138WE/L-48/2021-22

Amount

Dismantling wall and ceiling boards (fibre,pulp, insulation etc.) or insulation boards / slabs/ blankets, any thickness, including fillets, complete all as specified and as directed.

Dismantling timber scantling (framed work) under 40 sqcm in section, in fillets, rails, posts, rafters, purlins etc at any position, complete all as specified and as directed.

M&L for wooden floor tiles 7 mm thick with dove tailed joints laid over 150 micron polythene film and 3 mm thick foam as per manufacturer's instructions, including taking down of old wooden flooring and fixed with decorative wooden beadings as per site requirement complete all as spfd and directed.Make and shade of tiles be all as approved by GE.

S & F Gypsum ceiling board 10mm thick in 600 x 600 mm panel designer ceiling conforming to IS-14862 type B category three incl GI frame, grid work, Hold fast, suspended with GI wire complete as as specified and directed.

S&F of wooden panelling on vertical surface of wall using following specifications complete all as specified and directed:- (a) 2nd class hard wood wooden gutties of size 25mmx25mmx200mm depth fixed in wall by making holes in brick wall and making good in cement mortar 1:3. (b) Horizontal rummer 2nd class soft wood Kail( at 120 c/c of sextional area exc. 13 Sqm and n. exc 25 Sqm clean sawn treated with two coats of cerosite oil mixed with good quality pesticide for antitermite treatment. (c) 1st class soft wood (Deodar) boarding 12mm to 15mm thick as in wall panelling planed one side, wrought and other side clean sawn and applying two coats of good quality varnish on plain surfaces over a coat of primer mixed with good quality pesticide for antitermite treatment on the other side and fixed with screws/nails on wooden runners. (d) 1st class soft wood(Deodar) decorative breading 40mm wide on top surface of wall panelling including two coats of varnish.

S&F 6mm thick Veneered decorative plywood, grade 1(with BWR resin) with decorative face veneers on one face fixed with nails to timber frame work

M&L for 2nd class softwood clean sawn as in scantling fixed with nails exceeding 13 Sqcm and n.exc 25 Sqcm in section

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified

Demolition of cement concrete (unreinforced) of any descriptions, in ground floors not exc. 15 cm thick, above or below ground level, complete all as specified and directed.

M&L 25 mm thick, plain cement concrete, 1:2:4(Nominal Mix), type B-0 (using 12.5 mm graded crushed stone aggregates) as in floors finished rough surface to receive floor finishes, complete all as specified and directed by Engr-in-charge.

M&L screed bed or bedding laying of cement mortar (1:6) 15 mm thick as in floor finishes, complete all as specified and as directed.

M&L Rendering 10 mm thick cement mortar 1:4 as in vertical surfaces such as skirting , dados etc, complete all as specified and as directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exc. 0.18 Sqm but n. exc. 0.38 sqm , in floor etc, set and jointed in neat cement slury and pointed in white or coloured cement to match, complete all as specified and as directed.

M&L for Coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified

M&L Vitrified ceramic tiles light shade10 mm thick (square/rectangular) polished, area of each tile not exc. 0.36 Sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

Demolition stone slabs and tiles of any description or thicknes in floors, aprons and wall tiles etc

Material & Labour screed bed or bedding layer of cement mortar (1:6) ,20 mm thick for laying floor finishes, complete all as specified and directed.

M&L for machine cut Kota stone slab flooring, 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing (granite finish) and exposed edges of Kota stone shall be rounded complete all as specified and directed.

M&L for Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite black, complete all as specified

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, complete all as specified and directed.

M&L Sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

M&L for hard core of broken stone of boulders of guage n.exc 63mm deposited spread and levelled in layers n exc. 15cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2, using 40mm graded crushed stone aggregate as in sub base .

