PROVISION OF PUMP ROOM WITH UG SUMP FOR WATER STORAGE NEAR SINGLE LIVING SAILOR BLOCK (P-106) AND SECURITY GRILLS AT CERTAIN MD ACCN, CLOTH HANGING, DRYING ARRANGEMENT AND PROVN OF WATER SUPPLY CONNECTION FOR ARBORICULTURE AND DEFICIENT WATER TANKS

Amount

Dismantling carefully RCC work as in, Roofs, floors (other than ground floors), beams, staircases, landing,chajjas RCC water tank and similar suspended worketc by low impact Hammer/Breakar without damaging the structure & cleaning and disposal of debris out side the MOD land. complete all as specified and directed.

M &L for precast cement concrete block masonary with solid blocks with Type C1 ( 1:3:6 ) exc 10cm in width and setting in mortar 1:6 complete all as specified and directed.

M & L for RCC M 30 Design mix as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like complete all as specified and directed.

M & L for Use Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in soft / disintegrated rock and getting out all as specified and directed.

Excavating over areas, exc 1.5 m deep but not exceeding 3.00m and getting out in soft / disintegrated rock and getting out all as specified and directed.

Excavating over areas, exc 3.00 m deep but not exceeding 4.5m and getting out in soft / disintegrated rock and getting out all as specified and directed.

M&L for hardcore of gauge n.exc 0.63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface of a broken stone or boulders complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (40 mm graded aggregate ) in foundations, filling and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete with Design Mix M-30 using 20mm graded stone aggregate in foundations complete all as specified and directed.

M&L for reinforced cement concrete with Design Mix M-30 using 20mm graded stone aggregateWalls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses® complete all as specified

M&L for reinforced cement concrete with design Mix M-30 using 20mm graded stone aggregate in pillars, piers, posts and struts complete all as specified

M&L for reinforced cement concrete with design Mix M-30 using 20mm graded stone aggregate in Beams, cantilevers, bressummers,lintels complete all as specified

M& L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter ® of flat complete all as specified and directed.

M& L for Formwork to faces of walls, retaining walls, abutments,parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter curved surface complete all as specified and directed.

M& L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M& L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat complete all as specified and directed.

M&Lfor form work to edge of concrete RCC slab or RCC band exc 10cm wide but n exc 20 cm wide and rough finished surface complete all as specified and directed.

M&Lfor form work to edge of concrete RCC slab or RCC band exc 5cm wide but n exc 10 cm wide and rough finished surface complete all as specified and directed.

M & L for TMT bars 10mm dia and over cut to length, bent to shape reqd, inculding cranking,bending spirally for hooping for Columns, hooking ends and binding with and incl MS wire(annealed) not less than .90mm dia complete all as specified and directed.

M& L for TMT bars 6 to 10mm dia as in reinforcement cut to length bent to shape required including cranking, bending and spirally binding, with mild steel wire not less than 0.09mm dia or securing with clips as in Stirrups, binders, rings etc.

S&F 100 mm steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed

M&L for 15mm thick cement plaster in cement mortar (1:6) on fair faces of brickwork or concrete surfaces and finished even and smooth without using extra cement .

M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of primer .

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out soft in complete all as specified and directed.

Removal excavated material n.exc 50m and deposing where directed a a level n.exc 1.5 m above the starting point soft/loose soil complete all as specified and as directed.

M & L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 100 mm thickness M-50 Grade with grey cement and pigments complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1, using 20mm graded stone aggregate for edgi to interlocking tiles etc.complete all as specified and directed.

M & L for Rendering 15 mm thick in (1:4) cm (in two coats (15mm) with both coats mixed with liquid water proofing compound, surface finished even and fair without using extra cement complete all as specified and directed. ( Note : WPC will be measured separately).

Supply only polymer based liquid water proofing compound complete all as specified and directed.

