Construction of Balance work of High Mount VVIP Rest House Building and Surrounding premises at C.S. No. 224 Malabar Hill, Mumbai (Including Electrical Work)

Amount

Item No:1 Removing any kind of debris including loading in truck & conveying to dumbing point approved by MCGM unloading, spreadingetc complete without lead 50km and lifts. (Removing the existing debris littering around site without causing dust nuisance and disposing off and cleaning the site etc. complete. )

Item No:2 Lowering down the debris to the ground floor obtained from breaking and removing the cement plaster/burnt brick masonry of the first floor by any means without causing dust nuisance and damage to structure, stacking the same as and where directed including cleaning the site complete.(Cleaning existing floors of unwanted debris / material and disposing them off etc. complete).

Item No:3 Dismantling brick masonry in lime or cement mortar and stacking the materials as directed with all leads, lifts etc

Item No:4 Removing brick bat coba including stacking the spoils as directed with all leads, lifts etc, complete.

Item No:5 Removing lime or lean cement concrete including stacking the spoils as directed with all leads, lifts etc, complete

Item No:6 Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete.

Item No:7 Providing pre constructional anti termite treatment as per I.S. 6313(Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bondpaper.

Item No:8 Providing preconstructionaantitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper.

Item No:9 Providing antitermite treatment to the wooden frames of doors/ windows of the existing building as per I.S. 6313 (Part-III) by drilling 6mm dia. holes at four corners on one side and four corners on other side at a downward angle of about 45 degree at the junction of wood work and masonary and injecting 150 ml. of chlorodane 5% W.C. and sealing by filling putty etc. complete covering 2 years guarantee on bond paper.

Item No:10 Providing cement based water proofing treatment to terraces(Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface.Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C. M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete.

Item No:11 Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 kg. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge) (Including all floors with all lead & lifts.)

Item No:12 Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on virgin concrete slab with waterproofing compound @ 1kg/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 kg/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 kg/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete.

Item No:13 Providing internal cement plaster 12mm thick in single coat in cement mortar 1:3 without neeru finish to concrete or brick surfaces, in all position including scaffolding and curing etc.complete.

Item No:14 Providing and applying gypsum plaster ( with Gypsum material of Gypsum India / Mega Sign or equivalent make ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete.

Item No:15 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 milimetre thick in cement mortar 1:4 using waterproofing compound at 1 killogrammes per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 milimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No:16 Labour charges for providing groove in external plaster having width and spaced as directed by engineer incharge etc. complete.

Item No:17 Providing and laying machine cut machine Polished Kota stone flooring 25mm to 30mm thick and required width in plain/ diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. For Flooring.

Item No:18 Providing and laying machine cut machine Polished Kota stone flooring 25mm to 30mm thick and required width in plain/ diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. For Skirting.

Item No:19 Providing Mirror polishing to Kota Stone including using all necessary stones and equipments cleaning, washing etc. complete.For Flooring

Item No:20 Providing Mirror polishing to Kota Stone including using all necessary stones and equipments cleaning, washing etc. complete.For Skirting

Item No:21 Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. a) Flooring

Item No:22 Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm to 8 to 10mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete. b) Skirting

Item No:23 Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm or 60 cm x 60 cm and confirming to corresponding IS for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.

Item No:24 Providing and laying ceramic tiles having size 30 cm x 45 cm or 60 cm x 120 cm confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Item No:25 Providing and laying machine cut, Italian Marble stone flooring laid in approved pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Item No:26 Providing and laying in position skirting of Italian Marble of approved shade with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Item No:27 Providing and laying in position Treads & Risers Italian Marble of approved shade with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Item No:28 Providing and laying in position dado of Italian Marble of approved shade with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Item No:29 Providing and laying Italian Marble of 18 to 20 mm thick for door frame / window boxing / Sills etc. as per detailed drawing and design on C.M. 1:4 including filling joints with polymer base filler nosing / chamfering the edges, Moulding / rounding, edge polish wherever necessary, curing,chemical compound etc. complete. Spec. As directed by Engineer in charge.

Item No:30 Providing Mirror polishing to Italian marble including using all necessary stones and equipments cleaning, washing .Floor Scrubbing marble stone with Single Disc Mirror Polishing using scrubbing pads then using floor polishing to remove dust & dirt & apply polish powder & single disc machine to make it shine and increase the gloss etc.complete.Spec. As directed by Engineer in charge Flooring, Skiriting,Frames,treads and Risers,Frames.

Item No:31 Providing and laying cement concrete flooring 40mm thick with M20 cement concrete laid to proper level and slope in alternate bays, including compaction, filling joints, marking lines to give appearance of tiles of 30cm x 30cm or other size laid diagonally/square etc. finishing smooth (with extra cement) in any colour as directed and Curing etc. complete. With Crushed Sand. Spec. No. Bd.M.6. (Slab for laying wooden flooring)

Item No:32 Providing and laying in position Three layes parquet / Engineered Wooden flooring having plank size of 135mm to 210mm wide, 1800 to 2420mm long of 15mm thick with approved veneer on top including all necessary jointing and core material as per detailed drawings & design etc. complete. Spec. As directed by Engineer in charge .

Item No:33 Providing and laying in position flooring of telephone black / Amba White / Catbary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 milimetre to 20 milimetre thick on bed 1:6cement mortar including cement floats striking joints, painting in Cement Mortar. 1:3 curing and cleaning etc. complete.

Item No:34 Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red /Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortarincluding float filling joints with neat cement slurry curing polishing and cleaning etccomplete.

Item No:35 Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete.(Suits)

Item No:36 Providing and fixing false ceiling with eco-friendly light-weight calcium silicate tiles of spintone surface texture aerolite make or equivalent of size 595mm x 595mm having 15mm thick densified micro look edge and 100% humidity resistance incombustible as per BS 46part IV and thermal conductivity 0.043 w/m 0 KC and NRC 0.50 placed in true horizontal level suspended grid of size 600x600mm made from hot dipped G.I. steel sections ion silhouette profile,rotary stitched double webbed white with 6mm reveal profile (white/black), wherein, main T runner of size 42mmx14mm between main tee 600mm center-tocenter and secondary cross T of size 33x14x0.43mm thick of length 600mm long spaced inter-locked at middle of the first crossed T in each panel to form grid of 1200mmx600mm resting on periphery wall Profile wall section 19mm (7+7) x19mmx0.40thicknesses and laying false ceiling for services like diffusers grills including cutting, making opening for light fittings, fixtures,smoke detectors etc., wherever required.Main T runners suspended from ceiling with using G.I. soffit cleats of size 25x35x1.6 mm of required length fixed to the ceiling with 6mm dia and 50mm long dash fastener, 4mm dia G.I. adjustable 50mm long dash fasteners, 4mm G.I. adjustable rods withpowder coated/good quality G.I. level adjustment clips of 35x35x0.8mm spaced @1200, center-to center along main T all complete at all heights as per the specifications, drawings. (Restaurant and Coffee House)

Item No:37 Providing and fixing false ceiling of 15mm thickas per drawings including powder coated G.I. wall angle of 20 mm x 20 mm x 0.60 mm size, G.I. grid runners of size 15 mm x 38 mm at 600 mm center to center both ways and suspended using G.I. 3 mm wire including fixing using butterfly clips and fasteners including transporting, scaffolding all necessary labour and machinery, finishing etc. complete.(Corridor) (Armstrong ceiling made up of Mineral fiber ceiling )

Item No:38 Providing and fixing Modular false ceiling of 600 x 600 mm center to center and 13 mm thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended false ceiling consisting of alluminium T 2”x1 ½” (50 mm x 40 mm) weighing 0.39 kg/m at 60 cms center center and fixed with ½” x ½” (15 x 15 mm) flanges weighing 0.19 kg/m suspended on 6 mm dia mild steel rod weighing 0.22 kg/m, fixed on wall and beams including rounding of the edges with alluinium T of 2” x 1 ½” (50 mm x 40 mm) weighing 0.39 kg/m etc. (all alluminium sections shall be anodized) including all labour, material, lifts etc. complete. (Toilets)

Item No:39 Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron hold fast of size with oil painting, etc. complete.

Item No:40 Providing & fixing solid core flush door in single / double leaf 50mm thick decorative type of exterior grade as per detailed drawing & design including approved veneer on both face, fittings, Brass oxidised fixtures of approved make and size as specified in the drawing including all necessary beads, moulding, lipping, melamine polish etc. complete. (without door frame). Spec. As directed by Engineer in charge.

Item No:41 2 Hour Insulated, Flame, Smoke Radiation check Lead Lined Fire Door 57mm 2HR FRL(120/120) 3 Criteria - INTEGRITY / INSULATION/ STABILITY WOODEN DOOR –FireDoor Tested in accordance to IS: 3614 Part 2. with prior approval of concerned SuperitendingEngineer.Providing of 120 min Fire rated lead lined doors system duly tested for 3 criteria - Integrity, Insulation and Stability Criteria as per the IS: 3614 Part 2 and BS: 476 part 22 with standardheating conditions as specified in IS:3614 Part II 1992 and BS: 476 part 20 & 22 1987 to achieve the required integrity, insulation and stability (i.e. to restrict the heat radiation,temperature rise on the non fire side to the maximum of 140° C above the ambienttemperature on the exposed surface of the shutter. The fire doors are tested with NCBNtechnology ("Non Combustible by Nature"). Lead lined to check radiation. Code No; 2 HourInsulated, Flame, Smoke Radiation check Lead Lined Fire Door 57mm 2HR FRL (120/120) 3 Criteria - INTEGRITY / INSULATION/ STABILITY WOODEN DOOR - Fire Door Testedin accordance to IS: 3614 Part 2

Item No:41(A) a) Door Frame: Providing Frames for Lead Lined Fire resistant door shutters 1st class Malaysian Hardwood Frame densified and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160 PSI pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 140 X 70 mm with 45mm thick two layered 3mm Lead Line Sheets with 10mm overlap from either side & spray quoted with 2 coats of In tumescent paint of minimum 200 micron, with 1 row of Brush- Type Astroflame® intumescent strip (imported) of size 10mmx4mm concealed in the groove of the Frame for fire and hot and cold smoke sealing, etc. complete as per direction of Engineer in Charge.

Item No:41(B) b) Shutter: Providing of 57mm thick asbestos free composite, 'TUFWUD' brand - 3 criteria - fire, heat and smoke check Lead Lined Door Shutter with flame guard of 120 minutes IS3614 part -II comprising of 2x9mm Calcium Silicate boards, Chemical treated internal timber with Fire retardant chemicals in pressure impregnation vessels under 160 PSI pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 frame work of 100x30 mm with 30mm thick infill of ceramic fibre (density 128 Kgs/CMT) vermiculite mix, 3mm thick Lead Sheet on one side faced & 3mm Fire retardant High Density Fibreboard, internally lipped with hardwood beading, and pasted in Hydraulic Press under 50 tonnes pressure, spray quoted with 2 coats of Intumescent paint of minimum 300 micron, and with 1 row of Brush- Type Astroflame® intumescent strip (imported) of size 10mmx4mm concealed for fire and smoke sealing in the grooves in the shutter on all edges except bottom, without any external lipping.

Item No:42 Providing and applying melamine polish of required finish to the wood work by spray machine including knotting and preparing the even surface byscrapng, applying Frenchpolish , scaffolding if required etc. complete. Note:The work to be executed on prior approval of Superintending Engineer will be necessary.

Item No:43 Providing &fixing Hardware of approved brand and make to doors as directed on drawings, etc. complete. Spec. : As directed by Engineer in charge. Pull Handle (Neki PHA 2210 Satin/Godrej LNEH 16-200mm/LAPO polo main door handle/Godrej Gloria satin door handle) (Including all floors with all lead & lifts.)

Item No:44 Providing & fixing Hardware of brass /SS approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. Door Closure-Concealed (Dorset Make/Overhead Dorma TS 90/Yale slim concealed door with necessary components) .

