Interior Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

BILL OF QUANTITIES (BOQ)

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

S.No. Sub-Head DSR Amount Non DSR Amount

1 CIVIL & INTERIOR WORKS 1728466.67 3957299.76

2 FURNITURE 1528327.90

3 ELECTRICAL WORKS 3786212.37 2158202.00

4 PLUMBING & FIREFIGHTING WORKS 194031.10 221169.39

TOTALAMOUNT 6695645.00 8490568.00

GRAND TOTAL I/C GST (DSR+NDSR) 15186213.00

GRAND TOTAL I/C GST (DSR+NDSR) 15186213.00

Digitally signed by ASHWANI

ASHWANI KUMAR BANSWAL

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla,

CIVIL & INTERIOR WORKS

S.No. Description of Works Amount

Amount (SR, in Rs.)

2 Masonry & Plaster 284,529.81 21,859.41

3 Paving & Wet Works 761,331.75 454,037.37

4 Partitions & Wall Cladding 87,018.55 2,013,624.72

7 Finishes & Miscellaneous 59,116.00 453,560.18

GRAND TOTAL (Carried Forward) 5,685,766.43

GRAND TOTAL (Carried Forward) 5,685,766.43

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

CIVIL & INTERIOR WORKS

Dismantling tile work in floors and roofs laid in cement mortar including stacking

material within 50 metres lead.

15.23.2 For thickness of tiles above 25 mm and up to 40 mm SQM 380.00 93.40 35492.00

Based on Dismantling tile work in Wall dado laid in cement mortar including stacking material

15.23.2 within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for

plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Demolishing brick work manually / by mechanical means including stacking of

1.4 15.7 serviceable material and disposal of unserviceable material within 50 metres lead as

per direction of Engineer-in-Charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including

chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:

15.12.1 Of area 3 sq. metres and below EACH 2.00 302.70 605.40

15.12.2 Of area beyond 3 sq. metres EACH 2.00 414.55 829.10

Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false

1.6 15.57 ceiling including disposal of unserviceable surplus material and stacking of SQM 145.00 46.50 6742.50

serviceable material with in 50 meters lead as directed by Engineer-in-Charge.

Demolishing cement concrete manually / by mechanical means including disposal

of material within 50 metres lead as per direction of Engineer-in - charge.

15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) CUM 2.00 2007.50 4015.00

Dismantling C.I. pipes including excavation and refilling trenches after taking out the

pipes, manually / by mechanical means breaking lead caulked joints, melting of

lead and making into blocks including stacking of pipes & lead at site within 50

metre lead as per direction of Engineer-in-Charge:

Dismantling G.I. pipes (external work) including excavation and refilling trenches

1.9 15.44 after taking out the pipes, manually / by mechanical means including stacking of

pipes within 50 metres lead as per direction of Engineer-in-Charge:

Dismantling of flushing cistern of all types (C.I. /PVC/Vitrous China) including stacking

1.11 15.52 of useful materials near the site and disposal of unserviceable materials within 50 Nos 2.00 744.60 1489.20

MR Based on Dismantling o Wash basins, Urinals, WC including stacking of useful material near the

item No 15.52 site and disposal of unservicable materials within 50 metres lead

Demolishing R.C.C. work manually / by mechanical means including stacking of

1.13 15.3 steel bars and disposal of unserviceable material within 50 metres lead as per cum 1.00 2928.10 2928.10

direction of Engineer-in-Charge.

Extra for cutting reinforcement bars manually / by mechanical means in R.C.C. or

1.14 15.5 R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) sqm 5.00 947.10 4735.50

as per direction of Engineer - in -charge.

Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B.

Carriage of material by mechanical transport including loading unloading and

1.1.1 Lime, murrum, building rubbish

TOTAL OF DISMANTLING 102013.95 18356.79

2 MASONRY AND PLASTER

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

2.1 11.3 aggregate) finished with a floating coat of neat cement, including cement slurry,

but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 380.00 545.00 207100.00

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) SQM 25.00 1018.05 25451.25

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

course of half brick masonry.

CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick

2.5 13.4 12 mm cement plaster of mix

Reinforced cement concrete work in beams, suspended floors, roofs having slope

up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,

2.6 5.3 staircases and spiral stair cases up to floor five level excluding the cost of centering, CUM 1.00 10719.30 10719.30

shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size).

2.7 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

2.8 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers SQM 6.60 608.35 4015.11

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing

in position and binding all complete above plinth level.

5.22A.4 Hot rolled deformed bars kg 15.00 89.65 1344.75

POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm to 15mm thick

2.10 MR POP Punning over cement plaster in line & plumb finished smooth to receive paint. SQM 45.00 248.71 11191.83

(Internal surfaces of walls).

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

Providing and laying water proofing treatment in sunken portion of WCs, bathroom

etc., by applying cement slurry mixed with water proofing cement compound

consisting of applying : a) First layer of slurry of cement @ 0.488 kg /sqm mixed with

water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air

2.11 22.5 cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/ sqm mixed with SQM 34.00 516.60 17564.40

water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air

cure for 4 hours followed with water curing for 48 hours. The rate includes

preparation of surface, treatment and sealing of all joints, corners, junctions of pipes

and masonry with polymer mixed slurry.

FOAM CONCRETE FILLING UNDER TOILETS AND PNTRY:- Filling and compacting Foam

Concrete for raising level of toilets and pantry and finishing in a coat of lean

concrete screeding with waterproofing compound complete in all respects to take

Tile Flooring as per flooring specifications.

SUB TOTAL OF MASONRY AND PLASTER 284529.81 21859.41

3 PAVING AND WET WORKS

TILE DADO :- Providing and fixing Ist quality ceramic glazed wall tiles conforming to

IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all

colours, shades except burgundy, bottle green, black of any size as approved by

3.1 8.31 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of SQM 115.00 1063.45 122296.75

cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @

3.3kg per sqm, including pointing in white cement mixed with pigment of matching

shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to

be specified by the manufacturer) with water absorption less than 0.08%

and conforming to IS:15622, of approved brand & manufacturer, in all

colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:

4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including

grouting the joints with white cement and matching pigments etc. The

tiles must be cut with the zero chipping diamond cutter only . Laying of

tiles will be done with the notch trowel, plier, wedge, clips of required

thickness, leveling system and rubber mallet for placing the tiles gently

11.41A.2 Glazed vitrified floor tiles polished finish of size

CERAMIC TILE FLOORING :- Providing and laying rectified Glazed Ceramic floor tiles

of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st

quality conforming to IS : 15622, of approved make, in all colours, shades, except

White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1

Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including

pointing the joints with white cement and matching pigments etc., complete.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix

of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg

of resin per kg), including filling / grouting and finishing complete as per direction of

Engineer-in-charge

KITCHEN/ PANTRY/ HAND WASH COUNTER :- Providing and fixing pantry and toilets

with Granite stone top or Solid Acylic Surface (with straight edge polished nosing)

complete with base cabinet made of 20mm BWP board, outside surface (shutters)

finished in 1mm thick Laminate of approved shade. All internal surfaces to have

balancing laminate. The rate inclusive of necessary hardware, handle lock sets, self

closing hinges, spring loaded shutter, latch inside, all cabinet hardware complete as

per Archnter itects approval. The height of the Conter is to be upto 900mm and

Width of work top counter 600mm/ as per the detailed drawings.

Providing and Fixing of floor tiles with wear layer is of 0.5mm, made upof Stone

Polymer composite, 100% Water & Termite proof, Scratch/ Flame/ UV resistant, anti-

3.6 MR microbial, 100% recyclable Green product having click system with suitable skirting. SQM 95.00 2925.33 277906.71

Classification of abrasion resistance (Abrasion wheelfromH-18 Calibrade,

loadApplied 1000 grams, No. of Cycles 14,400). " ( Along with Matching Profiles)

Supply of modular carpet of approved model and shade and made with 100%

nylon 6/6.6 tufted textured tiles of minimum 500mm x 500mm in size, stain resistant,

anti microbial, and having colour fastness to water, fastness to light, rubbing fastness

and castor chair suitability as per relevant standard for heavy commercial usage,

with 100% PVC free Wellbac Function Backing with having average density 6000

3.7 MR oz/cu. yd. or more,Nominal total thickness of 5.9mm, and Pile weight – 16-18 oz/ sq SQM 50.00 2162.00 108100.00

yard. Material shall be CRI GREEN LABEL PLUS certified, and shall have recycled

content complying to GRIHA requirement, including fixing with GRIHA compliant

adhesive of approved make, minimum 15 years manufacturer's warrantee, all

complete as per drawings, manufacturer's specifications and direction of Engineer in

TOTAL FOR PAVING & WET WORKS 761331.75 454037.37

4 PARTITIONS AND WALL CLADDING

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height consisting

of G.I. frame and required board, including providing and fixing of frame work

made of special section power pressed/ roll form G.I. sheet with zinc coating of 120

gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide

having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at

the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50

mm length or suitable anchor fastener or metal screws with nylon plugs and the

studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50

mm thick fixed vertically within flanges of floor and ceiling channel and placed at a

spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of

studs along both ends of partition fixed flush to wall with suitable anchor fastener or

metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of

boards to both side of frame work by 25 mm long dry wall screws on studs, floor and

ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid through

cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5

mm each) to be provided at the horizontal joints of two boards, fixed to the studs

using metal to metal flat head screws, including jointing and finishing to a flush finish

with recommended jointing compound, jointing tape, angle beads at corners (25

mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as

per manufacture's specification and direction of engineer in charge all complete.

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass

Reinforced Gypsum (GRG) plaster board conforming to IS: 2095:

Gypsum Panelling:-Providing and fixing, in position concealed G.I. section for wall

paneling using board of required thickness fixed on the ‘W’ profile (0.55 mm thick )

having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55

mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and

another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm.

4.2 9.133 Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610

mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the ‘W’

profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as

per the drawing & directions of engineer-incharge, the joints of the boards are

finished with specially formulated jointing compound and 48 mm wide jointing tape

to provide seamless finish.

9.133.3 Gypsum board conforming to IS: 2095 Part - I

GLASS PARTITIONING:- Providing & Fixing Full Height Glass partition using 12mm Thk.

Glass with anodised Aluminium frame fixing glass with snap on option consisting of

top, bottom and side frame measuring 40-46mm x 18mm-25mm complete with

glazing rubber as per manufacturer's specifications and instructions of Engineer- in-

charge. Rate include supply & Installation of 12 mm thk toughened glass with

double sided adhesive tapes for glass to glass butt joints. Partition system from FFL to

False Ceiling level, inclusive of cost of support required for fixing in the ceiling. The

frame to be powder coated in desired shade as per the instructions of the Architect.

PLYWOOD PARTITIONING- Plywood partition using 12mm fire retardant ply fixed

on both sides on aluminium Studs Frame 50mm x 50mm x 0.5mm & 50mm x

4.4 MR 60mm x 0.5mm as per approved sample and architectural drawings placing the SQM 130.00 3287.13 427327.16

same 600mm c/c . Aluminuim frame to be fixed to floor and RCC Ceiling using

PLYWOOD PANELLING- Plywood panelling using 12mm fire retardant Ply fixed on one

4.5 MR side on Aluminium Frame 50mm x 25mm as per approved sample and architectural SQM 205.00 2059.48 422193.05

drawings. Aluminium frame to be fixed to walls, floor and RCC Ceiling using fastners.

