REPAIR/REPLACEMENT OF SANITARY FITTINGS, JOINERY, ROOF TREATMENT AND CLEANING OF WATER TANK AT VNC UNDER AGE B/R II IN GE (CENTRAL) BANGALORE

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing serviceable tiles to MES store and the rubbish/debris out side MD land complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors, plinth protection/path/pavings etc not exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position (other than ground floor) not otherwise specifically provided for (in roof/floor/padding etc) and removing debris outside MD land complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing debris outside MD landcomplete all as specified and directed

Taking up or down 15mm bore, steel tubing galvanised along with fittings or any other type of pipe complete all as directed.

Taking up or down 20mm bore, steel tubing galvanised along with fittings or any other type of pipe complete all as directed.

Taking up or down 25mm bore, steel tubing galvanised along with fittings or any other type of pipe complete all as directed.

Taking down chowkats or frame, not exceeding 1.5 Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description n.exc 1 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n. exc 2 Sqm each complete all as specified and directed.

Taking down shutters of any description n.exc 1 Sqm each and refixing shutter in the same opening including easing & adjusting complete all as specified and directed.

Taking down shutters,exc 1 Sqm but not exceeding 2.0 sqm in each and refixing shutter in the same opening including easing & adjusting complete all as specified and directed.

Resecuring or easing & adjusting without taking down shutters of any despription size exc 1 Sqm and not exc 2 Sqm each shutter all as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S & F in repair 110 mm dia, PVC rain water pipe single socket joint fixed to wall using MS holder bat, etc complete all as specified and directed.

S & F in repair PVC bend & shoes suitable for 110 mm dia PVC rain water pipe complete all as specified and directed.

M&L for 35 mm thick 2nd class hard wood factory made glazed/gauzed skeleton shutters for door, open rebated and prepared to receive glass, gauze etc (without sash bars), edges framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc; size of the members of shutters as specified in SSR Part- I, Section 8, clause 8.24(a) complete all as directed.

S&F 35mm thick Flush shutters, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified. MAKE : - Kitply / Green ply/ Century / Anchor/ Mysore Chip Board

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S & F box type steel windows/ventilators double side shutters ie glass and wire mesh shutter, including pressed steel frames made out of CRCA sheet of 80X60X1.25mm thick double rebated, shutters box type made out of CRCA sheet of 40X20X1.0mm thick, 12mm square guard bar/grill welded to steel frame, window shutters side hung, ventilator shutters top hung, box type hinges, aluminium die cast handles for glass shutters, iron flat type handles for mesh shutters, telescopic stays etc complete all as specified in TD drawing No TD/539 dated 09.02.2004 of Chief Engineer Chennai Zone and PCC filling into frame using plain cement concrete 1:2:4, type B0 etc complete all as specified and as directed . NOTE:- (i) Quoted rate under this item shall deemed to be inclusive of steel frame, both side steel shutters, guard bars/grills, handles, telescopic stays, beading/fillets for fixing glass/wire mesh including cost elements for fixing of glass & wire mesh and mearurement/ payment shall be considered as one unit by comprising all these elements. (ii) Glass and wire mesh shall be measured and paid as supply only separately under respective item.

S & F in repairs 50 mm size, butt hinges, medium weight, cold rolled mild steel bearing ISI marked complete all as specified and directed.

S & F in repairs 75 mm size, butt hinges, medium weight, cold rolled mild steel bearing ISI marked complete all as specified and directed.

S & F in repairs 100 mm size, butt hinges, medium weight, cold rolled mild steel bearing ISI marked complete all as specified and directed.

S & F 100 mm size, butt hinges, stainless steel with cadmium coated screws complete all as specified and directed.

S & F in repairs 200 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 150 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F in repairs 100 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 150 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F in repair 150 mm size, mild steel handles, oval type, stove enamelled black complete all as specified and directed.

S & F in repair 100 mm size, mild steel handles, oval type, stove enamelled black complete all as specified and directed.

S & F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F in repairs aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F in repair aluminium (extruded section body) door closer hydraulically regulated, designated No 2 universal aluminium (extruded section) body, suitable for aluminium door shutters of 701 to 850mm width and of weighing between 36 to 69KG. Make :- Everest/Prabhat/Amar/Godrej as approved by GE

S & F in repair door seal using 1.5mm thick strip of mild steel hard brush fixed to door bottom complete all as directed.

S & F in repair magnetic catcher with 8 mm dia steel ball and brass body with striking plate including letting in and fix complete.

S & F in repairs 100mm aluminium anodised, hasp and staple, safty type, with hinge pin, including bolt to hinge plate and fixed with screws complete all as directed.

S&F in repair aluminium anodised body and tounge floor door stopper with hard drawn steel spring, 150mm size fixed to door all as directed.

S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 4 mm thick, sheet glass, figured/ pin headed glass and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for stainless steel wire cloth 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples/wooden beading, complete all as specified and directed

S&F in repair stainless steel wire cloth 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples/wooden beading, complete all as specified and directed

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in base of flooring, etc and finished the surface fair to receive top layer screed bed complete all as specified and directed.