Item No:45 Providing & fixing Hardware of brass/SS approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. Door Floor Spring (HYPER make/Yale make/Volo make/Godrej make with necessary components) .

Item No:46 Providing &fixing Hardware of approved brand and make to doors as directed on drawings, etc. complete. Spec. : As directed by Engineer in charge. Floor door stopper (Neki DST 1005/Volo/Godrej with necessary components)

Item No:47 Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. Sign Plates (200x300mm)(SS Body) (Neki EP42 with necessary components) (Including all floors with all lead & lifts.)

Item No:48 Providing & fixing Hardware of brass/SS approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. Cylindrical Lock (Godrej cylindical SS finish Premium lock/IPSA High security SS body with necessary components) (Including all floors with all lead & lifts.)

Item No:49 Providing & fixing Hardware of approved brand and make to doors as directed on drawings, including all necessary fitting etc. complete. Mortise lock with card Access(Dorset/Dorma/Yale YDM smart door lock with necessary components)

Item No:50 Providing &fixing Hardware of approved brand and make to doors as directed on drawings, etc. complete. Spec. : As directed by Engineer in charge. Mortise lock(Godrej/Yale/LAPO/Atom with lock body and necessary components)

Item No:51 Providing &fixing Hardware of approved brand and make to doors as directed on drawings, etc. complete. Spec. : As directed by Engineer in charge. Safety chain(High duty) (Harrison/Yale/IPSA or equivalent)

Item No:52 Providing &fixing Hardware of approved brand and make to doors as directed on drawings, etc. complete. Spec. : As directed by Engineer in charge. 16mm dia. & 450mm long Aldrop (CENT or equivalent)

Item No:53 Providing &fixing Hardware of approved brand and make to doors as directed on drawings, etc. complete. Spec. : As directed by Engineer in charge. 12mm dia. & 350mm long Tadipatti

Item No:54 Providing &fixing Hardware of approved brand and make to doors as directed on drawings, etc. complete. Spec. : As directed by Engineer in charge. 450mm long tower bolt

Item No:55 Providing and fixing in position Glass Shower Enclosure of Jaquar (BSD-CHR-SDR2022X) or equivalent make as per design and drawing (H=2000mm & W = 2001 to 2200mm)

Item No:56 Providing and fixing in position glass partition with glass door made up of 12mm thk clear toughened glass with approved patch plates and fittings, edge polishing inluding necessary hardware, aluminium U channel, floor spring, neoprene gasket, silicon sealent, SS handles, Patch lock, Pivot patch etc. complete as directed.

Item No:57 Providing and fixing full height glass partitions of 12mm thick clear toughened glass fixed in alluminium profile as per detailed drawing & design. Rate should be inclusive of all necessary hardware and labour required. Edges of to glass panels should be sealed with silicon sealant or glass adhesives, edges of glass should be machine polished, divisions of glass as per drawings etc. complete. Spec. As directed by Engineer in charge.

Item No:58 Providing and fixing in position UPVC sliding Windows of three tracks as per detailed drawings & design and pristine white colour ,slider of bugscreen, no monsoon guard ,no mesh joint , S65 PS1 slider sash,S65 PS1 bug sash ,fibre mesh bug mesh , BS midrail , inside BS position , normal BS midrail type , slider threshold with threshold /118 mm, 1 no. BS midrail ,C type BS handle, aperture plaster finish , white colour handle, inner & outer track espag patio handle , DG INS TGH(6T + 12 + 6T) as directed by Engineer in charge with all necessary UPVC sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jali with all required screws and nuts etc, complete. Spec. As directed by Engineer in charge.

Item No:59 Providing and fixing in position UPVC sliding windows of two tracks of fenesta make as per detailed drawings & design and pristine white colour ,slider of bugscreen, no monsoon guard ,no mesh joint , S65 PS1 slider sash,S65 PS1 bug sash ,fibre mesh bug mesh , BS midrail , inside BS position , normal BS midrail type , slider threshold with threshold /118 mm, 1 no. BS midrail ,C type BS handle, aperture plaster finish , white colour handle, inner & outer track espag patio handle , DG INS TGH(6T + 12 + 6T) as directed by Engineer in charge with all necessary UPVC sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jali with all required screws and nuts etc, complete. Spec. As directed by Engineer in charge.

Item No:60 Providing and fixing in position UPVC sliding windows / ventilators of three tracks of fenesta make as per detailed drawings & design and pristine white colour ,slider of bugscreen, no monsoon guard ,no mesh joint , S65 PS1 slider sash,S65 PS1 bug sash ,fibre mesh bug mesh , BS midrail , inside BS position , normal BS midrail type , slider threshold with threshold /118 mm, 1 no. BS midrail ,C type BS handle, aperture plaster finish , white colour handle, inner & outer track espag patio handle , DG INS TGH(6T + 12 + 6T) as directed by Engineer in charge with all necessary UPVC sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jali with all required screws and nuts etc, complete. Spec. As directed by Engineer in charge.

Item No:61 Providing and fixing in position UPVC ventilators of Size 600mmX900mm with fixed glass and arrangement for exhaust fan of 150mm dia. Etc. complete

Item No:62 Providing and fixing in position with Powder Coatedaluminium openable window of any size as per detailed drawing and as directed by Engineerincharge with all necessary alluminium sections including necessary fixtures and fastening with 5 mm thick clear float glass etc. complete.

Item No:63 Providing and fixing 8mm thick circular toughened Glass railing as per detailed drawings & design including framing by SS components etc. complete.

Item No:64 Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top,40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete.

Item No:65 Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 milimetrediametre. and vertical pipe of 38 mm dia at 0.60 m centre to centre or as required and horizontal pipes of 25milimetre diametre in three rows, all pipes of 2 milimetre thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 milimetredia above newel post of 75 milimetre diameter etc. complete (Prior approval of sample and brand by Executive Engineer is necessary before use).

Item No:66 Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.

Item No:67 Providing and applying three coats pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. Spec. As directed by Engineer in charge.

Item No:68 Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases (NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide and Absorbs CO2 (4.8 kg/15 l) plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist. Spec. As directed by Engineer in charge.

Item No:69 Providing,aupplying,fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and shade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc .overall weight of the ACP shall not be less than 7.5 kg/sqm) .

Item No:70 Providing & fixing fabric based Wallpaper to walls including cleaning the surface, making it suitable to receive wallpaper as per manufacturers specifications as directed.,etc. complete.

Item No:71 Providing and Fixing 3M safety Glass film to Window area.

Item No:72 Providing and Fixing Frosted Film manufactured by 3M approved equivalent on glass partition wherever required as per instruction of architect.

Item No:73 Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Item No:74 Providing and fixing in walls /ceiling/ floor 40mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete

Item No:75 Providing and fixing in walls/ ceiling/ floor 32mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete. and as directed by Engineer in charge.

Item No:76 Providing and fixing in walls/ ceiling/ floor 25mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete. and as directed by Engineer in charge.

Item No:77 Providing and fixing in walls/ ceiling/ floor 20mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete. and as directed by Engineer in charge.

Item No:78 Providing and fixing in walls/ ceiling/ floor 15mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete including removing existing pipe line if necessary and conveying and stacking the same as directed etc. complete. and as directed by Engineer in charge.

Item No:79 Providing and fixing screw down for 50mm dia. C.P. wheeled stop tap of brass including necessary sockets/ union nut complete.

Item No:80 Providing and fixing screw down for 40mm dia.wheeled stop tap of brass including necessary sockets/union nut complete

Item No:81 Providing and fixing screw down for 25 mm dia.wheeled stop tap of brass including necessary sockets/ union nut complete.

Item No:82 Providing and fixing screw down for 20mm dia.wheeled stop tap of brass including necessary sockets/union nut complete.

Item No:83 Providing and fixing Angular stop cock with wall flange Jaquar make or equivalent continental including necessary sockets/union nut etc. complete. (Jaquar make OPP-15053PM) Spec. As directed by Engineer in charge.

Item No:84 Providing & fixing Two way BIB cock with Health faucet etc. complete. Spec. As directed by Engineer in charge. (2 way BIB cock :Jaquar make OPP15041PM, Health faucet : Jaquar make ALD-CHR-573)

Item No:85 Providing & fixing single lever wall mixer 3 in 1 system with provision for both hand shower &over head shower with 115mm long bend pipe, connecting legs & wall flange with Hand shower 140mm round shape single flow with aur effect (ABS body & face plate chrome plated) with rubit cleaning system including Flexible tube 12mm dia. & 1.5m long with nuts and Wall outlet with shower hook in square shape, Over head shower 200x 200mm sqauare shape flow (ABS body chrome plated with gray face plate) with rubit cleaning system and fittings like socket union, nuts, bends, valves, reducers, including necessary drilling holes in walls, slabs etc and remaking good the demolished portion to restore the same in original condition neatly and cleaning the site after completion of work, testing etc. complete. Spec. As directed by Engineer in charge. (Wall Mixer :Jaquar make OPP-15125PM, Shower Arm-SHA455L600,Hand shower : HSH-1731, Over head Shower : Jaquar make OHS-35497, Flex Tube : Jaquar make SHA-549D12, Shower Rail: Jaquar make SHA-1189N).

Item No:86 Providing and fixing BIB cock with wall flange of Jaquar make including necessary sockets/ union nut etc. complete. Spec. As directed by Engineer in charge. (Jaquar make OPP-15037PM)

Item No:87 Providing & fixing in position Wall hung WC with UF soft close slim seat cover, Hinges, accessories set, of size 360 x 500 x 380mm, Single piece slim concealed cistern with floor mounting frame, installation kit & S type drain pipe connection set for wall hung WC without flush control plate, etc. complete. Spec. As directed by Engineer in charge. (Wall Hung WC with seat cover :Jaquar make LYS-WHT-38951SM, Concealed cistern : Jaquar make JCS-WHT-2400FS, Flush control panel : Jaquar make JCP-CHR-852415)

Item No:88 Providing & fixing Paper holder with flap etc. complete. Spec. As directed by Engineer in charge. (Paper Holder :Jaquar make AHS-1553)

Item No:89 Providing and fixing White Glazed Earthenware full stall type Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia. P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall.

Item No:90 Providing and constructing Italian Marble platform for basin as per detailed drawing & design including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished Italian Marble 16 to 20 mm top with side strips of Italian marble at front and both sides of platform raised with two vertical Italian mable supports and top Italian marble including cutting etc. complete. Spec. As directed by Engineer in charge.

Item No:91 Providing and fixing white glazed earthenware Table top basin including single lever basin mixer (Piller cock) without pop up waste with 450mm long braided hoses, Bottle trap (with internal partition) 32mm size with 300mm & 190mm long wall connection pipes & wall flange, exposed part kit of concealed stop cock with fitting sleeve, operating lever & adjustable wall flange with seal etc. complete. Spec. As directed by Engineer in charge. (Table Top Basin :Jaquar make KUS-WHT-35935, Piller cock : Jaquar make OPP-15011BPM, Bottle Trap : Jaquar make ALD-769L300x190, Angular Stop Cock : Jaquar make OPP-15053PM).

Item No:92 Providing and fixing white glazed earthenware Counter top basin including single lever basin mixer (Piller cock) without pop up waste with 450mm long braided hoses, Bottle trap (with internal partition) 32mm size with 300mm & 190mm long wall connection pipes & wall flange, exposed part kit of concealed stop cock with fitting sleeve, operating lever & adjustable wall flange with seal etc. complete. Spec. As directed by Engineer in charge. (Counter Top Basin :Jaquar make KUS-WHT-35601, Piller cock : Jaquar make OPP-15011BPM, Bottle Trap : Jaquar make ALD-769L300x190, Angular Stop Cock : Jaquar make OPP-15053PM).

