Construction of balance work of Ayurvedic Health Centre at Satrol, Tehsil Kandaghat, Distt. Solan H.P

Amount

Excavation in earth work in drains and channels in all depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock, with chiseling and wedging out of rock;(where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and as directed by the Engineer-in- Charge at site, according to the H.P.PWD. specification of 1990 (One thousand Nine hundred Ninety) volume-I and sorting out useful & unuseful materials and stacking the same in all leads and lifts and transportation of the unuseful materials for filling in roadways, embankments for grades improvement and leveling to required grades and then disposing of surplus excavated earth in acquired width of road or on approved dumping sites through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and all labour, machineries, materials, tools equipments and safety measures and incidentals necessary to complete the work by mechanized means and labour (if any required) .All useful materials, such as stones, shingles, aggregate and slates shall be sorted along road side to the maximum possible extent in all leads and lifts through all modes of transportation and other incidental charges. Any loss to the public and Any loss to the public and private property during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.

Excavation in earth work in drains and channels in all depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock, with chiseling and wedging out of rock;(where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and as directed by the Engineer-in- Charge at site, according to the H.P.PWD. specification of 1990 (One thousand Nine hundred Ninety) volume-I and sorting out useful & unuseful materials and stacking the same in all leads and lifts and transportation of the unuseful materials for filling in roadways, embankments for grades improvement and leveling to required grades and then disposing of surplus excavated earth in acquired width of road or on approved dumping sites through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and all labour, machineries, materials, tools equipments and safety measures and incidentals necessary to complete the work by mechanized means and labour (if any required) .All useful materials, such as stones, shingles, aggregate and slates shall be sorted along road side to the maximum possible extent in all leads and lifts through all modes of transportation and other incidental charges. Any loss to the public and Any loss to the public and private property during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.

Providing form work with steel plates 3.15 mm (Three point fifteen) thick welded with angle iron in frame 30x30x5 mm. (Thirty into thirty isto Five millimeter) So as to give affair finish ice centring , shuttering, strutting and propping etc. with wooden battens and bellies, height of propping and centring below supporting floor to ceiling not exceeding 4mtrs (Four meter) . And removal of the same for in situ- reinforced concrete & plain concrete work in ; Flat surfaces such as soffits of suspended floors,roofs landing and the like: Floors etc. upto 200 mm (Two hundred millimeter) in thickness:

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters,buttresses,plinth and string courses and the like.

Edges of slabs and breaks in floors and walls: (i) Under 20 cm. (Twenty centimeter) wide.

Providing and laying cement concrete 1:6:12 (one cement isto six sand isto twelve graded stone aggregate forty milimetre nominal size ) and curing complete excluding cost of centring and shuttering in as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials in all leads and lifts and asper the direction of Engineer-in-Charge.In foundation and Plinth in all depths and levels.

Providing and laying cement concrete 1:3:6(one cement isto three sand isto six graded stone aggregate fourty milimeter nominal size)and curing complete in foundation and plinths .

P/L cement concrete work in1:2:4 (one Cement isto two Sand isto four graded stone aggregate) 20 mm (Twenty millimeter) nominal size) & curing complete excluding cost of form work & reinforcement for reinforced concrete work in Stair case( except spiral stair cases) excluding landing but including preparing of the surface and finished of nosing up to floor to level.

Providing and laying cement concrete work 1:2:4 (one Cement isto two Sand isto four graded stone aggregate) 20 mm (Twenty millimeter) nominal size and curing complete excluding cost of form work and reinforcement for reinforced concrete work in : Walls (any thickness but not less than 0.10 ( Zero point Ten) metre thickness including attached pilasters buttersses,plinth and string courses etc. from top of foundation upto floor two level

P/L cement concrete work in1:1.5:3 (one cement isto one point five sand isto three graded stone aggregate 20 mm (Twenty millimeter )nominal size & curing complete excluding cost of form work & reinforcement for reinforced concrete work. Lintels, beams girders bressumers and cantilevers upto 1st floor level :Floors upto 200mm thick.

Wall (any thickness but not less than 0.10 m thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level upto 1st floor level :

2nd class Brick masonry work using common burnt clay building bricks in superstructure above plinth level up to 1st floor level. In Cement mortar 1:6 (one Cement isto six Sand).

