CERTAIN REPAIRS AT OTM ACCN COD AND MDC MALAD COMPLEX UNDER GE (NORTH) SANTACRUZ MUMBAI

Amount

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Demolition of cement concrete(unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and removal of rubbish to outside MD land etc complete all as specified and as per directed all as specified and as per directed

Demolition of cement concrete( reinforced) in landing slab, Chullah hoods, manhole covers, roofs, floors, beams, stair case, landing, chajja and similar suspendd work complete all as specified and as per directed all as specified and as per directed

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work/stone masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, PCC coping etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

Taking down of chowkats or frames not exceeding 1.5sqm each with shutters (without taking off shutters from the frames) & removing clear off site after credit is recovered by Dept complete all as specified and as directed by Engineer-in-Charge

Taking down chowkats or frames with shutter (without taking off shutter from frame) exceeding 1.5 sqm but not exceeding 4 sqm each including fittings & removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed by Engineer-in-Charge

Material and labour for Building up the profile of structural members by using polymer modified mortar upto 20mm average thickness including levelling profiling work rate including following all process with material :- (a) Surface preparation of existing concrete components including grinding/rubbing carefully by grinder without damaging the existing concrete and debris removed outside MD area. (b) Providing & applying rust cleaner to existing corroded reinforcement of approved make (c) Providing and applying two coat of anticorrosive epoxy phenolic rebar protective system to existing as well as new reinforcement (d) Priming cum bonding coat of two component peroxide resin confirms to ASTM-C-882-91 including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), shear key fixing with drilling and epoxy grout wherever required, Scaffolding at any height & mixing, laying, levelling and finishing including curing and work shall be execute as per manufacturer instruction and from authorised applicator complete all as specified and as directed by Engineer-in-Charge. Note : All materials should be approved make such as Dr Fixit, Fosroc, Sika, Krishna conchem or equivalent.

Supply and fix mild steel TMT bars, 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

ditto as per item no.9 above but 5mm dia and over up to incl. 10mm dia in stirrups, spaces and binders complete all as specified as directed by Eng-in-charge.

Demolition of reinforced cement concrete of any description in any position (reinforcement cut as required to facilitate demolition) as in manhole cover and simillar and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge. Note : Reinforcement obtained from this item shall be handed over to contractor after credit is recovered by the Dept.

Supply & fix MS/TS dowel pins/staple/shear pins including drilling holes in concrete and providing labour but excludeing the materials for grouting the pins etc complete all as specified and as directed by Engineer-in-Charge.

Material & labour for repairing of damaged concrete portion by using superfluid dual shrinkage compensated structural grade M-40 micro concrete of at all levels with all leads and lift as directed including mixing, laying, levelling, finishing and curing complete all as specified and directed by Engineer-in-Charge. Make: Fosroc / SIKA / BASF / Krishna Conchem or equivalent approved .

Material and labour for formwork using steel shutters or 12mm marine ply to have the smooth finish to pour the micro concrete/ concrete including de-shuttering etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan, exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius, in half brick thick walls with old size bricks, built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge

Material and labour for 10 mm thick rendering in Cement Mortar (1:4) on internal wall surface including dubbing out plaster in Cement Mortar (1:6) of any thickness & finishing the surface even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 5mm thick plaster in cement mortar (1:3) on concrete surfaces of ceiling and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 15 mm thick rendering in Cement Mortar (1:4) on brick or concree surfaces including dubbing out plaster in Cement Mortar (1:6) of any thickness & finishing the surface even & smooth without using extra cement but using water proofing compound complete all as specified and as directed by Engineer-in-Charge. Note: waterproofing compound shall be measured and paid separately

Supply only integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit

Material and labour for Plain Cement Concrete 25mm thick 1:2:4 type B0, using 12.5mm graded stone aggregate as in flooring,finished fair and even etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for light shade, vitrified ceramic tiles, 8-10mm thick (minimum), (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in cement mortar 1:6 including scarifying the floor complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for light shade, vitrified ceramic tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, on vertical surfaces etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 10mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles/ Orient bell

Material and labour for marble work 20 mm thick machine cut, makrana colour/white, table rubbed and polished, bedded and jointed as in steps, jambs, pillar, window cills, cooking platform and like bedded and jointed with grey cement slurry and pointing in white cement 1:2 using marble dust with admixture of pigment to match including 20mm thick screed bed/rendering coat in cement mortar 1:4 etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for machine cut Kota stone slab flooring 20-25 mm thick over and including cement screed bed 20 mm in Cement Mortar (1:4) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

All as per item No.25 described here-in-before but 20-25mm kota stone as in riser of steps, skirting, dados etc laid over cement mortar 1:4 and jointed complete all as specified and as directed by Engineer-in-Charge.