VEENER CLADDING- Providing and Fixing 4.0 mm thick decorative /Natural Veneer of

approved design and shade , cladded on to existing partitioning. Complete

Cladding to be finished using mellamine polish (gloss/matt) as approved by the

engineer in charge.

LAMINATE CLADDING- P/F 1.5 mm thick laminate including 4 mm thick MDF as per

the pattern or design required at site on an existing Plywood surface, complete with

filling of grooves with matching or contrast color, as per the direction of the engineer

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool

conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G

4.8 12.62 Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and in SQM 145.00 277.90 40295.50

position by criss cossing GI wire etc. complete as per directions of Engineer-in-

SHELVES:- Providing and fixing Pre-laminated flat pressed 3 layer (medium density)

particle board or graded wood particle board IS : 3087 marked, with one side

4.9 9.18 decorative and other side balancing lamination Grade I, Type II exterior grade IS :

12823 marked, in shelves with screws and fittings wherever required, edges to be

painted with polyurethane primer (fittings to be paid separately).

Cabinet Carcass- Providing and fixing Pre-laminated flat pressed 3 layer (medium

density) particle board or graded wood particle board IS : 3087 marked, with one

4.10 side decorative and other side balancing lamination Grade I, Type II exterior grade SQM 5.00 1501.00 7505.00

IS : 12823 marked, in cabinet carcass with screws and fittings wherever required,

edges to be painted with polyurethane primer (fittings to be paid separately).

Providing & fixing IInd class teak wood lipping 25 mm wide x 12 mm thick complete

with all necessary nails, hardware etc.

Providing and fixing special quality bright finished brass cupboard or ward robe locks

with four levers of approved quality including necessary screws etc. complete.

4.13 9.81 Providing and fixing bright finished brass handles with screws etc. complete:

SHUTTERS:- Providing and fixing cup board shutters 25 mm thick, with Pre-laminated

flat pressed three layer particle board or graded wood particle board IS:12823

marked, exterior grade (Grade l Type ll), having one side decorative lamination and

other side balancing lamination, including IInd class teak wood lipping of 25 mm

wide x12 mm thick with necessary screws and bright finished stainless steel piano

hinges, complete as per direction of the Engineer-in-Charge

STORAGE CABINET FOR ELECTRICAL PANEL AND VOLTAGE STABLIZERS- Cabinet

Shutters out of 19mm Commercial Plybaord finished in 1mm Laminate of base cost

Rs. 380 per sqmt. Shutters to be fixed to a frame. Rigidly fixed on both sides and top

4.15 MR finshed in laminate. No internal carcass required. All Hinges of hettich or equivalent. SQM 4.00 2385.01 9540.03

Internal Surface of the shutter in balancing white laminate. All shutters to be

provided with Stainless steel louvers at the top and bottom of the shutter as per the

site requirements and instrcution of the Engineer In charge.

Steel work welded in built up sections/ framed work, including cutting, oisting, fixing

4.16 10.25 in position and applying a priming coat of pproved steel primer using structural steel

etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works Kg 35.00 142.30 4980.50

SUB TOTAL OF PARTITIONS AND WALL CLADDING 87018.55 2013624.72

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

GYPBOARD CEILING :- Providing and fixing false ceiling at all height including

providing and fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as

per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with

flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the

ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other

flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with

5.1 12.45 nuts & bolts of required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be

fixed in a direction perpendicular to G.I. intermediate channel with connecting clips

made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

Including jointing and finishing to a flush finish of tapered and square edges of the

board with recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two coats of

primer suitable for board, all as per manufacturer's specification and also including

the cost of making openings for light fittings, grills, diffusers, cutouts made with frame

of perimeter channels suitably fixed, all complete as per drawings, specification and

direction of the Engineer in Charge but excluding the cost of painting with :

a) 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I SQM 175.00 1145.95 200541.25

Providing & fixing Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in

Aluminum alloy grade 6063. The baffle blade shall be in size of 100x 25 x 3600mm in

5.2 Wood grain finish – Pradoo & Cabrueava. The baffle blade shall be suspended using SQM 15.00 7767.40 116511.06

Slotted U-profile at center-to-center spacing of upto 150mm. Longer lengths of Baffle

to be connected by Baffle Joiner and the ends to be fixed with End caps.

WOODEN VENEER CEILING :- Providing and fixing wooden veneer ceiling by Fixing

Natural Teak Veneer on 12mm Underlay commercial Ply fixed to a subframe made

using 50mm X 50mm Kiln seasoned and chmeically treated hollock wood fixed to

RCC ceiilng using Fastners . The cost to inlcude the finishing of the Veneer using

wood stain and clear coat of PU (Gloss/ Matt) as per the instructions of the Engineer

300MM X 1200MM MINERAL FIBRE GRID - Providing & Fixing of Mineral Fibre

Acoustical Suspended Ceiling System with Bevelled Tegular Edge Planks With 15mm

Exposed silhoutte Grid. The planks should have Humidity Resistance (RH) of 99%, NRC

0.5, Light Reflectance ≥85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Colour

White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 1200 x

300 x 16mm , suitable for Green Building application, with Recycled content of 35%.

The tile shall be laid on 15 mm wide T - section flanges having rotary stitching on all T

sections i.e. the Main Runner & 1200 mm Cross Tees with a web height of 38mm and

a load carrying capacity of 12.67 Kgs/M2 & minimum pull out strength of 100 kgs..

The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with

Suspension system. The Tile & Grid system used together should carry a 30 year

TRAP DOOR :- Providing and fixing trap door in false ceiling made of "Novapan "pre-

5.5 MR laminated board with hardwood framing, dead locks, lapping all around including SQM 2.00 2913.67 5827.33

all hardware, hinges etc. complete as per design and drawing.

CEILING PELMETS :- Providing and fixed pelmet of overall size 150mmx150mm and

made hardwood framings hung from ceiling @1000mm centre to centre with 1 nos

of 12mm thk. fire retardant ply on vertical & 12mm thk. Commercial ply on

horizontal surface (straight & curved). Inclusive of finishing in Paint.

Providing the gypsum double sided cove of 150mm x 150mm having a facia of

75mm to macth the specifications same as above

Providing the wooden cove of 150mm x 150mm having a facia of 75mm to macth

the specifications same as above.

GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all round the

mineral fibre/ gypsum ceiling. In order to make the Mineral Fiber/ gypsum ceiling

higher than the Gypsum Ceiling by upto 100mm as per drawings. (visible surface of

gypsum band to not exceed 100mm) including plastic emulsion paint.

Providing and fixing in true horizontal level Triangular Open cell GI lay-in ceiling tiles

with border panels forming flush-tegular edge of size 600mmx600mmx38mm having

Fire Performance Class A1 (EN13964). The tile of „Global white‟ color with cell size

100mm X 100mm shall be laid on white painted Armstrong Suprafine XL15mm profile

grid system comprising Main runners (3000mm), 1200mm and 600mm cross tees with

15mm white flanges and 38mm web height. The grid should be of “Armstrong”

make with 15mm wide T - section flanges color white having rotary stitching on all T

sections i.e. the Main Runner with C3 coupling, 1200 mm & 600 mm Cross Tees with

Hardened XL2 Clip having a web height of 38 mm and a load carrying capacity of

14 Kgs/M. The T Sections have a Galvanizing of 90 grams per M2 with pull out

strength of 100 Kgs. Suspension system for Armstrong grid to be of Armstrong make.

SUB TOTAL OF CEILING 200541.25 839269.62

6 DOORS/ WINDOWS

35MM THICK LAMINATED FLUSH DOOR WITH FLOOR SPRING- 35mm thick flush Doors

finished using 1mm Thick Highland Pine Laminate on both sides panel of size upto

2400mm x 1050mm complete with Hardware including floor spring, Door Closer,

dead Lock with inbuilt key, D-Handle etc. including cost of teak lipping all around

with melamine/ duco finish. The item to include installation of all kinds of latches as

per the requirement.

DOOR FRAMES- Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position with hold fast lugs

or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall

be paid for separately).

9.1.1 Second class teak wood CUM 0.50 131576.95 65788.48

FLUSH DOOR:- Providing and fixing ISI marked flush door shutters conforming to IS :

2202 (Part I) non-decorative type, core of block board construction with frame of 1st

class hard wood and well matched commercial 3 ply veneering with vertical grains

or cross bands and face veneers on both faces of shutters :

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws SQM 8.40 2015.75 16932.30

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

Extra for Providing and fixing flush doors with decorative veneering instead of non

decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)

9.22.1 On one side only SQM 8.40 408.05 3427.62

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth

on all edges of flush door shutters (over all area of door shutter to be measured)

Providing and fixing wooden moulded beading to door and window frames with

iron screws, plugs and priming coat on unexposed surface etc. complete:

9.40.1 2nd class teak wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and embedding in cement concrete block

30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm

Providing and fixing bright finished brass butt hinges with necessary screws etc.

DOOR CLOSERS:- Providing and fixing aluminium extruded section body tubular type

universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on

6.9 9.84 the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 EACH 4.00 856.30 3425.20

mm), with double speed adjustment with necessary accessories and screws etc.

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH 123

6.10 MR with Roses & Escutcheon in SS packaged with Mortice lockset 55mm backset, 20 SS EACH 4.00 2894.71 11578.83

forend, SS strike plate and EP Cylinder for all flush doors.

HANDLES;- Providing and fixing bright finished brass handles with screws etc.

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked, anodised

6.12 9.97 (anodic AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade,

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door

stopper with necessary screws, etc. complete.

FIRE DOOR- Providing and fixing single leaf 120min Rated Fire Door of size 900x2400.

with vision panel using wired glass complete with Fire proof door frame. One side to

6.14 MR be finished in fire retardant paint and one side to be finished in Laminate of EACH 1.00 25537.03 25537.03

approved shade. All Frame to be finished in fire retardant paint. All hinges and

hardware to be thermatically sealed and 120 mins fire rated.

Providing and fixing 12 mm thick frameless toughened glass door shutter of

approved brand and manufacture, including providing and fixing top & bottom

pivot & spring type fixing arrangement and making necessary holes etc. for fixing

required door fittings, all complete as per direction of Engineer- incharge.

UPVC Windows : Supply and Fixing of Tripple Track/ Tripple Channel Factory

made UPVC Windows along with DGU/ Sandvich Glasses (6 mm Reflective Glass +

6.16 MR 12 mm Air Gap + 6 mm Plain Toughned Glass) on two tracks and SS Mesh on One SQM 5.00 14824.40 74122.00

Track inclding all required hardware i.e. handles, locks and other etc.,

complete as per the requirement of engineer in charge.

Supply of 75 mm Aluminium ( Grade 6063 ) Skirting with 15 micron anodising In

Natural Finish. Thichness 1.30 to 1.50 mm. Designed to conceal screws. Seamless

finish. Complete with Rubber / PVC Jointers and Gasketc complete as per the

engineer in charge.