2nd class Brick masonry work using common burnt clay building bricks in superstructure above 1st Floor Level to 2nd Floor Level. In Cement mortar 1:6 (one Cement isto six Sand)

2nd class Half Brick masonry in common burnt clay building bricks in superstructure above plinth level up to 1st floor level. In Cement mortar 1:4 (one Cement into four Sand).

Squared rubble masonry with hard stone of approved quality in foundation and plinth up to rquired level in cement mortor 1:6 (one cement is to six sand) as per direction of the Engineer-in-Charge and as per HP.PWD specification 1990 volume-I,

P/L Stone soling under floors.

Providing and fixing flush door shutters decorative type core of block board construction with frames of first class hard wood and well matched first class indian teak plyveneering with vertical grains or cross bends and face vencering on both faces of shutter. i/c all leads , lifts & carraige of material. 30 mm (Thirty millimeter) thick including black enamelled M.S. butt hinges

Providing and fixing 19 mm (Ninteen millimeter) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete)

Providing and fixing 1.00 mm (One millimmeter) thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete.

Providing and fixing 4 mm (four millimeter) thick water proof kit ply of standard quality ISI mark and approved shade and colour in wall lining i/e mitring at junction butt jointing and nails & screws etc complete) frame work for base to be measured and paid seperatly

Providing and fixing square edges cover fillets (beading) 19 mmx6 mm (Ninteen millimeter isto Six millimeter) sectionincluding mitring at junctions with wood screws and nails complete.(i) 1st class Deodar wood.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws. (i) 40 mm(Forty millimeter) Thick. 2nd class Deodar wood.

Providing and fixing M.S plain grills of required pattern in wooden frames of windows etc. with M.S flats square or rounded bars with round headed bolts and nuts or by screws as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I

Providing and fixing bright finished Aluminium sliding door-bolts with nuts and screws etc. complete. 300x15 mm(three hundred isto fifteen milimeter)

250x15 mm(two hundred fifty isto fifteen milimeter)

Providing fixing bright finished Aluminium tower bolts (barrel type) with screws etc. complete.200x10 mm(two hundred into ten milimeter)

150x10 mm(one hundred fifty into ten milimeter)

Providing and fixing bright finished Aluminium handles with screws etc. complete. 125mm

100 mm,(one hundred milimeter)

Providing and fixing 100 mm (Hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete

Providing and fixing bright finished hand drawn hooks and eyes. (a) 200 mm(two hundred milimeter)

Providing and fixing 12mm thick 150 mm (Twelve millimeter isto one hundred fifty millimeter) wide pelmet with 25 mm (Twenty five millimeter) diametre wooden curtain rods and brackets including fixing 25x3mm (Twenty five millimeter isto Three millimeter) M.S. flat at 10 cm. (Ten Centemeter) Long and plugs etc. complete. 1st class deodar wood.

Providing and fixing bright finished brass ball catcher 10 mm dia.

Providing and fixing bright finished brass heaps and stapples (safyt type) with necessary screws etc. complete. (i) 150 mm (one hundred fifty milimeter)

Providing and fixing 65x35mm (sixty five into thirty five)special quality chromium plated bright finished brass cup board locks with six leavers including screws complete Indian make.

Providing and fixing oxized MS double acting spring hinges with necessary screws etc. complete. (i) 100 mm (one hundred milimeter)

Providing and Laying Kota stone slab flooring 20mm average thickness 55x55 (Fifty five into fifty five) centimeter size having one shade only with white marble band 35cm to 40 cm (thirty five cm to fourty cm)wide on both sides of walls (to be mirror polished) thick base of cement mortar 1:4 (1 cement :4 sand) laid over and jointed with grey cement sluurry mixed pigment to match the shade of slab including rubbing and polishing complete. as per HPPWD Specification, including carriage of all labour equipment and material 25 mm thick.(twenty five milimeter)

Providing and laying Kota stone slab 25 mm(twenty five milimeter) (average) thick in rises, skirting, dado and pillars laid on 12mm (twelve milimeter.)average thick base of cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement sluurry mixed pigment to match the shade of slab including rubbing and polishing complete.as per HPPWD Specification,

White glazed tiles 6 mm ( six millimetre) thick in skirting risers of steps and dado on 12mm thick(twelve milimeter) cement mortar 1:3 (1cement isto 3sand) and jointing with neat cement slurry :-30x20cm( size thirty centimetre into twenty centimeter) as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I

Providing and fixing glass strips 40 mm(fourty milimeter) in joints of terrazo floors 40mm wide and 4mm thick(fourty milimeter into four milimeter thick)

Cement concrete flooring 1:2:4(one cement isto two sand isto four graded stone aggregate twenty milimetre)nominal size laid in one layer finished with a floating coat of neat cement as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials. 40mm(forty milimetre ) thick

Cement plaster skirting(upto 30 cm height) with cement mortar 1:3(one cement isto three sand)finished with floating coat of neat cement i/e rounding of junction with floor 20mm (twenty milimeter) thick.