M & L for joint free non-skid, ceramic, coloured tiles, Grade B II(a), 8 to 10mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic joint free, coloured tiles, 450x350mm, Grade B III, 7 to 8 mm thick as in dado/vertical surface of wall/ skirting including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for granite stone slab, table rubbed and polished (of any type) 18 to 20mm thick, machine cut, as in steps, jambs, pillars, cooking platform and the like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed in cement mortar 1:4 & cutting, polishing complete all as specified and directed.

M & L for 40 mm thick, plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in floors laid in panels, finishing the surfaces even & smooth with using extra cement complete all as specified and directed.

S & F 3 mm thick, 38mm wide glass dividing strips and inserted in position to conform to design as required complete all as specified and directed.

M & L for plain cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) for door cill, lintels, steps, copings, apex stones, boundary pillars, paddings, with plain fair faces including chamfering, weatherings, throatings etc and setting in cement mortar necessary form work complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two layer (10mm + 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M & L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces as in ceilings (sunshed, chajja, fins etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

"Supply only" integral water proofing compound (ISI marked) complete all as specified and directed. (Make : Dr FIXIT/Fosroc/choksey)

M & L for removing plant/Uprooting of vegetation growth including roots on wall/roof/parapet/chajja/beam/near pipes etc and applying acid treatment after removing roots for preventing regrowth and making good disturbed surfaces/area in superficial area exc 150sq.cm but n.exc 400 sq.cm and averaging depth not exceeding 10 cm filling holes etc by using PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) or 10mm thick plastering in cement mortar 1:3 as required and finishing the surfaces to match with the existing surface complete all as specified and directed.

M & L for removing existing water proofing treatment in roof and disposing the same to out side of MD land/premises and roof treatment by rendering 10mm thick in CM 1:4 mixed with water proofing compound by weight of cement as per manufacturer's instruction, applying oil bound bitumen primer @ 1.5 Kg/Sqm and providing 3 mm thick APP membrane weighing not less than 3.6 kg/sqm reinforced with non woven polyester matt weighing not less than 180 gm /sqm having softening point not less than 140 centigrade, having tensile strength of 650N/sqm and 350 N/sqm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch application with minimum 10cm side overlap and 15cm end lap, applying a coat of blown grade hot bitumen 90/15 over the membrane @ 1.2 Kg /Sqm on top of membrane surface and then finished with solar reflective bituminious aluminium paint @ 0.10 Kg/Sqm complete all as specified and as directed. NOTE: - Water proofing compound shall be measured and paid separately under respective item.

M & L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

S & F 110 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall using MS holder bat, etc complete all as specified and directed.

S & F 75 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall, using MS holder bat etc complete all as specified and directed.

S&F PVC (SWR) junction single,(single T) 110 mm with access door complete all as specified and directed.

S&F PVC (SWR) junction single,(single T) 75 mm with access door complete all as specified and directed.

S&F PVC (SWR) branch piece single,(single Y) 110 mm dia equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) branch piece single,(single Y) 75 mm dia equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl suitable for 110 mm dia pipe.

S&F PVC (SWR) vent cowl suitable for 75 mm dia pipe.

Cutting chases for concealed water tubing or concealed conduit wiring, etc in brick wall/hardstanding/PCC work, cutting exc 10 cm but n.exc 20 cm girth, pinning in, making good to facings where required and pointing in cement mortar 1:3 ., and making good with cement mortar, complete all as specified and directed.

Supply, laying/fixing, connection and testing, 15mm bore, Steel water tubing, galvanised, 'medium grade' with all fittings and fixtures complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

Supply, laying/fixing, connection and testing, 20mm bore, Steel water tubing, galvanised, 'medium grade' with all fittings and fixtures complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

Supply, laying/fixing, connection and testing, 25mm bore, Steel water tubing, galvanised, 'medium grade' with all fittings and fixtures complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F in repair 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

S&F in repair Vitreous China Squatting Pan"Orissa pattern" size 580 mmx440 mm white with integral foot rest S or P trap etc. including 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long and 32mm dia flush pipe, S or P Trap & Provision of concrete bedding and making good to floor all as specified & directed by Engineer-in-charge. Make of Pan CERA Cat No S3010108 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S&F in repair Vitreous China Wash hand basin , white flat back size 550x400 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall, including provision of 32 mm waste coupling brass chromium plated suitable for wash hand basins & 32 mm dia LDPE PVC waste pipe, 45 cm long PVC connections including cutting hole and pinning in ends making good disturbed portion using cement mortar 1:3 complete all as specified & directed by Engineer-in-charge. Make of basin CERA Cat No S2040105 or equivelent of Parryware/Hindware/Prayag

S & F in repair 32mm dia, not exc 1.00 metre long, low density polyethelene (LDPE) pipes plain/corrugated type of pressure rating 6 Kgf/Sqcm with connecting brackets fixed to waste coupling for wash basin/urinals/sink etc complete all as directed.