SUB TOTAL OF DOORS 233915.36 156591.68

7 FINISHES & MISCELLANEOUS

PRIMER: Applying one coat of water thinnable cement primer of approved brand

and manufacture on wall surface. Water thinnable cement primer.

ACRYLIC EMULSION PAINT: Finishing walls with 100% Premium acrylic emulsion paint

having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali &

fungal resistance, dirt resistance exterior paint of required shade (Company Depot

Tinted) with silicon additives.

New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including

priming coat of exterior primer applied @ 0.90 litre/10 sqm.

7.3 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered

surface to prepare the surface even and smooth complete.

Painting with synthetic enamel paint of approved brand and manufacture to give

13.61.1 Two or more coats on new work SQM 10.00 131.45 1314.50

Providing & fixing imported decorative Poly décor fabric Wall Paper (Object) of

7.5 MR weight 475 g /sqm as per approved shade & design including prepration of SQM 25.00 3831.67 95791.74

surface with 2 coats of Nubin Glue based epoxy quote.

ZEBRA BLINDS - 190g/sqm, thickness - 0.50 mm - 0.70mm ( opaue part ),

Colorfastness to light - above 4 grade. Blind tube is made of Aluminum with a

diameter of 36mm, botom rail is made of Aluminumwith powder coated having

weight 390 gm/meter fitted with end caps in colour matching to thefabric and

mechanism is of plastic with chain and metal bracket. The Blinds comes with

Aluminum cover with the matching fabric designed on it. Aluminium profile should

have temper WP consisting of alloy 63400 along with anodizing of 10 micron and

powder coating of 60 micron. The tensile strenghth of profile should be 9.10 Kg/mm

square and elongation 18.The control clutch driveunit engineered heavy duty chain

drive pulley operating system consisting of gear clutch housing and locking plug

containing minimum 6 ribs and inserted at minimum of 38mm into roller tube. It is self-

lubricating Exclusive clutch with safety pins for secure bracket installation and

unlocking pin for quick manual removal. Universal clutch is most convenient for

large windows down to the smallest windows. It shall be driven by a ball chain

pulley with ball chain and can be positioned at Right hand or Left hand side of the

shade. Clutch gear ratio of 1.75:1 for reduced operating force on larger blinds..

Mounting hardware brackets universal brackets including end plug bracket with

lock down retainer device.Brackets finish of powder coated metal installation

brackets made of stamped and hardened steel. Roller tube circular-shaped

aluminium tube extruded from alloy 63400 and temper WP. Bottom rail flat-shaped

extruded aluminium from alloy 63400 and temper WP. Ball chain shall be 2mm

diameter cord with plastic balls moulded to form an endless ball chain. It is used for

raising or lowering action of the shades. Plastic parts all plastic components are UV-

stable compounds available white.

S.No. DESCRIPTION UNIT QTY RATE (DSR 2021) AMOUNT MARKET RATE AMOUNT

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface

7.7 M.R. with 15 yrs MCS warranty as approval of the Architect. (Only film surface area shall SQM 35.00 1936.29 67770.12

be measured and paid).

Providing and fixing of 4,6 mm thick annealed GRIHA rated lacquered glass

manufactured industrially by curtain coating process with PU lacquer (50 micron

thick), opaque (if viewed against a support wall) conforming to EN 16477 standards

for back painted glass , of approved color by Architect/ Client fixed with compatible

Silicone having Shear Bond Strength (Dry, 24 hours), greater than 450 kpa and tack

free time of 10 to 30 mins compatible for installation of mirror and lacquered glass /

Foam based double sided adhesive tape for instantaneous adhesion, compatible

with mirror and lacquered glass having Shear bond strength (Dry, 15 mins) of 250 to

7.8 M.R. 350 kpa) on a perfectly leveled 12mm thick water proof marine plywood / MDF / SQM 15.00 3532.63 52989.40

Mineral fibre board which is mounted on the RCC wall/any other structure. The

contractor should submit test reports for backpainted glass from manufacturer - High

humidity Resistance (conforms to BS EN 1036 1999); Color fastness ISO 105B02

standard & Mechanical Resistance ISO 7784 ( Taber Abrasion test ) ISO 2409 ( Cross

Hatch Test ) standard The manufactured backpainted glass should be

environmentally friendly (no lead, no arsenic, no copper, noformaldehyde);

appropriate recycled content (12% post industrial / 6% post consumer); compressive

strenght (1000 MPa) & tensile strenght (40 MPa),same as float glass

Providing & fixing 12mm Thick. 100% Acrylic solid surface of approved make and

colour using approved Adhesive to 12 mm thk. Waterproof Plywood of approved

brand as per shape, pattern & details given in the drawing. The rate includes

providing & fixing beading, cutting, scaffolding, nails, all materials, labour, lead, lifts,

HOM etc., complete.-for Lift Cladding. (The make, Shade, pattern etc., to be

approved by Architect).

Providing and Fixing Logo & Signage in 3D ,as per the approved Design/ pattern with

7.10 MR Mat /Gloss Finish Brass Letters with Mettalic/ Acrylic Base, complete as required at Sqft 5.00 5894.00 29470.00

site with the direction of the Enginner In Charge

SUB TOTAL OF FINISHES 59116.00 453560.18

SL Items Unit Qty Rate Amount

Supplying and placing in position Main desk of the following specifications. The Main table shall be of size 2700 Width mm x 1200 mm Depth x 750 mm height. Top

surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in Smart

Chief Case - space slides effortlessly in style.The mobile Pedestal shall be of size 480 Width mm x 640 Depth mm x 600 Height mm. Mobile pedestal shall be coated of MDF

Controller (medium density fiber ) with veneer coating and PU coating.The ERU Top shall be of MDF (medium density fiber) board duly finished with veneer and final PU

coating. Size of ERU top 1900 Width mm x 480 Depth mm x 550(not from ground with castors).The main desk is provided eith the wire management system also there

is perfect storage side unit .

Supplying and placing in position Back Unit of the following specifications. The Size of the Back unit shall be 1000 mm width x 480 mm Depth x 2035 mm height. The

2 Back Unit back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. The mobile unit can be bought in multiples.PU coating hardness Nos. 1.00 54,074.16 54,074.16

The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted wood & upholstered with leather and moulded polyurethane foam. Size of

back shall be (W)-46.0cm, (H)-57.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm. High Resilience (HR) foam should be used in making seat & back which shall

be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The back rest should be connected to the mechanism

with a drop-lift mechanism which can be adjusted in the range of 7.0+/-0.5cm for the comfortable back support to suitable individual need. Armrests should be

pressure die casted in polished aluminium with PP arm tops. The mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of

3 Main Chair 1:3, Synchronized tilt, Back tilt with 4 position locking and Side tilt tension adjustment knob should be operated while taking back support for better adjustment of Nos. 1.00 50,723.70 50,723.70

comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished

aluminium. it shall be fitted with 5 nos twin wheel castor. The size of head rest shall be (W)26.0cm x 12.0cm(L). The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-

centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. Overall dimensions of Chair shall be, Width of

Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 113.5 to max 138.0 cms. Seat height - min 41.0cm to max 51.0

cm. Dimensions tolerance / variations shall be within +/- 1 cm.

The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted wood & upholstered with leather and moulded polyurethane foam. The back

shall be designed with contoured lumber support for extra comfort. Size of back shall be (W)-45.0cm, (H)-49.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm.

High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888

4 Visitor Chair Nos. 1.00 31,974.23 31,974.23

for 25% compression. The understructure should be welded structure made up of M.S.E.R.W. ellipitical tube and the understructure should powder coated with 40-

60 micron DFT (Dry film thickness) Overall dimensions of Chair shall be, Width of Chair - 51.0cm, Depth of Chair - 66.5 cm as measured from base. Height from

ground - 96.0 cm. Seat height -48.0 cm. Dimensions tolerance / variations shall be within +/- 1 cm.

Providingin place of main table with overall size of table 2350 x 2350 x 750mm. The main table shall be of size 2350 x 1150 x 750mm. The side unit shall be 1200 x 600 x

750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft

closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate

board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board

5 JC/ GM confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and Nos. 1.00 91,043.01 91,043.01

approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thickustment which shall have stroke of 10.0 +/- 0.3 cm. The

pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of head rest shall be (W)26.0cm x 12.0cm(L). The size of

the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be inje

The Back Unit shall be of dimensions 2350 x 500 x 750mm. It shall be made of 25mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4

mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock

Providing and Placing in place of 3 seater leather sofa. The size of the sofa shall be 2080 mm x 920mm x 890mm. The soft foam offers sinking feeling along with

floating effect while seating. The pure leather upholstery offers a cool feelingto the body. High backrest shall support the entire body along with shoulder and head

for enhacned comfort. Solid wood frame which enhances the stability of the product. It shall have generous lumbar support. Round corners and soft edges shall be

there for safety. Pure Leather Thickness : 1.2 mm. Syn. Leather Thickness : 1 mm. Material : Combination of plywood and Solid Wood. Plywood thickness : 12 mm

(moisture resistance and treated). Moisture content : 10 -12 %. Foam- Material : Slab stock foam. Density : Super soft 32 kg/m3. Double webbing : S -spring and nylon

Providing and Placing in place of 2 seater leather sofa. The size of the sofa shall be 1410mm x 920mm x 890mm. The soft foam offers sinking feeling along with

floating effect while seating. The pure leather upholstery offers a cool feelingto the body. High backrest shall support the entire body along with shoulder and head

for enhacned comfort. Solid wood frame which enhances the stability of the product. It shall have generous lumbar support. Round corners and soft edges shall be

there for safety. Pure Leather Thickness : 1.2 mm. Syn. Leather Thickness : 1 mm. Material : Combination of plywood and Solid Wood. Plywood thickness : 12 mm

(moisture resistance and treated). Moisture content : 10 -12 %. Foam- Material : Slab stock foam. Density : Super soft 32 kg/m3. Double webbing : S -spring and nylon

Providing and Placing in place of 1 seater leather sofa. The size of the sofa shall be 1210mm x 920mm x 890mm. The soft foam offers sinking feeling along with

floating effect while seating. The pure leather upholstery offers a cool feelingto the body. High backrest shall support the entire body along with shoulder and head

for enhacned comfort. Solid wood frame which enhances the stability of the product. It shall have generous lumbar support. Round corners and soft edges shall be

there for safety. Pure Leather Thickness : 1.2 mm. Syn. Leather Thickness : 1 mm. Material : Combination of plywood and Solid Wood. Plywood thickness : 12 mm

(moisture resistance and treated). Moisture content : 10 -12 %. Foam- Material : Slab stock foam. Density : Super soft 32 kg/m3. Double webbing : S -spring and nylon

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded

assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded

assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.