Providing and laying 20 mm (twenty milimetre ) thick Makarana marble work ( table rubbed and polished) in flooring over 20 mm (twenty milimetre )thick base in cement mortor 1 : 3 (one cement : three sand) including jointing with cement mortor 1:2 ( 1 white cement : marble dust) with an admixure of pigment to match the shade of the marble ( size thirty centimetre into twenty centimeter) as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I

Providing and fixing 0.60 mm(zero point sixty) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20(twenty) microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm diametre with prepainted limput and rubber washer complete with all accesories as required as per the direction of Engineer-In-Charge.

Providing and fixing ridges or hips 60 cm (sixty centimeter)overall with 0.60 mm (sixty milimeter)thick cm overall with 0.60mm(sixty milimeter) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm diametre with prepainted G.I. limput and rubber washer complete with all accesories as required as per the direction of Engineer-In-Charge.

Providing and fixing valley 60 cm(sixty centimeter) overall 0.60mm(sixty milimeter) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm diametre with prepainted G.I. limput and rubber washer complete with all accesories as required as per the direction of Engineer-In-Charge.

Providing and fixing flushing 38 cm (thirty eight centimeters) over all with 0.60 mm (Zero point six zeromilimeter thick) prepainted steel sheet in roofing withhot dipped metalic zink coated sheets with top coat of regular modified polyster organic coating of 20(twenty) Microne over five micrones primer coating to back coat of polyster of five micrones over five micrones primer coating that is fixing with prepainted iron J or L hooks, bolts and nuts 6 (six) mm (Six milimeter) diometer with prepainted lempet and bitumen washers complete with all accesoriees as required as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I and levels and as per the direction of Engineer in charge.

Providing and fixing M.S. BP Sheet 1.66 mm to 2 mm (one point sixty six to two milimeter)thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base memmber of steel work shall be measured and paid separtely)

Providing mild steel/Tor Steel for R.C.C. work including bending, binding and placing in position complete.(b) Tor Steel.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint. including all leads , lifts & carraige of material. In beams,joists,channels,angel,tees,flats with connecting plates or angle cleats as in main and cross beams hip and jack rafters purlins connected to common rafters and the like

In gratings framed guard bars,ladders, railling, brackets and similar works

Providing and fixing steel glazed door windows and ventilators or standard rolled steel section welded with 16x3.5mm lugs 10 cm long embeded in cement concrete blocks 15cmx10cmx10cm size of 1:3:6 (one cement;three sand:six graded stone aggregate twenty milimetre)nominal size with wooden plugs and screws as required and iron fittings including P/F glass panes with glazing clips and special sesh putty as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-. Steel windows side hung windows

Steel ventilators top hung ventilators

Providing and fixing moulded hand rails of MS hollow pipe 50mm dia welded in straight length over MS flats at top of vertical balusters including one coat of red lead oxide priming coat complete(MS flat and balusters of railing shall be measured and paid seperately) .

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Painting two costs (excluding priming cost on new steel and other metal surfaces With enamel paint brushin to give an even shade (i) Enamel paint other than white :-

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting. (i) Readymixed paint brushing wood primer pink.

Painting two coats(excluding priming coat) on new wood and wood based surface with Enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping. (i) With enamel paint other than white

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and otther foreign matter etc. including sand paper smooth complete.

Wall painting (two coats) with acrylic emulsion paint of approved brand an manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and paper smooth including applying for of putty a required for metling the same. . Asian paint or equalent.

6mm Cement plaster to ceiling (b) In Cement Mortar 1:4 ( one Cement isto four Sand) including all leads , lifts & carraige of material.

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. (iv) Cement Mortar 1:6 (one Cement isto six Sand).

20mm(twent milimeter) cement plaster in two coats backing coat 10mm(ten milimeter) and finishing coat 10mm (ten milimeter)thick on fair side of brick/stone masonry walls for interior plastering upto floor two level including arrises internal rounded angles,chamfers and/or rounded angles (i) cement mortar1:4(one cement isto four sand).

