SPL REPAIR OF BLDG Nos. P-101, P-102 AND P-103 AT POKARAN MILITARY STATION UNDER AGE (I) POKARAN

Amount

B/R WORK Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

M&L for Non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L for Non-skid ceramic premium quality coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 15 mm thick screed in cement mortar (1:6) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by the Engineer-in-Charge.

All as per item No.3.00 her-in-before above but as in skirting over & including 10mm thick backing coat of CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mm in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of Stone slabs and tiles of any description or thickness in floors, walss, aprons etc laid bedded and pointed in any mortar removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and as directed by the Engineer-in-Charge.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar and laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10 mm thick backing coat in CM (1:4) complete all as specified and as directed by the Engineer-in-Charge.

M&L for Granite of black / green / imperial red (colour as approved by AGE) of any type machine cut as in shelves/steps/counter tops, 20 mm thick, set and jointed in cement slurry over & including screed of 15 mm thick / rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified and as directed by the Engineer-in-Charge. Note : Single piece should be used in steps/cills/jambs/shelves or equivalent as approved by AGE

M&L for Jaisalmer stone for wall cladding (of any type) 35-55 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of stone , exc .0.06 sqm but not exc 0.11 sqm ,including cutting and polishing types in wall including 20 mm thick CM 1:4 for laying Jaisalmer stone complete all as specified and as directed by the Engineer-in-Charge.

Complete removal of existing water proofing treatment incl bedding if any n exc. 50mm thick etc. on any type of roof, cleaning with wire brushers etc. and removal of debris out side MD land complete all as specified and as directed by the Engineer-in-Charge.

M&L for 40mm consolidated thickness as per the requirements PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate for levelling course complete all as specified and as directed by the Engineer-in-Charge.

M&L for 10mm thick screed plaster on roof for laying in CM 1:4 waterproofing treatment, with using WPC complete all as specified and as directed by the Engineer-in-Charge. Note :- WPC will be measured and paid separately under relevant item

Supply only integral Water proofing compound complete all as specified and as directed by the Engineer-in-Charge.

M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt not less than 150 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltr/Sqm by forced complete all as specified and as directed by the Engineer-in-Charge four course roof treatment consist of as under :- (i) Applying one coat of bituminous primer conforming to IS-3384 @0.3 Ltr per sqm, (ii) Laying of APP based membrane as specified thickness and weight, (iii) Applying one coat of aluminium paint @ 100 ml/sqm

Taking down cement plaster on stone walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed by the Engineer-in-Charge.

M & L for 15mm thick cement plastering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished fair & even without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for cement plastering 15mm thick in two layers (10mm and 5mm respectively) in cemet mortar 1:4 including mixing of liquid water proofing compound as per manufacturer's instructions on brick work or concrete surfaces or in chajjas/parapet walls etc finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note : WPC will be measured and paid separately under relevant item.

M&L for 5mm thick , plaster in cement mortar (1:3) on ceiling surfaces and finishing the surface even and Smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bond distemper over one coat of putty including one coat of primer complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistance primer complete all as specified and as directed by the Engineer-in-Charge.

Taking down door shutter area exc 1 sqm but n exc 2 sqm each and removing to store complete all as specified and as directed by the Engineer-in-Charge.

S&F Spray duco painted Pressed steel frames made of MS sheet of 1.20mm thickness of size 105 x 60 mm for doors with single or double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts, PCC 1:3:6 type C-0 in fillinng inside frame & hold fasts etc complete all as specified and as directed by the Engineer-in-Charge. Note :- Distrubed protion of existing floor/ wall/ tile/ plaster etc during fixing of chowkhats shall be repaired to match with exisitng finish. Cost of the same will be included in this items.

S&F Factory made ISI marked flush door shutters 35mm thick, BWP conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 2nd class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters complete all as specified and as directed by the Engineer-in-Charge and including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

Taking down door/windows/ventilators chowket or frame incl shutter area n exc 1.50 sqm Each and removing to store complete all as specified and as directed by the Engineer-in-Charge.

S&F solid PVC door frames of size 50x47mm made out of 5mm plain colour PVC sheet supplying and fixing in opening as per specification and drawing shown in SSR complete all as specified and as directed by the Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification including the following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf

Taking down chowkhats or frames door/windows/ventilators (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and as directed by the Engineer-in-Charge.