S & F in repair 40mm dia, not exc 1.00 metre long, low density polyethelene (LDPE) pipes plain/corrugated type of pressure rating 6 Kgf/Sqcm with connecting brackets fixed to waste coupling for wash basin/urinals/sink etc complete all as directed.

S&F in repair stainless steel gratings, circular type, 125mm dia with waste hole fixed with white cement in existing traps complete all as directed.

S & F in repairs, 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe 32mm dia, float and handle including PVC connection pipe of 15mm dia, 600mm long, brackets complete all as specified and directed.

S & F in repairs PVC connection pipe with PTMT nuts, 450mm long. Make: CERA/Hindware/Parryware/PRAYAG

S & F in repairs PVC connection pipe with PTMT nuts, 600 mm long. Make: CERA/Hindware/Parryware/PRAYAG

S & F in repairs 32mm dia waste fittings, brass chromium plated fixed to WHB all as directed.

S & F in repairs 40mm dia waste fittings, brass chromium plated fixed to sink all as directed.

S & F in repair PVC syphon set with knob complete suitable for 10 litre capacity PVC flushing cistern complete all as directed.

S&F in Repair Pillar Tap 15 mm bore Chromium plated cast copper alloy with capstan heads, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe complete all as specified & directed by Engineer-in-charge.

S & F in repairs, PVC, water closet seat and cover, white/black closed pattern with recessed bottom, mild steel chromium plated or aluminium anodised hinging device complete all as specified and directed.

S & F in repair 15 mm bore, bib taps, cast copper alloy with crutch or butterfly handle, chromium plated, fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15 mm bore bib taps cast copper alloy chromium plated with capstan head screwed down to iron pipe, fancy type long nose type complete all as specified and directed

S & F in repair brass spindle suitable for 15 mm bib tap all as directed.

S & F in repair brass spindle suitable for 15 mm stop cock all as directed.

S & F in repair brass spindle suitable for 20 mm stop cock all as directed.

S & F 20 mm bore, gun metal gate valve, with iron wheel head, screwed both ends, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 25 mm bore, gun metal gate valve, with iron wheel head, screwed both ends, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repair 15 mm bore, stop cock, cast copper alloy with crutch or butterfly handle , screwed down, screwed both ends for iron pipe or for union/brass ferrule complete all as specified and directed.

S&F in repair 15 mm bore stop cock valve cast copper alloy chromium plated fancy type with long shank and cup, concealed type, screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO HT-F3001201 or equvelent of Make Hindware/Parryware/PRAYAG

S&F 15 mm bore angle valve cast copper alloy chromium plated fancy type with long shank and cup, concealed type, screwed down to iron pipe complete all as specified and directed. Make: PRAYAG or equvelent of Make Hindware/Parryware/Cera

S&F in repair 15 mm bore, any colour, PTMT, bib taps high pressure with capstan head screwed down to iron pipe complete all as specified and directed (Minimum weigh 90 gms). Make: PRAYAG Cat No 121 or equivelent of POLYTUFF

S&F in repair 25 mm dia stainless steel metalic coated curtain rod with ring brackets etc complete all as specified and directed

S&F in repair stainless steel curtain rod bracket suitable for 25mm dia curtain rod including wooden support etc complete all as specified and directed

S & F in repair shower rose PTMT with arms with or without swivel joint, 125mm size including fixing to iron pipes complete all as specified and directed. (Minimum wiegh 40 gms) (Make: PRAYAG or equivalent of Polytuff)

S & F in repair brass chromium plated shower rose with arms with or without swivel joint, 125mm size including fixing to iron pipes complete all as specified and directed. (Make: CERA Cat No F7020304CH or equivalent of Parryware /Hindware/Prayag)

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mmx203mm bowl size 405mm x 354mmx203mm (Make: Prayag Cat No 1239D or equivelent of Parryware /Hindware/Cera)

Dismantling of rotational moulded polyethylene water tank of capacity 250 Ltrs to 500 litres.

Dismantling of rotational moulded polyethylene water tank of capacity 1000 litres.

M&L for Disconnecting existing PVC tanks of any position or at any hight of any description,capacity exc 250 ltr but not exc 500 ltr, setting aside for cleaning (lowering if required) for repair, cleaning and removing all scale and dirt/dust from existing PVC tank and hoisting, reconnecting and refixing in position including inlet-outlet pipe at opening portion and at mouth etc complete all as specified and directed

M&L for Disconnecting existing PVC tanks of any position or at any hight of any description, capacity exc 500 ltr but not exc 1000 ltr, setting aside for cleaning (lowering if required) for repair, cleaning and removing all scale and dirt/dust from existing PVC tank and hoisting, reconnecting and refixing in position including inlet-outlet pipe at opening portion and at mouth etc complete all as specified and directed

S&F rotational moulded polyethylene water storage tanks 500 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm dia brass ball/float valve high pressure with polythene float and flynut, 25 mm water tank nipple/tank adoptor suitable for HDPE water tank complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm dia brass ball/float valve high pressure with polythene float and flynut, 25 mm water tank nipple/tank adoptor suitable for HDPE water tank complete all as specified and directed.

sri vasavi constructions