Development of Play field at Lamber Banihal, District Ramban (Incl. taxes)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (Exceeding 30cm in depth, 1.5mtr in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.50 m, disposed earth to be levelled and neatly dressed:All kinds of soil

Earthwork in surface excavation not exceeding 30cm in depth but exceeding 1.5mtr in width as well as 10sqm on plan including disposal of excavated earth upto 1 mtr from cutting edge, lift upto 1.5mtr, disposed earth to be levelled and neatly dressed in :All kinds of Soil:

Supplying & filling of good earth at site incl. rolling with 8-10 mtr capacity road roller, compaction, levelling as required at site, carriage and royality complete job.

Making kintted wire crates of approved mesh size 100 mm x 100 mm incl. weavinf binding sides and partions, and binding top after Hand packed stones in wire crates incl. cost of filling stones and weaving material tipping stone filled wire crates in position incl. equipment charges incl. all carriages complete job crate size 16' x 4' x4'

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Preparing and dressing side slopes of canals for lining.In soils admixed with more than 40% shingle / kankar / boulder

Dry stone pitching 225 mm thick, incl. cost of stones and prepration of surface quarry stone.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level.1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size)

Providin.9 and laying in position specified grade of reinforced cement concrete excluding the cost of centenng. shuttering, finishing and reinforcement-All work upto plinth level.1.1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.Thermo-Mechanically Treated bars.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level.1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size)Crushed

Supply & filling of RBM/ quarry muck/Khakh bajree inside tires incl. all leads & lifts in layers not exceeding 20 cm in depth consolidating each layer by ramming and watering etc complete.

Strctural steel work riveted or bolted in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing G. I. chain link fabric fencing of required width in mesh size 50x50mm including strengthening with 2mm dia wire or nuts, bolts and washers as required complete as per direction of Engineer-in-charge.Made of G. I. wire of dia 4mm

Strctural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge)0.50mm+/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240 mpa steel grade5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5 x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.l. limpet washers or with G.l. limpet washers filled with white lead complete upto any pitch in horizontal /vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required

Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 ( 1 cement : 6 fine sand)

Extra for brick work in superstructure above plinth level upto floor V level. (By manual means)

15mm Cement plaster on the rough side of single or half brick wall of mix:1 : 6 ( 1 cement : 6 fine sand)

Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade New steel work (two or more coats)

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works.

Cement concrete flooring 1:2:4 ( 1 cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.50 mmthick with 20mm nominal size stone aggregate. Crushed.

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (Not exceeding 1.5 mtr in width) and for shafts, wells, cesspits and the like not exceeding 1 Osqm on plan, depth upto 1.5mtr. including disposal of excavated earth upto 1 mtr from cutting edge, disposed earth is to be levelled and neatly dressed in: All kinds of soil

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutmen"ts, posts ans sturts, etc. upto floor five level excluding cost of centring, shuttering, fmishing and reinforcement.1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size)

Centering & shuttering incl. struting, propping etc and removal of form: Foundations: footings, bases of columnsetc. for mass concrete.

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and centilevers

Wal!s of (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

Edges of slabs and breaks in floors and walls.

Providing and laying damp-proof course 5Crnm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand 4 graded stone aggregate 20mm nominal size Crushed

Applying a coat of residual petroleum bitumen of Grade VG- 10 of approved quality using 1.}kg per square metre on damp-proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth inCement mortar 1 :4 ( 1 cement : 4 coarse sand)

Half brick masonry with bricks of class designation 75 in foundations and plinth in : Cement mortar 1 :4 ( 1 cement : 4 coarse sand)

Extra for half Brick masonry in superstructure above plinth level upto floor V level.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber neoprene gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- Charge (glazing, panelling and dash fasteners to be paid for separately.) Polyester powder coated aluminium (minimum thickness of polyester powder coated 50 kg 408.55 microns)

For shutters of doors, windows & ventilators including providing and fixing hinges I pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber I neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminium (minimum thickness of powder coated 50 microns) SUBHEAD- 24.0

Providing and fixing 12mm thick prelaminated particle boardflat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-l type-11) in panelling fixed in aluminium doors, windows shutters and partition frames with C. P. brass I stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Honey-comb brick work 10/11.4 em thick with bricks of class designation 75 in cement mortar 1:4 (1 cement: 4 coarse sand)

