REPAIR REPLACEMENT OF TILING JOINERY PLUMBING AND SANITARY FITTINGS INCLUDING PETTY REPAIRS TO BLDGS OF TRANSIT CAMP AND NEAR BY UNITS UNDER GE 865 EWS

Amount

Demolition of cement concrete in ground floor and pavings n'exc 15cm thick below or above ground level complete all as specified and as directed

Demolition of cement concrete in any description and any position not otherwise specifically provided for.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for all as specified and as directed

Dismantling floor, hearth or wall tiling including wall cement mortar, bedding (But not backing ) and rubbish of premises complete all as directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc.laid bedded and pointed in any mortar.

Demolition of bricks (laid flat or on edge) or interlocking tiles in floors, channels, kerbes, aprons, etc laid dry of laid dry and pointed.

Demolition of precast concrete block /sone walling built in cement mortar including all quoins, arches , pillars etc all as specified and as directed

Taking down cement plaster / raised pointing on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc. complete all as specified and as directed

Material & Labour 75mm thick PCC 1:3:6 type C1 (using 20mm graded crushed stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement complete all as specified and as directed.

M&L forming contraction (Dummy) joints 50 mm deep x 10mm wide for plinth protection & similar work , filled with sealing compound Grade 'A' in plinth protection

M & L for 100 mm PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in floor of hard standing finished even and smooth with out using extra cement all as specified..

M&L Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in floor surface of hard standing .

M & L for 75mm PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in sub base of floor all as specified..

M&L for vitrified ceramic tiles 10mm thick (light shade ) (square/rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and screed bed with CM (1:4) 15mm thick for laying floor tiles all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.11Sqm and n.exc 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the screed bed with CM (1:4) 15mm thick laying floor tiles complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 and n.exc 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the screed bed with CM (1:4) 15mm thick laying floor tiles complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for Glazed ceramic coloured tiles in vertical surfaces 300 x 200 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match over 10mm thick CM (1:3) in dado/skirting tiles complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for Glazed ceramic coloured tiles in vertical surfaces 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match over 10mm thick CM (1:3) in dado/skirting tiles complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as mass concrete and filling of foundation all as specified and drected.

M&L dressed granite or trap stone as in Kerb stones roughly squared stones of size 20cm x 30 cm, so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in CM 1:6 and struck finish ( rate included for removal of old damaged kerb stones of any description).

M&L for cement concrete 1:5:10 type E-2, (40mm graded crushed stone aggregate) 100 mm thick as in sub-floors, sub-bases, floors and pavings,etc..

M&L PCC 1:2:4, 75 mm thick type B1 using 20mm graded crushed stone aggregate as in floor finished even and fair with out using extra cement complete all as directed by Engr-in-charge.

Machine pressed / vibro mechenically floated interlocking cement paver block ISI marked, any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 Grade, with topping of grey cement and pigment, laid over and including 50mm thick sand cushioning complete. Shape pattern of laying shall be approved by Engineer-in-charge. Make: NTC/NITCO/ULTRA /JOHNSON

M&L for cement concrete 1:4:8 type D-1 (20mm graded crushed stone aggregate) 75 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc complete all as specified and as directed.

M&L 40 mm thick PCC 1:2:4, type B1 using 20mm graded crushed stone aggregate as in floor finished even and fair with out using extra cement complete all as directed by Engr-in-Charge.

M&L for cement concrete 1:4:8 type B-2, (40mm graded crushed stone aggregate) 100 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc complete all as specified and as directed.

M&L for Chequred cement concrete tiles 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments laid over and including 20mm thick cement screed base (1:4) and all as directed by Engr-in -Charge. Make: NTC/NITCO/ULTRA /JOHNSON

Precast cement concrete 1:2:4, type B1 using 20 mm graded crushed stone aggregate, as in post , boundary pillars , pier caps, bollards and similar articles set in cement mortar 1:6 complete all as specified and as directed.

M&L TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-Charge.

All as per item No 29 above but 6 to 8mm dia as in stirups

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid over and including 20 mm thick cement screed bed in CM 1:3 complete all as specified and as directed.

Dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and as directed

Dismantlng framed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc under 40 Sq.cm in secton.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and n exc 25 sqcm in section.complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn as in beeding for edges of Ceiling ,lining ,or wooden flooring work fixed with nails exc 6 sqcm and n exc 13 sqcm in section.complete all as specified and as directed.

