350 x 350 mm Mild Steel grating to opening in the harvesting pit and chamber etc. complete.

Providing and fixing RCC Chamber Cover with Grating for chamber size 600 x 600 mm with necessary frame etc. complete.

Providing and fixing Ductile iron manhole cover of heavy duty with frame of any size over inspection chamber etc. complete.

Boring/drilling bore well of 300mm dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools,plants & machinery required for the job, all complete as per direction of Engineer in charge, upto 90m depth below ground level.as directed by Engineer in charge

Providing & fixing Air vent for Ground Storage Reservoir etc. complete.

Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing 600mm dia. RCC Chamber cover with necessary arrangement etc. complete

Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete.

Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete.

Providing double flange sluice valve 150 mm dia, confirming for IS-14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete.. a) Sluice valves - PN -1 without bypass arrangement. vi) 150 mm.

Supply of Cast Iron Mechanical Compression Flanged / Socket Tailpiece (Popularly known as I TM Flanged / Socket Tailpiece) suitable for making flanged connection with the plain barrel of Cast Iron Spun Pipes ( as per - IS - 1536 /2001) and D. I. Pipes (as per IS: 8329 / 2000).The Tailpiec to be supplied complete with sealing rubber gasket of S.B.R, Cast Iron Follower Glands and M.S. Nut Bolts.The whole assembly should be mechanically and hydraulically tested to the provisions as laid down in IS:1538 /1993. The rates are inclusive of cost of material, freight charges, loading, transportation and unloading at departemental store, excluding GST levied by GoI and GoM in all respect etc. complete as directed..(150mm)

Providing & fixing Mild Steel openable shutter over Manhole (Cover size 900 x 900 mm) including necessary accessories etc. complete as directed by Engineer in-charge.

Providing & fixing Mild Steel openable shutter over Manhole (Cover size 900 x 450 mm) including necessary accessories etc. complete as directed by Engineer in-charge.

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & laying HMS PVC conduit mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying and erecting UPVC reinforced flexible conduit 31/32 mm in dia. conforming to I.S. with required number of couplings, PVC bushes, check nuts etc. complete.

Supplying & erecting mains with 2x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying & erecting mains with 1x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying & erecting mains with 2x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying & erecting mains with 1x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying & erecting mains with 2x4 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying & erecting mains with 2x6 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying & erecting mains with 4x16 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI marked modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type bell indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type buzzer 220 / 250V, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete. Note: Add Rs 57/- for additional two module box with double mounting plate if required.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 2 modules duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 modules duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 modules duly erected.

Point wiring for light/fan/bell concealed type in min 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm. (2+1E) FR grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW

Wiring for plug on board with Switch socket concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Supplying & erecting telephone copper cable 2 pair with 0.5 mm dia. laid in provided PVC casing capping/ conduit as per specification No. WG-TW

Supplying & installing co-axial copper cable low voltage grade RG-11 as per specification No. WG-TW

Supplying and erecting square shaped CRCA /die-cast aluminium powder coated housing LED panel light (slim edge-lit) suitable for upto 8 W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying & erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.

Supplying and erecting bulkhead fitting suitable for upto LED upto 12W fixed on wall. As per specification no. FG-IDF/BHF

Supplying and erecting bakelite call bell with 6 cm / buzzer with double coil suitable for 230V complete erected on PVC block.

Supplying and erecting ding dong / electronic musical type call bell with heavy duty coil suitable to operate on 230V A.C. supply erected on polished double wooden block/sunmica block of suitable size

Supplying & erecting 0.5W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying & erecting 3W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying & erecting 5W-7W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying and erecting regular/ standard model ceiling fan of 900 /1050 mm. sweep complete erected in position as per specification no. FG-FN/CF

Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 300mm. 1400 RPM rust proof body & blades, wire mesh, duly erected in an approved manner.

Supplying and erecting five star rated energy saving Ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original.

