PERIODICAL SERVICES IN OTM OMQS BLDGS (ZONE-I) WELCOME MAINTENANCE FOR B/R NATURE IN DOMESTIC OMQS AREA AT AF STN BHISIANA

Amount

Taking down cement or cement lime plaster of any description and any thickness on brick ,concrete or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed by Engineer in charge.

M&L for rendering 15 mm thick cement plaster in CM (1:4) on fair faces of brick or concrete surfaces and finishing the surface even and fair etc. complete all as specified and directed by Engineer in charge.

M&L for rendering 10 mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and fair etc, complete all as specified and directed by Engineer in charge.

M&L for rendering 5 mm thick cement plaster in CM(1:3) on fair faces of concrete surfaces in ceiling , complete all as specified and directed by Engineer in charge.

M&L for rough cast plaster on brick wall consisting under coat of cement and sand mortar (1:4) not less than 10mm thick and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel mixed with coarse sand and cement in the ratio 1:1:1 shall be applied and finish even, complete all as specified and directed by Engineer in charge.

M&L for prepration of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed by Engineer in charge.

M&L for preparation of old decorated surfaces of ceiling and applying one coats of white wash, complete all as specified and directed by Engineer in charge.

M&L for prepration of new plastered surfaces of walls and applying three coats of white wash, complete all as specified and directed by Engineer in charge.

M&L for preparation of old decorated surfaces of walls and applying one coats of white wash, complete all as specified and directed by Engineer in charge.

M&L for Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper acrylic/distemper oil emulsion acrylic, white or tinted over a coat of primer of same make, complete all as specified and directed by Engineer in charge.

M&L for preparation of old decorated surfaces of walls and applying one coats of oil bound distemper acrylic/ distemper oil emulsion acrylic, white or tinted, complete all as specified and directed by Engineer in charge.

M&L for complete removal of existing treatment and preparation of old plastered surfaces of walls and applying two coats of Oil bound distemper acrylic /distemper oil emulsion acrylic, white or tinted over a priming coat of same make on wall surfaces, complete all as specified and directed by Engineer-in-Charge.

M&L applying 1-2 mm thick wall care putty (JK White/Birla White /Berger) on walls, including making surface even and smooth using sand paper before applying Priming coat, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of walls, pillars, cornices and applying Two coats of premium quality exterior emulsion paint over priming coat of exterior primer complete all as specified and directed by Engineer-in-Charge. Make :- Asian (Apex), Nerolac (Excel Anti Peel), Berger (Weathercoat Anti dust)

M&L for preparation of old decorated surfaces of walls, pillars, cornices by brooming down etc and applying one coat of premium quality exterior emulsion paint complete all as specified and directed by Engineer-in-Charge. Make :- Asian (Apex), Nerolac (Excel Anti Peel), Berger (Weathercoat Anti dust)

M&L for Complete removal of existing treatment on old plastered surfaces of walls, pillars, cornices and applying Two coats of premium quality exterior emulsion paint complete all as specified & directed by Engineer in Charge. Make :- Asian (Apex), Nerolac (Excel Anti Peel), Berger (Weathercoat Anti dust)

M&L for a coat of Exterior primer with alkali resistant on walls over old/new bricks or conc surfaces complete all as specified & directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of cement base primer on new plastered surfaces complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old decorated surfaces of walls and applying one coats of cement base paint, complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and preparation of old plastered /unplastered surfaces of walls and applying two coats of cement base paint over a coat of cement base primer complete all as specified and directed by Engineer-in-Charge.

M&L for repair to RCC ceiling, sunshades, Chajjas, Balconies, Columns, bands, beams, roof slab and similar RCC work at any position/height by dismantling loose/disintegrated portion and dubbing out with Cement Concrete 1:1½:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel U clamps made out of 8mm dia @ 150mm c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with10 mm thick plastering in CM 1:4 finished even and fair without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed by Engr-in-Charge. Note : The Extra area of 300mm around the actual affected area will be checked and repaired and only repaired portion will be taken for measurement.

M&L Preparation of old wooden surface and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer in Charge.

Material and labour for preparation of old steel surfaces of any description not otherwise described over 10cm width or grith and applying one coats of synthetic enamel paint over, complete all as specified and directed by Engineer in Charge.

M&L for preparation of previously treated/untreated surface of chequred or interlocking tiles and applying two coats of indigo washable floor paint over a coat of priming paint with 30-40% water, complete all as specified and directed by Engineer in Charge.

