Construction of New Assam type Building for Dimoria Co District Office along with development of surrounding area,providing boundary wall,Transformer,DG with shed,CCTV and networking works at Sonapur,Kamrup M,Assam.Civil, Sanitary and Electrical work

Amount

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 15.12.1 Of area 3 sq. metres and below

Dismantling cement asbestos or other hard board ceiling or partitionwalls including stacking of serviceable materials and disposal ofunserviceable materials within 50 metres lead.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling roofing including ridges, hips, valleys and gutters etc.,and stacking the material within 50 metres lead of: 15.28.1 G.S. Sheet

Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : 15.14.1 Of sectional area 40 square centimetres and above

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 15.7.4 In cement mortar

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2.8.1 All kinds of soil.

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : 16.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.5 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.3 Suspended floors, roofs, landings, balconies and access platform

Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing andreinforcement - All work up to plinth level : 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand)

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 13.5.1 1:4 (1 cement: 4 coarse sand)

13.4 12 mm cement plaster of mix : 13.4.1 1:4 (1 cement: 4 coarse sand)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 21.1.1 For fixed portion , 21.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 9.1.2 Sal wood 9.1.2 Sal wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 9.9.1 Second class teak wood .9.9.1.1 35 mm thick

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural ources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 11.41A.2 Glazed vitrified floor tiles polished finish of size 11.41A.2.1 Size of Tile 600 x 600 mm

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size 11.41A.3.1 Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). 11.47.2 Size of Tile 600x600 mm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. completeat all levels. 8.2.2 Granite stone slab colour black, Cherry/Ruby red 8.2.2.1 Area of slab upto 0.50 sqm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm ---- compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.2 Hot finished seamless type tubes

Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 wit characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 12.65.2 0.71 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm.

Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm with 3mm thick EPDM seal and SS plain washer complete :12.66.1 Precoated/mill finish aluminium Ridges plain (500- 600mm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 13.43.1 Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : 13.60.1 Two or more coats on new work

Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.50 Applying priming coat:13.50.1 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :13.61.1 Two or more coats on new work

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement, 13.9.2 20 mm cement plaster

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 16.91.2 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size-- all heights as per specifications, drawings and as directed by Engineer-in-charg .12.52.2 GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.3 White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 18.52.1 15 mm nominal bore

Providing and fixiand fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.2 Rectangular shape 453x357 mm

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 18.22.2 150 mm diameter

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.2 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.18.50.1 15 mm nominal bore

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 12.41.2 110 mm diameter

12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.42.5 Bend 87.5° 12.42.5.2 110 mm bend

12.42.4 Single tee without door 12.42.4.2 110x110x110 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 18.8.1 15 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 18.9.2 20 mm nominal dia Pipes

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Boring/drilling bore well of required dia for casing/ strainer pipe, bysuitable method prescribed in IS: 2800 (part I), including collectingsamples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools,plants & machineries required for the job, all complete as per directionof Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 23.1.1.1 300 mm dia

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ dia bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.Rocky strata including Boulders, 23.1.2.1 300 mm

Supplying, assembling, lowering and fixing in vertical position in borewell, ERW (Electric Resistance Welded) FE 410 plain slotted (havingslot of size 1.6/3.2 mm) mild steel threaded and socketed/ plainbevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than5.40 mm, including painted with outside surface with two coats ofanticorrosive bitumestic paint of approved brand and manufacture,including hire & labour charges, fittings & accessories, all complete,for all depths, as per direction of Engineer -in-charge.23.11.3 200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing ofjoints complete as per direction of Engineer in Charge. 18.9.5 40 mm nominal dia Pipes

Providing and fixing wall panelling interior partition walls , colmn chowkath etc.---. as directed and specified by the deptt

Providing fitting fixing PVC panels for wall and ceiling(plain) with material installation including labour, carriage etc as directed and specified

Supplying, fitting and fixing Johnson Roller Blinds (Swiss Roller) make and shade, design as per choice complete as specified and directed by the department at all levels.

Supplying, fitting and fixing Toughened glass partition with sliding arrangement with SS steel frame upto a ht. of 2.108m made of 12mm Tinted glass with all accessories etc. complete and as directed.

Supplying and fitting 4.5 kg Capacity CO2 type fire extinguisher with labour as directed by the department for Ministers' Colony Quarter,Dispur,Guwahati-6

Supplying and installation of office Furniture (Workstation ) (Model Max 1) at Sub District office of Dimoria as directed and specified by the Department.