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. (iv) Cement Mortar 1:6((one Cement isto six Sand).

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer. .

White washing with lime on ceiling and/or sloping roofs surfaces in all floors two coats to give an even shade including thoroughly brooming the surface to remove all dirt, dust mortar dust and other foreign matter as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I

Providing under layer for plinth protection of 75mm (seventy five milimeter)thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (one Cement isto three Sand six Graded stone aggregated 20mm nominal size)(twenty milimeter)

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm(fifteen isto twenty two centimeter) in cement mortar 1:6 (one Cement inti six Sand) and inside plastring with cement plaster 1:3 (one cement isto three sand). (1 Cement:3 Sand) including earth work and laying 10 cm(ten centimeter) cement concrete i

Supplying of Cast Iron Cover without frame for mainhole. (i) For frame of internal dimension 455 x610 mm(four hundred fifty five into six hundred ten) rectangular C.I. cover 9Light Duty single seal pattern-1) the weight of cover to be lot less than 23 kg.(twenty three Kilogramme)

Providing and fixng to wall ceiling floor galvanised mild steel tubes medium grade tube fittings and clamps including making good the wall ceiling and floor(Earth work in trenches to be measured and paid for separately)as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I 15mm (fifteen millimetre) nominal bore :-

Providing and laying in trenches, galvanised mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) :- 20mm twentymillimetre) nominal bore :-

25 mm nominal bore(twenty five milimeter)

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm(twenty milimeter isto twenty milimeter) nominal bore by providing and fixing tee including cutting and threading the pipes complete.

Fixing water meter stop-cock in galvanised mild steel tube including necessary fittings such as mild steel galvanised jam nut, sockets, etc. cutting and making long screws complete (water metre and stop-cock to be measured and paid for separately) (i) 25 mm nominal bore

Constructing chamber 300 mm x 300 mmx500 mm (Three hundred isto three hundred isto five milimeter) for stop cock the C.I.Surface box 100x100x100 mm(one hundred into one hundred into one hundred) inside with hinged cover fixed in cement concrete slab 1:2:4 mix (one cement two sand four graded stone aggregate 20mm nominal size)75mm thick foundation concrete (seventy five milimeter) thick foundation concrete 1:5:10 (one cement five sand grades stone aggregate 40 mm nominal size)(fourty milimeter) and inside plastering with cement mortar 1:3 (one cement three sand) finished with a floating coat of neat cement including curing complete . including all leads , lifts & carraige of material.(i) With 100 mm. (one hundred milimeter)Cast in situ plain cement concrete walls in 1:2:4 mix (one cement two sand four grades stone aggregate 20 mm nominal size)(twenty milimeter)complete with form work.

Providing and fixing vitreous China wash down, water closet (Indian type. W.C. pan) with integral 'P' or 'S' trap size 580mm earth work bed concrete foot rest and trap to be measured and paid seperately .

Providing and fixing vitreous china wash down, water closet (European type W.C. pan) with integral P or S trap including jointing the trap with soil pipe in cement morter 1:1 (one cement isto one sand)(Seat and overto be measured and paid for separately ) Angle indian universal closet .Anglo indian :-20004 size 58x40x30cm(fifty eight into fourty into thirty centimeter)Cera/Hindware company

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers : . (1) Solid Type: (a) White plastic seat and cover

Providing and fixing vitreous china bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp(waste pipe to be measured and paid for seperately) of size 633x395x420 mm with automatic flushing system with fitting of Cera or its equivalent.No 60001 (sixty thousand one)of cera.

Providing and fixing squating plate for Urinals 450mmx350(four hundred into three hundred fifty milimeter) with integril urinal flush pipe .

Providing and fixing PTMT coloured /white high density/polythene/poly propelyne 10.00(ten) litre capacity (full flush)European standard control low level flushing cistern with a pair of C.I. BRACKETS with fittings such as lead valve with polythene flot with push buttons coupling for connections with complete with inlet outlet and overflow pipes 40mm dia CP flush bend etc.complete No 2603 (two thousand six hundred three)of CERA/HINDWARE.

Providing and fixing C.P.Brass flush pipe spreaders for urinal with fittingsuch as unions clamps etc(all in brass).15mm nominal size.

