REPAIR MAINT TO SUNKEN FLOOR TREATMENT INTERNAL WATER SUPPLY SYSTEM SANITARY FITTINGS PAINTING AND CERTAIN B R WORKS UNDER AGE B R EAST

Amount

Treating the sunken floor slab comporising of the following specifications all as specified & directed:- (a) Demolition of cement concrete of any description in sunken portion of toilet and removing debris outside MD land. (b) Cleaning the sunken/ lowered portion of RCC slab surfaces (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely and providing 40mm thick (avg) PCC 1:2:4 type B-1 using 20mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for provision of spout (WPC measured and paid separately) (c) Rendering of uneven surfaces with 10mm thick CM 1:4 mixed with required water proofing compound as per manufacturer instruction. Fill it with water and check dampness and seepage. Where dampness/ seepage is noticed, nozzles shall be fixed and grouting carried out. (WPC shall be measured and paid separately). (d) All junctions points of side wall spout where CI/ GI pipes are passing through shall be sealed with epoxy putty. (e) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean. (f) Applying two coats of polymer modified cementious water proof coating as per manufacture instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed (This item shall be measured and paid separately) (g) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound as per manufacturers specification including rounding of corners and junctions sloping towards spout. (WPC shall be measured & paid separately). (h) Material and labour for PCC 1:5:10 type E2, using 40mm thick aggregate n exc 150mm thick as in filling of sunken floor portion complete all as specified & directed. (j) Material and labour for PCC 1:2:4 type B1 using 20mm graded aggregate, 50mm tnick as in floor etc complete all as specified & directed.

Note :- Testing of water proof area (ponding test) shall be done by filling water for at least 72 hours and tested for leakage, seepage to the entire satisfaction of GE. Test shall be done in presence of reps of Engineer-in-Charge. The treatment shall be carried out by authorised applicator of chemicals. Cost of testing is included in the unit quoted rate above.

Taking down chowkat or frame (wooden/steel/Alumnium) not exceeding 1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS Square tube complete all as specified .

S&F Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified.

Taking down shutters of any description exc 1.0 Sq.m and n.exc 2.0 Sq.m each complete all as specified and directed.

Taking down shutters of any description n.exc 1.0 Sq.m each complete all as specified and directed.

S&F 2nd class hard wood 35mm thick Factory made plain framed panelled shutter any number of panels with lock rail and panel of 9mm BWP commercial ply or 12mm veneered partical board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated etc complete all as specified and directed. .

S&F Factory made 35mm thick Glazed and skeleton door shutters/windows, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); all as specified and directed.

S&F Factory made 30mm thick Glazed and skeleton shutters/windows, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); all as specified and directed.

Preparation of new wood or wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, and fixed complete all as specified and as directed.

S&F Butt hinges 75 mm long medium weight cold rolled stainless steel complete all as specified and as directed.

Supply and fixing 150 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing aluminium handles cast type anodized 150 mm long complete all as specified and as directed.

Supply and fixing 100 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing aluminium handles cast type anodized 100 mm long complete all as specified and as directed.

S&F in repair Chromium plated soap dish including fixing arrangement complete all as specified and directed .

S&F in repair 250mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudud sections or cast- aluminium alloy and fixed complete all as specified and as directed.

S&F in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

S&F 5mm thick rubber beading strips for entrance doors having width exc 3cm but not exc 5cm to arrest entry of insects including taking down existing one complete all as specified and as directed

S&F Floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete including taking down existing one all as specified and as directed.

M&L 2nd class Gard wood Plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads in section area 6 sq.cm but not exc 13 sq cm including taking down exisiting one complete all as specified and as directed.

S&F 4 mm thick sheet glass ordinary quality and glazing complete in square n exc 0.50 Sqm in each pane complete all as specified and directed.

Taking down chowkat or frame (wooden/steel/aluminium) not exceeding 1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

S&F Steel windows with side hung shutters including projecting type hinges, frame with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F in repair of Collapsible steel gates, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and as directed'

S&F in repairs 250 mm long, ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and fixing in repairs aluminium handles cast type anodised 200 mm long complete all as specified and as directed.

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, fixed in repair to wooden frame/welded to metal frame complete all as specified and as directed.

S&F in repair aluminium body door closer hydraulically regulated,designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete as directed by Engr-in-charge.

Demolition of brick work built in cement motor including all quoin, arches, pillars etc. Complete all as specified and directed.