Material and labour for grinding and polishing,the existing Kota/ Marble stone complete all as specified and as directed.

Material and labour for non skid ceramic "Joint Free and coloured" square tiles (300x300mm) x 7mm to 8mm thick thick, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed of cement mortar 1:4 complete all as specified and directed by Engineer -in-charge Make: H R Johnson / Orient Bell Tiles / Kajaria / Somany Tiles Ltd / Nitco tiles / Swastik Tiles / RAK tiles/ Orient bell

Material and labour for coloured glazed ceramic tiles of size 600mm x 300mm x 7 mm thick/ 450mm x 300mm x 7mm (or nearest size) ,on vertical surface such as skirting, dado, riser/steps etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over & including cement plaster 10mm thick in Cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles / RAK tiles/ Orient bell

Material and labour for 50mm thick cement concrete (1:3:6) type C2, using 40mm graded stone aggregate as in plinth protection and finishing the surfaces even and smooth without using extra cement, including joints of plinth protection filled with bitumen mastic (1:3) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 100mm thick Plain Cement Concrete 1:4:8 type D2 using 40mm graded stone aggregate as in foundation / mass concrete/filling complete all as specified and as directed by the Engineer-in-charge

Material and labour for vibrator moulded(coloured) machine pressed precast concrete interlocking paver block, of any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment including 25mm thick crushed stone sand cushioning including watering and consolidation below paver block complete all as specified and as directed by Engineer-in-Charge. Make: Mehtab Tiles/Indore/M/S Ultra Tiles/NITCO/Topaz Tiles/Navya Tiles Jodhpur

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to therequired line, level and curvature, jointed with CM 1:3 including making joints except at sharp curve shall not to ore than 5mm, including making drainage opening whever required complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 30 mm thick factory made moulded PVC door (Wood free) consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 20mm x 40mm for stiles as well as top, bottoMaterial and labourock rail. M.S. frame shall have a coat of metal primer of approved make & manufacturer. The inside panel shall consist of 20mm thick multi-chamber hollow PVC section of 1mm wall thickness, bonded using solvent cement / cynoacrylate adhesive with 5 mm (+0.25) thick moulded PVC sheet of density 600 kg/cbm with 2, 4, 6 raised panel design in plain / prelam colours after routing the moulded design on one side of the inside panel. 5 mm (+0.25) plain / prelam PVC sheet to be pasted using solvent cement / cynoacrylate adhesive on other side of the hollow PVC section. All the four edge of the panel to be sealed with lipping of 10 mm thick & 20 mm wide PVC sheet baton made by sticking 2 nos. foam PVC sheets of 5 mm (+0.25) thickness using PVC solvent cement adhesive. Door edge lipping to be painted with PVC ink of matching colour of Plain/Prelam moulded PVC sheet of door 20 mm thick (5 mm x 4 nos.) thick PVC sheet to be given for lock provision at lock height. Door to be fixed with frame with 3 nos. stainless steel butt hinges of size 100mm x 25mm x 20mm and 50 mm long steel screws drilled suitable to pass through both the walls of the M.S. tube other hardware should be fixed with 25mm x 8mm size steel screws etc. complete as per manufacturer's specification and drawing complete all as specified and as directed by Engineer-in-Charge. Make : M/S RajshriPlastiwood, Indore (Rajshri)/ M/S Sintex Industries Ltd (Sintex)/ M/S AccuraPolytech (Accucel)/ M/S Dura Plast Extrusion (Duraplast)/ M/S Madhu Industries (Madhu Industries)/ M/S Navratna Co Speciality Chemicals(GIZA)

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing on Serial Page No 151 & 180 of SSR Part II (pertaining to item No 08095) and edges to be painted to match with prelam sheet complete all as specified and as directed by Engr-in-Charge. Make : RAJSHRI / SINTEX / TUFFFLON / M/s Navratan Specialty Chemical LLP – ‘Brand : GIZA’