M&L preparation and cleaning new rcc of inside surfaces of wall, bottom of Dome of Over Head or UG Sump Reservoir Tank by brush and treating surfaces with the methodology as under :-(a) Seal sanitary pipes entering through the walls and floor with Dr. Fixit Bathseal Tape (or equivalent as approved by GE) and grout the gaps with Dr.Fixit Bathseal grout - a non shrink cementitious grout (or equivalent as approved by the GE).(b) Apply the first coat of Dr. Fixit Fastflex (or equivalent as approved by GE) maintaining the saturated surfaces in dry condition.(c) Embed a glass fibre mesh measuring 50 gsm over and including the angle fillets as a reinforcing strip and allow it to soak completely.(d) Immediately apply the second coat of Dr. Fixit Fastflex (or equivalent as approved by GE) to sandwich this glass fibre mesh between these two coatings.(e) Apply the third coat of Dr. Fixit Fastflex (or equivalent as approved by GE) and sprinkle coarse sand while it is still wet.(f) Subsequent to above, apply first brush coat of Dr. Fixit Dampguard (or equivalent as approved by GE). Allow drying for 6 to 7 hours then apply second brush coat of Dr. Fixit Dampguard (or equivalent as approved by GE). Allow it to sure completely set in position for 24 hours before using.

M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, benching, haunching , water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M & L for providing pre-cast cement concrete landing, cover slabs, chullah hoods, chajjas, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate and setting in cement mortar 1:6 complete all as specified and directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in Hard/ Dense soil, and removing surplus soil to a distance n.exc 50 mtr. complete all as specified and directed.

M & L for Plain Cement Concrete Type C2 1:3:6 (using 40 mm graded granite stone aggregate) in foundations, fillin complete all as specified and directed. g and mass concrete

M & L for MS round bars 10mm dia and over as in RCC posts & securing chainlink fencing fixed to RCC fencing post as directed.

S&F angle iron in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) in-cluding all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0

S & F of mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other or screwed both ends, each screwed ends to be fitted with washer and one hexagonal or square nut, exc. 5 cm and not exc. 10 cm long and 11 to 15 mm dia of shank complete all as specified and directed.

M&L for preparing the new steel surfaces of Eaves gutter and pipes any descrip?tion, n. exc 60 cm girth including holderbats, distance pieces, etc.(length measured over bends, branches etc. and applying two coats of synthetic enamel paint over a coat of red oxide primer

M&L for Preparation of new steel surfaes of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer

M&L PVC coated chain link fencing, size n exc 40mm x 40mm The dia of GI wire shall be 2.5mm to 3mm and thickness of PVC shall be 1mm to 1.5mm fixed to the posts complete all as specified and directed.

M&L Formwork to rough finished surfaces of sides pillars, posts, struts, piers, columns, and stanchions etc. complete all as specified .

M & L for Rendering 20mm thick in (1:4) cm (in two coats (15+5mm) with both coats mixed with liquid water proofing compound, surface finished even and fair without using extra cement complete all as specified and directed. ( Note : WPC will be measured separately).

M&L for rendering cement plaster 5 mm thick in cement mortar 1:3 on fair faces of concrete in ceiling, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new painted surface of ceiling and applying three coats of white wash all as specified.

M & L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer using roller etc complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV esistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

S&F extruded Powder coated aluminium section as in Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and all directed

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

M&L 75 mm thick plain cement concrete 1:4:8 type D-2 ( using 20 mm graded stone aggregate) as in sub base, floors etc complete all as specified.

M&L 25 mm thick plain cement concrete 1:2:4 type B-1 ( using 20 mm graded stone aggregate) as in floors finished even and fair,all as specified.

M&L 75mm thick cement concrete 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection & paving, finished even & smooth without using extra cement. complete all as specified .

S&F IInd class hard wood plain solid straight chowkats and framed rebated on the solid rounded put togeather with glue pinned at joints all as specified.

S&F 35 mm thick, 2nd class hard wood factory made, plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F Extruded Aluminium anodised, barrel tower bolts of extruded section 100mm long complete all as specified .

S&F Aluminium alloy handles, fabricated type, anodised 75mm size all as specified.

S&F butt hinges medium weight 100 mm size all as specified.

M &L Aluminium alloy, anodised sliding door bolt,300mm long with hasp & staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast alluminium alloy all as specified

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for manholes, cesspits, shafts etc. not exc. 10 Sqm on plan and getting ou t soft / disintegrated rock complete all as specified and directed

M&L PCC (1:4:8) Type C-1 using 40mm graded stone aggregate) as in foundation filling complete all as specified and directed

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, base of columns and the like complete all as specified and directed

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate, as in columns, pillars, piers, posts, struts and the like complete all as specified and directed.