M & L for pre cast cement concrete block masonry type C1, 1:3:6 using (20 mm graded agrregate) solid blocks exc 10cm in width having minimum compressive strength of 50 kg/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:4 complete all as specified

M/L for Rendering, 15 mm thick cement plaster 1:4 on brick work/concrete surface finished evenand smooth with out using extra cement and all as specified and directed

Preparation of new plastered surfaces and applying two coats of cement base paint and all as specified and directed

M&L for Joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size exc 0.09 Sqm but n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed or bedding layer in cement mortar (1:4) for laying floor finish etc including Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises etc complete all as specified & directed.

Material and labour for Glazed ceramic coloured tiles 450 x 300 mm x 7/8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as skirting/ dado including 10mm thick backing coat in CM 1:4 including dismantling floor, floor hearth or wall tiling including cement mortar (backing), and rubbish off the premises complete all as specified and directed.

Complete removal of existing water proofing treatment of any description and in any position including PCC padding any thickness and cleaning with, wire brushing, watering & removal of debris outside MOD. NOTE :- Unit rate quoted shall also include for removal of PVC water storage tank wherever existing carefully and refixing at the same or other position after completion of roof repair work

M&L Cutting out cracks to V-section in existing roofs or terrace, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) etc complete all as specified and directed..

Roughening surfaces of old concrete floors by picking, sweeping, clean and washing down with water to remove dust etc. complete all as specified and directed.

M&L for Brushing neat cement slurry with 3kg/Sqm all as specified and directed.

M&L PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in concrete padding laid to required slope incl finishing the concrete surface fair and even without using extra cement complete all as specified and as directed.

M & L for 10 mm thick screed bed or bedding layer of mortar in cement mortar (1:4) for laying roof finish as padding finished using lequid WPC as per manufacturer instruction, complete all as specified and directed NOTE :- WPC shall be measured and paid separately.

M & L for applying oil bound bitumen primer @ 0.40 Litre / Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg / Litre at 25 degree Celsius on the prepared dry surface of roof etc complete all as specified & directed.

M&L for APP polymeric membrane min weight 3.0kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm laid on primed surfaces by torch application method complete all as specified and directed

M&L for preparation of new surfaces of any description not otherwise described over 10cm width or girth and applying two coats of solar reflective aluminium paint @ 0.10 kg/sqm of membrane surfaces complete all as specified and directed

Supply only water proofing Liquid water proofing compond of approved make complete all as specified and directed

Supply and fixing in replacement of galvanised GI tubing medium grade of 15 mm dia in trenches/wall/ floor/ceiling and connection in old or new position including taking down and also including fitting like socket / union / Tee / Reducer Nipple etc complete all as specified and directed.

Supply and fixing galvanised GI Tubing medium grade of 20 mm dia in trenches/wall/floor/ceiling and connection in old or new position including taking down and also including fitting like socket / union / Tee / Reducer Nipple etc complete including taking down of existing unserviceable pipeline all as directed. Note: Excavation & earthwork shall be measured & paid seperately

Petty repair for internal/external water GI/CPVC pipe line of any size coming from over head tank to the quarter including socket,elbow,nipple ,with repair to water blockage , pipe line leakage, cleaning internally , removing of air/dust blockage including concealed water tubing etc n exc 3m length of any height using scaffolding and making the water supply functional complete all as specified and directed.

Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in including taking out steel/plastic/cpvc water tubing and connections complete all as specified and directed. .

Supplying and fixing in repairs of 20mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA CPVC complete all as specified.

Supplying and fixing in repairs 20mm outer dia CPVC brass elbow etc complete all as specified and directed.

S&F Rotational moulded polythene water storage tank of 500 Ltrs capacity (three layer white colour) cylinderical vertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down of old unserviceable tank complete all as specified and directed.

S & F in repairs Bib taps fancy type chromium plated with crutch or butterfly handle screwed down screwed for galvanised iron pipe or for brass ferrule and fixed complete for 15 mm bore all as specified and as directed.

S&F in repairs of Push tap any colour high pressure of PTMT screwed for iron pipe and fixed, (Minimum weight 15mm-47gms) complete all as specified and directed.

S&F in repairs of pillar tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-110 gms) complete all as specified and directed.

S&F in repairs 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, screwed for iron pipe etc complete all as specified and directed.

S&F in repair Brass Chromium plated wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed .

S&F in repair 32 mm Waste Coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S & F in repair PVC waste pipe 32 to 40 mm dia and length n exc 2m for WHB/Sink/ Urinal up to floor trap and fixed complete all as specified

S&F PVC connections 15mm size with PTMT nuts of length 600 mm including taking down existing one complete all as specified and directed by Engineer- In - charge.

S&F in repairs 40mm bore unplasticised PVC pipe of pressure rating 10 kgf/Sqcm fixed complete to walls, ceiling or laid in floors complete all as specified and directed.

S&F Vitreous china squatting pan 'Orissa' Pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe ) including provision of cement concrete bedding fixed in repairs all as specified and as directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including taking down existing one complete all as specified and as directed.

S&F Angular stop cock, valves high pressure screwed both ends iron pipe or for unioins 15mm dia, including taking existing one complete as directed by Engr-in-charge.

S&F in repair wash basin vitreous china (flat back and angle back type) size 580x400mm including pillar taps waste chain and plug and porceline stopper but brackets including cutting for and pinning in ends of brackets or erecting stand with waste pipe fixed ,etc complete all as specified and directed.

S&F Vitreous china wash down water closet pan (pedestal pattern), white (exluding fixing bolts,flushing cistren and flushpipe) and including seat cover for pedestal pattern complete fixed in repair, all as specified and as directed.

S & F in repairs PVC low level flushing cistern 10 Ltr capacity including necessary brackets incl connecting flush pipe etc and making good the disturbed surfaces all as directed

S&F in repairs Stop Valve standard PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms) and directed.

S&F in repairs Overhead Shower rose ø125mm (Brass Chrome Plated) complete all as specified and as directed.

S & F in repair Toilet paper holder box type of vitreous china fixed to walls with chromium plated (CP) brass screws etc complete all as specified and directed.

Supply and fixing in repairs plastic water closet seat cover white or tinted, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinge device and including taking existing one complete as directed.

Petty repairs to refixing the existing Wash hand basin and Sinks made of stainless steel 1mm thick kitchen flat back including fixing cantilever CI/Angle iron brackets embedded in concrete block including connecting waste coupling 32mm bore, including bedding, waste fitting, waste pipe in cement mortar on to dwarf wall and connecting union to pipe, filling gap in white cement and all neccessary fittings to fixed in repair (including taking and refixing the same position) complete all as directed.

M&L for Preparation of old decorated plastered or unplastered surface of wall, brooming down or with steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat of oil bound distemper complete all as specified and as directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat of cement based paint complete all as specified and as directed.

S & F Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws and including dismantling of any type of sheets in roof coverings complete all as specified & directed.

M&L Rolled sections/ tubes as in main and cross beams,columns, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410W (Gde E-250) quality B including dismantling old unserviceable structure work complete all as specified and as directed .

M&L Plain cement concrete (1:3:6) type C1 using (20 mm graded stone aggregate), 75mm thick, as in plinth protection courses, top surface of concrete finished even and smooth with out using extra cement, including expansion joint 10mm thick filled with mastic filling comprising of 01 part of heated blown bitumen and 3 parts of sand including demolition of existing cement concrete including disposal of demolition material upto MD land complete all as specified and directed.

Taking down existing manually operated steel rolling shuttesr area n.exc 10 Sqm Each and erecting in same position, including easening, applying of greasing in rolling shutters channel all as specified and directed by EIC.

Supply & fixing in repairs of steel rolling shutter springs suitable for manually operated steel rolling shutters complete all as specified and directed by EIC.

Supply & fixing in repairs 50mm dia MS pipe shaft for steel rolling shutters suitably drilled and fixed in position for rolling shutters complete all as specified and directed by EIC.

M&L in repairs 300x300x25mm thick pre polished cement concrete chequered tiles jointed in neat cement slurry and pointed in white or coloured cement to match the floor and including 20mm thick screed bed in CM 1;6 etc complete all as specified and directed.

M&L PCC (1:4:8) type D2 using 40mm graded aggregate 75mm thick as in sub base of floor finished even and rough to receive top layer including demolition of Concrete (un reinforced) of any description and in any position not otherwise specifically provided etc and rubbish off the premises complete all as specified and directed..

M&L for for 18/19mm thick Prelaminated particle board, interior Grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work including taking down complete all as specified and as directed.

S&F 40 mm dia cupboard knobs fixed with nut, screw and washer of brass polished complete including taking down existing one all as specified and as directed.

S&F Continuous (piano) hinges, stainless steel bright finish or electrogalvanised of 40mm width of flaps (when open) including taking down etc complete all as specified and directed.