Supplying and installation of office Furniture (Workstation table) (Model Max 7) at Sub District office of Dimoria as directed and specified by the Department.

Supplying and installation of office Furniture (Workstation Chair) at Sub District office of Dimoria as directed and specified by the Department.

Supplying and installation of Poly Carbonate sheet 10 mm thick 4 layer at Co District office of Dimoria as directed and specified by the Department.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 way (4 + 24), Double door

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 3 Module

6 Module

12 Module

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A, 16 KA,TPMCCB

250 A, 25 KA,TPMCCB

100 A,30KA,FPMCCB

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Double pole

Triple pole and neutral

Supply, installation Testingand Commissioning of 1200mm sweep BEE 5 star rated, ceiling fan with Brush Less Direct ccurrent (BLDC) Motor class of insulation B 3 nos. blade ,30cm long down rod, 2 nos. canopies shackle kit safety rope copper winding, Power Factor not less than 0.9 service value (CMM/W) minimum 6.85, Air deliveery minimum 215CMM, 350RPM (Tolerance as per IS 374-2010 THD less than 10% remote or electronic.regulator unit ofr speed contron and all remaining accessories incluidng safety in, nut,bolts washers, temperature rose =75 degree C (max) insulation resistance more that 2 mega ohm, suitale for 230 v, 50Hz single phase AC supply earting etc. complete as required.

Supplying with installation testing and commissioning of Hi-wall 3 Star rating not ducted split type air conditioner of the following capacity with cordless remot compleete with copper pipe and electrical connection cable as approved by the Deptt. Up to 5m between the room unit and outdoor unit as directed by the Deptt.1.5 Ton capacity (Voltas/Carrier/Blustar/Daikin make )

Supplying with installation testing and commissioning of Hi-wall 3 Star rating not ducted split type air conditioner of the following capacity with cordless remot compleete with copper pipe and electrical connection cable as approved by the Deptt. Up to 5m between the room unit and outdoor unit as directed by the Deptt.2.0 Ton capacity (Voltas/Carrier/Blustar/Daikin make )

Supplying with fitting and fixing Voltaz Stabilizer of the following specification complete including making necessary connection as approved , specified and directed by the Deptt. (SKYLAND/VEE DEE/ V-Guard/VERTEX/ INDO/VENUS make) 5 KVA

Supplying installation testing and commissioning of the following tube light Phillips 22 Watt/2200 lumen 6500 K LED Tubelight Phillips (ECOLINK 22 Watt) Luminaire complete with all accessories with necessary support with 1.5 sq.mm PVC insulated S.C. copper conductor as required and as directed by the Deptt. (Phillips/Jaquar/L.T./ Wipro make) Phillips 22 Watt/2200 lumen 6500 K LED Tubelight Phillips (ECOLINK 22 Watt )

Supplying insstallation testing and commission of following Ballasted LED Lamps for General Lighting Service 9 watts Luminaire complete with all accessories with necessary support with 1.5 sq.mm P.V.C. insulated by the depatment (Phillips/Jaquar/L.T/Wipro make) Ballasted LED Lamps for General Lighting Service 9 watts

Supplying installaiton testing and commission of the follorwing indoor decorative Reces mounted LED down light luminaries of 14w Led Recessed Luminaire Phillips complete with all accessoried such as balast starter etc. in the false ceiling type Armstrong /Gypsum or similar ceiliing mounting with necessary support with 1.5 sq.mm PVC insulalted S.C. Copper conductior as required and as directed by the Deptt. (Phillips/Jaquar/LT/Wipro make) 4W Recessed LED Down Light

Supplying installation tsting and commissioning of Exhust fan 225mm air flow as rquired 1.5sq.mm copper mulstrand wire connection an as specified and directed by the Deptt. Orient/Usha/Crompton make

Supplying and testing and commissioning of 16mm 4 core Aluminium Armored Power Cable as specified and directed by the Deptt. Polycab/ Finolex/RR make. 16mm 4 core Aluminium Armored Power Cable

Supplying and testing and commissioning of submersible Pump Set Fillox Pump single phase submersible pump set 1.5 HP as specified and directed by the Deptt. Submersible Pump set Single phase withmotor rating of 1.5 HP