Taking down Chowkkats or frames exc. 1.5 Sqm but n. exc. 4.00 Sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down Chowkhats or frames n. exc. 1.5m each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Refixing and fixed in same opening of shutters of any description exc 1 Sqm but n exc 2 Sqm each complete all as specified and as directed.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified

S&F Powder coated (minimum thickness of power coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash,aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long(1 no.) hinges type B-21 100mm long (2 no.) suitable handle(1no) etc. complete all as specified

Supply and fixing Sheet glass 5.5 mm thick, exc 0.5 sqm in each pane complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples ,complete all as specified and directed.

S&F Floor door stopper 150mm long of alluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and as directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised, 150mm, complete all as specified and directed.

S&F Mild steel Mortice lock, 4 levers, vertical type, size 100mm, complete all as specified and directed.

Material & Labour 4mm thick figured glass,pin headed type and glazing with oil putty or aluminium beads fixed to steel etc complete all as specified and as directed

M&L for 9mm thick prelaminated particle board interior grade , prelaminated both side with decorated choice lamination fixed with screws to timber frame work and inserted in Aluminium frame as in shutters/wall panelling etc.

S&F Aluminium (Extruded section) door closer hydraulically regulated designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and as directed.

Demolition of brick or stone masonary including all necessary arches, pillars, quions etc built in cement mortar.

M/L Precast cement concrete solid blocks masonry exc 10 cm in width in PCC 1:3:6 type C1, using 20 mm graded stone aggregate & set in cement motar 1:6 complete all as specified and directed.

Taking down cement plaster on brick or stone walls, including racking out joints, hacking for key, scrubbing down with water etc.

M&L for 15mm thick rendering in CM (1:4) in two layers mixed with water proofing compound @ 3% by weight of cement in top 5mm thick finishing out the surfaces with fair and even without using extra cement complete all as specified and directed. (WPC shall be measured and paid separately)

Supply only integral water proofing compound

M/L Rendering 10mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:4) on concrete surface finished even and smooth without using extra cement

M/L Rendering 5mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:3) on concrete surface finished even and smooth without using extra cement, as in ceiling, complete all as specified and directed.

Material & Labour 75mm thick PCC 1:3:6 type C1 (using 40mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement complete all as specified and as directed.

Taking up or down steel tubing and conncection 20 mm, incl cleaning for re-fixing or removal to store

Taking up or down steel tubing and conncection 15mm, incl cleaning for re-fixing or removal to store complete all as specified and as directed.

S&F 25 mm bore 3 layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stabilty for hot & cold water supply including all PP-R plain and brass threaded polypropylene random fitting fixed complete to walls ,ceiling or floors

S&F 20 mm bore 3 layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stabilty for hot & cold water supply including all PP-R plain and brass threaded polypropylene random fitting fixed complete to walls ,ceiling or floors

S&F PPR gate valve conforming to ISO 2000 screw down end for PPR pipe or for union and fixed completey as specified for the size 25mm bore.

Providing 50mm thick insulation of water pipe line which includes of the following:- Export quality self regulating heat cable Aluminum tape K. Flex 19mm Rock wool Wire Mash Polythene Cello tape Aluminum sheet 28 gauge Screw

Taking down eaves gutters and rainwater pipes (any size or pattern ),including all fittings,heads,shoes,bends,swan necks etc.including cleaning or refixing or removal to store, complete all as specified and as directed

S&F 110mm PVC (SWR) pipes double socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S&F 110mm PVC (SWR) bends any radius, complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore single socketed ,in any length with rubber ring joints,laid in trenches or in floors cement complete all as specified

S&F PVC (SWR) pipe 110 mm bore single socketed ,in any length with rubber ring joints, fixed to walls, complete all as specified

S&F PVC (SWR) 110mm bore vent cowl complete all as specified

S&F PVC (SWR) 110mm bore junction single (single T), complete all as specified

S&F PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement, 75mm dia oulet complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed by Engr-in-charge.

M/L RCC using 1:2:4 type B1 using 20mm graded aggregate. Slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M/L form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) in flat rough finished surfaces of concrete.

M&L for mild steel TMT bars 10mm dia and over cut to length bent to shape as reqd , incl crancking bending ,spirally for hooping columns hooking ends and binding with and including mild steel wire not less than 0.9 mm dia.