S&F Spray duco painted Pressed steel frames made of MS sheet of 1.20mm thickness of size 125 x 60 mm for doors with single or double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts, PCC 1:3:6 type C-0 in fillinng inside frame & hold fasts etc complete all as specified and as directed by the Engineer-in-Charge. Note :- Distrubed protion of existing floor/ wall/ tile/ plaster etc during fixing of chowkhats shall be repaired to match with exisitng finish. Cost of the same will be included in this items.

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-I section 8 clause 8.20 (a) kiln seasoned and chemically pressure treated all as specifeid including stainless steel 304 grade wire cloth ( 0.36mm nominal dia of wire and average width of aperture 1.40 mm ) and including supply and fixing following items:- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x3000mm - 1 nos per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf

S&F 35mm thick, IInd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete including S & F following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

M&L for preparation of new wooden surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint, first quality, over a coat of pink primer on wooden surface complete all as specified and as directed by the Engineer-in-Charge.

M&L for Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410-W (Gde E-250) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

S&F Factory made Box Type steel window with side hung shutters including projecting type hinges with steel handle, and steel peg stay , complete without glazing bars, dovetailed or complete as shown in Drawing No. CEJZ/TD/22 sh 1/1 to 1/3, and complete all as specified and as directed by the Engineer-in-Charge.

S&F Factory made Box Type steel window with side hung shutters including projecting type hinges with steel handle, and steel peg stay , complete with glazing bars, dovetailed or complete as shown in Drawing No. CEJZ/TD/22 sh 1/1 to 1/3, and complete all as specified and as directed by the Engineer-in-Charge.

S&F Factory made Box Type steel ventilators fixed type, incl with one shop coat of primer,complete as shown in Drawing No. CEJZ/TD/24 sh 1/1 to 1/3, and complete all as specified and as directed by the Engineer-in-Charge.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290.Gde-E-165 complete all as specified and as directed by the Engineer-in-Charge.

S&F floor door stopper of aluminium 150mm size complete all as specified and as directed by the Engineer-in-Charge.

S&F stainless steel wire 0.36mm nominal dia of wire and average width of aparture 1.40mm complete all as specified and as directed by the Engineer-in-Charge.

S&F 4mm thick plain sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 sqn in each pane complete all as specified and as directed by the Engineer-in-Charge.

S&F 4mm thick figured glass, pin headed type and glazing with oil putty in square n exc 0.50 sqn in each pane complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparing new untreated steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide prime complete all as specified and as directed by the Engineer-in-Charge.

M&L for 12mm thick,veneered decorative plywood, grade-1 (with BWR resin) with decorate face veneers on both faces; fixed with screws to timber frame work including taking down of old cup board etc complete all as specified and as directed by the Engineer-in-Charge.

S&F 2nd class hard wood Plain fillets, square, rectangular or triangular in section, wrought, secured with nails or brads, sectional area Exc 3 & n. exc6 sq. Cm complete all as specified and as directed by the Engineer-in-Charge.

S&F Prelaminated particle board,interior grade, prelaminated both side 18/19 mm thick with decorative choice lamination , fixed with screws to timber frame work complete all as specified and as directed by the Engineer-in-Charge.

S&F 125mm long, Hasp and staple, allumuniun anodised, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and as directed by the Engineer-in-Charge.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps 40mm ( when open) complete all as specified and as directed by the Engineer-in-Charge.

S&F 40 mm knobs of brass, polished fixed with nut screw &washer bright finished complete all as specified and as directed by the Engineer-in-Charge.

S&F ball catcher with 8 mm dia steel ball and brass body and skirting plate including leting in and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F 100 mm long Extruded aluminium alloy handles, fabricated type. anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair aluminium anodised, (fancy type) curtain rod, 20mm dia, complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair bracket aluminium anodised, (fancy type) for 20 mm dia tubular curtain rod(for item above) complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete unreinforced in ground floors and pavings not exc 15cm thickness below or above ground level etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

Dismantling of water tanks and removing to store capacity of tank exc 250 and n exc 500 ltr. complete all as specified and as directed by the Engineer-in-Charge.

S&F 500 ltr capacity rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part-I, complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair Ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to dia of pipe 20mm as complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 15 mm bore to walls, ceiling etc. complete all as specified and as directed by the Engineer-in-Charge.

All as per item No.59.00 here in before above but 20mm dia pipe complete all as specified and as directed by the Engineer-in-Charge.