Supply & Fiix Factory made single extruded WPC (wood polymer composite) soild decorative type flush door shutter of size 30mm thick comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) and having minimum density of 650 kg/cum, screw withdrawal strength of 1800 N(face) and 900 N(edge), minimum compressive strength of 50 N/mm2, modules of elasticity 900 n/mm2 and resisitance to spread of flame of class A catgory with property of being termite/borer proof water/moisture proof and fire resistant WPC to be laminated with pvc foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with SS butt hinges of required size with necessary full body threaded star headed counter sunk ss screws complete all as specified as directed by Engineer-in-charge. Note: SS butt hinges and SS screws shall be paid seprately. Make: Rajashri/Giza/Echon/Floresta

Supply & Fix 30mm thick "FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER" decorative type consisting of density 600 kg/cum manufactured by an ISO 9001-2015 certified company, door to be panelled with SS mosquito mesh and XTN aluminium mesh for additional strength and saftey purpose (confirming as per IS 4020) the door should be water proof, termite proof, fire resistant and having screw holding capacity door to be fixed with 3 nos. MS powder coated butt hinges size 100x2x32mm long steel screws drilled suitable to pass through both the walls of the MS tube other hardwares should be fixed with 19x6mm size steel screws etc. complete as per direction of Engineer-in-charge, manufactures specification and drawing. Make: Rajashri/Giza/Echon/Floresta

Supply and fix stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-charge.

Supply and fix extruded aluminium alloy with galvanised mild steel butt hinges, medium weight, 100mm size all as specified and directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 150mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 150 mm long complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix 15 micron coloured powder coated aluminium sections for sliding (3 Track) or openable windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified and as directed by Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix 4.0mm thick figured glass, pin headed type, ordinary quality, fixing with oil putty and glazing clip, in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge

Supply and fix 15 micron coloured aluminium anodised grill of design No DG-101 of Decogrille or equivalent , cut to required size/shape, and fixed in position with and including aluminium beading and frame complete all as specified and as directed by Engineer-in-Charge. Make: DECOGRILLE of Associated group / Royal Alum grill Pvt Ltd or equivalent make as approved by GE

Supply and fix in repair vitreous china squatting pan Orissa pattern of size 580 x 440mm white with integral foot rest, 'P' or 'S' trap front and back inlet and including connection to trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern & flush pipe) all as specified and as directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' of 'S' trap (of size 465mm x 355mm x 265mm),including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc including health faucet (body cleaner) with 1.0m tube and hook (PVC tube) and toilet paper holder with flap guard complete all as specified and directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets, including flush pipe of polyethylene of low or high density or PVC 32mm dia including connection to pipe and fixing of chains and pull or lever complete all as specified and as directed. Make : M/S Johnson Peddar/ Parryware/ RAK Ceramics/ CERA

Supply and fix in repairs vitreous china wash hand basin white flat back or angle back of size 580 x 450 mm excluding taps, waste chain and plug and porcelain stopper but including CI brackets, cutting for and pinning in ends of brackets or erecting stand including 32mm bore discharge pipe with waste coupling of PTMT etc complete all as specified and as directed. Make : CERA/ RAK Ceramics/ Parryware/ Hindware/ Neyveli Ceramics (Neycer)/ Jaquar/ Kajaria (KEROVIT)

Supply and fix in repairs vitreous china urinal half stall including connections to flushing pipe and outgoing pipe as specified as directed by eng-in-charge.

Supply and fix in repairs pillar taps, fancy typ, cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes, 15mm bore complete all as specified and directed by Engineer-in-Charge. Make : Jaquar/ Marc/ CERA/ Kohler/ Player

Supply and fix in repairs 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed by Engineer-in-Charge. Make : Jaquar/ Marc/ CERA/ Kohler/ Player

Supply and fix in repairs stop valve /angle valve, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar/ Marc/ CERA/ Kohler/ Player

Supply and fix in repairs swivel shower rose(fancy type) chromium plated 125 mm dia, heavy duty pattern with or without swivel joints, suitable for jointing to 15 mm bore steel water tubing or union complete all as specified and as directed by Engineer-in-Charge. Make :Soma / Leader / Zoloto / Jaquar

Supply and fix in repairs concealed stop valve/angle valve, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar/ Marc/ CERA/ Kohler/ Player

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

Refixing old steel tubing and connections for 20mm bore of pipe in new or old position (walls, ceilings floor etc) complete all as specified and directed.