Providing in place of main table with overall size of table 1650 x 1500 x 750mm. The main table shall be of size 1650 x 750 x 750mm. The side unit shall be 1050 x 500 x

750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft

closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate

board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board

24 Office Table confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and Nos. 1.00 71,769.93 71,769.93

approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thicke at every junction, including fixing perimeter channels

0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long. be fitted with 5 nos twin wheel castor. The size of head rest shall be (W)26.0cm x 12.0cm(L). The

size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be inje

Worktop shall be Made of 36mm thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top and having chamfered edge. Plastic ABS

access flap is provided for easy access to wires and cables. Work top is available as per layout. The Under-structure consists of mixture of 25mm and 18mm Pre-

laminated twin board of E1-P2 grade and approved shade Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for

Confrence connecting panels together. Modesty panel shall be made of 18mm Thick Pre-laminated twin board of E1-P2 grade Edge banded with matching 2 mm thick PVC

Room Table lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder

coated. An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to

mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to

pullout audio,video cables onto worktop and connect devices charger to power socket below worktop.

Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made

of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, &

hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S.

ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from

polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome

plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type,

13 Main Chair front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5- Nos. 1.00 18,118.53 18,118.53

position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder

coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the

up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic

height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The

pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and

assembled to pedestal.

Providing and Placing Visitors Chair with overall size of 60.9 W m x 64.2 D cm x 98.2 H cm x 44.8 Seat Height cm. The seat is cushioned seat made of injection molded

plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf

14 Visitor Chair as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size Nos. 1.00 12,779.14 12,779.14

1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The tubular frame is cantilever type and made of Ø2.54±0.03cm x

0.2±0.016 cm thick SS 202 tube. The back connected to frame through chrome plated high pressure die casted connector pipe.

Providing and Placing in place of dining table of following specifications. The overall dimensions of the table shall be 1600mm L x 900mm D x 750mm H. The table

15 Dining Table top shall be made from Mocha brown tempered glass. Understructure shall be Metal Black powder coated. Spacers will be provided underneath the table top to Nos. 1.00 23,290.24 23,290.24

give it a floating top look.

Providing and Placing in place of dining chairs. The overal dimensions of the chair shall be 435mm L x 595mm W x 870mm H. Seating height hsall be 470mm. The

16 Dinning Chair height of legs shall be 420mm. The upholstery shall be PU Leatherette. The seat foam thickness shall be 55mm and that of back shall be 30mm. Foam density shall be Nos. 1.00 8,912.68 8,912.68

28mm. Foam type shall be virgin foam. legs shall be black powder coated metal legs of dimensions 20 x 20 x 1.2mm.

Providing and placing panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium

trims. Fins shall be 22.8mm thick. Tiles: Combination of top tiles are fabric magnetic/fabric/fabric tackable/white board/glass writing board/ clear glass tile/

plain metal/ prelam tile. Bottom tiles - Plain metal/ fabric magnetic / fabric / laminated /prelam. The panel thickness comprises of 38mm (35 mm Minimum)

thick paper honeycomb + 3mm MDF on each sides + 0.6mm decorative laminate or fabric on both sides. The uprights and horizontals shall be made of aluminium

Work Station extrusion having average wall thickness of 1.2 mm & powder coated with epoxy- polyester powder. Particle board framing is used on outer boundary of these

(1500 x 1500) blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks are located in the mid segment of the panels and

can be provided with cutour support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of

variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is

integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T

spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam and upholstered with high stretch

knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3.

The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a

simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers impact cushioning while seating and synchronises with

the back movement during posture changes. The ‘S: shaped spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled

Polyamide form the back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt limiter

feature which is inbuilt in saet base and the tension is usulded plastic part polymer component is fitted to pullout audio,video cables onto worktop and connect

devices charger to power socket below worktop.heel castor. The size of head rest shall be (W)26.0cm x 12.0cm(L). The size of the pedestal shall be 65.0 +/- 0.5 cm

pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. Overall dimensions of Chair shall be, Width

of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedesta

Workstation : Providing and placing panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder

coated aluminium trims. Tiles: Combination of top tiles are fabric magnetic/fabric/fabric tackable/white board/glass writing board/ clear glass tile/ plain

metal/ prelam tile. Bottom tiles - Plain metal/ fabric magnetic / fabric / laminated /prelam. The panel thickness comprises of 38mm (35 mm Minimum) thick

paper honeycomb + 3mm MDF on each sides + 0.6mm decorative laminate or fabric on both sides. The uprights and horizontals shall be made of aluminium

extrusion having average wall thickness of 1.2 mm & powder coated with epoxy- polyester powder. Particle board framing is used on outer boundary of these

blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks are located in the mid segment of the panels and

can be provided with cutouts for mounting switch boxes (above or below the worktops). Top tiles can be offered in variety of combinations. The fins along the

depth shall be 22.8mm thick. Worksurface- out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200mm x 600mm x 750H. Brackets

Work Station shall be made from 2mm thick CRCA steel. Pedestals with legs - Nova pedestal flat metal front, free standing central locking of size 390 mm w x 435 mm d x

(1500 x 1050) 646 mm height 3dr = 2box+1file. The work shall be carried out as per the instructions and guidance received from engineer incharge. Providing and

placing ALL WOOD HINGED DOOR UNIT (HDU). Construction & Material Knockdown construction. Door Opening Twin door with self closing hinges of Wood made

from18mm Thick Pre Laminated Board. Handle · Aesthetically appealing recessed plastic handle for& wooden Doors. Locking Mechanism Cam lock · 3 point

locking mechanism in Wood Door Shelving · Height wise Adjustable Shelf Mounting. Wooden Top shall be be made from Pre-Laminated Board of 25 mm thk. Skirting

of 125 mm High shall be provided. Leveler Screw type adjustable Leveler with plastic base. height. Back Panel and Sides of the storageunits will be made out from

18mm thick Pre-Laminated Particle Board. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 10mm

of uneven flooring. The work shall be carried out as per guidance and instructions received from engineer incharge.

Providing & Installation of custom made veneer storages out of 19mm thk. Commercial Board finished in natural Teak finish veneer. All edges to be finished in teak

moulding as per design. The non visible areas to be finished with 0.8mm thk. balancing laminate of approved shade. The shutters to be provided as per design

(sliding of swing). All teak veneer surfaces to be finsihed in PU polish. The storage to be made complete as per approved drawing and satisfaction of engineer-in-

charge. (NOTE: Only the face area of the storage to be measured for payment.)

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla,

Electrical subhead

S.NO. SUB HEAD NDSR AMOUNT (Rs.) DSR AMOUNT (Rs.)

1 MAIN PANEL Rs. 270,365 Rs. -

2 DISTRIBUTION BOARDS Rs. - Rs. 27,540

3 CABELS / MAINS Rs. 200,391 Rs. 8,512

5 FIXTURES Rs. 277,287

6 WIRING FOR DATA AND VOICE OUTLETS Rs. 207,672 Rs. 98,185

7 CABLE TRAY.& RACE WAY. Rs. 103,171 Rs. 37,460

8 CCTV System Rs. 245,998

9 UPS & INVERTER SYSTEM Rs. 503,184

10 EPBAX System Rs. 475,371

11 FIRE DETECTION & PA SYSTEM Rs. - Rs. 637,622

12 Access Control System Rs. 288,431

GRAND TOTAL Rs. 5,944,414

GRAND TOTAL Rs. 5,944,414

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

S.No Description Unit Qty Rate MR Amount DSR Amount

1.1 MAIN PANEL

Design, manufacture, supply, installation, testing and commissioning of following LT

switchgear panels suitable for 415 V, 3 phase, 4 wire, 50 Hz power distribution system. The

panel shall be, Indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front,

dust and vermin proof type compartmentalized design fabricated out of 14 SWG sheet steel,

complete with aluminium bus bars, separate earth bus bar to be provided through out the

length of the panel. The incoming and outgoing feeders shall be accommodated in a

modular multitier arrangement, adequate size cable alley, painting, earthing, numbering,

danger plate etc. as required as per specifications and drawings.

One (1) no. 400A 4P Auto Transfer Switch. The ATS shall be suitable for auto as well as manual

mode operation, source priority and time delay setting.

One (1) No. 400A TPN MCCB 25KA

One (1) no. Dual Source KWH Meter with RS 485 port with 1 Set (3 No's) of suitable ratio, 15VA,

CL 1.0 C.T,s & control fuses.

One (1) No. Digital Volt, Current & Frequency (VAF) Meter with in built selector switch,

400A/5A CL-1.0,15VA resin cast CTs and control fuses.

Electrolytic high conductivity Aluminium four pole busbars rated at 500 amps having a

maximum current density of 1 amp per sq. mm insulated with heat shrinkable PVC sleeves.

One (1) set of Class B+C/Class I+II (according to IEC 61643) Surge Protection device Single

MOV with built in thermal fuse type with response time < 25 Nano seconds each with 3

numbers for the connection between Phase and Neutral and Spark Gap Encapsulated / Non-

exhausting type with response time of < 100 Nano seconds 1 number between Neutral and

Earth, Lightning impulse current 7 KA(10/350 µsec ) phase to neutral and 25 KA(10/350 µsec)

neutral to earth. OBO make

One (1) No. 160A, 10 KA TPN MCCB with Dual Source KWH Meter with RS 485 port with 1 Set (3

No's) of suitable ratio, 15VA, CL 1.0 C.T,s & control fuses.

One (1) No. 125A, 10 KA TPN MCCB.

Ten (10) Nos. 63A, 10 KA 4P MCBs "C" curve type

Six (6) Nos. 40A, 10 KA 4P MCBs "C" curve type

Three (3) Nos. 32A, 10 KA 4P MCB "C" curve type

Twenty One (21) Nos. 32A, 10 KA DP MCBs "C" curve type Set 1 270,365.09 270,365.09

The panel shall be IP52 ingress protection

All MCCBs above 200A rating shall be provided with microprocessor based protection

releases for short circuit, overload with 0.4 - 1 x In adjustable overload protection release.

All MCCBs below and including 200A rating shall be provided with thermal magnetic

protection releases for short circuit, overload protection with 0.8 - 1 x In adjustable overload

protection release.

All MCCBs shall be (Ics=100% Icu)

All MCCBs shall be provided with spreader terminals, phase barriers and rotary handle

operating mechanism.

MCB compartments shall be provided with transparent sheet cover. All outgoing feeders less

than 100A shall be provide with terminal block in cable alley.