S&F Magnetic ball catcher with 8mm dia steel ball and brass body and striking plate including taking down in complete all as specified and directed.

S & F in repair 12 mm thick ,7 ply, plywood ,grade BWR ,type BB fixed to wooden frame work in wall with nails all as specified & directed.

S&F in repair Stainless steel spring hinges of size of approved pattern and make suitable for base/wall unit of cupboard complete (Make : BIR SS /Sleek/Blum/Hettich)

S&F in repair Stainless steel handles of size 100 mm of approved pattern and make suitable for Base/Wall unit of modular kitchen complete all as specified and directed. (Make : Spykar /Sleek/Blum/Hettich)

S&F Decorative laminates of 0.90 mm thick type matt finish, colour and pattern as approved. complete all as specified and as directed by Engneer-in-Charge

S&F in repair sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm fixed in repairs all as specified and directed. Make : M/s Diamond / Nirali / Amco / TATA

S&F Plate rack of size 65 cm x 96 cm made of stainless steel fixed in repairs complete all as specified & directed.

Taking down cement plaster on brick or stone walls, or concrete or ceilings etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises and leaving the work clear of any plastering and material and labour for Rendering 15 mm thick in two layers on brick or stone or concrete surfaces,first coat 10mm thick in cement mortar 1:4 and 2nd coat 5mm thick in cement mortar 1:4 mixed with water proofing compound as per manufacturer instructions finished even and smooth without using extra cement complete all as specified and directed. (a) Water proofing compound shall be measured and paid seperately.

Taking down cement plaster on brick or stone walls, or concrete etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises and leaving the work clear of any plastering and material and labour for Rendering 15 mm thick in CM 1:6 on brick or stone or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for Three coats of white wash on new surfaces of walls including preparation of surfaces complete all as specified.

Material and labour for Preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of primer with alkali resistant priming paint and JK Birla wall care putty all as specified and directed.

M&L applying two coats of cement based paint over and including one coat of primer, including preparation of newly plastered wall surfaces of any description, complete all as specified and as directed.

M&L for in repairs Providing precast cement concrete louvres and jallies, 50 mm thick (measured solid) set in CM 1:4, type B0 1:2:4, using 12.5 mm graded crushed stone aggregate faces are finished smooth including demolition of old mouldings all as specified and as directed.

M&L for Vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 15 mm thick screed bed or bedding layer in Cement Mortar 1:6 complete including dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises etc complete all as specified & directed.

M&L for Vitrified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertcal surfaces such as skirting/ dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 10 mm thick in Cement Mortar 1:6 as in backing coat including dismantling floor, floor hearth or wall tiling including cement mortar (backing), removing serviceable tiles to store and rubbish off the premises and complete all as specified and directed.

Grinding of existing mozaic/kota stone/tiles in wall/flooring including mirror polishing, cleaning of tiles/granite and joints filling and apply white cement, including grouting of floor trap surroundings with white cement complete all as specified and directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, chajja,ceiling, balcony, facia etc., brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent, trading, oil, greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for Preparation of old decorated surfaces of walls by using pressure washer, remove all dirt & dust ,applying one coat of wall care putty and applying two coats of premium oil bound distemper over one coat of primer as per manufauture instruction of required shade complete all as specified and directed by Engineer - in - Charge. Note:-(i) Cost of scaffolding required deemed to be included in the quoted rate of item and nothing extra shall be admissible on this account.

Dismantling battens for tiles, shingles etc of any size including tilting fillets spaced exc 15 cm complete all as specified and directed.

Material and labour second class hardwood clean sawn battens at 30cm centres sectional area exc 15 & n exc 25 Sqcm including scafoldings of any hieght complete all as specified and directed.

Except Material second class hardwood clean sawn battens at 30cm centres sectional area exc 15 & n exc 25 Sqcm including scafoldings of any hieght complete all as specified and directed.

Taking down rough dressed stone laid in plinth protection/drain walls and removing mortar from and cleaning stones; stacking for measurement including all extra handling and removal and disposing off rubbish complete all as specified and directed.

Material and labour racking out joints / pointing to squared rubble masonry, coursed or uncoursed built in cement or cement lime mortar all as specified and directed.

Material and labour for keyed pointing in CM 1:4 for squared rubble masonry all as specified and directed.