Supplying and testing cpmmissioning of Crompton ARMOR 1.5 HP starters control panel for submersible Pump as specified and directed by the Deptt. Crompton ARMOR 1.5 DSU 1.5 HP Starters control Panel for submersible Pump

Supplying and testing and commissioning of Submersible Flat Cables for Submersible as specified and directed bythe Deptt. Capital 3 core copper (EC grade) Submersible flt cables for submersible Pumps capital (CAPITAL 3 CORE 2.5 SQ.MM SUBMERSIBLE CABLE)

Supplying, installation testing and commissioning of the following rating copper wound indoor / out door type transformer complete including the payment to be made to power supply authority for supervision charge, labour charge, cost of L.T/H.T metering etc. (excluding the cost of load security) and making necessary arrangement for charging approval of the sub-station from the competent authority as directed and specified by the department. Transformer should be as per CEA guidelines as ammended up to date upto 200 KVA star rating up to 5 star, above 200KVA as per CEA guidelines for losses along with LV enclosure. 11/0.4KV 100 KVA DTR Copper Wound BSI Level -2

Supplying with errection of 1x70 sq mm AAAC covered conductor complete with including making necessary connection as approved, specified and directed by the deptt.1Cx70 Sq mm AAAC Covered Conductor.

Supplying with laying of 3.5 Core 95.0 Sq mm U.G Cable specified and directed by the deptt.3.5 Core 95.0 Sq mm armoured U.G. Cable.

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical outdoor type double door, floor mounting compartmentalize panel board of size 1.25M X0.6MX 0.40M made of 16 SWG1.66 m thick C.R. sheet and 35mm X 35mm X 5mm size angle having 4 no legs at the bottom and C.R. sheet roofing on the top. The panel board is to be erected in 1 : 3 : 6 PCC foundation including excavation of trench and brick soling etc. complete neatly Wiring done with provision for one no 125/160A 4pole MCCB or Switch Fuse Unit as incomer and provision for 2nos DP or TPN out going as specified and directed by the deptt. confirming to IP 65 protection comprising of the following electrical items:

Supplying with fitting and fixing of 12 METER LONG STEEL TUBULAR POLE 410-SP-66 complete with including making necessary connection as approved, specified and directed by the deptt.250 KVA Level II Transformer

Supplying with errection of 11KV 150A GOAB switch cum horn type fuse complete with including making necessary connection as approved, specified and directed by the deptt.11KV 150A GOAB switch cum horn type fuse

Supplying with fitting and fixing of 3Ph 4W Combined CT/PT Accuracy Class 0.5,15/5A,STC 6.4 KA for 1Sec with including making necessary connection as approved, specified and directed by the deptt. 3Ph 4W Combined CT/PT Accuracy Class 0.5,15/5A,STC 6.4 KA for 1Sec

Supplying with fitting and fixing of Disc Insulator(Porcelain) 45 KN (T&C) Type complete with including making necessary connection as approved, specified and directed by the deptt.Disc Insulator(Porcelain) 45 KN (T&C) Type

Supplying with fitting and fixing of Pin Insulator (Plymer) 5KN (FRP 24mm) complete with including making necessary connection as approved, specified and directed by the deptt.Pin Insulator (Plymer) 5KN (FRP 24mm)

Supplying with fitting and fixing of GI Channel Cross Arm(100x50x6x3200mm) complete with including making necessary connection as approved, specified and directed by the deptt.GI Channel Cross Arm(100x50x6x3200mm)

Supplying with fitting and fixing of 11Kv 5KA lighting Arrestor ( Line Type, Distribution Class) complete with including making necessary connection as approved, specified and directed by the deptt.11Kv 5KA lighting Arrestor ( Line Type, Distribution Class)

Supplying with fitting and fixing of 11KV DO Fuse Set 150A Assembly complete with including making necessary connection as approved, specified and directed by the deptt.11KV DO Fuse Set 150A Assembly

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying including installation, testing and commissioning of Air/Water Cooled Diesel Generator set coupled to suitable alternator of 220/415 V, AC, 1/3-Phase 0.8 p.f.(la mounted on a 1) M.S. Fabricated base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) AMF Control Panel.5) Suitable batteries with lead.,5) First fill of lube oil.,6) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer. (RANGE FROM 5 KVA TO 625 KV . Kirloskar green/bliss, Leyland, Volvo Penta, Perkinson, Mahindra, Greaves, Escort engine and Kirloskar, Stamford, Leroy somer or equivalent alternator.

