GE(S)/M-59/2023-24

Amount

Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for use and waste of form work to sides of flat, rough finished surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical to batter complete all as specified and directed.

M&L for use and waste of form work to sides of square, rectangular or polygonal, rough finished surfaces of concrete of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for use and waste of form work to soffits of flat, rough finished surfaces of concrete of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick(Horizontal or sloping) complete all as specified and directed.

M&L for use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10 cm but n. exc. 20 cm wide, rough finished surfaces of concrete complete all as specified and directed.

M&L for use and waste of form work to sides and soffits of flat, rough finished surfaces of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs and mass concrete complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in beams, cantilevers, bressumers, lintels, shelves complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies and in shelves and the like complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 8mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:6) complete all as specified and directed.

M&L for brick work with fly ash bricks, old size as in half brick thick walls straight or curved on plan exc 6 mtr mean radius built in CM (1:4) complete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge n. exc. 63 mm, deposited, spread and leveled in layers n. exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick Cement concrete 1:3:6 type C-1, using 20mm graded stone aggregate as in plinth protection and pavings laid in slope finished even and fair incl making joints at every 2.5 m and at corners filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified and directed

M&L for 75mm thick PCC 1:4:8: type D-2 (using 40 mm graded stone aggregate) as in floor/sub base complete all as specified and directed.

M&L for 20 mm thick screed bed or bedding layer in CM 1:6 for laying floors finishes complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed (joint free) in neat cement slurry and pointed in white coloured cement to match complete all as specified and directed Note : Screed bed shall be measured and paid for separately.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick, area of each tile exc. 0.11 sqm and n. exc. 0.18 sqm, in floors etc set and jointed (joint free) in neat cement slurry and pointed in white coloured cement to match complete all as specified and directed. Note : Screed bed shall be measured and paid for separately.

M&L for 10mm thick cement screed for skirtig/dado in cement mortar 1:4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for glazed ceramic coloured tiles 450mmx300mmx7mm in vertical surface, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as spd & directed. Note : cement screed shall be measured and paid for separately.

M&L for 10 mm thick rendering in cement mortar 1:6 on brick or concrete surfaces of walls, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in two layers, 1st layer of 5mm thick mixed with WPC @ 200 ml/50 kg of cement and 2nd layer 10mm thick in cement mortar 1:4 on brick or concrete surfaces of walls, surface finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid for separately as supply only.

M&L for 5 mm thick rendering in cement mortar 1:3 on brick or concrete surfaces of ceilings, finished even and smooth without using extra cement all as specified and directed.

Preparation of newly plastered surfaces of external walls and applying two coats of cement base paint including curing before and after, including a coat of alkali-resistant primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls, applying 1mm thick wall care putty, making the surface even & smooth and applying two coats of oil emulsion distemper complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed

S&F Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick M S sheet tube factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes only shall be measured and paid separately) with steel handle and steel peg stay dovetailed or welded incl 2 Nos. tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg, welded to F I frame work, including other fittings; hinges, handles, tarred hold fasts fixed in PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and directed.

S&F 3 mm sheet glass, ordinary quality in square or rectangle n. exc 0.5 sqm each pane fixed to framed work (for windows) complete all as specified.

S&F 3 mm figured glass, pinhead type in squares n exc 0.5 sqm each pane fixed to aluminium framed work (venilators) complete all as specified.

S&F stainnless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or rubber/aluminium beads complete all as specified and directed.

S&F factory made pressed steel frame of size 125x60mm, made out of MS sheet 1.25mm thick for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling hollow back chowkhats with cement concrete 1:3:6 type C-0 (using 12.5 mm graded aggregate stone aggregate) incl application of two coats of synthentic enamel paint on exposed surfaces of steel surfaces complete all as spoecified and directed.

S&F factory made 35mm thick, 2nd class hard wood plain framed, panelled shutters (two panels) with lock rail and panel of 9mm thick BWP commercial ply. The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, fitted to chowkhats including preparation of surfaces of shutter and application of two coats of synthetic enamel paint over a coat of pink primer, etc complete all as specified and directed.