M&L for Repair of leakage/seepage from the Nahani trap/ floor trap of kitchen/ bathroom/ wash basin of the upper Qtr, in any position at any height, complete including change of floor trap, PVC horinzontal pipe of required length embeded in floor in bathroom or kitchen making good to the damage portion of flooring, laying and matching of tiles in the existing flooring, complete all as specified and directed by Engineer-in-Charge

M&L for Repair of leakage/seepage from the wall/ door bend /door tee/ 'Y' junction/ 'T' Junction of soil pipe / waste pipe/ vent pipe of kitchen/ bathroom/WC of the upper Qtr or at the ground floor Qtr including change of any damage soil waste pipes or fittings of any shape, specification and size, making good to the damaged portion of wall with brick work in cement mortar 1:6 or cement concrete 1:2:4 and plastering to wall in CM 1:4 and finished the surfaces matching to existing wall complete to avoid the leakage/ seepage at the site of work as directed and as specified. Note for item No 113 & 114 :- (a) Find out main cause of leakage and take necessary steps to resolve / rectify. (b) Replace existing tiles in case leakage through NT/FT. (c) The rate deemed to be included for provision of new NT/FT. (d) The unit rate is also deemed to be included for reqd bonding chemicals to arrest the leakage/seepage as directed by the manufacturer's specification. Make : M/s Sika Chemical, M/s Pidilite, M/s Dr Fixit

S&F Rotational moulded polythene water storage tank of 1000 Ltrs capacity (three layer white colour) cylinderical vertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down of old unserviceable tank complete all as specified and directed.

Supply and fix PVC water tank 2000 Ltrs Capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, including connecting the float valve of required size, PVC tank cover incl all fittings, 20mm bore GI medium grade overflow pipe and connect to inlet and included fittings outlet pipes, tank nipple, elbow, bend, union, sockets, etc complete all as specified and incl disconnecting and taking down existing tank of any description all as specified and directed.

S&F in repairs of Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms) and directed by Engineer in Charge.

S&F in repairs of Swivel Shower with arm of PTMT any colour and 195mm long bend of 45 degree with flange for fixed with 15mm pipe (Minimum weight 15mm-90gms)etc complete all as specified and directed.

S&F 150 mm dia round/square grating of CP with or without hole including Jointed to PVC pipe complete all as specified and directed.

Supply and fixing in repairs gun metal gate valve ISI marked with iron wheel head, screwed both ends for iron pipe of size 15 mm bore including taking down the unserviceable existing ones complete all as specified and directed.

Supply and fixing in repairs 20mm dia gun metal gate valve with iron wheel screwed both ends for iron pipe and all as specified and directed.

Supply and fixing in repairs gun metal gate valve ISI marked with iron wheel head, screwed both ends for iron pipe of size 25 mm bore etc complete all as specified and directed.

Supply and fix in repair ball valve 15mm bore high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight -210 gms) complete all as specified and directed.

Supply and fixing 25 mm dia Unplasticised PVC Pipes of pressure rating 10kgf/cm2 fixed complete to wall,ceilings or in floors etc,any type of pipe all as specified and directed.

Supply and fixing 20 mm dia Unplasticiced PVC Pipes of pressure rating of pressure rating 10kgf/cm2 fixed complete to wall,ceilings or in floors etc,any type of pipe all as specified and directed.

Material and labour for False ceiling using GI snap grid size 60x60cm with main runner 38x24,wall angle & cross tee 29x24mm wall angle 24x24mm suspended with 4mm dia GI Wire fixed with steel dash fasteners carrying max load up to 8.1 Kg/Sqcm with 4mm thick designer ceiling board (Lake & Hill) all as per Everest regular T-2430 or equivalent (Make-Ramco/Charminar/Armstrong) including dismantling of existing one all as specified and as directed.

S&F in repairs of chromium plated tubular towel rail 20 mm dia brass D type 60 cm long between flanges complete all as specified and as directed.

S&F Glass self assembly including taking down existing one complete all as directed by Engr-in-charge and all as specified and as directed.

Taking down high or low level flushing cistren 10 ltrs capacity & connections to pipes & fixing of chain & pull or lever after cleaning inside of all dirt, scale formation, replacement of rubber washers, stopping of leakage etc and refixing in same location complete all as specified and as directed

Petty repair to aluminium/glass doors, windows, ventilators, partitions and making good the same of size upto 2 Sqm (i.e. includeing making functional Handles, hinges, star lock, rubber beadings, bottom bearing, clips etc) included taking down and refixing complete all as specified and directed.