M&L for mild steel TMT bars 6 mm to 8mm cut to length bent to shape as reqd ,as in stirrups and spacers.

Supply & Fixing in repairs Brass chromium plated bottle traps 32mm for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed, complete all as specified and as directed.

M&L for Complete removal of existing treatment in ceiling, and applying one coat of wall care putty (3mm thick) and preparation of surface with alkali resistant priming paint and applying two coats of distemper oil emulsion, complete all as specified and as directed.

M&L for Complete removal of existing treatment in wall, and applying one coat of wall care putty (3mm thick) and preparation of surface with alkali resistant priming paint and applying two coats of distemper oil emulsion, complete all as specified and as directed.

M&L for Roughning surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 Kg of cement per Sqm, complete all as specified and directed.

M&L, Rendering 20mm thick cement plaster in CM 1:4 on concrete surface finished even and smooth without using extra cement with water proofing compound as per menufactures instructions complete all as specified. Note : Water proofing compound shall be paid separately.

M&L for Bitumastic gola, with 80/25 bitumen and coarse sand mixture, 1:3 by weight, 8cm x 8cm at the junction of roofing, complete all as specified and directed.

M& L, Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces,complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified

S&F Bib taps, 15mm bore, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F in repairs 15mm bore stop cock fancy type chromium plated cast copper alloy screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule.

S&F PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F PVC towel rail 600mm long fixed with and including chromium plated brass screw and wooden/plastic cleats(minimum weight 190 grms), complete all as specified and directed.

S&F Grating square 150mm size of PTMT (Min weight 100 grms), complete all as specified and directed.

M&L PVC floor trap 75mm dia, plain with grating including jointing with solvent cement, complete all as specified and directed.

M&L for Preparing newly plastered surfaces of walls and applying two coats of distemper oil emulsion, complete all as specified and as directed.

M&L for Preparing newly plastered surfaces of ceilings and applying three coats of whitewash, complete all as specified and as directed.

M&L for Preparing old plastered surfaces of ceilings and applying one coat of whitewash, complete all as specified and as directed.

M&L for complete removal of existing old treatment of any description and preparation of old surfaces of walls, washing rubbing down and applying two coats of weather proof paints over a coat of exterior grade wall care putty and primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of weather proof paints over a coat of exterior grade wall care putty and primer complete all as specified and as directed.

S&F Harrison rails, anodised aluminium alloy, with fixing brackets, stops, rollers etc.

Surface dressing n,exc 15cm deep in soft/loose soil

Removal of excavated material n,exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point.

Aluminium, anodised, barrel tower bolts of extruded section, 150 mm long,complete all as specified and directed by Engr-in-charge.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

S&F table top basin (fixed in repair) size 600 x 385 x 195 mm code no VGS-WHT 81931N of make Jaquar, complete all as specified and as directed.

S&F wall hung basin (fixed in repair) with fixing accessories of size 610 x 480 x 195 mm Code no FNS-WHT-40801 of make Jaquar, complete all as specified and as directed.

S&F single piece WC with UF soft close seat cover (fixed in repair) hinges, fixing accessories set and cistern fiting of size 390 x 710 x 720 mm cat No VGS-WHT-81851SN of make Jaquar, complete all as specified and as directed.

S&F single lever basin mixer with popup waste system with 450 mm long braided hose (fixed in repair) with accessories set, cat No FUS-29023B of make Jaquar, complete all as specified and as directed.

S&F towel rack with hower hanger (stainless steel) with hock (fixed in repair) with accessories set, cat No ACN-1181FSH of make Jaquar, complete all as specified and as directed.

S&F towel ring square with round flange accessories set (fixed in repair) cat No ACN-1121N of make Jaquar, complete all as specified and as directed.

S&F toilet roll holder with flap, with accessories set (fixed in repair) cat No ACN-1153S of make Jaquar, complete all as specified and as directed.

S&F soap dispenser with glass bottle with accessories set (fixed in repair) cat No ACN-1135N of make Jaquar, complete all as specified and as directed.