Refixing old steel tubing 15 mm and connections in new or old position (Walls, ceiling,floors, etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F Medium grade GI tubing 15 mm bore with all fittings , to walls, ceiling or laid in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

All as per item No.62.00 here in before above but in 20mm bore pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed in repairs to 15 mm bore pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed in repairs to 20 mm bore pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs for stop cock copper alloy but fancy type and chrominum plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron/pipe or for union and fixed 15 mm bore complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs bib taps cast cipper alloy chromoum plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F Viterious china white wash hand basin of size 580mm x 450mm including 15 mm pillar cock cast copper alloy CP, 15mm cast copper stop valve, 32 mm brase CP waste fitting, PVC waste pipe 32 mm dia & 15 mm PTMT connection pipe 450 mm long, complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs towel rail 600 mm long of Brass C.P 'D' type fixed with and including chromium plated brass screws and wooden /plastic cheatscomplete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs stainless steel sink with drainage board , made out of 1.00mm thick sheet for kitchen or laboratory with plug,washers, waste pipe, cast irn cantilever bracket of overall size 915x460mm bowl size 410x330x160mm complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair CP Shower rose 125mm size with swivel joint including fixing sted pipe for union complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC connections 15 mm size with PTMT nuts to length 600 mm complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC flushing cistarn 10 ltrs capacity ISI marked incl PVC damtake pipe PVC 450mm inlet etc complete all as specified and as directed by the Engineer-in-Charge.

Cutting holes in to or through in brick or stone walls built in cement mortar and making good in CM 1:3 or cement concrete 1:2:4 type B1 as required, exc 150sqcm & n exc 400 sqcm complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of cast iron RCC, AC or PVC pipe jointed in CM any dia bore complete all as specified and as directed by the Engineer-in-Charge.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm dia out let complete all as specified and as directed by the Engineer-in-Charge.

PVC (SWR) multi floor trap with grating including jointing with solvent cement 75 mm dia out let complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) pipes of 110 mm dia, single socketed fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) pipes of 75 mm dia, single socket fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

S&F 100 bore of pipe stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) bends with access door of 110 mm dia, any radius complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC(SWR) bends with access door of 75 mm dia, any radius complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) bends of 110 mm dia, any radius complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) bends of 75mm dia, any radius complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) vent cowl, 100 mm dia complete all as specified and as directed by the Engineer-in-Charge.

M&L for brushing neat cement slurry with 3.0 kg of cement per sq. Metre complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 15 mm thick in cement motor 1:3 with using water proofing compound surface finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note :- water proofing compound will be measured and paid separately under relevant item

M&L for applying coat of industrial bitumen 85/25 at the rate of 1.20 kg/sqm including cleaning the existing plaster/concrete surfaces of sunken portion complete all as specified and as directed by the Engineer-in-Charge.

M&L for P C C 1:5:10 type E-2 (40mm graded stone aggregate) as in filling under sunken floor complete all as specified and as directed by the Engineer-in-Charge.

Demoliton of RCC Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similars complete all as specified and as directed by the Engineer-in-Charge.

M & L RCC ( M-25 ) 20mm grade aggregate as in Slab, chajjas & parapets complete all as specified and as directed by the Engineer-in-Charge.

M&L form work to sides and soffits of Slab, chajjas & parapets complete all as specified and as directed by the Engineer-in-Charge.

Providing and placing in position microconcrete which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion obtained from approved manufacturer of thermoex chemical as per speciification and complete all as specified and as directed by the Engineer-in-Charge. Note :- payment under this item shall be made only after wet curing bas been done and surface has been satisfactory evaluated by sounding/tapping with blunt metal instrument

M&L for TMT bars 10mm dia & over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge.

All as per srl item No.97.00 here-in-before above but 6mm to 8mm dia complete all as specified and as directed by the Engineer-in-Charge.

Demolition of brick masonry or stone masonary built in cement mortar complete all as specified and as directed by the Engineer-in-Charge.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified and as directed by the Engineer-in-Charge.

All as per srl item No.101.00 here-in-before above but except stone. NOTE : Old serviceable stones retrieved vide Sl Item No. 99.00 shall be reused.

Dismantling of Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer) complete all as specified and as directed by the Engineer-in-Charge.

M&L for 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub bases complete all as specified and as directed by the Engineer-in-Charge.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed by the Engineer-in-Charge.

M&L for providing cement concrete 1:2:4 type B-1 (12.5 mm graded aggregate) as in kerbs of mud stops, rounded or chamfered on edges complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and as directed by the Engineer-in-Charge.