Petty repair to wooden door,skelton door, PVC door, wooden window, wooden ventilator, cupboard door, wardrobe door with shutter (size upto 2 Sqm) including making functional roller, windows, etc with minor repair and easing and adjustment/alignment to openable with assessories if required any ( like roller of cupboard door, butt hinge, handle, tower bolt, beading, bow handle, etc complete) included taking down and refixing complete all as directed.

S&F in repair powder coated aluminium curtain rod fancy type (colour as approved) of 25mm dia including brackets, stops, rollers, etc. and fixed to wall with steel screws complete all as specified and as directed .

Supply and fixing for 8 feet 4 pipes pulley operated cloths drying system consisting of aluminium pipe of outer dia 22mm, inner dia 19.80mm, made up of detrin with rope guide mounted on channel pair of length 24 feet (distance between two pipes is adjustable) locking system to hide rope knot, channel to be mounted or fixed with self taping screws provided in kit. Rope will be HDPE double core of 4mm dia fixing to ceiling as specified and directed by Engr-in-Charge and minimum weight of one pipe shall not be less than 0.20kg/, minimum weight of rope shall not be less than 7700Gms/unit .

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (108mm x 48mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. The rate includes Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.The rate exclude the glass panes.The rate include the grill and removal of old windows if any and making good all as directed by GE.

Supply and fix 4mm thick figured/filmed glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane and all as specified and directed.

M&L for hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and supply & fix for 4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass not exc 0.5 sqm in each pane complete all as specified and directed.

Supply and fixing in repair aluminium anodized hasp and staples safety type with mild steel hinge pin incl bolt to hinge plate fixed with screws of 100mm length complete all as specified and as directed.

M&L for Preparation of old painted wooden surface of any description and applying one coat of synthetic enamel paint using mechanical means, not otherwise described over 10 cm width or girth, complete all as specified and directed.

M&L for Preparation of old painted surfaces of steel and applying one coat of synthetic enamel paint using mechanical means over 10 cm width or girth, not other wise described complete all as specified and as directed.

Material and labour for removing plant/Uprooting of vegetation growth including roots on wall/roof/parapet near pipes etc and applying acid treatment after removing roots for preventing regrowth and making good disturbed surfaces/area in superficial area exc 150sq.cm but n.exc 400 sq.cm and averaging depth not exceeding 10 cm by using PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) or 10mm thick plastering in cement mortar 1:3 as required and finishing the surfaces to match with the existing surface complete all as specified and directed. Note :- (a) Rate quoted by the tenderer shall be deemed to inclusive of double steel scaffolding. (b) Contractor shall provided safety gears to his workers at his own cost and safety pre caution to avoid accidents.

Material and labour for dismantling the existing unserviceable gully trap including chamber and material and labour for provision of salt glazed stoneware gully tarp, square or round mouth type "P" of size 180X150mm, including setting and jointing in cement mortar 1:1 plain cement concrete base in PCC 1:2:4 type B1, brick work in cement mortar 1:4 rendering in cement mortar 1:4 all around finished even and fair using extra cement RCC cover slab in RCC type B1, 1:2:4 with 6mm dia reinforcement etc, complete all as specified and directed

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls bore of pipe 75 mm with PVC clamps and saddles including taking down existing pipes including dismantling of cast iron/RCC/PVC drain pipes jointed in cement mortar and taking out from trenches or walls of any bore including fittings complete all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls bore of pipe 110 mm with PVC clamps and saddles including taking down existing pipes including dismantling of cast iron/RCC/PVC drain pipes jointed in cement mortar and taking out from trenches or walls of any bore including fittings complete all as specified and directed.

S & F PVC (SWR) bends of any radius with access door bore of pipe 75 mm complete all as specified and directed.

S & F PVC (SWR) bends of any radius with access door bore of pipe 110 mm complete all as specified and directed.

S & F PVC (SWR) junction single (single T) equal or unequal with access door bore of pipe 75 mm complete all as specified and directed.

S & F PVC (SWR) junction single (single T) equal or unequal with access door bore of pipe 110 mm complete all as specified and directed.

S & F 125/ 110 mm bore PVC (SWR) floor trap plain with grating incl jointing with solvent cement complete all as specified and directed. Note :- An amount of Rs 25318.00 on account of credit schedule for schedule 'A' part II shall be deducted from the total amount of BOQ to arrive at the contract sum.

SREE BUILDERS

BYRAVESHWARA CONSTUCTION

SRI LAKSHMI VENKATESHWARA ENTERPRISES

chowdeshwariconstructionco