S&F soap dish holder with accessories set (fixed in repair) cat No ACN-1131N of make Jaquar, complete all as specified and as directed.

S&F corner glass shelf (with bracket) with accessories set (fixed in repair) cat No ACN-1173 of make Jaquar, complete all as specified and as directed.

S&F tumber holder with accessories set (fixed in repair) cat No ACN-1141N of make Jaquar, complete all as specified and as directed.

S&F hand shower (health faucet) with 1m long easy flexible tube in chrome finish & wall hook, with accessories set (fixed in repair) cat No ALD-565 of make Jaquar, complete all as specified and as directed.

S&F wall mixer 3-in-1 system with provision of both hand shower and overhead shower complete with 115 mm long bend pipe connection legs and wall flange (without hand & over head showers) (fixed in repair) cat No FUS-29281 of make Jaquar, complete all as specified and as directed.

S&F two way bib cock with wall flange, with accessories set (fixed in repair) cat No FUS-29041 of make Jaquar, complete all as specified and as directed.

S&F angular stop cock with wall flange, with accessories set (fixed in repair) cat No FUS-29053 of make Jaquar, complete all as specified and as directed.

S&F waste couplng 32mm size half thread with 80 mm height with accessories (fixed in repair) cat No ALD-709 of make Jaquar, complete all as specified and as directed.

S&F over head shower 150 x 150mm square shape single flow (ABS body chrome plated with grey face plate) with Rubit cleaning system (fixed in repair) cat No OHS-35495 of make Jaquar, complete all as specified and as directed.

S&F shower arm 400 x 25 x 25mm square shape for wall mounted showers with flange (fixed in repair) cat No SHA-455L400 of make Jaquar, complete all as specified and as directed.

S&F easy flex tube in chrome finish 1.5m long with nuts (fixed in repair) cat No SHA-571 of make Jaquar, complete all as specified and as directed.

S&F hand shower 24mm dia round shape single flow (ABS body chrome plated with grey face plate) with Rubit cleaning system (fixed in repair) cat No HSH-5537N of make Jaquar, complete all as specified and as directed.

S&F aquafree waterless urinal (fixed in repair) of Make Hindware cat No 60017 of size 31.5 x 33 x 60 cm.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fitting such as switches ceiling roses, pendents, regulators, sockets, light fitting etc removing materials to store for keeping in safe custody or taking credit for above items should be made as per conditions separately) and making good disturbed surfaces, of walls, floors etc.

Taking down existing main switches and DBs including MCBs complete and removing material from site of work and making good disturbed surfaces of walls, floor etc.

M&L for point wiring for one light point or fan point controlled by one switch with PVC insulated copper conductor stranded cable of size 1.5 sqmm and including PVC casing/caping terminated in existing sunk Cl/ pressed steel terminal boxes for fixing and 1.5 sqmm PVC insulated copper wire as earth wire connected to earth folly and 3.00 mm thick plastic lamiated sheet cover all as spfd and directed by Engr-in-charge.

M&L for one bell/buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sqmm size.

All as per item No 114 here-in-before but 1.5 sqmm for one 3 pin 5 Amps socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on same board.

All as per item No 114 here-in-before but 1.5 sqmm for one 3 pin 5 Amps socket outlet independent including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on same board.

M&L for point wiring for 3 pin 15 Amps socket outlet independent with copper conductor cable PVC insulated multistrand 2.5 sqmm with 1.5 sqmm PVC copper conductor as earth wire connected to earth dolly and including PVC casing / caping with sunk cast iron.

M&L for Modular Switch 1 way 6A, 01 Module

M&L for Modular Switch 1 way 16A, 01 Module

M&L for Modular Socket 6A-2/3 Pin Combined 2 module

M&L for Modular Socket 6A/16A-2/3 Pin Combined 2 module

M&L for modular bell push 6A, 1 module

M&L for modular white cover plate with frame, 1 module

M&L for modular white cover plate with frame, 2 module

M&L for modular white cover plate with frame, 3 module

M&L for modular white cover plate with frame, 4 module

M&L for modular white cover plate with frame, 6 module

M&L for modular white cover plate with frame, 8 module

S&F ceiling rose surface bakelite two or three terminal all as specified and directed by Engr-in-charge

M&L for alamp holder PVC/Polycarbonate type with back plate suitable for batten fittings

S&F LED lamp 07 watt (warm white) 230V, complete all as specified and as directed.