Supply and fix mild steel tubing medium grade 20mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clampss complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Refixing old steel tubing and connections for 15mm bore of pipe in new or old position (walls, ceilings floor etc) complete all as specified and directed.

Supply and fix mild steel tubing medium grade 15mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clampss complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix , stop valve/push cocks , cast copper alloy, chromium plated fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 20mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repairs, sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever CI brackets and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm including necessary fittings such 40mm coupling waste pipe etc complete all as specified and as directed by Engineer-in-Charge. Make : Diamond / Nirali / Neelkant/Parryware/Prayag

Supply and fix in repairs rotational molded polyethylene water storage tanks 1000 litres capacity with inlet connections, three layer (cylindrical or vertical with closed top) HDPE with ISI marked, hoisted and fixed in position either inside or out side of the building, including fixing accessories and connecting up pipes securing access covers etc complete all as specified and directed by Engineer-in-Charge Make : Sintex / Polycon, Jaipur / Rotex / Infra

Supply and fix in repairs Ball Valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed of 20mm bore (Minimum weight - 210 gms) complete all as specified and as directed by Engineer-in-Charge Make- Jaypee /GMP / Neta/ Zolota/Prayag Polymer/ Symet

Supply and fix in repair PVC connection, 15 mm size 450 mm long both end socket fix complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply and fix in repairs tubular towel rail aluminium anodised 20mm dia, 'D' type, 60cm long between flanges fixed to walls with screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs Soap dish, vitreous China, white, approximate size 160 x 160 x 90mm fixed to plugs with chromium plated brass screws complete all as specified and as directed by Engineer-in-Charge. Make : CERA/ RAK Ceramics/ Parryware/ Jaquar/ Hindware/ Johnson/ Kajaria (KEROVIT)

Cutting chases exce 10cm but not exce 20cm in girth,in brick / stone wall pinning in. making good to facings where required and pointing in cement mortar 1:3 and cutting chases for fixing of PVC pipe / GI pipe of 15 &20mm bore and making good in CM 1:6 complete all as specified and as directed by Eng-in-charge

Supply and fix in repairs PVC (SWR), type B, single socketed rain water/soil waste/vent pipes with rubber ring joints, 110mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge.. Make: Prince / Supreme / Finolex

Supply and fix in repairs PVC (SWR), type B, single socketed rain water/soil waste/vent pipes with rubber ring joints, 150mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge.. Make: Prince / Supreme / Finolex

Supply and fix in repairs PVC (SWR) bends any radius, 110mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix in repairs PVC (SWR) bends any radius, 150mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Material and labour in repair for Prelaminated particle board 12mm thick , exterior grade, prelaminated one side with decorative choice lamination & other side plain, fixed with screws to timber frame etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Stainless steel butt hinges medium weight of size 100mm all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 150 mm long complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy of size 150mm, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge.

Dismantling posts or struts (wood, steel or R.C.C.) any section, embedded in concrete, including taking out embedded portion and making good disturbed ground complete all as specified and as directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for & removing clear off site after credit is recovered by the dept complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails, and fastenings and heavy bracket framing, (beam, tee, angle, channels or flat sections) including notching, drilling, fitting, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts) conforming to Fe 410 W Gde E- 250, Quality B complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge Note- Work to be carried out for height upto 15 mt and above/ factory type bldg/Hanger) Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Supply and fix Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge Note- Work to be carried out for height upto 15 mt and above/ factory type bldg/Hanger) Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Material & labour for Rolled mild steel as in MS base plates (plain or chequered), channels , square cut or notched ( ordinary and counter sunk) forming holes including cutting ,welding or connecting conforming to Fe-410-W (Gde-E-250) quality-A complete all as specified and directed by Engineer in charge.