Total of Main Panel over to summary 270,365.09 0.00

2 DISTRIBUTION BOARDS

Supply ,Installation, Testing & commissioning of following double door type distribution boards

fabricated out of 16 SWG, CRCA sheet steel recessed in wall or surface mounted.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution

board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including earthing etc. as required. (But

without MCB/RCCB/Isolator)

2.3.1 6 way , Double door Each 1 1,661.00 1,661.00

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker

2.3 2.10 suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

b 2.10.3 Double pole Each 1 ₹ 556.00 556.00

c 2.10.5 Triple pole and neutral Each 1 ₹ 1,092.00 1,092.00

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual

2.5 2.14 current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Total of DB carried over to summary 0.00 27,540.00

3.0 CABELS / MAINS

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade

of following size in the existing masonry open duct as required.

b 8.4.2 Above 120 sq. mm and upto 400 sq. mm Meter 5 96.00 480.00

Supply of 1100V grade armoured cable having sector / circular shaped aluminium / copper

conductor PVC insulated cores under ground PVC tape wrapped inner sheathed, GI strip /

3.2 wire armoured and overall extruded PVC sheathed confirming to IS: 1554, laid on wall or

ceiling using GI clamps and spacers as per route shown at site and further as directed by

Engineer-in charge

a MR 240 Sq.mm 3 1/2 core Aluminium cable mtr. 2 1,843.75 3,687.49

b MR 70 Sq.mm 3 1/2 core Aluminium cable mtr. 5 628.71 3,143.53

c MR 50 Sq.mm 3 1/2 core Aluminium cable mtr. 10 468.38 4,683.80

d MR 25 Sq.mm 4 core copper cable mtr. 10 2,390.44 23,904.36

e MR 1 6Sq.mm 4 core copper cable mtr. 150 1,099.81 164,972.10

Supplying and making end termination with brass compression gland and aluminium lugs for

3.3 9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Total of Cables / Mains carried over to summary 200,391.29 8,512.00

Point wiring for light point /Fan/Exhaust Fan point/ call bell point using 2 runs of 1100 V grade

1.5 sqmm & one run of 1.5 sq.mm FRLS insulated multistranded copper wires, in & including

4.1 1.3 25 mm dia , MS conduit surface/ concealed in wall / ceiling conferming to IS 732 including all

accessries such as junction boxes , conduit bends, elbows and ceiling rose , and anodised GI

switch box with modular switch ,modular plate and the box covered with front plate

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point

(without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor

single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm

FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

4.3 1.3.3 Exhaust fan point including of ceiling rose near fan. - Primary - Group-C Per Pts 15 1,213.00 18,195.00

Wiring for twin control point wiring using 1.5 sqmm copper conductor FRLS PVC insulated

copper conductor cable drawn through 25 dia MS conduit laid in surface/concealed over

4.4 1.4 false ceiling or in slab/wall chases including ,2way modular switches,modular plate ,suitable Per Pts 10 1,290.00 12,900.00

GI box and earthing the point with 1.5 sqm FRLS PVC insulated copper conductor single core

cable as required

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

box including connections but excluding modular plate etc. as required.

c 1.24.4 3 pin 5/6 A socket outlet Each 50 111.00 5,550.00

d 1.24.5 6 pin 15/16 A socket outlet Each 25 175.00 4,375.00

e 1.24.7 TV antenna socket outlet Each 12 119.00 1,428.00

Supplying and fixing following size/ modules, GI box along with modular base & cover plate

for modular switches in recess etc. as required.

Supplying and fixing following Modular base & cover plate on existing modular metal boxes

etc. as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

4.8 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the Meter 55 33.00 1,815.00

existing surface/ recessed steel/ PVC conduit as required.

4.9 MR Supplying and laying HDMI Cable with connector on both ends. Meter 25 133.91 3,347.63

Supply and fixing of following sizes of MS conduit along with accessories in surface /recess

4.10 1.20 including painting in case of surface conduit,or cutting the wall and making good the same

in case of recessed conduit as required

Total of Wiring carried over to summary 3,347.63 1,348,883.00

SITC of 1'X4' recessed mounted Luminaire with Maximum 36 Watt with Lumen output of 3600

lumen. The product should be SMD based and have non integral isolated driver with 2KV

5.1 MR inbuilt surge protection. THD<10%, PF >0.9,Product should have life class of 50K burning hour Nos. 18 2,943.51 52,983.17

at L70 B50 parameter, Luminiare operating temp 0 D to 45D. Internal wiring should have teflon

coted multi strand wires and external wire should have PVC coated multistrand wires.

SITC of Recessed mouted PDC lowdepth(height should not be more than 35mm) downlights

with maximum 12 Watt with minimum 1320 lumen.The product should be SMD based & have

non integral isolated driver with 2KV inbuilt surge protection. THD<10%, PF >0.9,Product should

have life class of 50K burning hour at L70 B50 parameter, Luminiare operating temp 0 D to

45D. Internal wiring should have teflon coted multi strand wires and external wire should have

PVC coated multistrand wires.

SITC of Extruded Aluminium surface mounted 36Watt, 4000 lumen LED batten with PC Diffuser

and Spring Steel Clamps for Surface Mounting arrangement. Driver THD<15%, PF >0.9,with 2KV

inbuilt surge protection. Internal wiring should have teflon coted multi strand wires and

external wire should have PVC coated multistrand wires.

Supply, Installation, Testing and Commisioning of Suspended /surface/Recessed type linear

Luminaire of size 72mm (N.S.), Linear ultra modular fixture made up of extruded aluminium

housing with luminare efficasy more than 100 LPW, CRI >80, CCT of 5700K. suitable for 220 V,

50 Hz, The luminare rated life (L70) >50000 Hours with High efficiency driver with inbuild surge

protection, over voltage protection, short circuit protection and operating at >0.95 .making

suitable arrangement for fixing including connection with 3 x 1.5 sq.mm. The price shall

include all accessories including jointing kit for uniform continuous lines of light across ceiling

etc complete in all respect

Providing & Fixing Coverings (Ceiling & Wall) Made out of Polyester Kintted fabric Coated with

polyurethane (PU). The Fibric width 2m,3m,4.1m,&5.1m with Weight of 200gm/m^2. thickness

of 0.3mm. The appearance of fabric is Matl. smooth and uniform with blance color and ligth

transmission of 50%. The tear strength of febric should be accordance to CH. 4.5daN; TR: 6.5

daN. The fire Railing should be accordance to B-S1, do. The febric should be humidity

ressistant and free of cercinogenic subtance (CMR) or volatile organic compounds (VOC's).

At lableing in accordance with the French decree no, 2011- 321, Oeko -Tex standar100

certified. The fabric should be paintabe/printable with approved manufacturer guidelines

5.5 MR with 10-year manufacture guarantee. the Installation of fabric should be dry installation Sqm 2 12297.00 24594.00

7done at room tamperature using CLIPSO PVC, ASB tension profiles P.CC/P-C10QS/P-

C11QS/P-CCB022/P-B1/P-CC1P. There are several lighting options available including various

LED options and fluorescent lighting. When Positioned properly. LED Lighting modules provide

an even light flow, casting no shadowns or hot spots. coverings are used for a variety of

aluminated applications, including but not limited to walls, ceiling, lightboxs or wall frames.

coverings can enhance your door with a variety of spacial effects fiber optics or

changinglights, or create a statement piece incorporating custom printing. The cost of

electrical cove light fixtures is included in the same.

Providing & Fixing High Speed 450 mm Wall Fan, complete with all hardware and connectors

etc., as per the direction of the engineer In charge

Providing & Fixing Heavy Duty 4 Blade, 15" Exhuast Fan complete with all hardware and

connectors etc., as per the direction of the engineer In charge

Providing & Fixing Waterproof LED Rope / Cove Light having 400 Lm per meter (72 LEDs per

5.8 MR meter) of any color, , complete with all hardware, connectors, drivers etc. , as per the RMT 125 211.00 26375.00

direction of the engineer In charge.

Total of Light Fixture carried over to summary 277,286.78

6 WIRING FOR DATA AND VOICE OUTLETS

Supply and fixing the following sizes of PVC medium duty ISI marked conduits (IS : 9537 Part-III)

complete with accessories such as bends, junction boxes, pull boxes etc., in recess or on

surface including cutting chases in the walls/floors and making good the same complete as

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/

PVC conduit as required.

Supply & fixing of Plug in type RJ45 computer data outlet in existing faceplate/ GI Box in

wall/furniture/floor complete as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

box including connections but excluding modular plate etc. as required.

a 1.24.6 Telephone socket outlet Each 15 119.00 1,785.00

6.5 Supply and fixing of the following types Face Plates complete with all accessories.

Supply & Fixing of Single Faceplate, Single Port (RJ45-DATA) square plate having spring

a shuttered front access for preventing ingress of dust, dimension as per commercially Nos. 30 95.72 2,871.52

available modular office furniture.

Supply & Fixing of Dual Faceplate, Duplex Port (RJ45 for data ) and (RJ-11 for voice) or as

b. required square plate having spring shuttered front access for preventing ingress of dust, Nos. 15 95.72 1,435.76

dimension as per commercially available modular office furniture.

Supply ,laying ,installing , testing and commmissioning of the 50 pair multi core 0.61 mm

annealed copper conductor PVC insulated and PVC sheathed armoured telephone cables

generally conforming to ITD S/WS-11-C and IS 1554 part I direct in ground /surface and / or in

existing pipe as required and includig making terminal joints, complete as required.

Supplying, installing, testing and commissioning of 24 port Cat 6 patch panels available with

block of four equipped with tool less IO, Rack Mountable. 19" Modular Patch Panel, loaded

CAT6 U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6 X RJ 45 Tool less

connector U/UTP unit in a block.

Supplying, installing, testing and commissioning of Cabinet. Size 24U (800 X 800 mm) (WXD)

following accessories, Width (mm) 800, Depth (mm) 800, Approx.Net Wt (kg) 75, CRCA 'D'

Grade thickness (mm) 1.2, RAL 9017(Matt Black), Glass: 4mm Toughened Tinted Glass

Door,Injected one piece polyurethane gasket on frame, Accessories: Cooling Fan (230V A/C

90 CFM) - 4 Nos, Cable Manager Metal- 4 Nos,PDU 230VAC - 1 No (12 nos. 6A/16A sockets

6.8 with plugs 6A/16A - 1/1pc & MCB 16A/32A -0/1 Pc), cable channel 100mm wide 24U- 2 EACH 1 38,551.38 38,551.38

Nos,Heavy Duty Stationary shelf M6 screws,washer,cage nuts (nickel coated))3 Nos. Earthling

Strips 150mm H - 1 No, Door Lock - 1 No, Castor Wheels (with Brake) - 2 Nos, Castor Wheels

(without Brake) - 2 Nos, Front Metal Band - 1 No. Packing: 5 ply cardboard & Inside 28 ply EP

foam. In the rack there must be maintained 1 U = 1.75 inches space. Nos. 1 etc complete as

6.9 Supply Installation testing and commissioning of 12 Port Loaded LIU multimode each 2 11939.00 23878.00

6.10 Supply Installation testing and commissioning of Fiber patch cord each 2 1978.00 3956.00

6.11 Supply Installation testing and commissioning of multimode fiber optic cable each 15 106.00 1590.00

6.12 Supply Installation testing and commissioning of multimode 10G SFP Modules each 1 15696.00 15696.00

Supply, installation, testing and commissioning of HDMI 4K/60 Receiver with Audio De-

Embedding as per required specifications :Input CATx on RJ 45 port Video Output 1 HDMI

Supply, installation, testing and commissioning of HDMI 4K/60 Transmitter withAudio

Embedding as per required specifications : Input 1 HDMI Video Output CATx on RJ 45 port

6.15 Supply, Installation, Tetsing & Commissoning of POP Box with Manual Rotating system, 2 x each 2 24759 49518.00

Universal Power 2 x USB Charger, 2 x RJ45 Network, 1 x VGA, 1 x 3.5 mm Audio 1 x HDMI 2.0

Total of Data & Voice carried over to summary 207,671.62 98,185.00

7 CABLE TRAY.& RACE WAY.

Supply, fabrication and fixing of steel frame work in position for cable tray/Panels fabricated

out of 10 mm dia GI rods, ISA-40 MS angle iron, ISMC-50 channels, flats etc.complete with

7.1 providing of Anchor fastners and all necessary hardwares as required for fixing, including

cutting, bending, welding, drilling, bolting etc. as per design as required and painted with

one coat of primer and two coats of enamel paint of approved shade.