M&L 35 mm thick wire guazed and skeleton shutters (1st class softwood) , open rebated and prepared to receive wire cloth, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing wire cloth, etc.; sizes of me-mbers of shutters as specified in fitted to chowkats including preparation of surfaces of shutter and application of two coats of synthetic enamel paint over a coat of pink primer, etc complete all as specified and directed.

S&F 300mm mild steel, ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed.

M&L for preparation of new wooden or wood based surfaces over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer on exposed surfaces complete all as specified and directed.

S&F 20 mm bore mild steel drapery rods with 1 mm thick PVC wood grain coating including brackets and knobs fixing above windows and doors openings for hanging curtains complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composit) solid door/windows/ceosetory windows & other frames/chowkhat of size 45 x 70mm comprising of vigin PVC polymer of K value 58-60 (suspension grade), calcium carbonate & natural fibres (wood powder/rice husk/ weat husk) and non additives (maximum toxicity index of 12 for 100gms) fabricated with mitre joints after applying PVC solvent cement and screwed with fully body threaded star headed SS screws having minimum frame density of 750kg/cum, screw withdrwal strenght of 2200N (face), 1100n (edge), minimum compressive strength 58 N/Sqmm , modulas of elasticity 900N/sqmm and resistence to spread of flame of Class A category with property of being termite /borer proof, water/moisture proof and fire retrdant and fixed position MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note:- MS hold fasts/lugs or SS fasteners shall bemeasured and paid separately

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing in SSR-2020 Part-II.

S&F 200 mm long barrel tower bolt, aluminium anodised, of extruded section and fixed complete all as specified and directed.

S&F 150 mm long extruded aluminium alloy handle, fabricated type, anodised complete all as specified and directed.

S&F 100 mm long butt hinge, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white of bowl size 550mm x 400mm flat back, including waste pipe, brackets and cutting for and pinning in ends of & incl new brackets or errecting stand and 32 mm dia PVC waste pipe including waste coupling 32mm size full thread, complete all as specified and directed.

S&F 15mm bore pillar cock fancy type brass chromium plated, screwed down high pressure with or without letters hot or cold with long screwed shank and fly nuts screwed for iron pipe complete all as specified & directed.

S&F 15mm bore bib tap brass chromium plated, with flange, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F Stop valve/Angle valve (ISI Marked), fancy type chromium plated cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore ccomplete all as specified and as directed.

S&F Vitreous china wash down water closet pan (pedestal pattern), white, complete including fixing to trap, Incl Supply and fixing of PVC seat and seat cover complete all as specified and as directed.

S&F Chromium plated Jet Spray (with 1.50 mtr flexible chromium plated tube) fixed to EWC and connected to angular Stop Cock complete all as specified and directed.

S&F PVC flushing cistern 10 ltr capacity incl PVC connection, inlet and and outlet connections, brackets, PVC flush pipe with bend 32 mm dia of suitable length including making necessary connections to water supply pipe line and jointing to WC complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F Vitreous China Urinal of size 465 X 355 X 265 mm white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with brackets, flush pipe, grating and union for discharge pipe fixed incl supply and fixing of CP coupling, waste pipe, water spreader and all necessary fittings, complete all as specified and directed.

S&F Stainless steel Grating doom 100mm dia with waste hole complete fixing in floors complete all as specified and directed. .

S&F glass shelf assembly consisting of 5.5 mm thick sheet glass 12 cm wide with CP brackets guard and railing 60 cm long, complete all as specified and directed.

M&L for cutting existing GI pipe 25 mm bore dia for addn/altn, branch connection and inserting of 'Tee' of size 25mm X 25mm X 20mm complete including necessary excavation & earth work complete all as specified and directed. Note: cost of 25mm X 25mm X 20 mm bore dia Tee and earth work are included in the unit quoted rate.

Supply, laying & jointing steel tubes, 15 mm bore 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors and testing complete all as specified & directed.

Supply, laying & jointing steel tubes, 20 mm bore 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors and testing complete all as specified & directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed with 20 mm dia pipe complete all as specified and directed.

S&F Stop valve cast copper alloy (ISI Marked) fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia complete all as specified and directed.

S&F PTMT Shower rose with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F Cast iron floor trap 75 mm with grating including jointing to waste pipe fixed in and including cement concrete type B-1 (1:2:4) complete all as specified and directed.

Supply, laying and jointing 100 mm bore Cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, with cement joints, fixed on walls with clamps complete all as specified and directed. Note : Fittings shall be measured and paid for separately.