M&L for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and as directed

9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in wall paneling, shelves, boarding complete all as specified and as directed by Engr-in-Charge. MAKE: NOVA PAN/GREEN PLY BHUTAN BOARD/MYSORE WOOD BOARD/CENTURY PLYWOOD

All as per item No 37.00 above but on ceiling complete all as specified and as directed MAKE: NOVA PAN/GREEN PLY BHUTAN BOARD/MYSORE WOOD BOARD/CENTURY PLYWOOD

S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs all as specified and as directed by Engr-in-Charge.

M&L 7mm thick printed PVC sheet in strips & channel feathered at edges for fixing on solid PVC wall lining, insulated PVC wall lining and solid PVC partition inclusive of solvent cement and fixing at site as per specifications and as directed by Engr-In-Charge

S&F 5mm thik PVC sheet fillets of width 35mm for wall panelling inclusive of fixing on wall to make PVC frame as per specification and drawing.

M&L French polishing on wood or wood based surface of any width or girth or any description,including cleaning and preparing the surface including a coat of wood filler on old surface with two or more coats complete all as specified and as directed.

Dismantling boarding /wooden flooring of any description ,fixed in any positon

M&L for hard wood 2nd class factory made wooden boarded floors 25mm thick and skirtings planed one side & edges tonged and grooved or rebated , including backing with thermocol sheets or as specified by manufacture all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. ), complete all as specified and directed by Engineer-in Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. ), complete all as specified and directed by Engineer-in Charge.

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each complete all as directed by Engr-in-charge.

Taking down shutters of any description area not exceeding 1 Sqm each complete all as directed by Engr-in-charge.

Hacking old broken glass (any thickness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and as directed .

Taking down shutters of any description area not exceeding 1 Sqm each, resecuring or easing & adjusting and refixing in the same opening complete all as directed by Engr-in-charge.

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each, resecuring or easing & adjusting and refixing in the same opening complete all as directed by Engr-in-charge.

Anodised aluminium frame for doors, windows, ventilators and partition with one or more rebates including joining cleat for fixing etc., section 100 x 44.50 mm made from 1.50 mm thick aluminium powder coated (minimum 50 micron thickness) complete all as specified and as directed by Engineer-in-Charge. Make: JINDAL/INDAL/HINDALCO

S&F Anodised aluminium powder coated (minimum 50 micron thickness) window and ventilatior shutters, side hung type without sash bars aluminium sections weighting 0.55 by/m including necessary joining cleats, glazing clips rubber packing anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150 mm long (01 No) hinge type B-21 100 mm long (02 No) suitable handle (01 No) complete all as specified. Make: JINDAL/INDAL/HINDALCO

Anodised aluminium powder coated (minimum 50 micron thickness) door shutters, fixed type with sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodized aluminium fittings such as 150mm long (4 Nos) hinges, 200mm long (2 Nos) suitable handles, 250 mm long aluminium Tower bolt (01 No), 140mm long aluminium door stopper 01 No and aluminium snap beading, screws, etc. complete all as specified and as directed. Make: JINDAL/INDAL/HINDALCO

Pressed steel frames for doors, made out of 1.25 mm thick MS sheet, with one or more rebates including supply and fixing of necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 105 mm x 60 mm, including one shop coat of red oxide zinc chrome primer, including bottom of each chowkat to be welded with and including 25 x 3 mm thick flat iron projecting 10 cm on either side and back filling to chowkats with PCC 1:3:6 type C-0 using 12.5 mm graded crushed stone aggregates after applying and including one coat of black paint to prevent from corrosion complete all as specified and as directed by Engr-in-Charge. MAKE: M/S AGEW STEEL MANUFACTURE PVT LTD AHMEDABAD / M/S SHIV MULARA NARODA AHMEDABAD / GODREJ AND BOYCE MFG MUMBAI / SEN HARVIC MUMBAI / SHIVAM STEEL JAMMU

S&F 2nd class soft wood plain, solid, straight chowkets and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete(Glass shall be measured Seperately) all as directed by Engr-in-Charge.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete all as specified and as directed by the Engr-in-Chage

M&L for treating wooden chowkats surface of any description n exc 10 cm in width or girth with black bituminus paint in two coats.

M&L for preparing and treating small articles of builders hardware such as MS hold fasts ,MS but hinges etc, with two coats of synthetic enamal paint over a coat of primer when un connected with other paintings or when painted in adefferent tint.

Material & labour PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in bed blocks for hold fast, and the like complete all as specified and as directed by the Engr-in-Charge.