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete

Tile work in skirting, risers of steps and dado (upto 2m height) over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing in position collapsible steel shutters with vertical channels 20x1 Ox2mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T -iron 40x40x6mm with 40mm dia, steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer,

Providing and fixing circular cast iron box for ceiling fan clamp 140 mm internal dia., 73mm height, 5mm thick rim, bottom and top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding top lid shall bescrewed into the cast iron box by means of 3.3mm dia. round headed screws, one lock at the corners. Clamps shall be made of 12mm dia M.S. bar bent to shape as per standard drawing

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface Water thinable Cement primer

Wall Painting with plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 litre/1 Osqm over and including base coat of water proofing cement paint applied@ 2.20kg/1 Osqm)

Concealed pipe incl. painting with anti coreosive bitumastic paint cutting chase and making good the wall 15 mm nominal bore

20 mm dia. nominal bore

Providing and fixing ball valve (brass) of approved quality complete 25 mm nominal bore

Providing and fixing brass stop cock of approved quality.15 mm nominal bore

Providing and fixing G.l. Union in G.l. pipe including cutting and threading the pipe and making long screws etc. complete (new work) 25 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license].

Constructing masonry Chamber 30x30x50 em, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C.l. surface box 1 00x1 00x75 mm (inside) with hinges Cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation, foundation concrete 1:5:10 (1 cement :5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.With F.P.S. bricks crushed

Providing and fixing water closet squatting pan ( Indian type W.C. pan) with 100 mm sand cast Iron P or Strap, 10 litre low level P.V. C. flushing cistern including flush pipe (of approved make) "manually contro(led device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x41 Ox265 mm sizes respectively with automatic flushing cistern with C. I./M.S. brackets standard size of G. I. flush pipe and C.P. brass spreaders with brass unions and G. I. clamps complete, including painting of fittings and brakets, cutting and making good the walls and floors wherever required:

Providing c;1nd fixing wash basin with C. I./M.S. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing c;1nd fixing wash basin with C. I./M.S. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: Orissa pattern white vitreous china W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing G. I. inlet connection for flush pipe connecting with W.C. pan.

Providing and fixking of PVC waste pipe for sink or washbasinincludingn PVC waste fittings semi rigid pipe 32mm dia 32mm dia

Providing and fixing mirror of superior glass( of approved quality) and of required shape and size with plastic . moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm

Providing and fixing of PVC pipes and other accessories: 100mm dia

75mmdia

100mm dia plain bend

75mm dia plain bend

100 dia door bend

75mm dia door bend

100 dia tee

75mm dia tee

100mm dia grating

Providing & fixing of powder coated aluminum fittings Tower bolts 200mm

Handles 200mm

Handles 150mm

Door stopper

slidingn door boltg

wiring for lighting points with 1.5mm sq. cable PVC insulated multistandard copper wire 650/1100 V grade incl switch and modular plate for fan, lighting points, tube lights and exhaust fans.

wiring for power/ heating points with 2.5 mm sq cable pic insulated multi standard copper wire 650/1100 V grade inlc. Switch socket and modular plate.

Providing , fixing , connecting and tesitn of B Holder with plate screws incl. LED Lamp.

Providing and fixing connecting and testing of ceiling fan incl. hook and round plate

Providing and fixing connecting and testing of exhaust fan with round plate

Providing and fixing connecting and testing of fan dimmer.

Providing and fixingh of factory fabricataed powder coated sub distribution board having provision for fixing of MCB,s (16 way)

Providing and fixing of connecting and testing of 10 to 32 amp MCB's Pole

Providing and fixing of connecting and testing of PVC insulated multistandard copper wire 650/1100 V grade main panel to sub distrubution boards and circuits: 4mm

Providing and t esting and commissioning of erthing with earthing plate embedded in 6 ft deep pit to be excavated and refilled with charcoal, salt and swg wire connected with control panel.

Providing and layking of aluminium amoured cable 35mm 3.5 core to be laid in cable trenchthe job inlcudes connecting of thimbles, clamps wherever required.

Carriage ofmaterial from source to site by M.T for 10km lead sand and aggregate

Note :- 1) Any Tropical error shall be consider as per sanction schedule of rates/ estimates.

Sheikh Manzoor Ahmed

M/S MOHD AMIN AND SONS

EIMSIM BABAS INFRASTRUCTURE PVT LTD

M/s HIGH WAY CONSTRUCTIONS

Maqsood Ahamed