Supply Installation Testing and Commissioning of 13 No. G Plus 5 05 passengers Customized MRL lifts at Transit Accommodation at Zewan Pampore.

Supply, Installation Testing & Commissioning of Customized 05 Passenger (G+5) MRL lift at Transit Accommodation Zewan (including minor civil and electrical works such as whitewashing, lighting of shaft, brick work and marbling of doors at all floors ,covering of lift shaft at top etc). The lift shall be suitable for 05 passengers, of standard design having speed of 1.0m/s serving from ground to 5th floor i.e. 06 stops and 06 landings. The elevator shall be of state of art technology, energy efficient drive and all its components/ accessories shall conform to relevant IS standards. (The Defect Liability Period (DLP) of the equipment shall be 01 year) . • Machine – Gearless machine located in the shaft on the top of guide rails. • Power Supply – 400/415 V (3 Phase AC) • Car Group – Simplex Full Collective Control • Traction Media --- To be provided by firm. • Available Shaft dimensions -1295 mm (W) x1524mm (D) • Required Overhead - 4000mm • Available Pit depth - 1650mm. • Landing door – Telescopic/centre opening . • Car Finish - stainless steel in hairline finish. • Car door and landing door finish - stainless steel in hairline. • Handrail - round handrail in stainless steel finish provided on rear wall of car. • Alarm button in car operating panel. • Automatic operation for car fan. • Anti-nuisance (car call Protection) • Cross Flow fan in car for ventilation • Door open and door close buttons in car operating panel. • Emergency light • Full load by-pass • Infra–red screen for car door • Fire Rated Doors ---- 2 Hours • Overload function • Phase failure and phase reversal protection. • Automatic rescue device in case of power failure. • Attendant control. • Car Position Indicator – To be provided by firm. • Fireman control • Nudging Service • Voice Synthesizer.

SITC of 10 KVA servo- Stabilizers Including all allied electrical accessories. The stabilizer should have following specifications main supply a) Capacity:10 KVA, 3-phase unbalanced type b) Input: (100-265) V AC P-N; (150-460) V AC P-P c) Output: 415 V ±1%-phase to phase d) Supply: 3 phase, 4 wires, 50Hz e) Operation: Automatic f) Duty cycle: Continuous g) Transformer windings: Copper wound on CRGO laminations as per IS specifications h) Cooling: Oil cooled i) Efficiency: Better than 98% at full load j) Overload capacity: 15% for continuous 4 hours k) Waveform distortions: Nil 1) High speed voltage correction: up to 8V to 20V per second m) Protections: Under voltage, Over voltage and Overload with time delay. Other features: LED indicators, Digital AC ammeter, AC voltmeter, Frequency meters, Phase Sequence meters, Single phase preventer, and Stabilizer by-pass arrangement. The Job further includes P/F of 63 Amp 4 Pole MCCB with 25kA breaking capacity as incomer to the Servo Stabilizer to be provided in CRC Enclosure as per IS/IEC: 60947 with all other incidental works thereof included

Earthing: Providing and Laying of Copper (cu) strips and cu plate for proper earthing of all Electro-mechanical components carrying main current, including but not limited to the motor and electric panel. Use of bolts or screws and cu strips to establish grounding connections on each component. The job includes earth work by using labor for making a pit of suitable size for proper earthing and after that laying copper plate of minimum size 60cm width, 60 cm height and 3.15mm thickness and filling the pit with chemicals (chemical earthing). The earthing cu strip must have cross section not less than 24 mm^2. The job further includes laying of perforated conduit pipe from ground up to cu plate having funnel at top as per actual requirement at site & as per IS 3043 (1987)

Providing/Fitting of 3.5 core, 35 sq.mm armored Al, XLPE insulated cable for connecting power source to Servo stabilizer to 3-phase 4 pole 63 Amp Change Over panel duly thimbled and PVC tapped ends in different shades using Crimping tool along with conduits / cable trays & clamps wherever required conforming to IS: 7098.(for all lifts)

Providing/Fitting of 4 core, 10 sq.mm XLPE insulated armored Cooper cable for connecting Lift panel to the changeover panel duty thimbled and PVC tapped ends in different shades using Crimping tool along with conduits cable trays & clamps wherever required conforming to IS:7098 (for all lifts)

Providing/fitting of 100 amp Change Over Panel comprising copper Bus bar, incoming MCCB (63 Amp) outgoing MCCB (63 amp) and on load changeover switches for DG and main Supply In a CRC Panel duly powder coated.

Comprehensive Maintenance Contract (CMC) for 2nd & 3rd year post 1st year DLP (for all lifts)