Factory made 35mm thick IInd Class Hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed by Engineer-in-Charge. MAKE: M/S WOOD PRODUCT INDORE/M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI/ M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT/M/S PIONEER TIMBER PRODUCT CHANDIGARH/M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU/M/S M.S JOINERY WORKS, PARIMPORA, SRINAGAR

40 mm thick flush shutters, solid core construction, with block board core and plywood face pannels and one face is covered with decorative face veneer with 4mm thick teak wood beading all around the edges to match, complete all as specified and directed by Engineer-in charge. M/S WOOD PRODUCT INDORE / M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI / M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT / M/S PIONEER TIMBER PRODUCT CHANDIGARH / M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU/M/S M.S JOINERY WORKS, PARIMPORA, SRINAGAR

35mm thick, factory made 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete, all as specified and directed by Engr in Charge. M/S WOOD PRODUCT INDORE M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT M/S PIONEER TIMBER PRODUCT CHANDIGARH M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU M/s M.S JOINERY WORKS, PARIMPORA, SRINAGAR

S&F MS framed work such as grills, gratings etc with ends of bars shouldered and/or rivited or forged into spikes, framed guard bars, barred iron doors, ladders framed balsters walk ways railings frame work of water tanks and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed.

M&L sheet glass 3mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed. Make : Modi Guard/Saint Gobin/Swastik

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples.

S&F in repairs Galvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples.

S&F mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section, ISI marked complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized ISI marked complete all as specified and as directed.

S&F stainless steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.

S&F mild steel butt hinges, medium weight cold rolled 75mm size complete all as specified and as directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section ISI marked complete all as specified and as directed.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodized ISI marked complete all as specified and as directed.

S&F in repair 300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F in repair 250mm long aluminium alloy, anodized, ISI marked, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed

M&L pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonery exc 10cm in width with solid block masonery with solid blocks,exc.10cm in width and setting in cement mortar 1:6 all as Specified

All as item No 78 but except blocks.

M&L for 15mm thick rendering on other than fair faces of brick works or stone masonary surfaces, in two layers 10 mm & 5 mm thick using water proofing admixture for outer layer of 5mm thick finished even and smooth without using extra cement in cement mortar 1:4 complete all as specified and as directed Note : Supply of liquid water proofing admixture shall be measured and paid separately under relevant item of this BOQ.

M&L for 10mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 6 complete all as specified and as directed

Supply only integral Water Proofing Admixture complete all as specified and directed. Make : Pidilite/Dr Fixit

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge. MAKE: SINTEX/POLYWELL/ROTEX/POLYCON

Rotational moulded polyethylene water storage PUF tank, PUF insulated with 75 mm thick PUF insulation of density not less than 48Kg/Cum, inner and out white, two layers, ISI marked (cylinderical vertical/rectangular/loft type with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge. MAKE: SINTEX/POLYWELL/ROTEX/POLYCON

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge. MAKE: SINTEX/POLYWELL/ROTEX/POLYCON

Rotational moulded polyethylene water storage PUF tank, PUF insulated with 75 mm thick PUF insulation of density not less than 48Kg/Cum, inner and out white, two layers, ISI marked (cylinderical vertical/rectangular/loft type with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge. MAKE: SINTEX/POLYWELL/ROTEX/POLYCON

25mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gram), fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. Make: Prayag/Polytuf/Supreme

15mm bore bib tap, (minmum weight 350 gms), chromium plated, fancy type, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule, fixed in repair complete all as specified and directed by Engineer-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA

15mm bore pillar tap cast copper alloy chromium plated screwed downhigh pressure, with or without lettered 'hot or cold' with long screwed shanks and fly-nuts screwed for iron pipe, fixed in repairs, complete all as specified and directed by Engineer-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA

Chromium plated, fancy type stop valve/cock, with long shank and cup, concealed type, cast copper alloy, screwed down, high pressure with handle, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, fixed in repairs complete all as specified. MAKE: PARKO/MARC/ESS ESS/CERA

All as per item No 90 above but angle stop valves. MAKE: PARKO/MARC/ESS ESS/CERA

S & F in repairs 750 mm long, 32 mm dia., PVC flexible Waste pipe for sinks /wash hand basins.

S & F in repairs 750 mm long, 40 mm dia., PVC flexible Waste pipe for sinks /wash hand basins.