S&F 100 mm dia cast iron bend (sand cast) with oval access door and jointed with neat cement paste complete all as specified and directed.

S&F 75 mm dia cast iron bend (sand cast) with oval access door and jointed with neat cement paste complete all as specified and directed.

Supply, laying and jointing 75 mm bore cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, with cement joints, fixed on walls with clamps complete all as specified and directed. Note : Fittings shall be measured and paid for separately.

S&F 100 mm cast iron cowls jointed with neat cement paste complete all as specified and directed.

S&F Stack clamp made out of 50 mm x 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays fixed to wall or roof for 100 mm dia CI pipe.

S&F Rotational moulded polyethlene water storage tanks of capacity 1000 litres three layers (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete including 20mm dia ball PVC valve high pressure with polythene float complete all as specified & directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface using chloropyriphos chemical conforming to IS 8944-2005 complete all as specified and directed.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) using chloropyriphos chemical conforming to IS 8944-2005 complete all as specified and directed.

M&L for treating the soil along the external perimeter of building at the rate of 2.25 litres of emulsion per meter of the perimeter wall using chloropyriphos chemical conforming to IS 8944-2005 complete all as specified and directed.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area using chloropyriphos chemical conforming to IS 8944-2005 complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:4 on concrete surfaces on top of roof slab mixed with 200ml of liquid water proofing compound per 50kg of cement and surface finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid for separately as supply only.

M&L for APP modified roof treatment over existing non-accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly. (b) Applying oil based bitumen primer with a density 0.87-0.89 Kg per litre at 25 degree centigrade manufactured by the same agency as that of APP on prepared surfaces @ 0.30 litre/Sqm. (c) Laying not less than 3.6mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. (d) Top of membrane shall be provided with solar reflective bituminous aluminum paint @ 0.10 KG / Sqm as prescribed by manufacturer of membrane. (e) APP Membrane shall be stick inside parapet where available by chase cutting and sealed with PCC 1:2:4, type B-0. (f) Top of membrane shall be provided with solar reflective bituminous aluminium paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane.

Supply only liquid water proofing compound complete all as specified and directed.

Returning filling in including spreading, leveling and well ramming, in layers not exceeding 25 cm each layer of any kind of soil complete all as specified and directed.

Removing surplus excavated material to a distance not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested in cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregates), complete all as specified and directed.

M&L for SGSW drain pipes grade 'A' of size 150 mm internal bore dia laid to slope in trenches, jointed in cement mortar (1:1) and tested complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exc 6 mtr mean radius built in cement mortar (1:4) complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar 1:3 mixed with liquid water proofing compound @ 0.200 ltr per 50 kg of cement, on stone masonary surfaces or concrete surfaces (internal), finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid for separately as supply only.

M&L for precast cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar 1:4, complete all as specified and directed.

M&L for mild steel work as in handles of cover slab and rungs and similar small articles confirming to Fe-290 grade E-165 complete all as specified and directed.

Removing surplus excavated material to a distance exceeding 250 mtrs but not exceeding 500 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for Septic tank 25 Users designed to carry sewage and sullage water, complete including excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls, Base Slab, Baffle walls and Roof Slab and beams etc including Vent shaft, manhole openings with cover and making connection etc., of effective depth 1.5 metre and overall depth of 3 metre complete all as described and shown on Drg No CEPZ/C-TD/013 /13 dated 11 -09- 2013 sheet 1/5 to 5/5.

M&L for Soakage wells of size 1.80m dia x 3.00 m depth including excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed brick masonry in CM 1:4 with sub class B bricks, top ring of RCC, M-25 design mix concrete including intercepting chamber and screen chamber made of Brick masonary in CM 1:4, RCC cover slab in M-25 design mix & SFRC MH cover incl interconnecting pipes of RCC/DWC complete filled with brick bats complete all as shown on Drg No CEPZ/C-TD/013 /13 dated 11 -09- 2013 sheet 1/5 to 5/5 .