M&L for preparation of old painted surfaces of concrete/kerb stone and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer in Charge.

M&L for preparation of old painted surfaces of wall and applying one coat of plastic emulsion paint complete all as specified and directed by Engineer in Charge.

M&L for Finishing walls with texture paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm complete all as specified and directed by Engineer in Charge.

M&L for Non woven matt wall paper in approved designs as directed by Enge-in-Charge (Eco friendly/latex saturaed 30% recycled 70% renewable cellulose fibres) suitable for residential and interiors having width of rol 76.20 mm and fixed on wall with approved adhessive with an overlapping of 5 cm complete all as specified and directed by Engineer in Charge.

M&L for complete removal of existing paint on unevenness waterfall fountain surfaces/small boulder surfaces & applying two coat of Latex/Acrylic Paint in different colours shades over primer of same make as per direction of GE including minor repair work/sealing of joints works etc complete all as specified & directed by Engineer in Charge. (Note : Unevennes fountain surface measured flat for payment, bidders are requested to visit the site before coating the rates)

S&F 110 mm bore PVC (SWR) pipes (Medium duty) single socketed in any length with rubber ring joints fixed to walls/floor with and including clamps, nut bolts including dismantling of old outlet pipe etc. complete all as specified & directed by Engineer in Charge.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified & directed by Engineer in Charge.

M&L for providing precast cement concrete louvres and jallies 25mm thick type B0 (1:2:4 using 12.5mm graded aggregate), (measured solid), set in cement mortar 1:6 including all mouldings etc complete all as specified and directed by Engineer in charge.

S&F in repairs Drizzle colour fully transparent high grade ABS corner shelve of size of 27x27x36 cm fixing with free screw and wall plug complete all as specified and directed by Engineer in charge.

Hacking out old broken glass any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins / spring clips and providing and fixing new ones complete all as specified and directed by Engineer in charge.

S&F sheet glass 4mm thick ordinary quality and glazing with oil putty or fixed with wooden beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed by Engineer in charge.

S&F figured glass 4mm thick, pin head type and glazing with oil putty in square not exc. 0.5 Sqm in each pane complete all as specified and directed by Engineer in charge.

S&F in repair curtain rails, mild steel, chromium plated including fixing brackets, both ends decorative nobs, rollers etc. , complete all as specified and directed by Engineer in charge.

Demolition of Brickwork or stone/ boulder masonary, built in cement mortar or cement lime mortar, complete all as specified and directed by Engineer in charge.

Material and labour for brick work with subclass B bricks, straight or curved on plan exc 6 m mean radius , buit in cement mortar (1:6), complete all as specified and directed by Engineer in charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specifed and directed by Engineer in Charge.

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. including 15mm thick screed bed in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specifed and directed by Engineer in Charge.

M&L for vitrified tiles 10 mm thick light shade (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:4) for laying floor finishes, complete all as specifed and directed by Engineer in Charge.

M&L for vitrified tiles 9 to 10 mm thick light shade (square/ rectangular) on vertical surfaces as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in CM 1:4 to receive vertical tiles complete all as specifed and directed by Engineer in Charge.

M&L for Glazed ceramic coloured tiles in vertical surface 350x250x7 mm / 450x350x7mm thick including 10mm thick cement plaster in CM 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specifed and directed by Engineer in Charge.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar, complete all as specifed and directed by Engineer in Charge.

Material and labour for Granite (of any Type) work table rubbed and polished 18-20 mm thick machine cut,in steps, jams,pillars,window cills,cooking platforms and like laid and bedded over 15 mm thick cement mortar in CM(1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to macth with shade of granite, complete all as specifed and directed by Engineer in Charge.

Rounding the edge of stone slabs one edge such as in steps, cooking platforms, and the other simmilar situation , complete all as specifed and directed by Engineer in Charge.

S&F in repair PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed by Engineer in charge.

M&L 15 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors , complete all as specified and directed by Engineer in charge.

Fixing only 15 mm dia steel tubes any grade to walls and ceilings or laying in floors, including new fittings as required, complete all as specified and directed by Engineer in charge.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed by Engineer in charge.

Material and labour 20 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed by Engineer in charge.

Fixing only 20 mm dia steel tubes any grade to walls and ceilings or laying in floors, including new fittings as required , complete all as specified and directed by Engineer in charge.

Cutting chases, pining in making good to facing where required and pointing in cement mortar 1:3 for concealed water tubing , cutting not exc 10 cm girth , complete all as specified and directed by Engineer in charge.

Dismantling PVC Water tanks Exc 500 Ltr and n exc 1000 Ltr and removing to store, complete all as specified and directed by Engineer-in-Charge.

M&L for three layered white colour Rotational moulded polyethylene water storage tanks of 1000 ltr Capacity (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, complete all as specified and directed by Engineer-in-Charge.

M&L for 20mm Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed as in repairs, complete all as specified and directed by Engineer-in-Charge.

M&L Vitreous china squatting pan , 'Orissa' pattern, size 580 x 440 mm white , with integral foot rests complete including provision of lime concrete bedding fixed as in repairs, complete all as specified and directed by Engineer-in-Charge. Make :- Hindware Cat Part No-20042/ Parryware Cat Part No-WPC0117CS1C/ Prayag Cat No- Range-E

S&F in repair china wash down water closet padestal pattern white excluding flush and fix to position, including seat cover and connection to drain etc complete all as specified and directed by Engineer-in-Charge. Make:- Hindware Cat Part No-524525/ Parryware Cat Part No:-WPC02781C/ Prayag- Glecy

S&F in repairs Health Faucet with Wall Hook, Chromium Plated having 1.00 Metre long with Hose Pipe, complete all as specified and as directed by Engineer in charge. Make :- JAQUAR/ ESSCO/ PRAYAG

S&F Brass Chromium Plated Toitet Paper Holder 150mm in size with Rod to hold Paper Roll and fixed-in-repairs, complete all as specified and as directed by Engineer in Charge. Make:- Prayag Cat Part No BA-08/ Hindware Cat Part No-F880003CP/Jaquar Cat Part No:-AHS-1551.

S&F in repairs glass corner shelf suitable size made of 5mm thick toughned glass all as specified. Make: Jaquar/ Prayag/ Prima/ Essco

S&F in repair PVC valveless , syphonic action type , flushing cistern, low level ,white, with inlet, ball valve, float and handle,completewith flush pipe of polythelene of low or high density or PVC 32 mm dia , including brackets / fastening assesoriesof 10 litres capacity, complete all as specified and as directed by Engineer in Charge.

S&F in repair for mirror cabinet of min size 430x330 mm with openable door shutter as approved by GE, omplete all as specified and as directed by Engineer in Charge.

M&L Vitreous China wash basin, white , flat back,size 550x400mm fixed on brackets or stands , including 32 mm waste coupling of PTMT (half or full threaded)/ CP Brass and corrugated waste pipe with adopter of 900 mm long, fixed in repair, complete all as specified and as directed. Make:- HINDWARE/ PRAYAG/ JAQUAR

S&F in repair wash hand basin Brass CP wall mixture 15mm bore for mixing hot and cold water screwed down for 15 mm iron pipe and fixed , complete all as specified and directed. Make- Hindware Cat Part No-F280009/ Parryware Cat Part No-T1315A1/ Jaquar/ Prayag.

S&F in repair 15 mm dia bore CP angular stop cock with wall flange cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed by Engineer-in-charge. Make :- Jaquar/ Essco/ Prayag

S&F in repair 15 mm dia bore CP concealed stop cock/Angle valve cast copper alloy chromium plated with long sahnk , fancy type,screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed by Engineer-in-charge. Make :- Jaquar/ Essco/ Prayag

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450mm, complete all as specified and as directed by Engineer in Charge.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm, complete all as specified and as directed by Engineer in Charge.

S&F in repair, 15 mm dia Bib taps , fancy type Chromium plated , screwed down , screwed for iron pipe or for brass ferrule.complete all as specified. Make :- Jaquar/ Essco/ Prayag

S&F in repair, brass CP Wall mixer 2 in 1, 15 mm bore, for mixing hot and cold water, screwed down for iron pipe and fixed ,.complete all as specified. Make- Jaquar/ Essco/ Prayag

S&F in repair, wall mounted goose neck sink mixer( Hot and Cold) with provision of swivel arm , connecting legs and wall flanges,complete all as specified. Make- Jaquar/ Essco/ Prayag

S&F in reapirs 15mm dia Pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and flu-nuts screwed for iron pipe complete all as specified and directed by Engineer in charge. Make- Jaquar/ Essco/ Prayag

Supply and Fixed in repair, Brass Chromium plated shower rose 125 mm size with or without swivel joints,including fixing to steel pipe or union , complete all as specified and directed by engineer in charge. Make :- Jaquar/Essco/Prayag

S&F in repair, stainless steel soap dish ,complete all as specified and directed by Engineer in Charge.

S&F in repair, Brass CP tubular towel rail of 20 mm dia, D type ,60 CM long between flange, complete all as specified and directed by Engineer in Charge.

S&F in repair Kitchen Plate rack with of size 750x900x250mm of stainless steel, complete all as specified and directed by Engineer in Charge.

S&F in repair coat hooks of six pegs made out of stainless steel 45 cm long (as per sample) , complete all as specified and directed by Engineer in Charge.

S&F in repair 20 mm dia stainless steel polished 204 grade drapery rod/curtain rod 1 to 2mm thick with finals decorative, including fixing of brackets and both ends decorative nobs, complete all as speccified and directed as per approved sample by Engr-in-Charge.

Taking down Chowkhats or frames/ steel windows/ventilators, not exc 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed by Engineer in Charge.

Taking down shutter of area exc 1 sqm but n exc 2 sqm each complete all as specified and directed by Engineer in Charge.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification and drawing, complete all as specified and directed by Engineer in Charge.

S&F Factory made solid panel PVC door shutter 30mm thick (stile), consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drawimg, complete all as specified and directed by Engineer in Charge.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed by Engineer in Charge.

S&F 125 mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer in Charge.

S&F 100 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer in Charge.

S & F for Anodised aluminium frame for doors, windows ventilators (Powder Coated) with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge.

S&F Powder coated Anodised aluminium side hung /sliding type window and ventilator shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, locks, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed by Engineer in Charge.

M & L sheet glass ordinary quality 5.5mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc 0.5 sqm each pane all corner of glass to be fixed with silicon complete all as specified and directed by Engr-in-Charge.

Supply and fixing Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tack or galvanised wire staple complete all as specified and directed by Engineer in Charge.

S&F Powder coated aluminium decorative grill of size of mesh 75mm fixed with doors, window for safety of glass etc. complete all as specified and directed by Engineer in Charge.

Taking down chowkats & shutters without taking off shutters from the frame, size of opening exc. 1.50 sqm but not exc 4 sqm each complete all as specified and directed by Engineer in Charge.

S & F Pressed steel frames for doors with one or more rebates including necessary fixing lugs,hinges, lock strike plate, etc complete all as specified and directed of size 125 X 60mm complete all as specified and directed by Engineer in Charge.

S & F Pressed steel frames for doors with one or more rebates including necessary fixing lugs,hinges, lock strike plate, etc complete all as specified and directed of size 105 X 60mm, complete all as specified and directed by Engineer in Charge.

M&L for PCC (1:3:6) type C-1 using 20 mm graded agg as in back of pressed steel chowkhatsetc complete all as specified and directed by Engineer in Charge.

S&F, Factory made, 35mm thick plain framed panelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces using 2nd class HW as in rail and style. The size of rail and style as per IS-1003 (part – I), kiln seasoned and chemically pressure treated, complete all as specified and directed by Engineer in Charge.

S&F 35mm thick glazed and skelton shutter IInd class hard wood ,open rebated and prepare to receive glass, gauge etc. (without sash bars) edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of member of shutters as specified in SSR part-1 , section 8 , clause 8.24(a) . complete all as specified and directed by Engineer in Charge.

Taking down shutter of any description exc 1.00 sqm but not exc 2.0 sqm each and refixing in same opening after easing and adjusting (Chowkat/frame changed) etc , complete all as specified and directed by Engineer in Charge.

S&F 150 Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer in Charge.

S&F 300 mm aluminium ally, anodised , sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed ,complete all as specified and directed by Engineer in Charge.

S&F 150 mm extruded Aluminium alloy handles, fabricated type anodised, complete all as specified and directed by Engineer in Charge.

S&F floor door stopper of size 140 mm of aluminium ally body and tongue, anodised, with hard drawn steel spring ficed in floors complete all as specified and directed by Engineer in Charge.

S&F in repairs mild steel 300mm ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed by Engineer in Charge.

S&F in repair of Aluminium body door cill upto 1mtr length at bottom part of door to stop entry of insect inside the room complete all as specified and directed by Engineer in Charge.

GUPTA AND ENGINEERS