Supply and fixing of Perforated type 2mm thick Hot dip Galvanised G.I. cable tray of following

sizes complete with bend/tee joints, coupling plate & nuts bolts etc. as required for fixing and

including the cost of providing loop earthing with 2 nos. 50 mm x 6 mm GI earth strips

complete as per specifications, as required and as below.

7.2 GI Raceway & Junction boxes ( Raceway on floor shall be of aluminium only)

Providing and fixing 2 mm thick steel sheet factory fabricated post galvanized raceway with

internal partition/compartmentized of the following sizes including providing removable 3 mm

thick GI cover, knock out holes and fixing accessories earthing with 8 SWG copper earth wire

complete as required including floor supports, bends, access boxes, tap off boxes and cross

over as per specification and site requirement. (overhead / wall mounted recovery & function

boxes shall be 1.6 mm thick)

a) 300 mm wide x 38 mm deep raceway RM 5 2,203.66 11,018.30

b) 225 mm wide x 38 mm deep raceway RM 7 1,868.27 13,077.88

c) 150 mm wide x 38 mm deep raceway RM 15 1,380.22 20,703.25

d) 100 mm wide x 38 mm deep raceway RM 15 1,062.17 15,932.59

Providing and fixing 350 x 350 x 60 mm deep 2 mm thick GI sheet junction box including

providing 3 mm thick stainless steel cover as per specification.

Providing and fixing 150 x 150 x 60 mm deep 1.6 mm thick GI sheet junction box including

providing 3 mm thick stainless steel cover as per specification.

Total of Raceway carried over to summary 103,171.36 37,460.00

Reno 2018 Description Unit Qty Rate Amount

8 IP BASED CCTV SYSTEM

Supply and fixing of following sizes of MS conduit along with accessories in surface

8.1 1.20 /recess including painting in case of surface conduit,or cutting the wall and

making good the same in case of recessed conduit as required

Supply, installation, testing and commissioning of 2MP 2.8mm/3.6mm wide angle

fixed lens IR Dome Camera 1/3" Progressive Scan CMOS;

8.2 MR H.265+/H.265/H.264+/H.264/MJPEG; Colour: 0.01 lux @(F1.2, AGC ON), 0 lux with IR; Nos. 8 9,009.02 72,072.16

25fps/30fps(2560×1440, 1920×1080); 3 VCA functions; 3 streams; 3D DNR; ICR; EXIR

2.0, up to 30m; DC12V&PoE; Built-in micro SD/SDHC/SDXC slot.

Supply, installation testing and commissioning of Network Video recorder Linux

based to manage and control all the cameras from control room. Software shall

8.3 MR support maximum 32 channel with joystick controller. 256Mbps Bit Rate Input Nos. 1 63,875.45 63,875.45

Max(up to 32-ch IP video), 4 SATA Interfaces, alarm I/O: 16/4, 1.5U case,19" with

4x6TB i.e. 24TB HDD inside

Supply, installation, testing and commissioning of Video Management software

enabling security related personnel to easily and remotely gather video evidence,

monitor live situations, and configure and maintain a video surveillance system

over Ethernet consisting of digital video recorders (DVRs), hybrid digital video

8.4 MR recorders, network video recorders (NVRs), analogue video cameras, and IP video Nos. 1 24,748.14 24,748.14

cameras should support Detachable Viewers –users have the ability to detach

Viewer panels and move them to other (or the same) monitor(s). A maximum of

two (2) Viewers can be detached for a total of 75-up video tiles [two (2) detached

and one (1) core Viewer.

Supply Installation Testing & Commissioning of 21 inch Full HD LED monitor including

wall mount brackets/ clamps/ desk mounting stand.

8.6 MR Supply and fixing of RJ45 Connector Nos. 8 274.02 2,192.17

Supplying and fixing in position GI box for data outlet suitable for fixing of RJ 45

face plate complete as required.

Supply & Fixing of PCB based Information Outlet (I/O) RJ45, TIA-568C Category-6,

Termination of Catergory-6 UTP Cable, UL listed, Shall conform to Category-6 as

per the EIA/TIA-568C.2, Shall support network line speeds up to 1 Gbps, Shall have

RJ-45 type connector with bend limiting and strain relief boot for securing IDC

8.80 MR contacts from external forces and for maintaining the bend radius of the cable, Nos. 8 174.17 1,393.40

Shall have minimum durability of 750 mating cycles and 200 termination cycles.

Shall be certified by independent labs like ETL/GHMT for compliance to EIA/TIA-

568C.2. The outlet shall be fixed in existing box & cover plate in wall/furniture/floor

complete as required.

Supply & Fixing of Single Faceplate, Single Port (RJ45-DATA) square plate having

8.90 MR spring shuttered front access for preventing ingress of dust, dimension as per Nos. 8 95.72 765.74

commercially available modular office furniture.

Supply, installation, testing and commissioning of Rack 12U with all accessories viz 4

8.10 MR Nos of mounting hardware, fan tray, power strip and cable manager as required Nos. 1 3,363.37 3,363.37

Supply & Laying in existing conduits/raceway/furniture of 4-pair Unshielded twisted

pair cable with a cross filler (+), meeting Category 6 standards as per TIA-568C.2.

8.11 MR The cable shall be tested till 600 MHz or more from independent laboratories like RM 145 58.37 8,463.69

ETL for 4 connections. Test Certificate from independent labs like ETL shall be

Supply & Fixing of UTP Jack Panel UL listed, loaded with 24 no's UTP ports for PCB

based IO Jacks (RJ45, TIA-568C Category-6), having integrated bonding bar or

other mechanism for grounding, loaded with individually replaceable 24 nos.

8.12 MR Category-6 I/O Jacks complying with TIA-568.C.2. Shall be 6 port module Nos 1 1,801.80 1,801.80

construction for better cable dressing at the rear. The jacks shall have RJ-45 type

connector with bend limiting and strain relief boot for securing IDC contacts from

external forces and for maintaining the bend radius of the cable.

Supplying & Fixing of Category 6, UTP patch cords constructed of 24 AWG

unshielded twisted pair stranded copper cable with an enhanced performance

modular plug at each end. Patch cord cable shall be offered in multiple coloured

UTP cable for design flexibility with a clear strain relief boot on each modular plug.

All patch cords shall be compatible with both T568A and T568B wiring schemes.

UTP Cable, 2 Meter.

Supplying & Fixing of Category 6, UTP patch cords constructed of 24 AWG

unshielded twisted pair stranded copper cable with an enhanced performance

modular plug at each end. Patch cord cable shall be offered in multiple coloured

UTP cable for design flexibility with a clear strain relief boot on each modular plug.

All patch cords shall be compatible with both T568A and T568B wiring schemes.

UTP Cable, 1 Meter.

Supply Installation Testing & Commissioning of Managed Layer -2 Switch with Power

8.15 MR on Ethernet (PoE) enabled, 24 Port Fast Ethernet Web Smart Switch, including 2 Nos 1 10,210.22 10,210.22

Gigabit BASE-T and 2 Gigabit Combo BASE-T/SFP.

TOTAL OF IP BASED CCTV SYSTEM CARRIED OVER TO SUMMARY Rs. 245,997.66

20 kVA UPS with 15 minute backup

Supply, unloading, shifting, installation, testing & commissioning of micro processor

controlled following rating UPS capable of operating in parallel redundant mode

so that if any one UPS fails the other can supply 100% load, IGBT based rectifier to

achieve input THDI < 4% and input power factor of greater than 0.99 at 100%

loading with 3 level Inverter Topology. True Online Double Conversion (VFI as per

IEC 62040-3) UPS using PWM IGBT technology , 3 Phase input and 3 phase 415 V

output UPS system; and comprising of the following complete as required and as

per specification:

Fully rated Rectifier cum charger unit and 100% rated Invertor unit Integrated in UPS

Fully rated Inbuilt static switch at the inverter output and 100% rated Inbuilt static

switch at the static bypass line integrated in UPS module.

Web-enabled Monitoring and Management through SNMP protocols for multi-OS

environments with below features.

Giving notifications like e-mail, paging notification, broadcast notification, battery

replacement notification, run event-based scripts.

Event logging, data logging and action logging (with date, time, description of

fault and event).

Fully rated Inbuilt Maintenance Bypass Switch for the continuous operation of the

load during maintanance.

Local notification through audible alarm.

Fully rated Battery Circuit Breaker with under voltage coil & deep discharge

protection to the batteries.

One time cost of replacement of PCBs to be considered, in case conformal

coated PCBs are not available .

(Vendor to specify the cost considered)

Battery Banks comprising of Valve Regulated Lead Acid Sealed Maintenance Free

batteries of minimum 5years design life to provide 15 minutes backup at 20kVA

,0.9PF, ECV=1.7V with each UPS. Minimum VAH required with each UPS 11232 VAH

.The batteries shall be installed on shelves of rack for quick replacement and

servicing. The temperature sensor shall be provided in the battery section for

temperature compensated charging. The bank of batteries shall comprise of

required numbers of batteries connected in series.

Vendor to provide complete details of make of Batteries, ampere hour ratings, no.

of Batteries, Expected life, Final discharge voltage, Nominal float voltage, Battery

recharge time & configuration of back up time, Battery sizing Calculations

Supply, unloading, installation, testing & commissioning of open type MS racks

including top fully cover to protect from falling object to house SMF batteries for 30

kVA UPS system along with suitable interconnecting links, moulded case circuit

breaker having Ithermal, Imagnetic & automatic U/V trip mechanics for Battery

Banks etc. complete as required & as per specifications.

UPS Testing with External Load Banks (To be provided by vendor) for 8 hours at full

load shall be included in the offer incase Phantom Loading feature as specified in

the data sheet is not available in the UPS.

Supply, laying, testing & commissioning of flexible single core copper cable for

interconnections between UPS to UPS, UPS to batteries( 10 m) , complete as

required for each UPS.

TOTAL OF UPS & INVERTER SYSTEM CARRIED OVER TO SUMMARY Rs. 503,183.78

10 EPBAX System

Supply, installation, testing and commissioning of digital / ip based epabx system in

simplex mode and all cards hot swappable and expandable upto 1000 ports and

with all features as per technical specifications along with hardware for the

a.124 analog extensions

b. 20 NOS. digital extensions

c. 16 NOS. analog trunk

d.1 no isdn pri (30 channels)

10.1 MR f.built in least cost routing Nos. 1 362743.66 362743.66

g.snmp based system administration

H.SUPPORTS H-320 PROTOCOL FOR VIDEO CONFERENCING BEHIND EPABX

i.supports dect connectivity - digital cordless extension

j.lan connectivity

k.music on hold

l..voice mail for all users

m. Online 2KVA UPS dedicated for EPABX System

Supply,installation and commissioning of digital phones with the following features

i) tiltable graphical display, 2 lines monochrome keys

ii) Programmable key

10.2 MR iii) 3 way navigator Nos 5 20725.78 103628.89

iv) 7 fixed function keys

v) hands free talking

with built in speaker complete

10.3 MR Supply, installation and commissioning of desktop analog telephone complete Nos 15 599.90 8998.57

TOTAL OF EPBAX Rs. 475371.12

Project : JEEVAN TARA BUILDING

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

11 SITC OF FIRE ALARM AND PA MR. DSR.

DSR Total Total

Sr. No Description Unit Qty Unit Rate

2018.No. amount amount

Supplying, installation, testing and commissioning of micro processor based intelligent addressable main

fire alarm panel, central processing unit with the following loop modules and capable of supporting not

less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2

km, network communication card, minimum 320 character graphics/ LCD display with touch screen or

other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply

unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic

charger. The panel shall have facility to connect printer to printout log and facility to have seamless

integration with analog/digital voice evacuation system (which is part of the schedule of work under SH:

PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system

with open protocol BACnet/ Modbus over IP complete as per specifications.

Two Loop Panel. Pcs 1 238907.00

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector Pcs 20 2846.00

complete with mounting base complete as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of Pcs 2 2713.00

rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required. Pcs 6 3859.00

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. Pcs 10 3494.00

Supplying, installation, testing & commissioning of fault isolator complete with base as required. Pcs 2 3257.00

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having Pcs 15 263.00

two LED, metallic cover complete with all connections etc as required.

CABLES & ACCESSORIES FOR FAS :

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper RM 95 141.00

11.8 17.5.2 conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. 13395.00

SITC OF PUBLIC ADDRESSABLE SYSTEM & ACCESSORIES :

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player Pcs 1 126399.00

11.9 17.3.1 (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for 126399.00

voice evacuation complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at Pcs 1 96767.00

240 volt AC supply complete as required.

Supplying, installation, testing & commissioning ofceiling/wall mounted loud speaker, 3/1.5 Watt in ABS Pcs 10 2416.00

enclosure complete as required.

CABLE & ACCESSORIES FOR PA SYSTEM

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing

11.12 17.5.3 surface / recessed steel conduit of following pairs, cores and size including connections and

interconnections etc. as required..

17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm RM 95 51.00 4845.00

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and RM 45 50.00

accessories like coupler etc. as required.

BOQ - Fire ALarm PA system

Electrical Consultant : DCS Consultant Sons

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

Sr. No Description Unit Qty Rate Amount

12 ACCESS CONTROL SYSTEM

Supply, Installation, Testing & Commissioning of Access Control System

with RFID, Figure Print and Pin Authenication with 3,000 Fingure Print

12.1 Capacity, 10,000 Card Capacity, 50,000 Transaction Log Capacity, Built Nos. 1 49,680.54 49,680.54

In Buzzer, 128X64 OLED Display, 3x5 Keypad and Bells, Weigand Output,

USB, TCP/IP Network Interface, IP 65 Weatherproof.

Supply, Installation, Testing & Commissioning of 2 Door/ 2 Reader IP

Controller accommodates a card database of 55,000 cards, and a

transaction buffer of 45,000 transactions,TCP/IP, USB, Serial Interface unit,

Relay Switching Port.

12.3 Supply, Installation, Testing & Commissioning of Proximity Cards. Nos. 20 311.83 6,236.64

Supply, Installation, Testing & Commissioning of Electromagnetic Lock

12.4 600 lbs, single leaf, LED Status Display, includes Door Sensor, i/c making Nos. 2 2,806.49 5,612.98

conection, integration, testing etc. complete as required on site

Supply, Installation, Testing & Commissioning of Power Supply 12V 2 A for

12.5 Access Control Reader and Door Lock Unit, Complete in all respect as Nos. 2 3,160.84 6,321.69

required at site.

Supply, Installation, Testing & Commissioning of Alagtech U/L Clamp

made of aluminium anodised for EM Lock on the surface of

frame/structure etc. i/c alignment etc. for smooth operation of EM lock

Supply, Installation, Testing & Commissioning of 24 Port Gigabit Switch,

12.7 Auto MDI-MDIX for all port,Link Status Detection, 4.8 Gbps Switching Nos. 1 36,073.32 36,073.32

Capacity, Rack Mountable, Complete in all Respect as required at site.

Supply, Installation, Testing & Commissioning of Access Control Software

for with Advance Access Management Module & Advance Attandence

12.8 Mangement Module. It should support Multi company, Multi location, Nos. 1 123,740.69 123,740.69

Multi department, Multi login with different rights, Muti hierarchy of

Total of Access Control System carried over to summary 288,430.61

S.No Item SITC of the Folowing Items / Works UoM Unit Cost (INR) Qty.

65" Full HD LED display, HDMI X 2, VGA X 1, Video IN X 1, USB X 1, Audio IN X1, Audio Out X 1,

13.1 LED Display SPDIF X 1, RS232C x 1, 20W in built speaker, IPS LED display, USB media player NOS 197,691 1 197,691

55" Full HD LED display, HDMI X 2, VGA X 1, Video IN X 1, USB X 1, Audio IN X1, Audio Out X 1,

13.2 LED Display SPDIF X 1, RS232C x 1, 20W in built speaker, IPS LED display, USB media player NOS 117,486 1 117,486

13.3 Wall mount Braclet Wall Mount bracket for suspension of LED Display NOS 8,919 2 17,837

Table Top Cable Manager { With 1xHDMI,1xVGA,1XAux,1xData,1X Voice, 2xUniversal Power

13.4 Cable Manager NOS 16,106 2 32,211

Socket and two USB Chargers.

"Communication Method: SIP, H.323 Video Compression Method: H.261 (mainstream) H.263,

H263+, H.263++ (reception only), H.264 High Profile, H.264 Baseline Profile

No. of Channels: G.711/G.722/G.722.1/G.722.1 Annex C: 1 MPEG-4 AAC-LD Mono: 1/ MPEG-4

Video Conference

13.5 AAC-LD Stereo: 2 Remote Camera Control: H.224, H.281 (Zoom/Pan/Tilt/Preset) NOS 664,417 1 664,417

Encryption: SRTP (AES 128 bit), H.235 (AES 128 bit)"RealPresence Group 500-720p: Group 500

HD codec, EagleEyeIV-12x camera, mic array, univ. remote, NTSC/PAL. Cables: 2 HDMI 1.8m,

1 CAT 5E LAN 3.6m, 1 HDCI digital 3m, Power: India BIS. Maintenance Contract Required

Multi Point Video

13.6 Conferencing 4-way HD continuous presence. NOS 181,353 1 181,353

Total Amount 1,210,995

Total Amount 1,210,995

BILL OF QUANTITIES (BOQ)

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

Plumbing and fire fighting sub head

DESCRIPTION S.I (AMOUNT) N.S.I (AMOUNT)

A SANITARY FIXTURES & FITTINGS 177834.43

B WATER SUPPLY 36856.55 0.00

C INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES) 36856.55 0.00

D SPRINKLER PIPING & ACCESSORIES 120318 43334.95

Total Cost ( Carried Forward) in Rs. 415,200.49

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

SUB HEAD A: SANITARY FIXTURES & FITTINGS

DSR Rate NS Rate DSR -

SL. NO. DESCRIPTION OF ITEMS UNIT Qty Amount NS Amount (Rs)

1.1 Providing & fixing glazed vitreous china single trap syphonic

pattern having back inlet ,supporting chair ,wall hung water

closet with cistern complete with all internal

fittings/accessories and CP brass flush bend (European type)

water closet with seat and lid, with C.P. brass hinges and

rubber buffers, adapter, rubber joints fixed to W.C., C.P.

brass screwed washers including cutting and making good

the walls and floors wherever required and HDPE wc pan

connector including jointing with white cement coomplete

in all respects

Wall hung W.C. pan (White colour)with white plastic seat &

lid "Thermoset moulded ( bakelite ) IS 2548 Part I

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 19951.19 39902.39

1.2 Providing & fixing glazed vitreous china wash basin with R.S.

or C.I. brackets painted white, 32mm C.P. brass waste of

standard pattern , C.P brass wall flange 32 mm dia. C.P.

brass bottle trap and union 32 mm dia C.P. pipes to wall

flange. complete including cutting and making good the

walls wherever required. NS

Undercounter wash basin (White colour)of size: 585x430 mm

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 8077.16 16154.31

1.2.2 Table top wash basin (white colour)of size: 440x440 mm NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 1 10434.84 10434.84

1.3 Providing & fixing 15mm C.P. brass single hole wash basin

mixer without popup waste system with 450mm long copper

pipes and brass nut NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 3678.73 7357.47

1.4 Providing & fixing vitreous chinaware urinal comprising NS

Large flat back wall hung urinal in glazed vitreous China new

magnum urinal NS

15 mm electrically operated solenoid valve with infra red

sensor mounted in a box with SS Cover.

CP brass chromium plated flush piping from solenoid valve

to urinal terminated with a 15 mm screwed spreader

32 mm nominal bore CP cast brass waste

32 mm nominal bore CP cast bottle trap with extension pipe

rubber adopter for waste connection, CP brass wall flange.

For supply,installation,testing & commissioning of sanitary

fixtures(white colour) as per above details. Each 1 28082.91 28082.91

1.5 Providing & fixing stainless steel sink R.S. or C.I. brackets

painted, 40mm C.P. waste, C.P. brass chain and rubber

plug, 40mm C.P. cast brass bottle with necessary union

complete including cutting and making good the walls

wherever required NS

Stainless steel sink single bowl with drain board(size

510x1040mm) of approved

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 1 11933.04 11933.04

1.6 Providing & fixing Sink Mixer with Swinging Casted Spout

(Wall Mounted Model) with 450mm long Copper Pipes &

Brass Nuts.CP brass wall flange NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 1 3694.17 3694.17

1.7 Providing & fixing toilet paper holding including cutting and

making good the walls. NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 1672.39 3344.78

1.8 Providing & fixing Horizontal liquid soap dispenser with

stainless steel lid and brackets fixed to wooden cleats with

C.P. brass screws. NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 3579.33 7158.65

1.9 Providing & fixing C.P. brass coat hooks fixed on toilet door

with C.P. brass screws NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 605.30 1210.60

1.10 Providing & fixing beveled edge mirror 5.5mm thick of

superior quality plate glass complete with 6mm thick marine

ply sheet ground fixed to wooden cleats with CP brass

screws and washerswith 40 mm wide teak wood frame as

per design including polishing NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Sqm 2 2342.67 4685.34

Providing & fixing Hand Shower (Health Faucet) with 8mm

dia, 1M long PVC tube and wall hook CP brass wall flange NS

For supply of sanitary fixtures as per above details Each 2 1730.56 3461.13

1.12 Providing & fixing, testing and commissioning of storage type

electric water heater with automatic thermostatic control

electric element, pressure release valve, brackets fixed to

expansion fasteners with M.S. nuts and bolts all complete

including cutting and making good the walls wherever

25 litres capacity (Horizontal /Vertical type1.5 kw electrical

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 1 19015.73 19015.73

1.13 Providing & fixing wall mounted 25 mm dia Stainless steel

coated grab bar including cutting & making good the

walls(size 450mm long) NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 912.33 1824.65

1.14 Providing & fixing 15 mm dia C.P. brass bib cock with Hose

union of approved quality. NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 1282.79 2565.58

1.15 Providing & fixing 15 mm dia C.P. brass bib cock with C.P.

wall flange of approved quality. NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 1566.66 3133.32

1.16 FRAGRANCE DISPENSER MACHINE :-Providing and fixing of

Fragrance Dispenser machine complete with refill can and

'C' size battery (2 Nos) for operation fixed to wooden cleats

with CP brass screws NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 4534.90 9069.80

1.17 Providing and fixing of stainless steel finish Paper Towel

Dispenser having capacity of 300-350 paper towels fixed to

wooden cleats with C.P. brass screws NS

For supply,installation,testing & commissioning of sanitary

fixtures as per above details. Each 2 2402.86 4805.73

i. Detail of Sanitary fixture are for the information of the

Contractor,however model/makes of all sanitary fixtures shall

be selected by Architect/Interior designer/Project manager

and the same shall be binding for execution.

ii. No additional fixing cost shall be paid for change in type of

sanitary fixtures.

iii. Contractor to receive all the above mentioned items & store

at place as directed at site.