Excavating in post holes (or similar holes) each n exc 0.5 cum in any type of soil getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

M&L for mild steel fencing posts/struts including embeding in concrete and screwing etc. including securing bolts; including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:4) complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, haunching, benching, kerbs , mud stops, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for 18 to 20 mm thick granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills cooking platforms & like including pointing with white cement (1:2) using marble dust with admixture of pigment to match shade of granite complete all as specified and directed. Note: Screed bed shall be measured & paid for separately.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for anging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

M&L for preparation of new surfaces of steel or iron of any discription exc 10cm width or girth and providing two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

M&L for coloured machine pressed precast rubber moulded concrete interlocking (Grey/red/yellow) paver block 60 mm thick, M-35 grade of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 complete all as specified and directed.

M&L for dry clean fine river sand as in sand filling under paver blocks including punning down of sand layer, watering & levelling complete all as specified and directed. Note :- Punned thickness shall only be measured and paid.

M&L for Septic tank 10 Users designed to carry sewage and sullage water, complete including excavation in any type of soil, PCC 1:4:8 under foundation, RCC M-30 Design Mix in Walls, Base Slab, Baffle walls and Roof Slab and beams etc including Vent shaft , manhole openings with cover and making connection etc., of effective depth 1.5 metre and overall depth of 3 metre complete all as described and shown on Drg No CEPZ/C-TD/013 /13 dated 11 -09- 2013 sheet 1/5 to 5/5.

M&L for Soakage well of size 2.40 m dia x 3.00 m depth including excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed brick masonry in CM 1:4 with sub class B bricks, top ring of RCC, M-25 design mix concrete including intercepting chamber and screen chamber made of Brick masonary in CM 1:4, RCC cover slab in M-25 design mix & SFRC MH cover incl interconnecting pipes of RCC/DWC complete filled with brick bats complete all as shown on Drg No CEPZ/C-TD/013 /13 dated 11 -09- 2013 sheet 1/5 to 5/5 .

M&L for point wiring for one light point / fan point / bell point controlled by one switch with 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (RYB) for phase, black for neutral and 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable as earth lead drawn in as earth continuity wire connected to common earth dolly and each terminal/joints fitted with thimble and including concealed non metallic rigid PVC conduit not less than 20 mm dia of thickness not less than 1.8mm including CI/MS terminal box of required size including 3mm thick plastic laminated top sheet cover fitted with brass screw and cup washer including cutting chases to walls and making good the disturbed surfaces to match with the existing specifications, complete all as specified and directed. Note : In ceiling portion surface conduit wiring with clamps fixed with fasteners shall be carried out.

All as per Srl item No. 105.00 here-in before but for one 5 pin 5/6 Amps socket outlet on same board controlled by one switch 5 amp one way, complete all as specified and directed.

All as per Srl item No. 105.00 here-in before but for one 5 pin 5/6 amps socket outlet in independent board controlled by one switch 5 amp one way, complete all as specified and directed.

All as per Srl item No. 105.00 above but for one 15/16 Amp independant socket outlet point using 4.0 Sqmm FRLS PVC insulated unsheathed multi-strand copper conductor cable incl FRLS PVC insulated unsheathed multistranded copper conductor cable of size 4.0 Sqmm (green colour) earth wire connecting to earth dolly. complete all as specified and directed.

S & F Switch piano flush type single pole one way 6 Amps 240 volts with polycarbonate body complete all as specified and directed.

S&F ceiling rose surface bakelite 2 to 3 terminals with polycarbonate body complete all as specified and directed.

S&F socket outlet 6 amps 5 pin flush type, 240 volts with polycarbonate body complete all as specified and directed.

S&F socket outlet, 6 pin 5/6 and 15/16 amps multi purpose 2 in 1 flush type, 230 volts with polycarbonate body complete all as specified and directed.

S&F switch piano flush type single pole one way 15/16 amps 230 volts with polycarbonate body complete all as specified and directed.

S&F fan regulator electronic, step type hum free with polycarbonate body suitable to control speed of fan from 0 to 100% and connecting electrically all as specified and directed.

S&F lamp holder batten type polycarbonate body with back plate for batten fitting, fixing with proper round block complete all as specified and directed.

Supply, assembling and hanging ceiling fan with blades, down rod and accessories, 230volts, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) including making connections using 3 core 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning complete all as specified and directed.