Item No:93 Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 milimetre x 450 milimetre size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 milimetre thick supports with kadappah top 35 to 40 milimetrethick and polished granite 16 to 20 milimetre top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 centimetre height and top granite of 75 x 40 centimetreincluding cutting,opening for sink of required size in kadappah as well as granite etc. complete. (Plat form top size 5.00 m x 0.60 metre and height is 0.75 m).

Item No:94 Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete. Spec. As directed by Engineer in charge.

Item No:95 Providing and fixing single lever sink mixer with swinging spout (Table mounted) with 450mm long braided hoses of Jaquar make including necessary sockets/ union nut etc. complete. Spec. As directed by Engineer in charge. (Jaquar make OPP-15173BPM)

Item No:96 Providing and fixing 10 centimetre Poly Vinyl Chloride nahani trap with grating etc. complete. Spec. No. BD.V 32 A page 551 and as directed by Engineer in charge.

Item No:97 Providing and fixing Belgium mirror on 8mm thick waterproof ply with alluminium profile on all four edges as per detailed drawings & design etc. complete. Spec.As directed by Engineer in charge.

Item No:98 Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. Spec. As directed by Engineer in charge.

Item No:99 Providing and fixing ISI 1729/2002 grade 75 mm dia Cast Iron Waste Water Pipe with lugs necessary fittings such as bends, tees, single junction, double junction, slotted vent, offsets on wall or into the ground including filling joints with cement mortar 1:2 proportion fixing on wall by means by galvanised Mild Steel bracket of 30 x 5 mm plate and 8 mm square rod with Galvanised Iron clamp with washer as per design drawing and as directed to keep pipe 50 mm away from wall including necessary scaffolding and painting the exposed faces with one coat of red lead oil paint and two coats of gray oil paint including removing the existing pipe if necessary and conveying and stacking in PWD Chowky or as directed by Engineer in-Charge.

Item No:100 Providing and fixing ISI 1729/2002 grade 100 mm dia Cast Iron Soil Pipes With lugs including plug bend necessary fittings such as bends, tees, single junction, double junction, slotted vent, offsets on wall or into the ground including filling joints with cement mortar 1:2 proportion fixing on wall by means of galvanised Mild Steel bracket of 30 x 5 mm plate and 8 mm square rod with Galvanised Iron clamp with washer as per design, drawing and as directed to keep pipe 50 mm away from wall including necessary scaffolding and painting the exposed faces with one coat of red lead oil paint and two coats of white oil paint including removing the existing pipe if necessary and conveying and stacking in PWD Chowky or as directed by Engineer-in-Charge.

Item No:101 Providing and fixing in position C.I. 110mm outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etc. complete.

Item No:102 Providing and fixing 15cmx10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink,connecting glazed stoneware pipe,brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Item No:103 Providing and laying 100mm dia salt glazed stoneware pipe including fittings such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

Item No:104 Providing and laying for 150mm dia salt glazed stoneware pipe including fittings Such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

Item No:105 Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete.

Item No:106 Providing and constructing Brick Masonry Inspection Chamber 90cm x 90cm x 45cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete.

Item No:107 Providing and fixing 45 cm wide mild steel ladder of 40mm x 6 mm mild steel flat stringers and steps of 18 mm dia. mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete. (Anti Corossive Paint)

Item No:108 Providing and fixing Single towel rail 600mm long of Jaquar make including all accessories complete. Spec.As directed by Engineer in charge. (Towel rail :Jaquar make CAN-1111SM)

Item No:109 Providing and fixing Towel ring round with round flange (Stainless steel) of Jaquar make including all accessories complete. Spec.As directed by Engineer in charge. (Towel ring :Jaquar make CAN-1121BN)

Item No:110 Providing and fixing Towel rack with lower hanger of Jaquar make including all accessories complete. Spec.As directed by Engineer in charge. (Towel rack :Jaquar make AHS-1581)

Item No:111 Providing & fixing Soap Dish holder etc. complete. (Soap dish holder :Jaquar make CAN-CHR-1131N or equivalent)

Item No:112 Providing & fixing Soap Dish holder with Glass Bottle of jaquar make and design.Item to include making holes and necessary hardware like screws etc. and making good the damages etc. complete. (Soap dispenser :Jaquar make AKP-CHR-35735P)

Item No:113 Providing & fixing Tumbler holder of Jaquar make etc. complete. (Tumbler holder :Jaquar make CAN-1141N)

Item No:114 Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete.

Item No:115 Providing and laying for 225 mm dia.salt glazed S.W.Pipe including fitting such as bends,tees,singlejunction,double junctions laying,jointing (including excavation and refilling the trenches) complete.

Item No:116 Providing and constructing Brick Masonry inspection trap Chamber 90cmx45cm including 1:4:8 C.C foundation,1:2:4C.C.channels/half round glazed stoneware pipe channel,salt glazed stone-ware intercepting trap with rodding pipes etin1:4:8cement concrete block,brick masonry plastering inside and Outside,fixed in cement concrete with R.C.C. Cover medium duty 140 kg. etccomplete.

Item No:117 Providing and laying in trenches 50mm dia. CPVC pipe including necessary excavation, fittings. Refilling trenches etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No:118 Providing and fixing 50 milimetre diameter water meter with non-returnvalve including strainer , sockets/ union nut and including water meter box making locking arrangement and lock. [without chamber ]

Item No:119 Providing and fixing screw down for 50 mmdia.wheeledstoptap of brass including necessary sockets/union nut complete.

Item No:120 Providing and fixing in position coffee table 4 seater 1200x750x750 in size of approved design by using Teak wood legs size of 75mmx75mm and Top frame work 75mmx50mm cross support at end of the Top, using 19mm thick marine plywood (I.S.710/1996)for Top and finishing the Top by using 4mm veneer. The exposed area of the teakwood and Veneer shall be finished by Melamine polish as per drawing and Design or as directed by engineer in charge.

Item No:121 Providing and fixing in position caffee table 6 seater 1830x750x750 in size of approved design by using Teak wood legs size of 75mmx75mm and Top frame work 75mmx50mm cross support at end of the Top, using 19mm thick marine plywood (I.S.710/1996)for Top and finishing the Top by using 4mm veneer. The exposed area of the teakwood and Veneer shall be finished by Melamine polish as per drawing and Design or as directed by engineer in charge .

Item No:122 Providing and Fixing in position Dining Chair of approved design with Teakwood Frame, approved quality cishions for seat and back as per drawing and design or as directed by engineer in charge.

Item No:123 Providing and Fixing in position Cash Counter table of size 4m x 0.60m x 1.37m as per design in 19mm thk marine ply with- a. 4 mm thk veneer on exposed faces with melamine polish and b. 1mm thk laminate on all inner unexposed faces, inclusive of necessary hardwares and fittings etc. complete as per drawing and design or as directed by engineeer in charge.

Item No:124 Providing & fixing Ventilo or equivalent make Mid back chairs in required position as directed by Engineer in charge etc. complete.complete.

Item No:125 Providing and Fixing in position Bar Counters of size 1400X1400X800 mm made up of 19mm thk marine palywood and 4mm veneer with necessary melamine polish as per spec. in size and drawing and design or as directed by engineer by charge.

Item No:126 Providing and Fixing in position Bar Chairs of approved make having size (H min 34.5 - max 44 x W 18 x D 21) ; Seating Height: min 24 - max 32 (all dimensions in inches) seating material of leather of approved colour, legs with revolving chrome base as drawing and design or directed by enginner in charge.

Item No:127 Providing and Fixing in Position Oval shaped Center table with glass top 12mm thick and size 900mmx700mmx400mm made out of teak wood frame of 75mmx75mm section with 12mm thick marine Ply and 4mm thk veneer on top including two coats of melamine polish for wood work and anti-termite treatment to plywood and wood work as per drawings and instructions of Engineer in charge etc complete.

Item No:128 Providing and Fixing in Position Oval shaped Coffee table of size 700mmdia - 400mm high made out of teak wood frame of 75mmx75mm section with 12mm thick marine Ply and 4mm thk veneer on top including two coats of melamine polish for wood work and anti-termite treatment to plywood and wood work as per drawings and instructions of Engineer in charge etc complete.

Item No:129 Providing & fixing Centre table (Round 55cm dia) of Godrej or Equivalent make in required position as directed by Engineer in charge., Complete.

Item No:130 Providing and Fixing in Position Single Bed 2250mmX900mm of approved design made up of 19mm thk marine plywood, 4mm thk approved veneer for exposed faces and 1mm thk approved laminate for unexposed faces, finished with melamine polish asper approved design and drawings etccomplete.

Item No:131 Providing and Fixing in Position Double Bed 2250mmX1800mm of approved design made up of 19mm thk marine plywood, 4mm thk approved veneer for exposed faces and 1mm thk approved laminate for unexposed faces, finished with melamine polish asper approved design and drawings etccomplete.

Item No:132 Providing and Making Dressing Table of size 450mmx300mmx500mm made up of 19mm thk marine pplywood, 4mm veneer on exposed faces and 1mm thk laminate on unexpsoed faces, finished with melamine polish as per approved design and drawing. The unit has two drawers. All fistures and fittings of approved make. The dressing table has a mirror of 4mm thick and size fixed on given surface.The mirror size considered is 1500x350x4(t).

Item No:133 Providing and Making Study Table 900X600X750mm of approved design made up of 19mm thk marine plywood, 4mm thk approved veneer for exposed faces and 1mm thk approved laminate for unexposed faces, finished with melamine polish asper approved design and drawings etc complete.

Item No:134 Providing and Making Wardrobe as per given design made up of 19mm thk marine pplywood, 4mm veneer on exposed faces and 1mm thk laminate on unexpsoed faces, finished with melamine polish as per approved design and drawing. All fixtures and fittings of approved make.

Item No:135 Providing and Making Side Table of size 600mmx450mmx450mm made up of 19mm thk marine pplywood, 4mm veneer on exposed faces and 1mm thk laminate on unexpsoed faces, finished with melamine polish as per approved design and drawing. The unit has two drawers. All fixtures and fittings of approved make.

Item No:136 Providing and Making Corner Table of size 450mmx450mmx450mm made up of 19mm thk marine pplywood, 4mm veneer on exposed faces and 1mm thk laminate on unexpsoed faces, finished with melamine polish as per approved design and drawing. All fixtures and fittings of approved make.

Item No:137 Providing & fixing Ply paneling of 12mm thick marine ply on 50x25x2mm thkaluminium pipe framework at 600mm c/c bothways well notched and screwed with 25mmx25mmx4mm aluminium angles including necessary beadings, approved adhesive and necessary hardware etc. complete as per detailed drawing and design and Fixing 4mm thk approved teak veneer on provided ply panelling including necessary beadings, approved adhesive, necessary hardware inlcuding melamine matt polish to all exposed surface etc. complete as per detailed drawings.

Item No:138 Providing & fixing trap door in ceiling of size 600mm x 900mm made up of 19mm marine plywood and 4mm thk approved veneer finshed with melamine polish inclusive of approved fixtures and fittings as per design and drawings etc. complete.

Item No:139 Providing and making curtain pelmet using 19mm marine ply and finishing front with 12mm gypsum board with all necessary hardware etc. complete.

Item No:140 Three Seater Sofa - Providing and supplying three seater sofa of size 1950X760X825 mm ht made out of 75X38mm (finished size) CPTW section frame 6 mm marine plywood generally confirming to IS 303/IS 710-17980 for necessary covering from back and armrest .The seat shall be of 100mm thhick Dunlop or MM or equivalent brand quality foam covered by 1 inch sofa foam and arms having CCTW 50 mm thick 50 density branded foam covered 1 inch plain soft for all work covered with tapestry fabric upto Rs 400/smt including necessary hardware never jute cloth casement springs or belted absorber complete all exposed wooden surfaces shall be melamine polished complete per architects drawing and instruction of engineer in charge.

Item No:141 Two Seater Sofa - Providing and supplying two seater sofa 1350x760x825mm ht made out of 75X38mm (finished size) CPTW section frame 6 mm marine plywood generally confirming to IS 303/IS 710-17980 for necessary covering from back and armrest .The seat shall be of 100mm thhick Dunlop or MM or equivalent brand quality foam covered by 1 inch sofa foam and arms having CCTW 50 mm thick 50 density branded foam covered 1 inch plain soft for all work covered with tapestry fabric upto Rs 400/smt including necessary hardware never jute cloth casement springs or belted absorber complete all exposed wooden surfaces shall be melamine polished complete per architects drawing and instruction of engineer in charge.

Item No:142 One Seater Sofa - Providing and supplying One seater sofa of size 750 mm x 600 mm made out of 75X38mm (finished size) CPTW section frame 6 mm marine plywood generally confirming to IS 303/IS 710-17980 for necessary covering from back and armrest .The seat shall be of 100mm thhick Dunlop or MM or equivalent brand quality foam covered by 1 inch sofa foam and arms having CCTW 50 mm thick 50 density branded foam covered 1 inch plain soft for all work covered with tapestry fabric upto Rs 400/smt including necessary hardware never jute cloth casement springs or belted absorber complete all exposed wooden surfaces shall be melamine polished complete per architects drawing and instruction of engineer in charge.

Item No:143 Providing and Supplying L- Shaped 3 Seater Sofa of Elantra or equivalent make in Synthetic Leather in Dark Brown in required position of size 2100mmX600mm as directed by Engineer in chanrge., Complete.

Item No:144 Providing and Supplying L- Shaped 6 Seater Sofa of Size 3600mmX600mm Elantra or equivalent make in Synthetic Leather in Dark Brown in required position as directed by Engineer in charge.

Item No:145 Providing and making Luggage Rack 900mm X500 to 600mm made up of teakwood frame of size 100mmx50mm and battens 50mmx50mm placed at 75mm c/c and finishing with melamine polish as per approved design and drawings etc. complete.

Item No:146 Providing and Supplying approved quality of two level Reception counters 3100 X 500mm having 50mm top and sides made of 19mm ply, top row of 125mm deep drawer and having arrangement for display on front covered with 12mm thk Alabaster sheet finished with veneer on top and 1mm thk laminate on inner side including necessary hardware etc. complete.as per drawing and design complete.

Item No:147 Providing and fixing TV unit drawers cum shelf of size 1150mmx450x300mm made up of 19mm thk marine plywood, 4mm thk approved veneer for exposed faces and 1mm thk approved laminate for unexposed faces, finished with melamine polish, using approved fixtures as per approved design and drawings etc complete. etc. complete.

Item No:148 Providing & Fixing Curviliner Workstation @ 1500/1500Lx600/600Dx750HT Providing & Fixing Curviliner Workstation @ 1500/1500Lx600/600Dx750HT, Curvilinear Table Top @ 1500/1500Lx600/600D :- TOP to be made of 25 mm thick Prelaminated particle board with PVC edge band, GABLE END to be made of 25 mm thick Prelaminated particle board with PVC edge band, KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated - Black Color, CPU TROLLEY :- Metal Powder Coated - Black Color, along with 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. 3 Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board.

Item No:149 Executive Table @ 2250Lx2100Dx750HT including Low Height Credestal @ 1200Lx450Dx650HT Providing & Fixing of Table @ 2250Lx2100Dx750HT TOP & GABLE END to be made of Membrane finish with soft water fall edges & curved panel &Decorated Anodized section MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band. INCLUDING CREDESTAL @ 1200L X 450D X 650H :- To be made out of Membrane Finish ( 2 Openable Shutter & 3 Drawer Pedestal in between ) as per drawing.

Item No:150 Providing and Fixing Pigeon holes 300 mm deep made up of 19mm thk marine plywood, 4mm thk approved veneer for exposed faces and 1mm thk approved laminate for unexposed faces, finished with melamine polish, using approved fixtures as per approved design and drawings etccomplete.

Item No:151 Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38 mm round Aluminium channel with Black out fabric &telting with chain (Ball) system with all necessary fixtures and fitting etc.complete.(Sample to be final by Engineer In-charge prior execution of work).

Item No:152 Providing and Supplying Carpets in Public areas of Welspun 1800 GSM/ Sleepwell or equivalent make or directed by Engineer in charge Complete.

Item No:153 Providing and Supplying Rugs in Public areas of Welspun 1800 GSM/ Sleepwell or equivalent make or directed by Engineer in charge Complete.

Item No:154 Providing & fixing Sleepwell-Durafirm Mattress for single bed of size 6'6'' X 3' X 150' mm as directed by Engineer in charge., Complete.

Item No:155 Providing & fixing Sleepwell-Durafirm Mattress for double bed of size 6'6'' X 6' X 150' mm as directed by Engineer in charge., Complete.

Item No:156 Providing & Supplying Indulgence Pillows, etc of sleepwell or approved make or direcetd by engineer in charge etc Complete.

Item No:157 Providing & Supplying set of Bed Sheets and Pillow covers Sleepwell or equivalent make.

Item No:158 Providing and Supplying Sleepwell Solace Blankets/Duvet Etc Complete.

Item No:159 Providing and Supplying Quilts of sleepwell/duvet make or of approved make or as per directed by engineer in charge etc complete.

Item No:160 Providing & fixing in position main curtain make of (GM/ Bombay dying or equivalent) with balance rod of approved quality & other required fixtures applied with power coating etc. provided with tussels to hold the curtain at one side of the wall, necessary feetings complete as directed by Engineer Incharge.

Item No:161 Providing & fixing in position sheer curtain make of (GM/ Bombay dying or equivalent) with balance road of approved quality & other required fixtures applied with power coating etc. provided with tussels to hold the curtain at one side of the wall, necessary feetings complete as directed by Engineer Incharge.

Item No:162 Providing and supplying Turkish Type Bath Towel of Bombay Deying or Equivalent make of Approved Quality by Enginner-in charge.

Item No:163 Providing and supplying Turkish type (Face Towel) napkins of Bombay Deying or Equivalent make of Approved Quality by Enginner-in charge.

Item No:164 Providing artifects in rooms and passages and in public areas

Item No:165 Providing and fixing at position Murals, paintings,statues , artwork etc as per requirement.

Item No:166 Supplying of SS 7 lit Dustbins.

Item No:167 Providing and Laying at position approved quality of planters boxes in size as per drawing.

Item No:167(i) 200 dia X 300 ht

Item No:167(ii) 150 dia X 450 ht

Item No:167(iii) 150 dia X 1050 ht

Item No:168 Providing and Fixing Sky Light Dome Work at terrace with structural steel work and polycarbonate sheet (Providing & Fixing of 65mm x 65mm x 3mm MS Square Pipe for Main member, 35mm x 35mm x 3mm MS Square Pipe for Perlin member, 65mm x 65mm x 3mm MS Square Pipe for Bending member at every 1 mtr, 8mm MS Plate and Epoxy Paint. After that with Necessary hardware like Aluminium Section, Rubber Gasket, Self Tapping Screws, Washer and Silicon Sealant shall be used to fixed 10mm thick Multiwall Polycarbonate Sheet. As Per Colour Approval.) Size- 5.80 Mtr Dia x-height 3.50 Mtr( Approx)

Item No:169 Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth/murum, ramming ,watering including shoring and strutting etc. complete. (Lift from 1.5m To 3.0 m.) By Mechanical Means

Item No:170 Filling in plinth and floors with contractor's soil, sand or murum in 15 centimetre to 20 centimetre layers including watering and compaction etc. complete.

Item No:171 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc.complete.

Item No:172 Providing and casting in situ cement concrete in Mix-20 grade of trap/granite/ quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/steel formwork, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag,plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based Programmable Logic Controller (PLC) with Supervisory Control And Data Acquisition (SCADA) enabled reversible Drum Type mixer /Concrete bathch mix plant (Pan mixer) etc complete with natural sand/ Vertical Shaft Impactor quality artificial sand.

Item No:173 Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No:174 Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No:175 Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No:176 Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No:177 Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning, preparing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days etc complete.

Item No:178 Providing and fixing mild steel grill gate with angle iron frame 65mm x 65mm x 10mm with iron bars at 150mm C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kg/Smt.

Item No:179 Providing and Fixing Stainless Steel Vertical Freezer -300 lit Capacity of approved make or as directed by engineer in charge.

Item No:180 Providing and Fixing Stainless Steel Water Cooler capacity of 80L approved make or as directed by engineer in charge.(Voltas Water Cooler SS body/Blue star water cooler)

Item No:181 Providing and Fixing Stainless Steel Vertical Racks with Shelves of Size 800mm X 600mm X 2100mm approved make or as directed by engineer in charge

Item No:182 Providing and Fixing Stainless Steel Serving Table of Size 1200mm X800mm X 2100mm approved make or as directed by engineer in charge

Item No:183 Providing and Fixing Stainless Steel Working Platform with 3 Sink of Size 2490mm X 700mm X 830mm approved make or as directed by engineer in charge

Item No:184 Providing and Fixing Stainless Steel Cold Storage Refrigerator of Size 1650mm X 750mm X 830mm approved make or as directed by engineer in charge

Item No:185 Providing and Fixing Stainless Steel working platform with Shelves of Size 2000mm X 770mm X 830mm approved make or as directed by engineer in charge

Item No:186 Providing and Fixing Stainless Steel Stove with 2 Burner with Iron grill and Oven of Size 1500mm X 900mm X 830mm approved make or as directed by engineer in charge

Item No:187 Providing and Supplying Stainless Steel Sink Table of Size 830mm X 900mm X 830mm approved make or as directed by engineer in charge

Item No:188 Providing and Fixing Stainless Steel Square Tandoor of Size 900mm X 900mm X 1040mm approved make or as directed by engineer in charge.

Item No:189 Providing andFixing Stainless Steel Working Platform with 1 Sink of Size 1200mm X 740mm X 830mm approved make or as directed by engineer in charge.

Item No:190 Providing and Fixing Stainless Steel Stove with3 Burner with Iron grill and Oven of Size 3500mm X 800mm X 830mm approved make or as directed by engineer in charge.

Item No:191 Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 5.0 to 9.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Item No:192 Providing and laying Cast in situ/Ready Mixcement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No:193 Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer)etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No:194 Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No:195 Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing for basement or underground floor on a base of Cement concrete 1:3:6, including sub base of 2.50 centimeter thick Cement mortar 1:3 with conceal, secrete (RMW), Algae proof or other alike waterproofing liquids, raking of joints upto 35 mm depth, filling the joints with 6 mm size crushed metal, hand grouting with cement slurry, curing and cleaning, with 7 years guarantee on court fee stamp of Rs. 100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete )

Item No:196 Providing and fixing 20 to 25 mm thick rough shahabad box type waterproofing treatment to vertical outside faces of Reinforced Cement concrete walls of basement or underground floor including filling the gap of 25 mm between rough shahabad and R.C.C. walls with cement grout mixed with water proofing liquid Algae proof or other alike with one tile lift method, brushing the joints horizontally with cement slurry mixed with water proofing liquid for width 30 to 35 mm and sloping coping over topmost tile with cement mortar 1:3 butting the bottom most with Cement concrete 1:2:4 mixed with water proofing liquid, curing, with 7 years guarantee on court fee stamp of Rs.100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete)

Item No:197 Providing and application of integral crystalline waterproofing treatment for retaining wall by using to entire quantity of the concrete penetron admix having speed of penetration of 31 CM in 56 days and resistance to 20 bar hydrostatic water head of M/s ICS penetron international Ltd USA @ 0.8% by weight of cementitious content .The material must qualify as PRAH grade PERMEABILITY REDUCING ADMIXTURE FOR HYDROSTATIC conditions and meet the following requirements specified in ACI -212-3R -2010 at the recommended dosage rate of 0.8% by weight of cementitious material which is capable of reducing permeability co efficient calculated as 4 cycles of hydrostatic pressure. and permeability coefficient calculated as per Valenta/Darcy formula and using approved as per DIN 1048 with chloride content content less than 0.1% alkali content less than 9.3% and no negative effect on corrosion of steel reinforcement . work shall be executed by certified applicator only and shall be guaranteed for 10 years against any leakages and guarantee shall be provided on 500/- stamp paper in approved performa.

Item No:198 Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete.

Item No:199 Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. (Ground Floor)

Item No:200 Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces in one coat including scaffolding, preparing the surfaces. (excluding the primer coat.)etc. complete.

Item No:201 Providing and fixing mild steel grill work for windows, ventilators etc 20 kg/sqm as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Item No:202 Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Item No:203 Supplying composite resin manhole cover and frame of dia 600 mm size and having load capacity of 2.5 tonnes confirming to EN -124 1994 product shall have top abrasion resistant layer of decorative grey granite finish confirming to test performed as per IS 15658-2006 It shall also confirm permanent set criterion aas per EN -124 product shall be tested in NABL accredited test lab for load capacity and permanent set.

Item No:204 Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed.. (with prior permission of SE)

Item No:205 Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader / Paver on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material.

Item No:206 Providing and laying 125 micron Low DensityPolyethylene (LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete.

Item No:207 Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, , cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant / Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor / by suitable means as approved by Engineer -incharge , compacting with vibratory roller , finishing, curing and including preparation of sub-grade surface if required etc. complete.

Item No:208 Providing, cutting, bending, hooking, tying and laying in position TMT FE 500 steel bars for reinforcement for all RCC works as per detailed drawings etc. complete.

Item No:209 Providing and laying in-situ M40 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement , coarse and fine aggregate conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant / non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver ,compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer -in-charge and curing by curing compound / by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 mm at bottom and 40 mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer -in-charge.

Item No:210 Providing and Laying Granite Cobble Stones flooring 100x100x75mm at entrance by preparing ground/sub base,laying mortar base for granite setts,filling of joints,pointing etc. according to design pattern as directed by engineer-in-charge.

Item No:211 Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Mechanical Means

Item No:212 Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Item No:213 Providing uncoursed rubble masonry of trap / granite / quartzite /gneiss stones in cement mortar 1:6 in foundation and plinth of inner walls / in plinth of external walls including bailing out water manually , striking joints on un exposed faces and watering etc. complete.

Item No:214 Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

Item No:215 Free Standing Table @ 1200Lx600Dx750HT Providing and fixing Table of Size 1200 x 600 x 750 mm. Top: made from 25 mm Prelaminated Particle board. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated -Black Color, CPU TROLLEY :- Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board.

Item No:216 Supplying & laying HMS PVC conduit 20 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Item No:217 Supplying & erecting HMS P.V.C. conduit 25 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Item No:218 Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Item No:219 Concealing of provided G.I. pipe/H.G. screwed conduit/PVC pipe in wall/floor/false ceiling complete as per specification No: WG-PW/CW

Item No:220 Supplying and erecting UPVC reinforced flexible conduit 25 mm in dia. conforming to I.S. with required number of couplings, PVC bushes, check nuts etc. complete.

Item No:221 Supplying and erecting PVC box trunking of size 50x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Item No:222 Supplying and erecting PVC box trunking of size 75x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Item No:223 Supplying and erecting PVC box trunking of size 75x75 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Item No:224 Supplying and erecting PVC box trunking of size 100x50 mm. with accessories on wall/ceiling as per specification No: WG- MA/BOX .

Item No:225 Supplying and erecting PVC slotted box trunking of size 75x75 mm. with accessories on wall/ceiling as per specification No: WG-MA/SLBOX.

Item No:226 Supplying and erecting PVC slotted box trunking of size 100x100 mm. with accessories on wall/ceiling as per specification No: WG-MA/SLBOX.

Item No:227 Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Item No:228 Supplying & erecting mains with 2x2.5 sq.mm. and earth wire 1.5 sq.mm FRLSH PVC copper wire in HMS PVC conduit min. 20mm dia. as per specification No: WG-MA/PC.

Item No:229 Supplying & erecting mains with 2x4 sq.mm. and earth wire 2.5 sq.mm FRLSH PVC copper wire in HMS PVC conduit min. 20mm dia, as per specification No: WG-MA/PC.

Item No:230 Supplying & erecting mains with 3x10 sq.mm. and earth wire 6 sq.mm FRLSH PVC copper wire, in HMS PVC conduit min. 25mm dia, as per specification No: WG-MA/PC.

Item No:231 Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Item No:232 Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Item No:233 Supplying and erecting ISI mark modular type switch one way 16 / 20 A, duly erected on provided plate and box with wiring connections complete with neon indicator.

Item No:234 Supplying and erecting ISI mark modular type D.P. switch 32A with indicator, duly erected on provided plate and box with wiring connections complete.

Item No:235 Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No:236 Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No:237 Supplying and erecting ISI mark modular type T.V. socket single outlet, duly erected on provided plate and box with wiring connections complete.

Item No:238 Supplying and erecting ISI marked modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Item No:239 Supplying and erecting ISI mark modular type buzzer 220 / 250V, duly erected on provided plate and box with wiring connections complete.

Item No:240 Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete. Note: Add Rs 57/- for additional two module box with double mounting plate if required.

Item No:241 Supplying and erecting PVC Surface modular switch box with double mounting plate for 2 modules duly erected.

Item No:242 Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Item No:243 Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Item No:244 Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Item No:245 Point wiring for light/fan/bell in 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm (2+1E) FR grade copper wire, flush type switch, earthing and required accessories as per specification No: WG-PW/SW. Fan Point

Item No:246 Point wiring for light/fan/bell concealed type in min 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm. (2+1E) FR grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW

Item No:247 Point wiring for independent plug, concealed type in min 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm (2+1E) FR grade copper wires, modular type switch and socket, earthing and required accessories as per specification No WG-PW/SW

Item No:248 Wiring for plug on board with Switch socket concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Item No:249 Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW( Fan pt.)

Item No:250 Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW..Light Point

Item No:251 Point wiring for independent plug in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E ) FR grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW.

Item No:252 Supplying & erecting telephone copper cable 4 pair with 0.5 mm dia. laid in provided PVC casing capping / conduit as per specification No. WG-TW

Item No:253 Supplying & erecting jelly filled unarmoured telephone copper cable 20 pair with 0.5 mm dia. laid in provided PVC casing capping / conduit as per specification No. WG-TW

Item No:254 Supplying & erecting jelly filled armoured telephone copper cable 50 pair with 0.5 mm dia. laid in provided trench as per specification No. WG-TW

Item No:255 Supplying & installing co-axial copper cable low voltage grade RG-6 as per specification No. WG-TW

Item No:256 Supplying, installing, testing & commissioning internet protocol digital type EPABX for 10 IP extensions complete.

Item No:257 Supplying, installing, testing & commissioning push button telephone instrument desk top/wall mount with caller ID unit as per specification complete.

Item No:258 Supplying, installing, testing & commissioning approved type Digital key telephone / IP telephone instrument as per specification complete.

Item No:259 Supplying & installing UTP networking cat-6+ cable suitable for LAN / WAN Computer net-working as per specification no. WG-COC/NC complete.

Item No:260 Supplying and fixing 1 meter length, UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Item No:261 Supplying and fixing 3 meter length, UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Item No:262 Supplying and fixing tool-less Information Outlet (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Item No:263 Supplying and erecting LED square / circular 16 to 20W down lighter having pressure die-cast aluminium housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Item No:264 Supplying and erecting square shaped CRCA /die-cast aluminium powder coated housing LED panel light (slim edge-lit) 600x600mm suitable for 36 W-40W with provision for plane front frame with translucent cover fixed to the housing complete.

Item No:265 Supplying & erecting LED 18W tube light fitting (4 feet) with polycarbonate housing, heat sink, integrated HF electronic driver complete

Item No:266 Supplying and erecting regular/ standard model ceiling fan of 600mm. sweep complete erected in position as per specification no. FG-FN/CF

Item No:267 Supplying Pedestal fan 400 mm. 230 Volts 50 cycles oscillating type complete with guard and regulator 3 mtrs. of flexible wire and hand shield type 3 pin plug top.

Item No:268 Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 300mm. 1400 RPM rust proof body & blades, wire mesh, duly erected in an approved manner.

Item No:269 Supplying and erecting five star rated energy saving Ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Item No:270 Supplying & erecting on line UPS pure sine wave of 10 kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins battery backup, as per specification no. AP-UPS.

Item No:271 Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB.

Item No:272 Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB

Item No:273 Supplying, erecting & marking DPMCB 6A to 32A, C- series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Item No:274 Supplying, erecting & marking FPMCB 6A to 32A in provided distribution board as per specification no. SW-SWR/MCB

Item No:275 Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-

Item No:276 Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SPMCB of 12 ways, on iron /GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Item No:277 Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SP / TP MCBs of 24 ways on iron/ GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Item No:278 Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 10 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Item No:279 Supplying & erecting original 1.25 mm CRCA sheet metal enclosures with 20A. 2 pin plug & earth socket and 20A. 3 pin plug top with 20A/30A single pole MCB complete erected on angle iron/ GI frame.

Item No:280 Providing & erecting 4 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB

Item No:281 Supplying, fixing and commissioning 2 pole,RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6/10/16/20/25A, as per specification no SW-RCCB/RCBO

Item No:282 Supplying, fixing and commissioning 2 pole RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 32A/40A as per specification no SW- RCCB/RCBO

Item No:283 Supplying and erecting 250 kVAr, 440 V three phase, 50 Hz., thyrister switched micro APFC passive filter panel, consisting of suitable steps of APP type capacitor units with harmonic filter reactors, as per specification no CP-ED/APFC

Item No:284 Supplying, erecting & terminating XLPE armoured cable 4 core 10 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification

Item No:285 Supplying, erecting & terminating XLPE armoured cable 4 core 16 sq. mm. copper conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification.

Item No:286 Supplying, erecting & terminating XLPE armoured cable 4 core 25 sq. mm. copper conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification.

Item No:287 Supply, Installation, Testing and commissioning of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly

Item No:288 Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no.EA-EP.

Item No:289 Supplying and erecting Annealed bare copper wire of high purity of different sizes used for earthing on wall with necessary copper clamps fixed on wall/cable/conduit with screws in an approved manner.

Item No:290 Supplying and erecting PVC ROHS complied Non flame propagating under floor ducts/raceways of 90mm Width x 35 mm depth x 3000 mm Length including the connectors and the clamps at required intervals. The ducts shall be in trapezoidal shape tested for 750 N point load suitable for inscreed application as per specification no. WG-MA/UFD. ( NCSR)

Item No:291 Supplying and erecting underfloor junction box of size 150mm x 150mm x 55 mm with flush finish powder coated appearance having knock outs for UPVC duct entry of size 60x25 mm width and 95x35 mm ducts complete as per specification no. WG-MA/UFB. (NCSR)

Item No:292 Supplying and erecting of underfloor junction box of size 200mm x 200mm x 55 mm. with flush finish powder coated appearance having knock outs for UPVC duct entry of size 60x25 mm and 95x35 mm ducts complete as per specification no. WG-MA/UFB . (NCSR)

Item No:293 Supplying and erecting of underfloor junction box of size 300mm x 300mm x 55 mm. With flush finish powder coated appearance having knock outs for UPVC duct entry of size 60x25 mm and 95x35 mm ducts complete as per specification no.WG-MA/UFB . (NCSR)

Item No:294 Supplying and Erecting LED TV

Item No:295 Printer

Item No:296 DeskTop Computer

Item No:297.1 SITC of Electric Traction Passenger Lift with · Rated capacity :- 8 Passenger/544Kg· Floors :- G+1 floor (2Stops/2 Landings) · Travel :- 3 to 4.2 mtrs· Location of Lift Machine:- MR/MRL·Rated speed :- 1.0mps VS· *Doors type :- COPO/TOPO Doors with frame having clear opening of 800 mm wide x 2000 mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves/frames. * Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. * COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with/without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor. * Clear Car size of ......mm wide x ......mm deep x ......mm high * LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings* Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port, control panel duly wired with proper size & strength copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class* ARD complete with necessary SMF VRLA batteries* Fireman controller having fireman switch at fire Landing, * CCTV surveillance system comprises of 2nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for 60 days with 18" FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. * Lift Machine of Gearless PMSM of suitable kW with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength * Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work * Minor civil work for alteration if any and erection of door frames and accessories, erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails fixing of girders for mounting lift machine etc. complete as per specification no. LFT. Lift shaft available having clear size of ...mm wide x ..mm deep. ..mm Pit depth, …mm Overhead.

Item No:297.2 For lift travelling up to six floor or at a speed of 1 mps add as below,For Lift having 800mm wide x 2000mm high clear entrance in 1.5mm thick SS 304 grade landing door [Two panel], this includes all necessary accessories like LOP's with UP/DN buttons-arrows-indicators, extension of guide rails, shaft wiring with trunking, traveling cables, main hoisting ropes/belts, & OSG rope landing doors with all accessories etc. necessary for the normal safe functioning of lift installation complete.

Item No:298.1 SITC of Electric Traction Passenger Lift with Rated capacity :- 13 Passenger/680Kg· Floors:- G+1 floor (2Stops/2 Landings) Travel :- 3 to 4.2 mtrs. Location of Lift Machine:- MR/MRL·Rated speed :- 1.0mps VS · Doors type :- COPO/TOPO Doors with frame having clear opening of 900/1000mm wide x 2000 mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves/ frames Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with/without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor Clear Car size of ......mm wide x ......mm deep x ......mm high LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port, control panel duly wired with proper size & strength copper wire for power & control circuit, with provision for addition of floor /control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class · ARD complete with necessary SMF VRLA batteries · Fireman controller having fireman switch at fire Landing, · CCTV surveillance system comprises of 2nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for 60 days with 18" FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. Lift Machine of Gearless PMSM of suitable kW with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work Minor civil work for alteration if any and erection of door frames and accessories,erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails fixing of girders for mounting lift machine etc. complete as per specification no. LFT. Lift shaft available having clear size of 1900mm wide x 2100mm deep, ......mm Pit depth, ………mm Overhead

Item No:298.2 Add on For Lift travelling up to six floors or at a speed of 1.0 mps, add as below, For Lift having 800mm wide x 2000mm high clear entrance in 1.5mm thick SS 304 grade landing door [Two panel], this includes all necessary accessories like LOP's with UP/DN buttons-arrows-indicators, extension of guide rails, shaft wiring with trunking, traveling cables, main hoisting ropes/belts, & OSG rope landing doors with all accessories etc. necessary for the normal safe functioning of lift installation complete

Item No:299 Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 mm with accessories on wall/ceiling as per specification No: WG-MA/CON

Item No:300 Supplying & erecting mains with 1x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No:301 Supplying & erecting mains with 2x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No:302 Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Item No:303 Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete

Item No:304 Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 modules duly erected.

Item No:305 Wiring for plug on board with Switch socket, copper wiring and earthing as per specification No: WG-PW/SW

Item No:306 Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire, flush type switch, earthing and required accessories as per specification No: WG-PW/SW

Item No:307 Point wiring for independent plug in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire with flush type switch and required accessories as per specification No: WG-PW/SW

Item No:308 Supplying & erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.

Item No:309 Supplying and erecting bulkhead fitting suitable for upto LED upto 12W fixed on wall. As per specification no. FG-IDF/BHF

Item No:310 Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Item No:311 Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 450 mm. 1400 RPM complete erected in position as per specification no. FG-FN/EXF

Item No:312 Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB

Item No:313 Supplying, erecting & marking DPMCB 40A to 63A, B- series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB

Item No:314 Supplying and erecting single pole and neutral distribution board (SPNDB) surface/flush mounted with 2 ways for incoming and 6 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Item No:315 Supplying & erecting CRCA sheet metal one way enclosures suitable for DP MCB /TP MCB /FP MCB erected on angle iron/GI frame complete.

Item No:316 Supplying, fixing and commissioning 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 32A/40A as per specification no SW-RCCB/RCBO

Item No:317 Supplying, erecting & terminating XLPE armoured cable 2 core 2.5 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as peर specification.

Item No:318 Supplying, erecting & terminating XLPE armoured cable 2 core 4 sq mm copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification

Item No:319 Supplying, erecting & terminating XLPE armoured cable 4 core 10 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification.

Item No:320 Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Item No:321 Supplying, installing, testing and commissioning with perfect aligning, proper levelling of fire service main multi stage pump, of 2800 LPM at 76 m head centrifugal type, 75 HP (55 kW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per Specification.

Item No:322 Supplying, installing, testing and commissioning with perfect aligning, proper levelling of jockey pump of 240 LPM at 56 m head, 15 HP (11 kW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per specification no. FF-

Item No:323 Supplying, installing, testing and commissioning with perfect aligning, proper levelling of booster pump of 450 LPM at 35 m head 7.5 HP (5.5 KW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per specification no. FF-MFP/BP.

Item No:324 Providing Fully Compressive maintenance for items no. 321,322, 323 for 1st year

Item No:325 Providing Fully Compressive maintenance for items no. 321,322, 323 for 2nd year

Item No:326 Providing Fully Compressive maintenance for items no. 321,322, 323 for 3rd year

Item No:327 Supplying, , erecting, testing and commissioning software based Wireless addressable Loop Centralised Monitoring Station with two way communication & Control Room.

Item No:328 Server based Integrated with wireless FDA Digital IP based Voice Evacuation System.

Item No:329 Wireless Addressable Smoke Cum Heat Detector with Two way communication.

Item No:330 Wireless Addressable IR3 Flame Detector with Two way communication.

Item No:331 Wireless addressable Manual Call point with Two way communication.

Item No:332 Wireless addressable Local Hooter Control Panel with Two way Communication.

Item No:333 IP based Digital Amplifier (200w) .

Item No:334 VOIP interface device with Audio out ( Barix ).

Item No:335 Audio Speakers (6w).

Item No:336 Fitting accessories, Fiber optic switch, fiber optic cable, amplifier racks etc.

Item No:337 Wireless addressable gas detector with two way communication

Item No:338 Micro-Communicator.

Item No:339 Supplying & erecting mains with 4x16 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside

Item No:340 Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-

Item No:341 Supplying, fixing and commissioning MCB type change over switch 4 pole, 63A with 3 positions (I-O-II) with centre off position as per specification no. SW-SWR/MCBCOS

Item No:342 Providing, erecting and commissioning 4 pole RCCB only of electromagnetic type with 30/100/300 mA sensitivity and having capacity of 40A complete as per specification no. SW-RCCB/RCCB

Item No:343 Supplying, fixing and commissioning 4 pole RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 63A as per specification no SW-RCCB/RCBO

Item No:344 Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected

Item No:345 Supplying, erecting & terminating XLPE armoured cable 4 core 4 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification

Item No:346 Supplying & laying (including excavation) 15 cm dia RCC Hume pipe with coupling collar of standard thickness at required depth up to 90 cm below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make.

Item No:347 Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Item No:348 Supplying and erecting submersible pump set suitable for erection on open well of 5.625 KW/7.5 HP with 415 V 50 c/s.A.C. supply, having delivery head from 36 to 18 m and discharge from 400 to 1000 Itrs. per minute (Max efficiency at 29 m head & 680 Itr discharge.

Item No:349 Supplying and erecting flat flexible 3 core 4 sq mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Item No:350 Supplying & erecting automatic control panel for 3 Ph, 415 volt, a.c. Submersible/centrifugal pump set for 7.5 to 10 HP consisting of DOL starter having relay range 28-42 AMP,S.P.P., Combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powde

Item No:351 Supplying and erecting ISI mark GI pipe 50 mm dia.‘B’ class at position with accessories complete. Specification no. CW- PLB/GP.

Item No:352 Supplying and erecting 50 mm dia. gun metal sluice valve at position with necessary materials complete.

Item No:353 Supplying and erecting non return valve 50 mm dia in position made of gun metal complete.

Item No:354 Supplying, installing, testing and commissioning of FPC solar water heating system without heat exchanger type of 500 LPD capacity a complete. Specification no. ESD-SHWS-FPC.

Item No:355 Supplying and erecting GI pipe 25 mm dia B class with resin bonded flap rock wool/glass wool insulation, with necessary material complete. Specification no. (ESD-HWP/TGP)

Item No:356 Supplying and erecting GI pipe 40 mm dia B class with resin bonded flap rock wool/glass wool insulation, with necessary material complete. Specification no. (ESD-HWP/TGP)

Item No:357 Supplying, installing, testing and commissioning solar street light pole comprising of 14W LED fitting, 12V 36Ah maintenance free lithium battery, min. 75Wp SPV module, MS powder coated battery box weather proof, mounted on 75/80 mm dia. B-Grade GI pole.

Item No:358 Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-

Item No:359 Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at th

Item No:360 Supplying, erecting & terminating XLPE armoured cable 4 core 10 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no.

Item No:361 Supplying and erecting Centrifugal water pump (Monoblock), 230V, Single phase 50 cycles A.C. supply of 0.75 KW/1 HP with discharge 1.6/2.9 Litres per second (LPS) for head of 9/22 m & 40 mm suction/ 40 mm delivery pipe on provided C.C. foundation as per specification.

Item No:362 Supplying and erecting 25 mm dia. gun metal sluice valve at position with necessary materials complete.

Item No:363 Supplying and erecting non return valve 25 mm dia in position made of gun metal complete

Item No:364 Providing Fully Compressive maintenance for items no.354 to 363, for 1st year

Item No:365 Providing Fully Compressive maintenance for items no. 354 to 363, for 2nd year

Item No:366 Providing Fully Compressive maintenance for items no. 354 to 363, for 3rd year

Item No:367 Supplying & erecting H.M.S. P.V.C. conduit 20 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Item No:368 Supplying and erecting PVC Surface modular switch box with double mounting plate for 1 module complete duly erected.

Item No:369 Supplying & installing UTP networking cat-6 armoured cable suitable for LAN / WAN Computer net-working as per specification No. WG-COC/NC

Item No:370 Supplying and fixing 3 meter length, UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Item No:371 Supplying, fixing, and configuring ethernet managed ethernet switch of 24 ports with 2 SFP + 2 combo port and web view/CLI on provided rack or as directed as per specification no. WG-NWC/GBS

Item No:372 Supplying, installing & testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC.

Item No:373 Supplying and fixing tool-less Information Outlet (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Item No:374 Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Item No:375 Supplying and fixing 12U wall mount rack (Dimension-DxWxH – 450x550x635 mm) as per specification No. WG- NAS/RAK

Item No:376 Supplying, fixing, and configuring 8-ports managed gigabit switches layer-2, 10/100/1000 base-T PoE smart switch plus 2 SFP only complete.

Item No:377 Supplying & erecting on line UPS pure sine wave of 2 kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins battery backup, as per specification no. AP-UPS

Item No:378 Supply, Installing, Testing & Commissioning of IP Bullet Camera Having 4 MP HD WDR IR Bullet Camera 50 Mtr1/3” 4 MP PS CMOS Image Sensor. Max 25/30 fps@ 4 MP (2688 x1520) H 265 and H 264 triple – Stream encoding. WDR (120 db), Day / Night (ICR), 3 DNR, AWB, AGC, BLC, HLC, 2.7- 13.5 mm motorized lens IR Range of 50 Mtrs, Micro SD Card, IP67, IK 10, ePoE Mobile Software, iCMOB, gCMOB CMS Software, KVMS ProvOptimusProlmage Sensor, 1/3” 4 MP Progressive Scan CMOS Effective Pixels: 2688 (H) x 1520 (V) Minimum illumination: 0.0 Lux/ F1.4 (Color, 1/3s, 30 IRE) 0.3 LUX/f1.4 (COLOR, 1/30S, 301RE) 0 Lux/f1.4 (IR on) Shutter Speed: Auto/Manual1/3~ 1/100000s White Balance: Auto / Natural / Street Lamp / Outdoor Manual Lens: 2.7 mm ~ 13.5 mm Motorized Lens Gain Control (AGC): Auto / Manual Angle of View: H: 1060 ~310, V: 580 ~ 170 Video Compression: H 265 +/ H 265 / H 265+/H265 Back Light. Compensation: BLC/HLC/WDR(120dB) S/N Ratio, More than 50 dB Video Streaming, Main Stream: 4 MP (1~25/30 fps), Sub Stream: D1(1~25/30 fps), Third Stream, 720p (1~25/30 fps) Resolation 4M(2688 x 1520) / 3M (2304 x 1296) / 1080P (1920 x 10801) / 1.3 M (1280 x 960) / 720P(1280 x 720) / D1 (704 x 576/704 x 480) / VGA (640 x 480 ) / CIF (352 x 288 / 352 x 240) Digital Zoom: 16 x Motion Detection, Off/On(4 Zone. Rectangle) Privacy Mask, off/on (4 Zone, Recangle) ICR: Auto (ICR) / Color / B / WROI , off / on (4 Zone) Audio Input: I Channel Audio output: 1 Channel AudioCompression: G711a / G 711 Mu / AAC / G 726 Alarm In: 2 Channel Alarm Out, 1 Channel Protocol, HTTP, HTTPs, TCP, ARP, RTSP, UDP, SMTP, FTP, DHCP, DNSDONS: PPPOE, IPv4/v6, QoS, UPnP, NTP, Bonjour, 802, 1X MuLticast, ICMP, IGMP, SNMP, ONVIF, PSIA, CGISmart, Detection, Tripwire Intrusion ObjectMissing / Abandoned Face detection Etherne: RJ-15(10/100 Base) User Account: 20 User Smart Phone, Iphone, iPad, Android Phone IR: IR Range of 50 Mtr

Item No:380 Network Video Recorder of 32 Channels Supply, Installing, Testing & Commissioning of Network Video Recorder of 32 Channels having Upto 32 Ch, Max 12 MP Camera Supported256 MBPS network camera Recording,Support 4K Video out on HDMI Monitor,Support Dual Monitor Video out,Support H.265, H.264 MJEPG compression, Wise Stream Support Max 8 internal HDDs (48 TB), e-SATAT/ iSCSI storage support, Support RAID 5Easy installation with front swap Hard Disc.

Item No:381 Supply, Installing, Testing & Commissioning of 4 TB HD Surveillance Hard Disk Supply and Erecting 4 TB SATA . Surveillance Hard Disk 7200 120MB Catche 2

Item No:382 Supply, Installing, Testing & Commissioning of Monitor LCD, 42 inches or higher, Full HD1. Size : 42 inches, 2. Resolution : Full HD,3. Backlight : LED,4. Brightness : 400 NITS min.,5. Contrast : 1200 :1 or better,6. Power supply :230v + or - 10%,50 Hz

Item No:383 Providing Fully Compressive maintenance for items no.367 to 382, for 1st year

Item No:384 Providing Fully Compressive maintenance for items no. 367 to 382, for 2nd year

Item No:385 Providing Fully Compressive maintenance for items no. 367 to 382, for 3rd year

Item No:386 Supply and installation of 800A sandwitch type Bimetal contact Aluminium busway (3L+N+PE) Epoxy/Mylar insulation 100%N 40kA for 1sec minimum 50% Integral earth housing of minimum 1.6m Electro-galvanized steel rated insulation class F & operating voltage=1000v, IP=54.

Item No:387 Supply and installation of Allum.conductor plug in hole for 800A Sandwitch type bimetal contact Aluminium busway (3L+N+PE)rated insulation class F & operating voltage=1000v, IP=54.

Item No:388 Supplying & erecting All conductor tap off box 4P 125-250A with breaker suitable to fix with 800A Sandwitch type bimetal contact Aluminium busway (3L+N+PE) rated insulation class F & operating voltage=1000v, IP=54.

Item No:389 Supplying & erecting spring hanger for 800A sandwitch type bimetal contact Aluminium busway (3L+N+PE) rated insulation class F &operatin voltage=1000v, IP=54.

Item No:390 Supplying & erecting of end cover for 800A sandwitch type bimetal contact Aluminium busway (3L+N+PE) rated

Item No:391 Supplying & erecting end feed unit with 1000A 50kA TPN microprocessor base release MCCB.

Item No:392 Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-

Item No:393 Providing & erecting 3 Pole MCCB of 250A,415V capacity with short circuit rating 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and

Item No:394 Providing & erecting floor / wall mounting, MCCB panel board with door suitable for four pole incoming 250A, 6 ways four pole outgoing upto 100 A MCCB's on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCB'S)

Item No:395 Supplying and erecting GI sheet 1.25 mm (18 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint.

Item No:396 Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at th

Item No:397 Supplying, erecting & terminating XLPE armoured cable 3½ core 150 sq. mm. aluminium conductor with continuous12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification

Item No:398 Supplying, erecting & terminating XLPE armoured cable 4 core 4 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no.

Item No:399 Supplying, erecting & terminating XLPE armoured cable 4 core 50 sq. mm. copper conductor with continuous 5.48 sq mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification

Item No:400 Supplying & erecting G.I. pipe ‘A’ class 50 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per CB-CEspecification no. CB-CE

Item No:401 Supplying & laying (including excavation) 25 cm dia RCC Hume pipe of standard thickness at required depth up to 90. below road / ground surface, for covering provided cable & necessary back filling with light ramming to make the road/ground surface ascms. below road / ground surface, for covering provided cable

Item No:402 Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Item No:403 Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP.

Item No:404 Supplying, erecting and commissioning of diesel generating set with alternator of 200 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1

Item No:405 Supplying, erecting, testing and commissioning of Microprocessor based AMF panel suitable for diesel generating set of above 180 kVA upto 200 kVA capacity Single/Three phase, 230/415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification

Item No:406 Excavating hard Rock or bituminous road by chiselling for preparing pit for pole / stay/earth plate / for laying cable/ pipe & clearing the site by removing debris & making the site as required complete.

Item No:407 Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

Item No:408 Excvating hard drop by chiselling for pit chember of size 1.2mtr x 1 mmtr x 1 mtr and claring the site by removing the duly plastering including watering ,stretching joints and providing cement concrete filling 1;3;6 ratio with 22 to 25 mm stone metal duly plasterd with necessary curing and providing MS Cover 10 mm thick above chember including MS Frame in approved manner debris and providing burn brick masonary with 1;6 cement mixture

Item No:409 Providing Fully Compressive maintenance for items no.392 to 408, for 1st year

Item No:410 Providing Fully Compressive maintenance for items no. 392 to 408, for 2nd year

Item No:411 Providing Fully Compressive maintenance for items no. 392 to 408, for 3rd year

Item No:412 Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Item No:413 Supplying & laying HMS PVC conduit 32 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Item No:414 Supplying & erecting mains with 3x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No:415 Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Item No:416 Supplying and erecting PVC insulated PVC round sheathed 4 sq.mm (56 no. x 0.30 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Item No:417 Supplying, installing, testing and commissioning split type variable speed inverter technology room Airconditioning unit 1 TR having ISEER minimum 4.50 suitable to operate on capacity 250V, 50 cycles, A.C. supply having 1 no. of air handling unit hi-wall

Item No:418 Supplying, erecting, testing and commissioning 10 HP, VRF / VRV air conditioning system, out door unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacit

Item No:419 Supplying, erecting, testing and commissioning 12 HP, VRF / VRV air conditioning system, out door unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacit

Item No:420 Supplying, erecting, testing and commissioning 14 HP, VRF / VRV air conditioning system, out door unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacit

Item No:421 Supplying, erecting, testing and commissioning 20 HP, VRF / VRV air conditioning system, out door unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacit

Item No:422 Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 0.6TR ( 420 cfm ) / 0.8TR ( 441 cfm ) having EER as per BEE standards and specifications

Item No:423 Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 1.0TR ( 441 cfm ) / 1.3TR ( 512 cfm ) having EER as per BEE standards and specifications

Item No:424 Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 1.5TR ( 512 cfm ) / 1.8TR ( 618 cfm ) having EER as per BEE standards and specifications

Item No:425 Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 2.0TR ( 618 cfm ) / 2.3TR ( 671 cfm ) having EER as per BEE standards and specifications

Item No:426 Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 2.6TR ( 918 cfm ) to 2.8TR ( 1100 cfm ) having EER as per BEE standards and specifications

Item No:427 Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 2 way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 2.8TR ( 1130 cfm ) to 3.7TR ( 1377 cfm ) having EER as per BEE standards and specifications

Item No:428 Supply, installation, testing and commissioning of VRV / VRF based ceiling suspended 6.5TR Treated Fresh Air ( TFA ) ( 5380 cfm ) indoor unit with evaporator fan with motor, copper tube, aluminium fin evaporator coil, washable air filter, insulated drain

Item No:429 Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Item No:430 Supply, installation, testing and commissioning cordless remote contol having colour LCD panel, real time clock, temperature limitation (16 to 30 degree Cent.), functions like filter clean reminder timer suitable to communicate with wired controller compl

Item No:431 Supplying, erecting, testing and commissioning centralised programmable remote contol panel (HMI) touch manager controls minimum 16 system of minimum 64 ODU's can be controlled and up to 992 IDU's can be individually mounted and controlled indoor units .

Item No:432 Supply, fabrication, installation an testing of flexible canvass connections constructed between ductable unit / dampers / ducting of required size with fire resist flexible double canvas sleeve complete.

Item No:433 Providing adhesive thermal insulation for supply / return air duct with 19 mm nitrile rubber insulation having R-value as per the prevailing provisions in ECBC-2007.

Item No:434 Supplying and installation of high pressure grade required size copper connection Y or T- Joints / refnet for liquid and suction line complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testin

Item No:435 Supplying and erecting aluminium powder coated linear grill of suitable size for width length without collar dampers having matching colour with the existing false ceiling and suitable for deflection of 15/30/45 degree.

Item No:436 Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 41.3 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrig

Item No:437 Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 34.9 mm dia (OD) ) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrig

Item No:438 Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refri

Item No:439 Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrig

Item No:440 Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrig

Item No:441 Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrig

Item No:442 Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7 mm dia (OD) )for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrig

Item No:443 Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrig

Item No:444 Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 6.4 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrig

Item No:445 Supplying and erecting metal work in CRCA sheet with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2

Item No:446 Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, zcutting, drilling and welding complete erected at th

Item No:447 Providing Fully Compressive maintenance for items no.412 to 446, for 1st year

Item No:448 Providing Fully Compressive maintenance for items no. 412 to 446, for 2nd year

Item No:449 Providing Fully Compressive maintenance for items no. 412 to 446, for 3rd year

Item No:450 Supplying & installing, testing, baggage scanner.

Item No:451 Supplying, installing, testing commissioning boom barrier.

Item No:452 Supplying & erecting tensile barrier.

Item No:453 Supplying & erecting door frame.

Item No:454 Supplying & installing HD set top box.

Item No:455 Supplying, installing, testing router for wi-fi.

Item No:456 Supplying & erecting complete hardware rack etc and set up of system.

Item No:457 Supplying & installing co-axial copper cable low voltage grade RG-11 as per specification No. WG-TW

Item No:458 Fire Pump Room Equipment Supplying and installing air vessel of 300 mm dia 1.5 m in height M.S. tank installed inside pump house / on terrace complete as per specification no. FF-FFA/ACT.