S&F Pre-painted galvalume sheet aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of RCC/steel posts/struts any section , including taking out embedded in concrete, brick work or stone masonry including taking out embedded portion etc and making to disturbed ground complete all as specified and as directed by the Engineer-in-Charge.

Excavation in post holes (or similar holes) each n exc 0.5cu .m,getting out in soft/loose soil, returning,filling in and ramming earth or broken rubble mixed with earth around,in layer not exceeding 25 cm,watering and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and as directed by the Engineer-in-Charge.

M&L for PCC 1:3:6 Type C-2 (using 40 mm graded stone aggregate) in walls or retaining walls, any thickness size of shape including,pilasters, boundary pillars and posts (including post and bases) complete all as specified and as directed by the Engineer-in-Charge.

Dismantling structural steel works including steel work in doors, gates, framed truss etc complete all as specified and as directed by the Engineer-in-Charge.

S&F for MS work confirming to Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 etc complete all as specified and as directed by the Engineer-in-Charge.

S&F roof trusses (framed), sunshade frames, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe-410-W(Gde-E-250) complete all as specified and as directed by the Engineer-in-Charge.

Demolition of plain cement concrete (Un-reinforced) in benching and surface channels,bedding etc. below or above ground level complete all as specified and as directed by the Engineer-in-Charge.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar as in concrete bed, haunching set in cement mortar of 150 mm dia complete all as specified and as directed by the Engineer-in-Charge.

Excavation in trenches n.exc 1.5m deep and n.exc 1.5m wide in manholes,etc. and getting out any type of soil complete all as specified and as directed by the Engineer-in-Charge.

M&L for plain cement concrete 1:4:8 Type D2 using 40mm graded aggregate as in foundation, filling in mass concrete for manholes & drains complete all as specified and as directed by the Engineer-in-Charge.

M&L for plain cement concrete 1:2:4 Type B1 using 20 mm graded aggregate as in benching and surface channel of manholes complete all as specified and as directed by the Engineer-in-Charge.

M&L for plain cement concrete 1:3:6 Type C1 using 20mm graded aggregate as in coping including necessary form work etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for squared rubble walling, brought upto coursed Jodhpur type well bonded bedded laid dry complete all as specified and directed by Engineer-in-Charge.

All as per Item No. 121.00 here-in-before above but except stone complete all as specified and directed by Engineer-in-Charge. NOTE : Old serviceable stones retrieved vide Sl Item No. 99.00 shall be reused.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses complete all as specified and directed by Engineer-in-Charge.

M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement incl, forms mould, mi-tred/stopped ends etc. complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 15mm thick in CM 1:4 on stone masonary sufaces on wall including finished even and smooth using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for reinforced concrete NP-2 drain pipes 200 mm Dia pipes confirming to IS laid in trenches and jointed in CM 1:2 complete all as specified and as directed by the Engineer-in-Charge.

M&L for concrete bed to drain pipes including packing under haunching against the sides of pipe after they are laid and tested; in cement concrete 1:4:8 type D-2 for 150mm dia pipe complete all as specified and as directed by the Engineer-in-Charge.

M&L for reinforced concrete NP-2 drain pipes 200 mm Dia pipes confirming to IS laid in trenches and jointed in CM 1:2 complete all as specified and as directed by the Engineer-in-Charge.

M&L for concrete bed to drain pipes including packing under haunching against the sides of pipe after they are laid and tested; in cement concrete 1:4:8 type D-2 for 200mm dia pipe complete all as specified and as directed by the Engineer-in-Charge.

M&L for cutting in to existing manhole for connectiing new drain 150 mm bore , making good to pipe & rendering cutting out existing benching for & forming branch channel in cement concrete (1:2:4) type B1 smooth finished & reforming benching as requierd complete all as specified and as directed by the Engineer-in-Charge.

Returning filling in soil including spreading, levelling and well ramming in layers n.exc 25cm thick in layer etc complete all as specified and as directed by the Engineer-in-Charge.

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M&L for jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted, set, jointed and grouted in CM 1:3 complete all as specified and directed by Engineer-in-Charge.

M&L for 5cm thick Sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc.n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

M&L for providing cement concrete 1:2:4 type B-1 (20 mm graded aggregate) as in cover slabs (for manhole) set in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

E&M WORK Taking down carefully existing point wiring of any description light, fan,sockets,bells etc) complete including fittings such as terminal boxes, switches, sockets, ceiling rose, lamp holders, brackets sketch fittings, pendants, fan regulartors and making good the disturbed surfaces, walls, floors etc. complete all as specified and directed by engineer-in-charge.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site or carrying to the store (To be measured only when found serviceable in all respects complete for reuse) complete all as specified and directed by engineer-in-charge.