Load Security to be paid APDCL Authority LOAD SECURITY CALCULATION Applied Load = 55 KW

Supply of 4MP Entry IR Fixed-focal Bullet Network Camera .4-MP 1/3" CMOS image sensor, low luminance, and high definition image. · Outputs max. 4 MP (2560 × 1440)@30 fps. · H.265 codec, high compression rate, ultra-low bit rate. · Built-in IR LED, and the max. illumination distance is 30 m. · DWDR, 3D NR, HLC, BLC, digital watermarking, applicable to various monitoring scenes. · ROI, SMART H.264+/H.265+, flexible coding, applicable to various bandwidth and storage environments.· Built in Mic 12 VDC power supply, easy for installation. IP67 protection. (Make Dahua/ Honeywell/Hikvision)

Supply of 4MP Entry IR Fixed-focal Dome Network Camera 4-MP 1/3" CMOS image sensor, low luminance, and high definition image. · Outputs max. 4 MP (2560 × 1440)@30 fps. · H.265 codec, high compression rate, ultra-low bit rate. · Built-in IR LED, and the max. illumination distance is 30 m. · DWDR, 3D NR, HLC, BLC, digital watermarking, applicable to various monitoring scenes. · ROI, SMART H.264+/H.265+, flexible coding, applicable to various bandwidth and storage environments. · Built in Mic 12 VDC power supply, easy for installation. IP67 protection. ( Make Dahua/ Honeywell/Hikvision)

Supply of 32 Channel 1U 4K&H.265 Lite Network Video Recorder 4K Resolution The NVR supports 4K ultra HD resolution (3840 x 2160) for recording, live viewing and playback. H.265/H.264 codec decoding Max 200Mbps Incoming Bandwidth Up to 8MP Resolution for Preview and Playback HDMI/VGA simultaneous video output Support ANR technology to enhance the storage reliability when the network break down ( Make Dahua/ Honeywell/Hikvision)

Supply of 6 TB Surveillance Internal Hard Drive HDD Digital Storage Capacity 6000 TB Hard Disk Interface Serial ATA Connectivity Technology SATA Brand Seagate Special Feature Lower Power Consumption, Reliability with D Hard Disk Form Factor 3.5 Inches Compatible Devices Camera Installation Type Internal Hard Drive Hard Disk Size 6 TB ( Make Seagate/ Western Digital Purple/Toshiba )

20-Port Unmanaged Gigabit Switch with 16-Port PoE Ethernet Port Rate 1 Gbps Optical Port Rate 1 Gbps Number of Bussiness Card Slots Port 1–16: 16 × RJ45 10/100/1000 M (PoE) Port 17–18: 2 × RJ45 10/100/1000 M (uplink) Port 19–20: 2 × SFP 1000 M (uplink) Power Supply 100V AC–240V AC Operating Temperature –10°C to 55°C (14°F to 131°F) (Make Dahua/ D-link/ Tplink )

Supply of 55 inch 4K UHD Display 400 nits Brightness builtin Android Quadcore Processor 24 X7 Operational ( Make Panasonic / Sony/ LG )

Patch Panle 24 Port Loaded

Patch Cord 1Mtr

RJ 45 Connector

PVC BOX

6u RACK Loaded

2u RACK Loaded

Supply of Active Optical HDMI Cable 4K, ( Make: Cable-Wise/Purelink / Atlona )

Supply of CAT6 UTP Cable supports Gigabit Ethernet (1000 Base-T) standard. Operates at a bandwidth up to 250 Mhz. This cable well exceeds the requirements of TIA/EIA-568.C.2 Category 6 ISO/IEC Class E, 23 AWG solid copper conductor for superior conductivity, Resistance Unbalance : 5% Max ( Make: Belden / D-Link/ Molex}