M & L for use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions in fair finished surface of concrete complete all as specified and directed.

S & F of framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer in charge.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick in ridges of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified and directed by engineer in charge.

Manufacturing, supplying and fixing retro reflective Overhead informatory road signage and boards, made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat ctivated retro reflective sheeting conforming to type - III of ASTMD- 4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame work including M.S. plate to be includes the cost .

M& L Chicken mesh used in plaster for beam and column provided with chicken mesh wire netting 25 gauge, 20mm mesh complete all as specified and directed

S&F rotational moulded polythylence water storage tanks 2000 Ltr cylindrical vertaical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 2000 ltrs including disconnecting the unserviceable existing tanks ferrule complete all as specified and directed

M&L in repairs Ball valve high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete 25mm dia complete all as specified and directed.

M&L Nipple suitable for HDPE water tank (minimum weight 25mm - 65 gms) 25mm bore dia complete all as specified and directed

Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore15mm complete all as specified.

S&F Steel water tubing medium grade galvanised with all fittings including short length , fixed to walls and ceiling and laid in floor complete with all fittings (such as bends, elbows, Tee , short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) of nominal bore dia 15mm complete all as specified.

Refixing and cleaning 15mm bore old serviceable steel tubing and connections in new or old position (Walls, ceiling, floors etc) complete all as specified and directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore20 mm complete all as specified. -

S&F Steel water tubing medium grade galvanised with all fittings including short length , fixed to walls and ceiling and laid in floor complete with all fittings (such as bends, elbows, Tee , short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) of nominal bore dia 20mm complete all as specified.

Refixing and cleaning 20mm bore old serviceable steel tubing and connections in new or old position (Walls, ceiling, floors etc) complete all as specified and directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore 25 mm complete all as specified. -

S&F Steel water tubing medium grade galvanised with all fittings including short length , fixed to walls and ceiling and laid in floor complete with all fittings (such as bends, elbows, Tee , short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) of nominal bore dia 25mm complete all as specified.

Refixing and cleaning 25mm bore old serviceable steel tubing and connections in new or old position (Walls, ceiling, floors etc) complete all as specified and directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore 40 mm complete all as specified. -

S&F Steel water tubing medium grade galvanised with all fittings including short length , fixed to walls and ceiling and laid in floor complete with all fittings (such as bends, elbows, Tee , short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) of nominal bore dia 40mm complete all as specified.

M&L stop valves 15mm bore dia, cast copper alloy fancy type, chromium plated with long shank and cup concealed type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions in repairs complete all as specified and directed.

M&L bib tap brass 15mm bore dia chromium plated long shank fancy type with curtch or butterfly handle , screwed down, screwed for iron pipes complete in repairs complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories)

S&F 160mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to walls etc complete all as specifed and directed.

S&F 110mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to walls etc complete all as specifed and directed.

S&F 160mm dia PVC bend any radius with or with out access doors etc, completed as specified and directed.

S&F 110mm dia PVC bend any radius with or with out access doors etc, completed as specified and directed.

S & F 110 mm bore PVC (SWR) Branch piece, single (single Y) equal or unequal of any radius with access door. completed as specified and directed.

S & F 110 mm bore PVC (SWR) Vent Cowl completed as specified and directed.

S& F readymade pulley operated clothes drying system incl of four aluminium pipes of 7 feet long each (4pipes) channel assembly locking system ropes and all fixing material complete all as specified and directed .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises.

M&L Non-Skid ceramic coloured tiles 7 to 8 mm thick (square/reactangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, in floor finishes set and joineted in neat cement slurry and pointed in white or colured cement to match over incl 10 mm thick screed bed in cement mortar 1:6 including finishing even and fair complete all as specified.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M& L for Rendering 10mm thick in (1:3) CM on fair faces of brick work or concrete surfaces of ceiling and finishing even and smooth without using extra cement complete all as specified and directed.