Supplying and erecting storage / pressure type horizontal / vertical water heater 25 litres with BEE 5 star rating of mild steel body, on wall / loft complete duly tested and marking sr. no. and date of erection. specification no. AP-WH/STWH

Supplying, installing, testing and commissioning split type variable speed Inverter technology room Air conditioning unit 1.5 TR capacity having ISEER minimum 4.50 suitable to operate on250V, 50 cycles, A.C. supply having 1 no of air handling unit hiwall

Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 6A to 32A, C- series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 6A to 32A in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SPMCB of 24 ways, on iron/ GI frame/wooden board.(horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 6 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Supplying & erecting original 1.25 mm CRCA sheet metal enclosures with 20A. 2 pin plug & earth socket and 20A. 3 pin plug top with 20A/30A single pole MCB complete erected on angle iron/ GI frame.

Supplying & erecting CRCA sheet metal one way enclosures suitable for DP MCB /TP MCB /FP MCB erected on angle iron/GI frame complete.

Providing & erecting 4 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB

Providing & erecting 4 Pole MCCB of 315/400A, 415V capacity with short circuit rating 36 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contac

Supplying, fixing and commissioning 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 63A as per specification no SW- RCCB/RCBO

Providing & erecting floor / wall mounting, MCCB panel board with door suitable for four pole incoming 400 A, 6 ways four pole outgoing upto 100 A MCCB's on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCB'S)

Providing & erecting incoming and outgoing cable alleys suitable for MCCB panel board with door of 250A incoming and 6 way outgoing or 400A incoming and 4 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated part

Supplying, erecting & terminating XLPE armoured cable 4 core 16 sq. mm. copper conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification

Supplying, erecting & terminating XLPE armoured cable 4 core 70 sq. mm. copper conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification no. EA-EP

Royalty charges to be reimbursed to the contractor after producing original receipt of payment made to the concern Govt. office as royalty charges for the material used for this work.

Carrying out Basic Test of Cement such as standard Consistency, Fineness, Specific Gravity, Setting Time (Initial & Final) Compressive Strength, Soundness in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Aggregate such as water Absorption, Specific Gravity, Impact Value, Crushing Value, in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Aggregate such as Sieve Analysis in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Aggregate such as Abrasion Value in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Aggregate such as Flakiness index & Elongation Index in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Aggregate such as Soundness in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Fine Aggregate such as Fineness Modulus (Sieve Analysis), Silt & Clay Content in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Fine Aggregate such as Silt Factor in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Bricks such as Water Absorption 9Set of 5 Bricks), Compressive Strength (Set of 5 Bricks), Efflorescence (set of 5 Bricks) in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Ceramic , Vitrified Tiles / Green, Italian Marble such as Water Absorption Modulus of Rupture (Set of 6 Tiles) in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Concrete such as Compressive Strength of C.C. Cube (Set of 3 cubes) in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Concrete such as Concrete Mix Design in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Concrete such as Permeability Test in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Mortar such as Compressive Strength (Set of 3 Cubes) in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Soil / Murum such as Liquid limit & Plastic Limit in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Soil / Murum such as Compaction Test (Proctor Density) in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Hollow / Solid / AAC Blocks such as Density Test (Set of 3 Blocks) Compressive Strength. (Set of 3 Blocks) Water absorption Test (Set of 3 Blocks) in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Water such as PH Value, Sulphate & Chloride Content in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Wood such as Density, Moisture Content in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of Flush door such as Knife Test, Adhesion Test, End Immersion Test in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Basic Test of PVC/CPVC/UPVC Pipes such as Weight per running meter, Diameter of pipe & wall thickness of pipe in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc completed

Carrying out Tensile Strength, % elongation Yield Stress, Weight per metre, Bend/Rebend test, Proof Stress and nitrol solution test on Steel Bar Upto 16mm diameter (Set of 3 Bars) in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Carrying out Tensile Strength, % elongation Yield Stress, Weight per metre, Bend/Rebend test, Proof Stress and nitrol solution test on Steel Bar above 16 mm diameter (Set of 3 bars) in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed