PROVN OF UTENSILS WASHING POINT IN THE COOK HOUSE OF SHELTER NO 8112 AT DURBUK AND OTHER SANCTIONED WORKS AT TANGSTE AND DURBUK UNDER GE 860 EWS

Amount

Dismantling wall & ceiling boards (fibre, insulation etc ) or insulation boards, slabs, blankets any thick ness including cover fillets.

M&L 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in ceiling

M&L 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

M&L for preparing of old wooden surface/ old ply wood and applying one coats of synthetic enamel paint .

Dismantling of timber fillet under 40 Sq cm in section in framed work.

M&L second class hard wood timber scantling plain fillets, square, rectangular or triangular in section clear swan, sectional area exc 13 sqcm & not exc 25 sqcm, secured with nails or brads.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L screed bed or bedding layer of cement mortar 15 mm thick for laying floor finishes in CM (1:6)

M&L for non skid ceramic coloured tiles 7 to 8mm thick (Square/ rectan-gular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and joint in neat cement slurry and pointed in white or coloured cement to match.

Dismantling plain or corrugated steel sheetying any guage, thickness including nainital or similar pattern roof covering and wall cladding complete.

S&F of 0.50 mm CGI sheeting of class 7 with two corrugation side lap fixed with 'L' or 'J' hooks in roof/ wall cladding etc.

M&L for two coat of synthetic enamel paint over a coat of red oxide on new steel surfaces of any description, not otherwise described over 10cm width or girth after preparation complete.

M&L for one coat of synthetic enamel paint on old steel surfaces of any description, not otherwise described over 10cm width or girth after preparation complete.

M&L for 75 mm thick PCC (1:3:6) type C2 (using 40 mm graded stone aggregate) as in plinth protection/ path and fininshed and fair without using extra cement.

Taking down shutters of any description exc 1 Sqm and not exc 2 sqm each.

Taking down shutters of any description not exc 1.0 Sqm each.

M/L for glazed and skelton shutters 30 mm thick 2nd class hard wood, open rebated and prepared to receive glass, guage, etc, divided in to square with plain, chamfered or rounded mitred and rebated sash bars, any numbers, all as specified.

S&F for 40 mm thick flush shutters solid core construction, with block board core and plywood face panel commercial type on both sides.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section.

S&F 75 mm long aluminium anodised barrel tower bolt of extruded section.

S&F 250 mm long, aluminium alloy, anodised, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheets, cast or extruded section & fixing bolts and sliding bolts of extruded section all as directed by Engr-in-charge.

S&F MS butt hinges med weight cold rolled 100mm long.

All as per item No 22 above but 75mm long.

S&F 125 mm long Mild steel pressed handles,oval type stove enamelled black.

All as per item No 24 above but 100 mm long.

M&L sheet glass ordinery quality 3 mm thick and glazing with oil putty or wooden beads n. exc 0.50 sqm in each pane.

Taking up or down GI/Steel water tubing and connection incl cleaning for refixing or removal 15 mm bore complete alll as specified

S&F GI Tubes med grade, galvanised with all fittings, complete fixed to walls or laid in floors all as specified 15 mm bore complete alll as specified

Taking up or down GI/Steel water tubing and connection incl cleaning for refixing or removal 20 mm bore complete alll as specified

S&F GI Tubes med grade, galvanised with all fittings, complete fixed to walls or laid in floors all as specified 20 mm bore complete alll as specified

Lagging to GI pipes 15mm bore with 25mm thick bonded mineral wool preformed (SNAP ON) pipes section of density 144 Kg/Cum conforming to IS 9842 with chicken mesh wire netting 25 gauge, 20mm mesh complete alll as specified

Dismantling of water tanks & removing to stores exc 250 but not 500 ltrs capacity complete alll as specified

M&L for precast cement concrete 1;3;6 type C-1 ( using 20mm graded stone agg. ) as in block masonry for OHT for bathrooms and washing points with solid blocks exc 10 cm in width and set in CM 1:6 complete all as specified and directed by engr-in-Charge.

S&F rotantional moulded polythylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top ) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 20mm bore omplete all as specified and directed.

S&F Ball brass valve 20 mm bore, high pressure with polythene ball & float complete all as specified.

S&F stop valve cast copper alloy with crutch or butterfly handle screwed down, screwed both ends for iron pipes or brass furrel 20 mm bore complete alll as specified

S&F stop valve cast copper alloy with crutch or butterfly handle screwed down, screwed both ends for iron pipes or brass furrel 15 mm bore complete alll as specified

S&F Bib Taps cast copper alloy fancy type chromium plated crutch or butterfly handles screwed down, screwed for iron pipes or brass furrel 15 mm bore. complete alll as specified

S&F WHB Vitrous China coloured flat back size 550x400mm excl taps waste chains and plugs complete all as spd

S&F in repairs Vitreous China Wash Down WC squating Pan 'Orisssa pattern size 580x440 mm coloured with integral footrest (excluding flushing cistern and flush pipe incl P or S trap of CI) fixed in repairs.

Supply only PVC syphonic action type flushing cistern 10 ltr capacity, low level, coloured, with inlet, ball valve, float and handle incl flash pipe, brackets complete alll as specified

S&F Vitreous china Urinal bowl, flat back,size of 465x355x265mm white minium with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securign urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement (excluding flushing cistern, flush pipe) and waste pipe with discharge arrangement complete all as specified fixed in repairs.

S&F urinal spreader of PTMT of any colour for fixing with 15mmdia pipe complete all as specified and directed.

S&F Pillar taps cast copper alloy fancy type with capstan head, screw down, screwed for iron pipes 15 mm bore.in repairs complete alll as specified

M&L CI floor trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) 100 mm dia complete alll as specified

Mild steel deformed or twisted bars 10 mm dia cut to length bent to shape required, including cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia as in stirrups. complete alll as specified

M&L for RCC 1:2:4 type B1 (using 20 mm graded aggregate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, conopies, deck slabs and in shelves and the like incl all as specified

Dismantling of PVC drain pipes jointed in cement mortar and taking out of trenches if reqd and removed from site.

M&L 100mm bore PVC soil waste and bends pipe in any length with or without ear with cement joint fixed to wall and to floor all as specified .

M&L 75mm bore PVC soil waste and bends pipe in any length with or without ear with cement joint fixed to floor all as specified .

M&L 50mm bore PVC soil waste and bends pipe in any length with or without ear with cement joint fixed to wall all as specified .

S&F 100mm PVC bends,( any radius),diminishing pieces or tapers (larger bore measured)complete all as specified.

S&F for Glass shelf of size 600x120mmx5.5mm thick glass with CP Railling complete all as specified.

S&F for CP Brass tubular Towel rail 20 mm dia & 600mm long complete all as specified (Make- Sikko/Prayag)

Excavation in trenches n.exc 1.5M wide and n.exc 1.5M depth and n.exc 10 Sqm on plan and getting out in any kind of soil complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 ( Nominalmix) using 40 mm graded stone aggregate as in foundation filling and similar work complete.

Returning filling in incl spreading leveling, watering, and well, ramming in layer nexc 25 cm in layers complete all as specified.

Removing excavated material to a distance n. exc50 m and depositing where directed at a level n. exc 1.50 m above the starting point.

M&L for Rendering 15mm thick in cement mortar 1:6 on PCC block walling or concrete surfaces, finished even and smooth without using extra cement complete.

M&L for Rendering 15mm thick, in cement mortar 1:4 on PCC block walling or concrete surfaces and finished even and fair without using extra cement complete.

M&L for preparation of new plastered surface of walls and applying two coats of white wash including preparity to plastered surface for distempering complete all as specified and directed.

M&L for preparation of new plastered surface of of walls and applying two coat of cement base paint on walls complete all as specified and directed.

M&L for joist, channel, angle, or tee section,fe 410-w (gde - 250 quality - A) fixed independently, without connecting plate etc. (cut to ordinary lengths i.e with in 20mm of the length indicated complete all as specified and as directed.

S&F 0.63 mm Galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with 'L' or 'J' or cranked hook bolts in lieu of screws fixed in roof/ wall cladding etc complete all as specified and as directed.

M&L for two coat of synthetic enamel paint over a coat of red oxide on new steel surfaces of any description, not otherwise described over 10cm width or girth after preparation complete.

Formwork to soffits of suspedded slabs such as roof slabs, floor slabs landings and similar work ,vertical or to batter for rough finished flat surfaces of concrete complete.

M&L for rough finished formwork to edges of concrete flats, treads, break in floors, window cills, concrete railings, floor and roof n.exc 20 cm wide and side of RCC/ PCC band in walls, horizantal or sloping or similar work exc 10 cm but n. exc 20 cm wide.

M&L TMT bars 10mm dia and over in reinforcement cut to length bent to shape required incl hooking ends and binding with MS wire (annealed) not less than 0.9mm dia all as directed and specified.

M & L for providing RCC M- 25 in Slab supported in walls beams and columns in roof ,Landing, balconies, deck slabs and in shelves and similar work complete all as specified and as directed.

S&F sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washer and wastes, including in cement mortar to dwarf wall or including fixing cantilever brackets and connnecting union to pipe over all size 915mmx460mm bowl size 410mmx330mmx160mm with all fitting and fixture complete all as specified and directed fixed in repairs .

M& L for cement concrete 75mm thick type D - 2 using 40mm graded stone aggregate as in sub base to receive floor finish etc complete all as specified.

M& L for cement concrete 40mm thick type B - 1 using 20mm graded stone aggregate over sub base to receive floor finish etc complete all as specified.

S & F non skid ceramic coloured tiles 7 to 8mm thick (square or rectangular) area of each tiles exceeding 0.0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match, over 15mm thick screed bed in CM (1:6) compled

S&F for Glazed ceramic coloured tiles in vertical surface 300x200x7mm thick , set and jointed in neat cement slurry and pointed in coloured cement to match tiles over 10mm thick backing coat in cm 1:4 complete.

M&L for Sand cushioning to underground cable complete all as specified in clause 19.75 of SSR Part - I.

Taking out existing unserviceable LT PVC aluminium conductor cable, laid in trenches, ducts along the walls, through pipes, under road of following sizes including disconnecting and depositing in MES store yard complete all as specified and directed ;- (a) 50 Sqmm 3.5 core

(b) All as per item No 77 above but 35 Sqmm 3.5 core

(c) All as per item No 77 above but25 Sqmm 3.5 core

(d) All as per item No 77 above but16 Sqmm 4 core

(e) All as per item No 77 above but 10 Sqmm 2 core

Supply and laying XLPE insulated armoured heavy duty electric cable with aluminium conductor (Stranded) 1100V grade cross-sectional area 50 Sqmm 3.5 core laid in trenches or passing through pipe or fixed on pole etc complete all as specified and directed by Engr-in-Charge.

all as per item No 82 above but 35 Sqmm 3.5 core complete all as specified and directed by Engr-in-Charge.

all as per item No 82 above but 25 Sqmm 3.5 core complete all as specified and directed by Engr-in-Charge.

all as per item No 82 above but 16 Sqmm 4.0 core complete all as specified and directed by Engr-in-Charge.

all as per item No 82 above but 10Sqmm 2.0 core complete all as specified and directed by Engr-in-Charge.

Taking out unserviceable/serviceable cable cover and keeping at safe place for segregation of serviceable and un-serviceable cable covers all as directed at site.

Laying only un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick retrived from item ser No 88 complete all as specified.

Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified.

Supply, installation, testing and commissioning of LT control panel, cubical type, factory made, outdoor type, dust and vermin proof, fabricated out of mild steel sheet of thikness 3.15 mm and mild steel angle iron 50x50x6mm thick (frame) complete with front and rear openable shutters in having proper locking arrangement, sufficient space for cable placement and between MCCBs, Isolators including 04 Nos legs made out of angle iron 75mm x 75mm x 6mm thick, height of each leg shall be 75 cm duly grouted in PCC. Panel shall be spray painted internally and externally with two coats of synthetic enamel paint over a priming coat of red oxide primer and pre wired with suitable size of PVC insulated sheathed copper conductor cable complete in all respects and comprising of following accessories/fittings :-

(h) Aluminium bus bar of capacity 300 amps four strip with colour coding should be shrinkable sleeves 4 Nos fixed on insulators-01 Set of four Note : Unit rate quoted by the contractor here-in-before also includes for installation of panel on suitable PCC foundation and PCC plat form incl necessary earth and PCC work all as per manufacturer instructions and as directed by the Engr-in-Charge.

Supply and fixing in replacement tube medium grade galvanized with all fitting and fixed complete to walls/ poles/ ceiling or laid in floor of size 40 mm bore for the protection of UG cables including dismantling/ taking out old, unserviceable one complete all as specified and as directed.

Replacement of UNSV Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth strip 32x6mm by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 40 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 1991 Part-I and connecting to MCBDB’s earth test point all as specified or indicated including testing on complete all as specified and as directed.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials such as fitting & fixture from the site and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

Material and labour for point wiring with 1.5 Sqmm copper conductor (Multi-standard) PVC insulated and unsheathed electric cable 1100 volts in and including PVC casing and capping of 25 mm and above (as per conductor run )with all fittings/ accessories and including PVC insulated and unsheathed electric cable 1100 volts1.5 Sqmm ( multi-stranded) copper conductor single core( Green co lour) cable as continuous earth wire connected to common earth dolly including 50 mm deep box made of 2nd class hard board of required size and shape etc covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point independent controlled by one, one way switch complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 97 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 97 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 97 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing switch, socket combination 2 in 1, 5 Amp, flush type completeall as specified and as directed by Engr-in-charge.

Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin 5A/16A, 5 in 1 flush type complete all as specified and as directed by Engr-in-charge.

Supply and fixing in replacement surface mounting LED Tube light fitting incl connection from tube light fitting to ceiling rose by 23/0.0076 copper flexible wire all as specified and directed at site. Luminaire type -nxt LED 18W Retro Bar professional WH 5700K Make : Bajaj or equivalent in Philips.

S&F decorative ceiling/wall mounted "Bulkhead" luminaire with engineering plastic housing and top frame with opal PMMA diffuser as per cat part No. "CBH13/18" suitable for and incl 1X13/18W CFL of make CG or equivqlent in bajaj/philips complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint all as specified and as directed by the Engr-in-charge.

Supply and fixing MCB single pole 5 to 30 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge.

Taking out of old un serviceable under ground service connection cable of any size

Supply and fixing switch piano flush button single pole one way 5 Amps complete.

Supply and fixing angular lamp holder, PVC/Polycaronate type with back plate suitable for 9 watt LED bulb for batten fittings complete all as specified and directed by the Engineer-in-Charge.

Supplying and fixing LED 9 Watt Make: Philips/ Crompton/Havells.

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing Batten for LED tube light 1x18W LED including making suitable connection of tube light fitting to ceiling rose by 23/0.0076 copper flexible wire all as specified and directed at site by Engineer in Charge.Cat part No 112181,BLRB-DB 118. Make : Bajaj or equivalent in Philips, Havells.

S&F LED tube light 1X18Watts Cool White LED complete with ultra bright very efficacy suited for installation in Batten for LED tube light 112181 BLRB-DB 118 all as specified and directed at site by Engineer in Charge.Cat part No 112066 BLRB 18W CW. Make Bajaj or equivalent in Philips, Havells.

Supply and fixing sheet Metal enclosure single shutter type for DB’s 240 Volts Single Pole and Neutral 2 way without bus bar, complete including wooden board of required size duly painted with matching colour paint all as specified and as directed by the Engr-in-charge.

Supply and fixing 1100 volts grade heavy duty cable FR PVC unsheathed conductor served with inner sheathing of FR PVC tape and overall PVC sheathed in service connection suspended by insulated hangers not more than 1 metre apart including 4 mm suspension wire one twin core cable flat or circular 10 Sqmm all as specified and directed by Engineer-In-Charge

M&L house service breaket hook type with 3 metre long GI Pipe 40 mm dia med grade 2 Nos 90 degree bends MS hook and stay or gay complete all as specified and directed at site.

Supply and fixing MCB single pole and neutral 35to60 Amps , 240 volt, 10 KA, complete all as specified and as directed by the Engineer-in-Charge.

SHANTI ENTERPRISES

M/S LIBE & CO

M/S GEE AAR and SONS ENTERPRISES

M/S TRADE LINK

M/S GLOBAL ENGINEERS

N K BUILDERS