Supply & Fix anchor fastner, 12mm dia 100mm long or similar approved make fixed with anchor grout lokfix E77 or approved make of similar characteristics, the thixotropic nature of lokfix polyester resin grout P reduces flow of grout out of the hole, in overhead or horizontal holes incl. drilling holes of required sizes cleaning with the same with air pressure and filling with chemical as secified above placing of MS plate of required size and shape and drilling/ fixing the anchor bolt fastner complete all as specified and directed by Eng-in-charge. Note:- All MS items weight will be measured seperatly.

Material and labour for PCC 1:2:4 type B1 (using 20 mm graded aggregate), cills, steps; seismic and other similar bands, plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones,bed plate complete all as specified and as directed by Engineer-in-Charge

Dismantling of wall and ceiling board (fibre, pulp, insulation etc) or insulation boards/slabs/blankets of any type & any thickness including cover fillets & removing clear off site complete all as specified and as directed by Engineer-in-Charge.

Supply and fix anodised aluminium snap grid frame work for false ceiling conforming to IS 733, IS 737 and IS 1285 including all ceiling cleats, 4 mm dia GI wire suspender with necessary main tee 35.00 x 23.50 x 1.50mm, cross tee and wall angle of size 23.50 x 23.50 x 1.5 mm with 605 x 605 mm grid system including exposed metal frame ceiling with 8mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fiber for fixing in 600 x 600 mm grid system with all connected accessories suitably placed in false ceiling grid as per manufacture instruction complete with necessary design in single/double complete all as specified and as directed by Engineer-in-Charge. Make: Gypsum board /Arm Strong/Ramco/Bisan

Matewrial & Labour for tightening, adjusting and resecuring the existing loose snap grid and fixing the existing false ceiling board in same position including taking down complete all as specified and as directed by Engineer-in-Charge.

Material and labour wall paneling made of 5 mm thick prelaminated PVC hollow section with tonge and groove joints fixed on wall with necessary screw and adhesive etc complete all as specified and directed by engr in charge. PVC U channel will be provided on top and bottom and PVC angle will be provided in all corners consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing

Material and labour for preparing new steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge. Make: Make : Asian Paints/ Nerolac Paints/ Dulux ( Akzonobel)/ Nippon Paint India Pvt Ltd

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper with roller over a coat of alkali resistant wall primer over 2mm thick layer of wall care putty complete all as specified and as directed Make of Distemper: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints Make of Putty: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty

Material and labour for preparation of new plastered surfaces of wall & applying two coats of cement based paint over a coat of primer complete all as specified and as directed by Engineer-in-Charge. Make : Snowcem/Duracem/Aquacem/Berger/Shalimar

Material and labour for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment on wall surfaces by washing rubbing down and scrapping with wire brush and applying two coats of oil bound distemper with roller over a coat of alkali resistant wall primer over 2mm thick layer of wall care putty complete all as specified and as directed Make of Distemper: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints Make of Putty: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty

Material and labour for dismantling of rolling shutter of any size and any description including all connected fittings etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 1.25mm thick steel rolling shutters, with ball bearing, gear operated type with bevel gear box and crank handle, safety lever locks mild steel with 4 levers as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position etc complete all as specified and as directed by Engineer-in-Charge. Make : M/s Swastik Rolling Shutters, Mumbai / M/s Shree Lakshmi Engg Wks, Bangalore / M/s Senthil Rolling Shutters & Engg Co, Chennai / M/s Jayaraj Industries, Chennai

Material and labour for re-fixing rolling shutter of any size and any description, dismantled vide Item no. 98 above carefully, without disturbing or deforming including all connected fittings/fixtures, oiling, greasing to shutter etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 3.0mm thick sheet glass, ordinary quality, in square exceeding 0.5 Sqm in each pane including hacking out from wood/metal frame complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix 4.8mm thick sheet glass, ordinary quality, in square exceeding 0.5 Sqm in each pane including hacking out from wood/metal frame complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repair mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.0mm and fixed with tinned tacks , or galvanised wire staples to wooden/steel frames with beading complete all as specified and as directed by Engineer-in-Charge

Note: Deduct Credit for demolished / dismantled material of Rs. (-)1,30,715.00 (Minus) as listed in Schedule of Credit. Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum'

M/s. Deepak Traders (BID ID -3460954)

Vishal Builders (BID ID -3454978)

KAJAL CONSTRUCTION (BID ID -3456568)

CROSSLINE ENGINEERS AND CONTRACTORS (BID ID -3456346)