M&L for applying one coat of white cement based wall care putty on Ceiling, new or old surfaces of any description finished even and smooth complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling etc complete all as specified and directed

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangemen

Excavation in trenches not exceeding 1.5 Mtr wide and n. exceeding 1.5 mtr depth in soft / loose soil and getting out for removing / laying of pipe lines complete all as specified.

Returning and filling incl spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick all as specified.

Removing of surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified.

Supply and laying in trenches/fixing to wall/ceiling or floor,Jointing, GI tubing,medium grade including all fittings, such as bends,elbows,tees,unions,short pieces,connectors,check nuts,caps,plugs etc complete all as specified and directed for the pipe dia size 50 mm bore.

All as above item above but for the Pipe Dia of 40mm.

All as above item above but for the Pipe Dia of 25mm.

S & F Gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed suitable for 50mm inch GI pipe.

S & F Gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed suitable for 40mm inch GI pipe.

S & F Gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed suitable for 25mm inch GI pipe.

S&F in repairs 20 mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed

Material and labour for construction of valve chambers of size 900x900x900 mm suitable up to 100 mm Dia pipe (internal dimension built in brick masonary on 15cm thick PCC foundation(1:4:8) type D-2 using 40 mm graded stone aggregate over 100 mm thick hard cor with brick work masionary in cement mortar 1:4 using 'B' class bricks and rendering in cement mortar 1:4, 10 mm thick internally included exposed surface of external surfaces, MS cover made out of 3 mm thick MS sheet on iron angle framework made out of MS flat iron 25 x 6 mmx 300 mm long and 40 mm thick PCC coping 40 mm thick 1:2:4 type B-0 using 12.5 mm garded stone aggregate with handle hinges with locking arrangement & applying two coats of synthetic enamle paint over a coat of red oxide primer to all exposed steel surfaces complete all as specified and directed by the Engr-in-Charge.

Material and Labour for dry fine sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm thick after laying, stretching and testing the cable all as direted. Note : [Punned thickness 18 cm shall be measured & paid]

Supply and laying un-reinforced pre cast concrete cable cover, class LV type 1 with flat size 250mm x 150mm x 40mm

Supply & Laying XLPE insulated,Screened,PVC bedded galvanised steel strip or wire armoured,electric power cables with aluminium conductor with multistranded,1100 volts,grade cross sectional area 3.5Cx35 sqmm.Note : The Rate includes earth work,sand coushning,PCC covering etc.(D Zone DG set Panel To Pump Room Panel)

Supply and laying in trenches/fixing to wall/ceiling or floor,Jointing, GI tubing,medium grade including all fittings, such as bends,elbows,tees,unions,short pieces,connectors,check nuts,caps,plugs etc complete all as specified and directed for the pipe dia size 80 mm bore.

Supply, Install Testing and commissioning of Monoblock centrifugal pump set horizontal type suction / delivery with a discharge capacity-600 LPM, 40 mtr head, mechanical seal arrangement including 3-phase energy efficient squirrel cage induction motor as prime mover, 415 V, S1 duty rating, energy efficiency level -IE 3 BEE star rated, ISI Marked 10 HP (7.5 KW) 2900-3000 RPM as per IS- 12615 ( latest edition) fixed to pump through jaw type coupling with pump impellor of phosphorous bronze and shaft of carbon steel complete, including PCC foundation, base frame and cable connection complete all as specified and as directed.

M&L for sub main wiring complete four core 6.0 sqmm PVC insulated ,flexible cable unsheathed, heavy duty 1100 volts grade (FRLS) multi-stranded copper conductor cable ,drawn completely in and including PVC conduit concealed in walls/floors etc including with all accessories, fittings, PVC junction boxes etc, connected to common mains, and Motor Body terminals complete all as specified and directed. Note: 4cx6 Sqmm PVC FRLS flexible cable and one run of pvc conduit will be measured as "one unit"length.

S & F Foot valve made up of brass body of size 80 mm dia bore suitable for flanged type joint connection with motor suction pipe complete all as specified and directed.

Supply and fix in repairs Non Return valve Cast iron body flanged suitable for 80mm bore GI delivery pipe connection all as specified and directed.

