CERTAIN REPAIR REPLACEMENT TO ROOF SHEETS FALSE CEILING WALL PLASTER AND MISC WORKS AT MES INSTLNS AT DALHOUSIE AND BAKLOH CANTT

Amount

Dismantling CGI or PGI sheet of any gauge and thickness or any pattern roof covering.

M & L for 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with L- type or J- type or cranked hook bolts and washers, in roofs, walls etc. with grade of zinc coating 275.

All as per item No 2 above but except sheeting

Galvanised plain mild steel sheeting of thickness 0.63mm grade O with 120 gm/sqm Zinc coating with L or J type or cranked hooks and washers bitumen washer as in ridge etc

All as per item No 4 above but except sheeting

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified,

Dismantling wall and ceiling boards any thickness including cover fillets.

4mm thick non asbestos fibre cement designer board ISI Marked fixed with screw to aluminium frame work in ceiling flat or sloppy as per manufacturer instructions

Ditto except non asbestos building boards

S&F Anodised aluminium snap grid frame work for false ceiling for size of grid 605 x 605 mm including hangers 6 mm dia GI (up to 1200 mm long) adjusting level fixed to roof complete all as specified

Dismantling framed timber scantling 40 Sq cm and over in section in any position

S&F structural steel work as in roof trusses (framed), trussed, purlins, rafter, crane gantries, rails & fastenings & heavy brackets framing including distance pieces, cleats etc. confirming to Fe 410-W (E-250 grade quality A).

S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates including bending and welding.

Dismantling wrought iron or mild steel work of any description not other wise provided.

S& F mild steel flat iron 40x5 mm for wind tie confirming to Fe 410-0 or Fe 310-o

Dismantling mild steel work of any description not otherwise provided for as in wind ties and fixing in same position

Demolition of cement concrete (unreinforcement) of any discription and in any position not otherwise specificcally provided for

PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in surface channel drains all as specified and directed.

M&L extra over forming fair finished drains or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stopped ends etc

Demolition of cement concrete in ground floor and paving n.exc 15 cm thick above or below ground level (unreinforced).

M&L for cement concrete 1:3:6 type C-2 (40mm graded aggregate)75 mm thick surface finished even and fair all specified to receive top layer.

M&L screed bed 15 mm thick in cm 1:6 for bedding layer to floor tiles

M & L coloured chequered cement concrete tile (Vibrator made ) 200mm x 200mm x25mm thick, set, jointed and pointed in neat cement slurry in floor with grey cement and pigment complete all as specified.

Demolition of stone/brick masonary built in cement/cement lime mortar.

M&L walling of random rubble stone masonery brought up to course, well bonded,bedded and solidly hearted, built in CM 1:6.

M&L walling of random rubble stone masonery brought up to course, well bonded,bedded and solidly hearted, built in CM 1:6. but Except stone.

M&L for rendering 15mm thick cement plaster on concrete surfaces or fair surface face of brick work in CM 1:4 surface finished even and smooth without using extra cement complete all as specified.

Preparation of new steel surfaces and applying two coat of synthetic enamel paint over a coat of red oxide all as specified

M & L for two coats white wash on walls on plastered surfaces as preparatory work on newly plastered surfaces.

Preparation of old painted steel surfaces (such as CGI sheet, GI water tube, fencing post etc.) and applying one coat of synthetic enamel paint over 10cm width or girth, complete all as specified

M/S RUDHRAKSH TRADING CO

m/S Varun Gupta

M/S Ajay Kumar Mahajan

M/s. Rishav Sood

M/s Shakti Electric Works

M/S KLM ENTERPRISES

Roshan Lal Thakur

Eshaan Construction Co.

malghotra construction co