S&F building security light luminaire 30 Watt, IP 66, AC 230 volts made up of pressure die cast iron housing complete including bracket of light grade pipe along with clamps, nut bolts and washers, making connection using PVC insulated and sheathed 3 core multi stranded copper conductor cable of size 0.50 Sqmm from ceiling rose fixed with of suitable size complete all as specified and directed.

S&F LED lamp 12 watt PF>0.90, 230 volts retrofit type complete all as specified and directed. Note:- The contractor shall produce LM-79 & LM-80 test repots from NABL accredited lab .

S&F LED light fitting 1x 20W, 4 feet, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED light fitting 1x9w/1x10w bulk head luminaires incl LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Note for srl item No 117 to 121 1. Driver shall be potted anti-vibration types. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be provided. 3. CRI (Colour Rendering Index) of fixture shall be > 70. 4. CCT (Colour Co-related Temperature of fixture shall be 5700K + 300 K. 5. System Lumen Efficacy shall be > 100 Lm/W. 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 2 years guarantee shall be provided by contractor supported by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type. 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the contractor shall replace/repair the defective fitting within 07 days after handing over to contractor for replacement/repair. 11. CA No. shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintenance required, if any can be carried out from Top cover. 14. An amount equal to 5% of LED light work shall be retained from contractor's final bill amount as security deposit for the LED light work for the guarantee period as stated above and the same shall be released to the contractor after expiry of the guarantee period. The contractor may at his discretion submit fixed deposit receipt for the said sum from a scheduled Bank in lieu of the same to be retained out of the final bill.

S&F exhaust fan AC single phase 230/240 V 150 mm sweep, 5 blades off white colour model DX made of polycarbonate body with louvers on metal frame with screws/nuts & bolts complete all as specified and directed.

M&L for earthing complete with GI earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of earth plate not less than 1.5 Mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means bolt, nuts, check nuts and washer made of galvanised iron or steel including earth work in any type of soil, charcoal dust and salt layers 15cm thick all around the earth plate as shown in electrical plate No. 03 of SSR Part-I 2009 including 20mm bore GI watering pipe 'medium grade' with funel and wire mesh and 15mm bore GI protection pipe 'light grade' from earth pit to main board including PCC pit in cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) and including angle iron frame of size 40x40x3mm with hold fast embeded in PCC, RCC pit cover with suitable handle and earth work and removal of surplus soil to a distance not exc 50 Mtr, complete all as specified and directed.

S & F Sheet metal enclousre for DBs double door single pole and neutral with 200 amps rated bus bar of 8- way, 240 volts complete all as specified and directed.

S&F 240 volts 10KA 'B' curve miniature circut breaker (MCB) of single pole, current carrying capacity 6 to 20 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.

S&F 240 volts 10KA 'C' curve miniature circut breaker (MCB) of single pole and neutral current carrying capacity upto 32 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.

S&F electric water heater, storage type steel body with copper inner tank and heating element 2 KW, capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc fixed to wall with MS fasteners, nuts and washers complete all as specified and directed.

S&F sheet metal encloser single pole and neutral 240 volt , 20 Amps with two pin and earth plug and socket plug top complete with single pole MCBs all as specified and directed.

M&L for cutting existing GI pipe line of size 15/20 mm bore dia making new connection including provn of short pieces, inserting Tees, bends, sockets, union etc with existing water pipe line complete all as specified and directed.

S&F anchor bolt 12 mm X 100 mm long complete all as specified and directed. (Note: Anchor bolt shall be grouted with hammer drill only and making good to disturbed surface as per existing)

M&L for dry clean fine river sand as in sand cushioning to underground cable 23cm thick (8cm before laying & 15cm after laying cable) including punning down of sand layer complete all as specified and directed. Note :- Punned thickness shall only be measured and paid.

Supply & laying sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry across the cable with width of protection cover equal to length of brick complete all as specified and directed.

Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated PVC sheathed, armoured heavy duty electric cable, with aluminium conductor 10 Sqmm x 2 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover, protection pipe etc. shall be measured and paid for separately.

S&F GI tubing light grade 40 mm bore cut to size and fixed along the pole for cable protection including clamp 02 Nos of size 25x4 mm, nut bolts , washers etc all as required at site including taking out old one complete all as specified and directed.

M/S NARESH KUMAR SHARMA

AV ENTERPRISES

Bidder Name

RD Engineers

AV ENTERPRISES

M/S NARESH KUMAR SHARMA