Supply of Various Connectors, and Accessories

Installation and Commissioning Charges

Supply of 65" Intelligent Flat Panel Display Brightness (typical) 450 cd/m², Resolution 3840 x 2160, Response Time (typical) 8 ms, Viewing Angle 178 x 178, Surface Hardness Toughened Glass with Level 7 of MOHS Standard, Panel Technology IPS, Operating System Android 13, CPU Quad core processor and with 1.9Ghz (A55×4), Memory 4 GB, Storage 32 GB, WiFi and Bluetooth Wifi 802.11ac/b/g/n/a/axBT 5.2, Type of Touch Technology 40 touch points, Accuracy ±1.5mm, Interactive White Board Software Support in Androide and Windows*, Features Writing, Pen, Palm Eraser, Save, Screen Capture, Storage and Tool Bar. Supports 3rd party applications, recording feature, USB WEB Cam Compatible, Support PPT, Word,PDF, Image, Video Pla, Product Dimensions (WxHxD) 1488.4×896.6×87.2mm ).(Make Panasonic/ LG/ Viewsonic)

Supply of OPS PC, i5 Processor Includes Windows 11 Pro Operating System, 6GB RAM, 128 GB ROM

Supply of Captivate USB / Bluetooth Speakerphone USB, Bluetooth®, and analog audio connectivity 360-degree coverage captures voices in up to a 16 foot (5 meter) radius 6-element microphone array focuses audio pickup and suppresses background noise Sophisticated acoustic echo cancellation and noise reduction ( Make Atlona/Purelink / Lightware)

Supply of Captivate™ 4K ePTZ Auto-Framing Camera USB-C®interface for video and audio, as well as device powering Automatically detects and re-frames camera for up to 6 participants 4x digital zoom and 110° wide horizontal field of view Fast, responsive ePTZ (electronic pan, tilt, and zoom) camera functions 2-microphone array with 5 meter (16 foot) audio pickup range.( Make Atlona/Purelink / Peoplelink)

Supply of HDMI Cable - 2,00m, HDMI-A male to HDMI-A male , HDMI version 2.0 – 18Gbps for resolutions up to 4K UltraHD 60Hz , High purity, tinned OFC copper conductors and triple shielding, AWG28 , Gold plated precision contacts with PureLink SLS™ (Secure-Lock-System™).( Make: Aten/Purelink / Atlona )

Supply of Active 4K Premium High Speed HDMI Cable 7,50m, HDMI-A male to HDMI-A male with PureLink APO™ , HDMI version 2.0 – 18Gbps for resolutions up to 4K UltraHD 60Hz , High purity copper conductors and triple shielding, AWG28. ( Make: Aten/Purelink / Atlona )

Supply of USB 3.2 USB-C Cable with E-Marker – 2.00m , USB 3.2 (Gen 2x2) – 20Gbps data transmission , Gold plated precision contacts , USB-C male to USB-C male , High purity copper conductors and triple shielding ,E-Marker, USB Power Delivery 100W, DP Alt-Mode up to 8K 30Hz ( Make: Aten/Purelink / Atlona )

Supply of Various Connectors, and Accessories

Installation and Commissioning Charges

2 Meter Moulded Conference Cable

10 Meter Moulded Conference Cable

Supply of Digital SmartMixer®with acoustic echo canceller and web interface, Onboard acoustic echo cancelling (AEC) 12-band parametric EQ SmartMix modes with gain sharing or gating options 4 balanced mic inputs, 2 balanced Mic/Line inputs and 1 stereo unbalanced input 1 stereo and 2 mono outputs 2-channel USB audio interface for soft codec (Skype, WebEx) integration or playback from computer Full digital processing on inputs and outputs 8 x 3 audio routing matrix 6-channel Smart Mix (gate or gain sharing) Front panel direct operation and Web Remote functionality IP control for third-party CCS administration Up to 6 mixers can be linked using Cat5e cable. (Make: Audio-technica / Midas / Allen & Heath)

Supply of 5" Compact Monitor Speaker Type: Passive 2-Way Monitor speaker Driver Size : 1 x 5.3” LF & 0.5" HF Driver RMS Power : 25 W Nominal impedance: 4 Ohm Frequency Range (-10 dB) : 70 Hz to 20 kHz Dispersion : 150° (H) x 115°(V) Degree Sensitivity: 86 dB Maximum SPL : Peak - 100dB Enclosure: ABS 757 Steel grill Included Accessories : Wall mount bracket (Make Tannoy / Renkus Heinz / Fohnn Audio)