Providing and fixing vitreous china wash basin with single hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fittings flat back 550mmx400mm (five hundred fifty into four hundred millimetre) No. 1025(one thousand twenty five) without pedestal of Cera or its equivalent. No 10001 size 550x400(ten thousand one size five hundred fifty into four hundred).

Providing and fixing vitrious China pedestal for wash basin complete recessed at the back for reception of pipe and fittings

Providing and fixing C.P. Brass waste for wash basin or sink :- (i) 32 mm dia.(thirty two milimeter)

Providing and fixing 600 mm x 450 mm (six hundred isto four hundred fifty milimeter)bevelled edge mirror of superior glass mounted on 6 mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws :- (i) 750mm x 20mmm(seven hundred fifty into twenty milimeter)

Providing and fixing 600 mm x 120 mm (Six hundred isto one hundred twenty milimeter)glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P Brass screws.

Providing and fixing Toilet paper holder. (a) C.P Brass

Providing and fixing chromium plated ISI marked is no. 8934 of ESS/ESS or its equalent brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws.

Providing and fixing C.P. Brass bib tap with capstan head (i) 15 mm (fifteen milimeter)dia ISI marked no 8934 of ESS/ESS.

Providing and fixing C.P. Brass Pillar tap with capstan head (i) 15 mm (fifteen milimeter)dia ISI marked no 8934 of ESS/ESS.

Providing and fixing C.P. Stop cocks (i) 15 mm (fifteen milimeter) dia

Providing and fixing C.P. Stop cocks (i) 20 mm (twenty milimeter) dia

Providing and fixing C.P. Stop cocks (i) 25 mm (twenty five milimeter) dia

Providing and fixing C.P. Brass angle valve (i) 15 mm (fifteen milimeter)dia ISI marked no 8934 of ESS/ESS.

Providing and fixing C.P. Stop cocks (i) 15 mm (fifteen milimeter) dia

Providing and fixing mixer for kitchen sink with casted swinging swinging spot at top

Providing and fixing PVC connection pipe(heavy duty ISI marked IS:8931 & 8934) with brass union 45cms. (forty five centimetre) Length 15mm (fifteen millimetre) nominal bore

Providing and fixing 15mm(fifteen millimetre) nominal bore brass fullway valve with wheel .

Providing and fixing G.I./M.I. Union of following sizes :- (i) 15 mm dia.(fifteen milimeter)

20mm nominal dia(twenty)

25mm nominal dia(twenty five)

Polyethylene (PE-AL-PE) composite pressure pipe U.V. stabilizedm with carbon black confirming to IS-15450-2004(fifteen thousand four hundred fifty-two thousand four) water supply including clamp at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall. Internal work-Exposed on wall. 1216 (16 mm O.D. pipe)(one thousand two hundred sixteen)

Providing and fixing composite end seal compression fittings as per IS-15450-2004(fifteen thousand four hundred fifty-two thousand four) for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. Equal Tee 1216(one thousand two hundred sixteen)

1620(one thousand six hundred twenty)

Reducing Tee.1620 x all branches.(one thousand six hundred twenty)

Female branch Tee.1216 X 1216 X 15 mm thread.(one thousand two hundred sixteen isto one thousand two hundred sixteen isto fifteen milimeter)

1620 X 1620 X 20 mm thread((one thousand six hundredtwenty isto one thousand six hundred twenty isto twenty milimeter)

Female elbows:- 1216 X 15 mm thread.(one thousand two hundred sixteen isto fifteen milimeter)

1620 X 15 mm thread.(one thousand six hundredtwenty isto twenty milimeter)

Male thread connector:- 1216 X 15 mm thread.(one thousand two hundred sixteen isto fifteen milimeter)

1620 X 15 mm thread.(one thousand six hundredtwenty isto twenty milimeter)

1216 X 15 mm thread.(one thousand two hundred sixteen isto fifteen milimeter)

1620 X 15 mm thread.(one thousand six hundredtwenty isto twenty milimeter)

Couplers:- 1216(one thousand two hundred sixteen milimeter )

1620(one thousand six hundredtwenty milimeter)

Reducers 1620x1216 (one thousand six hundred twenty milimeter into one thousand two hundred sixteen milimeter)

2025x1216 (two thousand twenty five milimeter into one thousand two hundred sixteen milimeter)

Providing and fixing PVC water storage tank ISI marked of approved brand and make (Sintex or equivalent) with 40mm (forty milimetre) nominal bore galvanised mild steel scour tube with fitting, 25mm(twenty five milimetre) nominal bore galvanised mild steel over flow tube with fittings and mosquito proof coupling of approved municipal design 15mm (fifteen milimetre) nominal bore ball valve and cover with locking arrangement providing pads of required sizes for inlet and outlet etc. complete including hoisting at roof level height (i)1000 litres (one thousand)net capacity tank capacity tank .