Supply and fixing suface/wall mounted LED fittings with LED tube 18 watts (Warm white) capacity decorative ultra slim elegance LED lighting fixture with extruded AI. Heat sink, environmental friendly, energy efficient type 4 feet long channel type bracket including necessary connection prewired and making connection with 3 core copper flexible cable of appropriate size from ceiling rose/PVC connector to light fittings.

M&L for surface/ceiling mounting 2'x2' LED luminaire warm white fitting 36 watts.

M&L for surface/ceiling mounting 1'x1' LED luminaire warm white fitting.

M&L for Bed side lamp fitting cylindro track light fittings with complete accessories.

M&L for replacement of Endura Neo HE DL surface mounted LED downlighter with white power coated aluminium housing with integrated electronic driver 18 watts with complete accessories.

M&L for replacement of Building security light 25 watts LED fittings with 40mm dia GI bracket with clamps complete accessories.

S&F and replacement of submain wiring PVC conduit alongwith earth wire the following sizes of 2x16 sqmm +1x16sqmm of FRLSH PVC insulated copper conductor, single core cable in surface/recessed.

S&F and replacement of submain wiring PVC conduit alongwith earth wire the following sizes of 2x10 sqmm +1x10sqmm of FRLSH PVC insulated copper conductor, single core cable in surface/recessed.

S&F and replacement of submain wiring PVC conduit alongwith earth wire the following sizes of 2x6 sqmm +1x6sqmm of FRLSH PVC insulated copper conductor, single core cable in surface/recessed.

S&F and replacement of submain wiring PVC conduit alongwith earth wire the following sizes of 2x4 sqmm +1x4sqmm of FRLSH PVC insulated copper conductor, single core cable in surface/recessed.

S&F in replacement sheet metal enclosure TPN DBs with 200 Amps rated bus bar of 4 way 415 volts with blank plate complete with double door all as directed by Engr-in-charge.

S&F in replacement sheet metal enclosure SPN DBs with 200 Amps rated bus bar of 12 way 240 volts with blank plate complete with double door all as directed by Engr-in-charge.

S&F in replacement sheet metal enclosure SPN DBs with 200 Amps rated bus bar of 8 way 240 volts with blank plate complete with double door all as directed by Engr-in-charge.

S&F in replacement of MCB TPN 63 Amps 'C' series complete all specified and directed by Engr-in-charge.

S&F in replacement of MCB SPN 63 Amps 'C' series complete all specified and directed by Engr-in-charge.

S&F in replacement of MCB SP 6 to 32 Amps 'C' series complete all specified and directed by Engr-in-charge.

S&F in replacement of MCB SP 40 Amps 'C' series complete all specified and directed by Engr-in-charge.

M&L for earthing complete with galvanised steel earth plate 600x600x6mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI wire of size 4mm dia by means of nuts, bolts, washers etc made of and connected to test point and earth dolly as all shown in electrical plate No 3 of SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil, PCC (1:3:6) type C1 in chamber, pre cast RCC slab 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM jali (weight not less than 4.0 kg/Sqm) with cast iron frame, funnel, with wire mesh, 20mm bore light grade GI watering pipe, lugs, 15mm bore light grade GI protecton pipe, test point etc complete all as specified and as directed. Note : (i) item includes the cost of 7.5m GI pipe for protection of earth lead. (ii) Item includes the cost of 7.5m GI earth lead.

S&F for Ding dong bell AC 230 Volts, single pole

Taking down Old Exhaust fan servicing, Repairs and Refixing with complete all accessories

R B TRADERS

Mehar Enterprises

M/S SHAMSHER ALI SUFI

SHRI RAM CONSTRUCTION CO