Supply of 4 Channel 300 Watt Power Amplifier with ATR Class D Power Handling : 4 × 65 W @ 4 Ohms, 4 × 45 W @ 8 ohms THD 20Hz-20kHz at 1 W <0.3% RMS Power Bridged Mode : 130 W @ 8 Ω, 2 pairs of channel Bridged. Frequency Response : 20 Hz to 20 KHz Connection : Input - 4 x XLR / ¼ " TRS combojacks , Output : 4 x locking-style connectors Input Impedence : 10kΩ unbalanced,20kΩ balanced Signal to Noise Ratio : 100 dB Voltage Gain : 28 dB Damping Factor : > 80 @ 8 Ω Should have Power, Signal and Clip LEDs to monitor performance ( Make Behringer/ Labgruppen / Powersoft )

Supply of 98" LED Display in 16:9 Aspect ratio with 30% Haze, Slim DLED Display, Brightness 600 cd/m2, Viewing Angle 178°, Android 11 OS, 24x7 operational, Built in wifi & Bluetooth, Quad core A55 CPU, MaliG51 MP2 GPU, 4GB RAM, 32GB ROM, HDMI 2.0 x 3, HDMI output x 1, Audio output x 1, Optical output x 1, USB 2.0 x 1, USB 3.0 x 1, USB type C x 1, RS232 x 1, LAN x 2, Built in speaker 2x 12W, 80 PIN OPS slot, wifi slot, Power 340W, Operation Temperature: 0oC - 45oC, smart features: inbulit signedge, built in chromecast, auto wakeup on input ( Make Panasonic/ Sony/ LG)

Supply of Wireless Presentation Platform Wireless AV platform allows simultaneous content sharing for up to four 1080p presenters Wireless screen casting with iOS®, AndroidTM, Mac®, ChromebookTM, and Windows® devices through native AirPlay®, Google CastTM, or MiracastTM protocols Dynamic Layout ModeTM (patent pending) automatically adapts to incoming or disconnected source content Instructor Mode allows a user to manage content, adjust audio volume, upload and play media content, stream YouTubeTM, and switch between layouts Supports YouTube Live streaming Supports cloud-based digital signage platforms Local storage available for playback of images and video ( Make Atlona/Purelink / Lightware)

Supply of Cable Cubby with 1 x HDMI , 1 X USB-C, 2 x LAN and 2 x Power Connections

Supply of 12U AV Equipment Floor mount Rack 600 X 600

Supply of HDMI Cable - 2,00m, HDMI-A male to HDMI-A male , HDMI version 2.0 – 18Gbps for resolutions up to 4K UltraHD 60Hz , High purity, tinned OFC copper conductors and triple shielding, AWG28 , Gold plated precision contacts with PureLink SLS™ (Secure-Lock-System™). ( Make: Cable-Wise/Purelink / Atlona )

Supply of Active Optical HDMI Cable 4K, Connector HDMI Type A, Transmission Bandwidth 18 Gbps, Display Resolution 4K@60hz, HDMI Version HDMI 2.0, Wire Specification Optical Fiber + Copper Cable for Power, Power Consumption 250mW, Operating Temperatures -40°C to 70°C, Other Features eARC|VRR|QFT|ALLM Dynamic HDR, ( Make: Cable-Wise/Purelink / Atlona )

Supply of CAT6 UTP Cable supports Gigabit Ethernet (1000 Base-T) standard. Operates at a bandwidth up to 250 Mhz. This cable well exceeds the requirements of TIA/EIA-568.C.2 Category 6 ISO/IEC Class E, 23 AWG solid copper conductor for superior conductivity, Resistance Unbalance : 5% Max ( Make: Belden / D-Link/ Molex}

Supply of 1.5 MM 2 Core Speaker Cable

Supply of 20/22 AWG Microphone/Signal Cable ( as per actual)

Supply of Various Connectors, and Accessories

Installation and Commissioning Charges

SWITCH CISCO GIGABIT CBS 350 WITH CBS 350-24P-4G

Cisco ISR series 1G Router with Care Pack & License

RACK 22 U Standalone Rack with Accessories

CABLE CAT 6 D-LINK

KEYSTONE JACK CAT 6 D-LINK

FACE PLATE SINGLE D.LINK

BACK BOX D-LINK

Patch Cord

UPS 6 KVA WITH BATTERY 26 AH 0.30 hr backup

CASSING & CAPING 2.'

Cisco Lan SFP

lnstallation

15Amp/5amp Electric Socket & Switches along with wirring for server room

Trolley Rack and connecting cables for UPS Battery

M/s Pawan Communications Private Limited (BID ID -263997)

GANPATI CONSTRUCTION COMPANY (BID ID -264451)