M&L for point wiring complete with 1.5 Sqmm single core PVC insulated cable 1100 Volts grade multistranded copper conductor drawn through in PVC Casing and Capping on surface stone/brick, masonry walls, roofs floors etc including MS terminal boxes fabricaterd out of 1.12mm thick MS sheet sunk type / surface type and laminated top sheet of 2mm thick for housing switches sockets, regulators etc including provn of 1.5 sqmm dia copper conductor for earth wire connected to common dolly for One light point / Fan point / Exhuast Fan point controlled by one 5 Amps One way switch complete all as specified and directed by engineer-in-charge.

All as per Item No. 139.00 here-in-before but for one 3 pin 5/6 Amps switch socket outlet on same board

All as per Item No. 139.00 here-in-before but for one 3 pin 5/6 Amps switch socket outlet on independent board

All as per Item No. 139.00 here-in-before but for wiring with 4.0 Sq mm and 4.0 sqmm for earth continuity for 3 pin 15/16 Amps switch socket combination

S&F switch piano flush type single pole one way 5 Amps complete all as specified and directed by engineer-in-charge.

S&F switch socket combination outlet, multipurpose, 2 pin 5 amps/3 pin 5 amps controled by one switch 5 amps, flush type complete all as specified and directed by engineer-in-charge.

S&F universal switch socket combination outlet with shutter, 5/15 amps controlled by one switch 15 amps, flush type complete all as specified and directed by engineer-in-charge.

S&F ceiling fan regulator Stepped type, 120 W-2 module AC 240 V complete all as specified and directed by engineer-in-charge.

S&F lamp holder insulated body with back plate suitable for battern fittings complete all as specified and directed by engineer-in-charge.

S&F ceiling rose surface bakelite 65 x 50 mm 2/3 terminais complete all as specified and directed by engineer-in-charge.

S&F Sheet Modular metal enclosure DB TPN 415 Volts 4 Way single door type with 200 Amps busbar for fixing of MCBs complete all as specified and directed by engineer-in-charge.

S&F Sheet Modular metal enclosure DB SPN 240 Volts 8 Way single door type with 200 Amps busbar for fixing of MCBs complete all as specified and directed by engineer-in-charge.

S&F connection testing and commissioning of TPN 100Amp 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete all as specified and directed by engineer-in-charge.

S&F connection testing and commissioning of SPN 32Amps rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete all as specified and directed by engineer-in-charge.

All as per Item No. 152.00 here in before above but for MCB SP 5 to 32 Amps

S&F LED Lamp Retro fit type 9 watts 230 V complete all as specified and directed by engineer-in-charge.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge o the plate not less1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts nuts, check nuts and washers of galvanized iron of steel all as shown in electrical plate No.5 connected to earthing test point incl necessary earth work, excavation PCC 1:3:6 type CI using 20mm graded stone aggregate for earth chamber provn of PCC cover 40 mm thick 1:2:4 mm type B1 funnel with water Pipe, GI pipe, 15mm dia medium grade protection pipe, GI earth lead complete all as specified and directed by engineer-in-charge.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by engineer-in-charge.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by engineer-in-charge.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by engineer-in-charge.

S&F in replacement service bracket for street light fitting made out of suitable dia bore light grade GI pipe of length 1.5 mtr long (approx) bend to shape 115 degree and fix to pole for fixing of street light fitting on pole/wall etc fixed with 2 Nos 32x 6 mm GI clamp, Nut, bolts, washer etc complete all as specified and directed by engineer-in-charge.

Supply and laying sub main wiring with two runs of 4 Sq mm single core PVC insulated unsheathed cable upto and including 1100 volts grade with multistranded copper conductor drawn through in PVC Casing and Capping on surface walls, floors etc including one run of 4.0 Sqmm PVC insulated copper conductor for earth continuity wire including taking down old unserviceable submain wiring complete all as specified and directed by engineer-in-charge. Note : Two runs of copper conductor and one run of earth wire will be measured and paid as one unit only

M/s. Shiva Engineers (BID ID -3341446)

SHIVA CONSTRUCTION COMPANY (BID ID -3341994)

M/s PRABHU DAN DETHA AND COMPANY (BID ID -3341793)

B B BUILDERS (BID ID -3341761)

S AND A ENGINEERS CONSTRUCTION CO (BID ID -3341574)