Item No:459 Control Panel Supplying and erecting HMS PVC conduit 25 mm dia. with PVC accessories on wall / ceiling as per specification No. : WG-MA/CON.

Item No:460 Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at th

Item No:462 Supplying, ececting& terminating XLPE armoured cable 31/2 core 95 sq.mm. aluminium conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall / trusses / pole or laid in provided trench / pipe as per specifica.

Item No:463 Supplying, ececting& terminating XLPE armoured cable 31/2 core 70 sq.mm. aluminium conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall / trusses / pole or laid in provided trench / pipe as per specifica.

Item No:464 Supplying, erecting & terminating XLPE armoured cable 31/2 core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall / trusses / pole or laid in provided trench / pipe as per specifica.

Item No:465 Supplying, erecting & terminating XLPE armoured cable 31/2 core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall / trusses / pole or laid in provided trench / pipe as per specifica.

Item No:466 Supplying, erecting & terminating XLPE armoured cable 3 core 16 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall / trusses / pole or laid in provided trench / pipe as per specificat.

Item No:467 Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 200 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Item No:468 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 200 mm dia with necessary fittings complete as per specification no FF-PP

Item No:469 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 150 mm dia with necessary fitting complete as per specification no. FF-PP

Item No:470 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 100 mm dia with necessary fitting complete as per specification no. FF-PP

Item No:471 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 75/80 mm dia with necessary fitting complete as per specification no. FF-PP

Item No:472 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 50 mm dia with necessary fitting complete as per specification no. FF-PP

Item No:473 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 25 mm dia with necessary fitting complete as per specification no. FF-PP

Item No:474 Supplying and erecting cast iron double flange NRV of size 150 mm dia complete as per specification no. FF-VL/NRV.

Item No:475 Supplying and erecting cast iron double flange NRV of size 75/80 mm dia complete as per specification no. FF-VL/NRV.

Item No:476 Supplying & erecting cast iron double flange butterfly valve of size 150 mm dia complete as per specification no. FF-VL/BFV.

Item No:477 Supplying & erecting cast iron double flange butterfly valve of size 75/80 mm dia complete as per specification no. FF-VL/BFV

Item No:478 Supplying and installing pressure switch with 12/15 mm dia isolation valve, G.I. nipple, elbow etc. complete as per specification no. FF-FFA /PS

Item No:479 Supplying and installing pressure gauge of 100 mm dia., 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve and G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Item No:480 Supplying & erecting gun metal gate valve of size 25 mm dia complete as per specification no. FF-VL/GV.

Item No:481 Supplying and erecting cast iron foot valve ball type/flap type of size 150 mm dia with strainer for negative suction complete as per specification no. FF-VL/FV

Item No:482 INTERNAL WET RISER AND CUM DOWN COMER SYSTEM (Riser A & B) Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 150 mm dia with necessary fitting complete as per specification no. FF-PP

Item No:483 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 75/80 mm dia with necessary fitting complete as per specification no. FF-PP

Item No:484 Supplying & erecting cast iron double flange butterfly valve of size 150 mm dia. complete as per specification no. FF-VL/BFV.

Item No:485 Supplying and erecting gun metal double outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV.

Item No:486 Supplying fire fighting controlled percolation (C.P.) Hose pipe, 63 mm dia, 15 m in length, fitted with necessary accessories complete as per specification no. FF-FFA/CPH.

Item No:487 Supplying & erecting gun metal branch pipe of 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specification no. FF-FFA/NZ.

Item No:488 Supplying and installing wall mounting swinging Hose reel drum fitted with 19 mm dia. 30 m long high pressure polypropylene (Playhouse) fitted with necessary accessories complete as per specification no. FF-FFA/HV.

Item No:489 Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve (size 400 X 400 X 400 mm.) made from 16 SWG sheet and angle iron 25 mm.X 25 mm.X 4 mm. having front doors with viewing glass (8"X6") and locking arrangement with necessary.

Item No:490 Supplying and erecting 20/25 mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV.

Item No:491 EXTERNAL YARD HYDRANT SYSTEM Supplying and erecting G.I. Pipe above ground of 'C' class ERW of size 150 mm dia with necessary fittings complete as per specification no. EE-PP.

Item No:492 Supplying and erecting G.I. Pipe above ground of 'C' class ERW of size 75/80 mm dia with necessary fittings complete as per specification no. EE-PP.

Item No:493 Supplying & erecting cast iron double flange butterfly valve of size 150 mm dia. complete as per specification no. FF-VL/BFV.

Item No:494 Supplying and erecting stainless steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV.

Item No:495 Supplying fire fighting controlled percolation (C.P.) Hose pipe, 63 mm dia, 15m length, fitted with necessary accessories complete as per specification no. FF-FFA/CPH.

Item No:496 Supplying & erecting gun metal branch pipe of 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specification no. FF-FFA/NZ.

Item No:497 Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve (size 400 X 400 X 400 mm.) made from 16 SWG sheet and angle iron 25 mm.X 25 mm.X 4 mm. having front doors with viewing glass (8"X6") and locking arrangement with necessary.

Item No:498 Supplying and erecting noe no. brass orifice plate having 6 mm. thickness, 140 mm outer dia and required / proper diameter of inner hole at every single outlet hydrant valve as per specification no.FF-FFA/OP.

Item No:499 Supplying and erecting fire brigade header of 150 mm dia, for supplying water in fire tank complete as per specification no. FF-FA/FBC.

Item No:500 Supplying & erecting cast iron double flange butterfly valve of size 150 mm dia. complete as per specification no. FF-VL/BFV.

Item No:501 Supplying and erecting cast iron double flange NRV of size 150 mm dia complete as per specification no. FF-VL/NRV.

Item No:502 Supplying and erecting fire brigade header (Siamese connection) of 150 mm dia for supplying water to wet riser system complete as per specification no. FF-FFA/SMC.

Item No:503 SPRINKLER SYSTEM Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 150 mm dia with necessary fitting complete as per specification no. FF-PP

Item No:504 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 100 mm dia with necessary fitting complete as per specification no. FF-PP.

Item No:505 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 75/80 mm dia with necessary fitting complete as per specification no. FF-PP.

Item No:506 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 65 mm dia with necessary fitting complete as per specification no. FF-PP.

Item No:507 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 50 mm dia with necessary fitting complete as per specification no. FF-PP.

Item No:508 Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 25 mm dia with necessary fitting complete as per specification no. FF-PP.

Item No:509 Supplying erecting, testing and commissioning of 15 mm (1/2") dia. NBCM Body chrome finished quartzoid bulb sprinkler having 680 C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FF-SPR.

Item No:510 Supplying installation, testing & commissioning of installation control (Alarm) valve of cast iron abody and brass/bronze working parts comprising of water motor alarm, bronze seat clapper and clapper arm, hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of reqd, size, flanges, orifice plate, gasket ect. of size 150 mm dia as reqd. (NCSR Approved by C.E. PWD Electrical ....................

Item No:511 Supply Installation testing and commissioning of deluge valve complete with accessories, water motor alarm, bronze seat clapper and clapper arm, hydraulically driven mechanical gong bell to sound continuous alarm when system activates, pressure gauges, emergency releases, strainer, MS pipe of reqd. size, flanges, orifice, plate, gasket etc. wet pilot trim (electrically operated) of size 150 mm dia. NCSR Approved by C.E. PWD Electrical, Mumbai vide letter No. .... Date.

Item No:512 Supplying & erecting cast iron double flange butterfly valve of size 150 mm dia. complete as per specification no. FF-VL/BFV.

Item No:513 Supplying and installing pressure switch with 12/15 mm dia isolation valve, G.I. nipple, elbow etc. complete as per specification no. FF-FFA/PS.

Item No:514 Supplying & erecting cast iron double flange butterfly valve of size 100 mm dia complete as per specification no. FF-VL/BFV.

Item No:515 FIRE EXTINGUISHERS Providing Round bottom fire bucket of 9 Litres capacity as per IS : 2546 made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and red outside with FIRE Mark, on provided stand / wall hook complete.

Item No:516 Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 / 15683 complete erected with necessary clamp made from 50 X 6 mm. M.S. flat with nut & bolts grouted in wall complete.

Item No:517 Supplying and erecting ABC powder type fire extinguisher as per IS : 13849/15683 of 6 kg. capacity with necessary clamp for erection on wall.

Item No:518 Supplying and erecting ABC powder type fire extinguisher as per IS : 15683 of 9 kg. capacity with necessary clamp for erection on wall.

Item No:519 Supplying and commissioning of ceiling mounted type modular fire extinguishers 10 kg. (Electric Room)

PART - C :- Material Tests and Royalty charges

Material Tests

Item No:520 Carrying out Basic Test of Cement (as per sr.no.1) such as standard Consistency, Fineness, Specific Gravity, Setting Time (Initial & Final) Compressive Strength, Soundness in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed.

Item No:521 Carrying out basic tests on Sand (as per sr.no.10) for Fineness modulus,Silt and clay content , in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed.

Item No:522 Water Absorption, Moduls of Rupture (Set of 6 Tiles) for Ceramic /Vitrified Tiles (as per sr.no.16) , in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Item No:523 Flooring of Natural Stone (as per sr.no.15) (Kota,Marble, granite,Tandur.etc.)-Water absorption, Specific gravity), in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Item No:524 Carrying out basic tests on wood (as per sr.no.59)for density and moisture content, in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Item No:525 Carrying out basic tests on flush door (as per sr.no.60) for Knife Test, Adhesion Test, End Immersion Test., in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed.

Item No:526 Carrying out basic tests on PVC.Pipes (as per sr.no.70) for wt. per running meter, dia.of pipe and wall thickness of pipe., in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Item No:527 Concrete Mix Design (as per sr.no.8) , in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Item No:528 Carrying out basic tests on Concrete cubes (as per sr.no.19) for compressive strength, in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Item No:529 Carrying out basic tests on steel bars upto 16mm ((Set of 3 Bars) (as per sr.no.77), in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed.

Item No:530 Carrying out basic tests on steel Above 16 mm (Set of 3 Bars) (as per sr.no.78) (Tensile strength, %, Elongation, Yield Stress,Weight-Per Meter, Bend / Rebend Test, Proof Stress.), in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed.

Item No:531 Carrying out basic tests on Aggeregates (as per sr.no.2) for Water absorption, specific gravity. Impactvalue, crushing value, in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Item No:532 Carrying out basic tests on Aggeregates (as per sr.no.3,4) for Sieve Analysis,Abrasion value, in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Item No:533 Carrying out basic tests on Murrum (as per sr.no.29,32) for Sieve Analysis, C.B.R. Test ( Lab ) With compaction test.. in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed.

Item No:534 Carrying out basic tests on Bricks (as per sr.no.13) for Water Absorption (Set of 5 Bricks), Compressive Strength( Set of 5 Bricks), Efflorescence (Set of 5 Bricks) in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed

Item No:535 Carrying out basic tests on Plywood (as per sr.no.61) for Determination of Resistance to dry heat,Determination of Moisture Content,Determination of Density,Thickness of Plywood in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed.

Item No:536 Carrying out basic tests on Aluminium (as per sr.no.64)for Thickness, Mass Per Running meter in Govt. P.W.D. laboratory as per relevant B.I. Standards and submitting test results including all taxes, overheads and any other allied charges etc. completed.

Item No:537 Royalty charges for SAND to be reimbursed to the contractor after producing original receipt of payment made to the concern Govt. office as royalty charges for the material used for this work.

Item No:538 Royalty charges for OTHER (MURRUM & RUBBLE) to be reimbursed to the contractor after producing original receipt of payment made to the concern Govt. office as royalty charges for the material used for this work.

OMKAR CONSTRUCTION

M/s. DeltaTechs Construction Private Limited

Mahendra Realtors and Infrastructure Pvt Ltd

Shandar Interior Pvt. Ltd

Godrej and Boyce Mfg. Co. Ltd.