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. 110 mm x 90 mm(one hundred ten isto ninty milimeter) complete.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete. 110 mm dia.(one hundred ten milimeter)

150 mm dia.(one hundred fifty milimeter)

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete. 110 mm dia.(one hundred ten milimeter)

75 mm dia.(seventy five milimeter)

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete. 110 mm dia.(one hundred ten milimeter)

75 mm dia.(seventy five milimeter)

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete 110 mm dia.(one hundred ten milimeter)

75 mm dia.(seventy five milimeter)

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete. 110 mm dia.(one hundred ten milimeter)

75 mm dia.(seventy five milimeter)

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 110 mm dia.(one hundred ten milimeter)

75 mm dia.(seventy five milimeter)

Providing and fixing PVC offset 45, ISI marked including fixing with approved adhesive etc. complete 110 mm dia.(one hundred ten milimeter)

75 mm dia.(seventy five milimeter)

Providing and fixing PVC double equal branch with oval access door, ISI marked insertion rubber washer 3mm(three milimeter) thick bolts and nuts complete including fixing with approved adhesive etc. complete . 150mm(one hundred fifty milimeter) dia . including carriage of material .110 mm dia.(one hundred ten milimeter)

Providing and fixing PVC clamps ISI mark of approved design including fixing with approved adhesive etc. complete

Providing and fixing PVC 'P' or 'S' trap for water closet (squatting pan ) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete 110mm(one hundred ten) dia.

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S Brackets painted white including cutting holes and making good the same but excluding fitting (i) 610 x 460 mm with bowl depth 200 mm.(six hundred ten into four hundred sixty into two hundred milimeter)

Providing and fixing PTMT jet spray of approved quality and colour with one meter tube.

Providing and fixing 100mm dia chromium plated grating of superior quality for floor gully or nahni trap

Construction of mainhole with R.C.C. top cover 1:2:4 mix in (one cement two sand four graded stone aggregate 20mm nominal size)(twenty milimeter) foundation concrete1:4:8 (one cementfour sand eight graded stone aggregate 40mm nominal size)(fourty milimeter) inside plastering 15mm(fifteen milimeter) thick with cement mortar 1:3 (one cement three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (one cement two sand four graded stone aggregate 20mm nominal size)(twenty milimeter) finished smooth complete including curing and testing: Inside size 800 mm x 800 mm and 500 mm (eight hundred isto eight hundred isto five hundred milimeter)deep including C.I cover with frame. (Light duty Single seal pattern - 1) 455 mmx610mm (four hundred fifty five isto six hundrded ten milimeter)internal dimensions total weight of cover and frame to be not less than 38kg. (thirty eight)(Weight of cover 23 kg(twenty three) and weight of frame 15 kg.)(fifteen Kg) With 200 mm (two hundred milimeter)cast in situ plain cement concrete walls in 1:2:4 mix (one cement two sand four graded stone aggregate 20mm nominal size) (twenty milimeter)complete with form work

Supplying and fixing cast iron cover without frame for main hole internal dimension 455mmx610mm rectangular(four hundred fifty five into six hundred ten milimeter) rectangular C.I. cover light duty single seal pattern-1 the weight of cover to be not less than 23kg(twenty three ).

Providing and fixing cast iron cover 300x300 mm(three hundred into three hundred milimeter) with frme and gully trap the weight of cover to be not less than 4.53 Kg(four point fifty three).

Cutting holes upto 15cmx15cm in RCC floors and roofs for passing drain pipe etc. and repairing the holes after insertain of drain pipe etc. with cement concrete 1:2:4(one cement two sand four graded stone aggregate 20mm nominal size)(twenty milimeter)

Cutting holes through existing brick work including making good the same in (1) holes upto including 400Sqcm in area cement mortar 1:6(one cement isto six sand) per cms depth of cutting.

Providing and fixing water pump to lift rain water .

Providing and fixing 40mm CP grab bar 40mm dia steel pipe 78cm height MS plate waste pipe

Jitender Kumar