Supply and fix sluice valve of size 80 mm dia with cast iron short body. Hand wheel with stainless steel spindle, checknut complete all as per IS -14846-2000 with nominal pressure rating, PN 1.6 including. material & labour for jointing flanged joint with rubber fibre jointing ring bolt nut & washer etc including necessary earth work. complete all as specified and directed

S & F Gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed suitable for 15mm(1/2") inch GI pipe.

Supply and Fixing on roof of pump House Rotational moulded polyethylene (PVC) Made water storage tank 500 Ltrs Capacity(cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed.

S & F water pressuge Guage meters Made with black steel case stainless steel roll ring plastic suitable for the pressure Range up to 7 KG/sqcm complete all as specified and directed.

Supply, installing, testing and commissioning factory made and tested LT Panel Indoor type, platform mounted, suitable for 415 Volts 3 Phase and neutral, 4 wire, 50Hz AC supply system. Shall be dust and vermin proof, protection class (IP-42) and made of 2.00 mm thick Stainless Steel Sheet SS316 & suitable frame work/ support made out of 50 x 50 x 6 mm MS angle frame, front and Rear opening type with space for cable entry from back side of the panel, with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 10 sqmm complete. ( Location:- Pump Room Panel ) Make:- HPL/ ABB/ L&T/ Universal Switch Gear Control/ Tricolite.Note :The contractor duly shall submit the Manufacturer'S Design and drawings of LT panel for approval of GE The scope of work also comprising of the following:-

BUS BAR CHAMBER :- (a) 100 Amp 4 Strips, Aluminium conductor, with color coded heat shrinkable sleave and shall be mounted on non hygroscopic, non combustible, track resistant, high strength DMC material, interconnection of all incomings & outgoings. INSTRUMENT CHAMBER :- (a) Digital Multimeter flush type rated -01 Nos,(b) C.T's 100/5 A CL 1.0 Tape Wound- 01 Set. (Set of three) (c) R,Y,B Phase indicating Lights LED type 220 V AC- 1 Set. (Set of three).(d) Protection MCB 6 A SP C Series- 1 Set. (Set of three). Make of Metering Accessories :-L&T/ AE/ Trinity/ Schneider. INCOMING SUPPLY :- (a) MCCB 63 Amps 16 KA ,4 Pole,adjustable thermal &magnetic release 415 volts ,50Hz,=01 No. OUTGOINGS :- 1. Star Delta Starter for 10 HP Rating Pumps -03 Nos Each having the following :- (a) MCB TPN 25 A 16 KA 4 Pole - 01 No (b) Power Contactor 22 A TP (Main & Delta) - 01 Nos,(c) Power Contactor 18 A TP (Star) - 03 No.(d) Bi Metal Over Load relay 9-15 A - 01 No.(e) Star delta timer Micon Series - 01 No.(f) Digital Amp Meter (0-30A) - 01 No.(g) CT 30/5A - 01 No.(h) Single Phase Preventer - 01 No,(i) Push button Start/Stop with Elements(set of 2) - 01 Sets,(j) On, Off, Trip indicating Lights LED type 220 V AC- 1 Set. (Set of three).(k) Aux. Blocks 1 No+1 Nc - 3 Set. 2. MCB SPN, 32 Amps 415v, 10 KA - 02 Nos. Make of Starter accessories :- L&T/ ABB/Legrand / Siemens/Schnider

Material and labour for earthing complete with GI earth plate electrode 600x600x6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground lavel) with top edge of the plate not less than 1.5mtr below normal ground lavel connected to GI earth strip 25X4 mm by mean of bolts, nuts, check nuts and washer of brash all as shown in electrical plate No 5 connected to earthing test point all as specified or indicated including PCC pit and CI cover fullel with watering pipe, wire mess and copper lugs etc GI protection pipe 40 mm dia medium grade including testing on completion all as specified and directed.(02 for Pumps Body, 02 For Pump Control Panel)

Deduct Credit for Demolished/ Dismantled material Rs. (-) 20140.00 (Minus) as listed in Schedule of Credit Note1: Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum' Note 2:- The tenderer must keep in mind when quoting rates against items out in multiple store house having height 4 mts to 7 mts. Necessary scaffolding and saftey measures required during execution of work are including in this items.

mp construction co

Vishal Builders