Waste coupling of PTMT (half or full threaded), 32mm bore dia of discharge pipe (Minimum weight 32mm-45gms/40mm-60 gms) fixed in repairs, complete all as specified and directed by Engineer-in-Charge. Make: Prayag/Polytuf/Supreme

15mm bore, Pillar tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-110 gms), fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. MAKE: PARYAG/POLYTUF/SUPREME

15mm bore, Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms/20mm-125gms), fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. MAKE: PARYAG/POLYTUF/SUPREME

15mm bore, Stop valve standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms/20mm-92gms), fixed in repairs, complete all as specified and as directed by Engineer-in-Charge. MAKE: PARYAG/POLYTUF/SUPREME

PVC connections 15 mm size with PTMT nuts of length 450 mm, fixed in repairs, complete all as specified and diected by Engr-in-charge. Make: Prayag/Polytuf/Supreme

Viterous china wash basin, white flat back size 550 x 400mm including waste coupling CP 32mm dia and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP grating with holes fixed in repairs complete, all as specified and as directed by Engr-in-Charge. MAKE: CERA/HINDWARE/PARRYWARE

Vitreous china water closet, 'Orissa' pattern, including lime concrete bedding, size 580 x 440 mm white with integral foot rests excluding flushing cistern and flush pipe but including connection to trap, anti syphonage pipe etc. complete fixed in repairs, incl bedding with PCC 1:2:4 type B-1 using 20 mm grade stone aggregate complete all as specified and as directed by Engr-in-Charge. Make: Cera/Hindware/Parryware

Vitreous China wash down water closet pan and seat cover (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including P or S trap and including plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, including connection to drain pipe (or out going pipe) and to flushing pipe, antisyphonage pipe, etc. including cast iron 'P' or 'S' trap for 100mm bore of pipe, fixed in repairs complete all as specified and as directed by Engr-in-Charge. Make: Cera/Hindware/Parryware

10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, complete, fixed in repairs all as specified and as directed by Engr-in-Charge. MAKE: Cera Model Combiflush twin flush as per Cat Part No. B1020101 (Old Cat Part No 2603) or equivalent in HINDWARE/PARRYWARE

600 mm x 450 mm mirror of thickness 5/5.5mm of slected quality glass, mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete, fixed in repairs all as specified and as directed by Engr-in-Charge. MAKE: PARYAG/CERA/SAINT GOBAIN/MODI GUARD/TRIVENI FLOAT GLASS/HINDWARE

Supply and fixing in repairs health faucet manually operated (Hand held) complete set with CP Nipple-01 (100/50mm as required) and CP Tee-01 No connected to existing taps with 8mm dia 1.20 metre long flexible tube and wall hooks complete all as specified and as directed. Make: Cat part No ALD-CHR-573 of Jaquar or equal approved in Kohler

S & F in repair towel rail 600mm long of PTMT fixed with and including chrominium plated brass screws and wooden/plastic cleats (Min Wt 190 Gms). MAKE: PARYAG/POLYTUF/SUPREME

S & F in repair CP floor gratings 150mm dia all as directed by the Engr-in-Charge

S&F in repairs 15mm bore single leaver basin mixer with popup waste system with chrome finish complete all as specified nad as directed. Make: CAT PART No. OPP-CHR-15051BPM of Jaquar or in equivalent in Kohler/CERA

S&F in repair CP wall mixer 3-in-1 system with provision for bath Telephone shower and over head shower with bend pipe including hand shower and overhead shower complete all as specified and directed by the Engr-in-Charge. Make: CAT PART No. FLR-CHR-5281N (Florentine) of Jaquar or equivalent in Kohler/CERA

M&L for two coats cement base paint on newly plastered surfaces of wall including preparation of surfaces including curing before and after applying each coat complete all as specified and directed. MAKE : SNOWCEM/ASIAN/BERGER/DURACEM

M & L preparation of new plastered surfaces and applying three coats of white wash on walls complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of distempering with oil bound distemper white or any tinted on walls, filling gaps by putty after washing rubbing down and stopping of distermpered surfaces, over a coat of primer over and including 3 mm thick wall care putty complete all as specified and directed by Engr-in-charge. MAKE: NEROLAC PAINTS / JENSON & NICHOLSON / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS

Preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge. MAKE: NEROLAC PAINTS/ JENSON & NICHOLSON/BERGER PAINTS/ICI DULUXE/ASIAN PAINTS

Mehar Enterprises

R B TRADERS

M/S MA CONSTRUCTION Co

M/S Praveen Kumar and Sons

N K BUILDERS

SUMEET TRADING CORPORATION

M/S UNITED CONSTRUCTION CO.

VIJAY ENTERPRISES