TOTAL CARRIED OVER TO SUMMARY 177834.43

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

SL. DSR Rate NS Rate DSR -

DESCRIPTION OF ITEMS UNIT Qty Amount Amount

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

(CPVC) plain & brass threaded fittings including fixing the pipe

with clamps at 1.00 m spacing. This including jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints

complete as per direction of engineer in charge. .

Internal Work - Exposed on Wall

20 mm nominal outer dia pipes. Metre 15.00 325.10 4876.50 18.7.2

25 mm nominal outer dia pipes. Metre 15.00 408.55 6128.25 18.7.3

32 mm nominal outer dia pipes. Metre 5.00 500.95 2504.75 18.7.4

40 mm nominal outer dia pipes. Metre 5.00 674.35 3371.75 18.7.5

50 mm nominal outer dia pipes. Metre 2.00 927.00 1854.00 18.7.6

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings i/c fixing the pipe with

clamps at 1.00 m spacing. This including jointing of pipes & fittings

with one step CPVC solvent cement and the cost of cutting

chases and making good the the same including testing of joints

complete as per direction of engineer in charge.

Concealed work oncluding cutting chases and making good the

20 mm nominal outer dia pipes. Metre 15.00 513.75 7706.25 18.8.2

Providing and fixing brass stop cock of approved quality

2.3 complete. 18.16

20 mm nominal bore Each 5.00 327.95 1639.75 18.16.2

Providing and fixing gun metal gate valve with C.I. wheel of

2.4 approved quality (screwed end): 18.17

25 mm nominal bore Each 2.00 532.35 1064.70 18.17.1

32 mm nominal bore Each 2.00 588.90 1177.80 18.17.2

40 mm nominal bore Each 2.00 707.30 1414.60 18.17.3

Providing and fixing C.P. bass angle valve for basin mixer and

geyser points of approved quality conforming to I.S:8931 a) 15

2.5 mm nominal bore. 18.53

15 mm nominal bore Each 2.00 500.35 1000.70 18.53.1

Providing and fixing unplasticised P.V.C connection pipe with

PTMT Nuts coller and bush of approved quality and colour.

15mm nominal bore with 45cm length Each 10.00 107.90 1079.00 18.74.2

Sub-Total of Water Supply Installation, Separate for Scheduled & Non-Scheduled Items 36856.55

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

SL. DSR Rate NS Rate NS Amount DSR -

DESCRIPTION OF ITEMS UNIT Qty DSR Amount (Rs)

Providing and fixing cast iron trap of self cleansing design with cast

iron screwed down or hinged grating with or without vent arm

complete, including cost of cutting and making good the walls and

100 mm inlet and 100 mm outlet centrifugally cast (spun) iron S&S as

3.2 Providing and fixing soil, waste and vent pipes. 17.35

Centrifugally cast (spun) iron S&S pipe as per IS 3989.

100mm dia cast (spun) iron S&S pipe Metre 15 1,077.40 16,161.00 17.35.1.2

Centrifugally cast (spun) iron S&S pipe as per IS 3989.

75mm dia cast (spun) iron S&S pipe Metre 5 1,042.10 5,210.50 17.35.2.2

Providing and fixing single equal plain junction of reqd. degree with

access door, insertion rubber washer 3mm thick, bolts and nuts

3.3 complete. 17.43

Sand cast (spun) iron pipe IS-3989 Each 4 731.40 2,925.60 17.43.1.2

Sand cast (spun) iron pipe IS-3989 Each 2 573.80 1,147.60 17.43.2.2

Providing and fixing single equal plain junction of reqd. degree.

Sand cast (spun) iron pipe IS-3989 Each 4 707.30 2,829.20 17.44.1.2

Sand cast (spun) iron pipe IS-3989 Each 2 498.90 997.80 17.44.2.2

Providing and fixing bend of required degree with access door,

3.5 insertion rubber washer 3mm thick, bolts and nuts complete. 17.38

Sand cast (spun) iron pipe S&S as per IS 3989. Each 2 597.60 1,195.20 17.38.1.2

Sand cast (spun) iron pipe S&S as per IS 3989. Each 2 453.40 906.80 17.38.2.2

3.6 Providing and fixing bend of required degree . 17.39

Sand cast (spun) iron pipe S&S as per IS 3989. Each 4 439.75 1,759.00 17.39.1.2

Sand cast (spun) iron pipe S&S as per IS 3989. Each 2 298.20 596.40 17.39.2.2

3.7 Providing and fixing collar. 17.57

Sand cast (spun) iron pipe S&S IS-3989 Each 2 439.75 879.50 17.57.1.2

Sand cast (spun) iron pipe S&S IS-3989 Each 2 271.45 542.90 17.57.2.2

Providing and fixing MS holder bat clamps of approved design to cast

iron (spun) pipe embedded in and Including cement concrete blocks

10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone

aggregate 20mm nominal size) including cost of cutting holes and

3.8 making good the walls etc. 17.37

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse

sand: 10 graded stone aggregate 40 mm nominal size) alround SW

3.9 including bed concrete as per standard design. 19.2

Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps.

3.10 including cutting and making good the walls etc. 18.10

32 mm nominal bore Metre 5 563.60 2,818.00 18.10.4

40 mm nominal bore Metre 4 725.15 2,900.60 18.10.5

50 mm nominal bore Metre 2 893.20 1,786.40 18.10.6

Painting G.I. Pipes and fittings with two coats of anticorrosive

3.11 bitumastic paint of approved quality 18.40

32 mm nominal bore Metre 5 18.40 92.00 18.40.4

40 mm nominal bore Metre 4 20.95 83.80 18.40.5

50 mm nominal bore Metre 2 25.25 50.50 18.40.6

Painting sand cast iron / centrifugally cast iron( spun) iron soil, waste

and vent pipes and fittings with paint of any colour such as

chocolate, grey or buff etc. over a coat of primer (of approval

3.12 quality) for new work 17.65

100mm dia cast (spun) iron S&S pipe Metre 5 69.55 347.75 17.65.1

75mm dia cast (spun) iron S&S pipe Metre 2 52.90 105.80 17.65.2

Providing lead caulked joints to sand cast iron/centrifugally

3.13 cast(spun) iron pipes & fittings of diameter :. 17.58

Providing & filling the joints with spun yarn,cement slurry & cement

3.14 mortar 1:2(1 cement: 2 fine sand) in SCI/CI pipes. 17.36

Providing and fixing single unequal plain junction of reqd. degree.

Sand cast (spun) iron pipe IS-3989 Each 2 841.10 1,682.20 17.48.1.2

Sub-Total of Drainage Installation, Separate for Scheduled & Non-Scheduled Items 77903.45 0.00

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

DESCRIPTION OF ITEMS DSR

DSR Rate NS Rate NS Amount DSR -

SL. NO. UNIT Qty Amount

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming

to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts

4.1 bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of synthetic enamel paint of required

shade complete as required : 7

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with

4.2 bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets

conforming to IS 13095 of following sizes as required : 11

Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all

accessories as per manufacturer's specifications.

CO2 gas nozzle type - 9 Litre capacity (IS:15683). NOS 2 13,682 27363.01

ABC dry powder stored pressure type 6 kg capacity (IS:15683). NOS 2 1,812 3623.88

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers

of rating 68 degree centigrade with required accessories :

4.4.1 Pendent Sprinkler NOS. 15 484 7260 21.1

4.4.2 Uprigth Sprinkler NOS. 15 484 7260 21.2

4.4.3 Horizontal side wall sprinkler NOS. 5 579 2895 21.3

4.4.4 Concealed Sprinkler NOS. 15 1397 20955 21.4

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of

stainless steel complete with 15 NPT on reducer thread with maximum working

pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT

male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple,

2 side brackets, center bracket, stockbar of following sizes complete as required.

Providing and fixing signages printed on photoluminescent U1000 aluminium sheet of

1.0 mm (+ -10%) containing lumigen II as base chemical, covered under UV stablized

4.5 coating and of appropriate size including fixing on wall, door, ceiling etc. with proper

clamps, hangers, cleats anchor fasteners etc. complete in all respacts as diercted by

Engineer-in-charge SQ INCH 10 30 300 NS

Providing, jointing and testing of automaticaly operated Halotron fire

4.6 extinguishers(cap-5kg,temperature rating-68degc,test pressure-30bar) complete with

all accessories/fittings. NOS. 1 12,048 12048.06237 NS

TOTAL CARRIED TO SUMMARY 120318 43334.95424

Interior/ Renovation work of GOAF Office space at GF, NSIC Technical Service Center, Ohkla, New Delhi

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount NDSR Amount

Supply Installation, Testing & Commissioning of modular

type Variable Refrigerant Flow/ Variable Refrigerant

Volume air cooled Outdoor units suitable for cooling and

heating, having all hermetically sealed inverter type Scroll

Compressor(s), minimum two compressors for above 14 HP

modules, microprocessor based Controller, top discharge

type condensing unit(s), with R410A Refrigerant, vibration

1.1 isolators, with suitable foundation etc. complete as Per HP 28 16415 459,620.00

required.The unit shall deliver the rated capacity at AHRI

Conditions and work even at 50°C ambient temperature

without tripping.The unit shall be suitable to work on

400V+/-10%, 3 Phase, 50Hz AC power supply.The unit shall

be filled with first charge of the refrigerant and ready for

use as required.The COP at AHRI conditions shall not be

less than 3.1 and IEER not less than 6.5 .

2.0 INDOOR UNIT

Supply, installation, testing and commissioning of following

minimum capacity 4-wayflow VRV/ VRF Cassette Type

Indoor ceiling mounted unit equipped with synthetic

washable media pre-filter, fan section with low noise fan/

dynamically balanced blower, multi speed motor, coil

section with DX Copper coil, electronic expansion valve,

outer cabinet, drain pump, grill, necessary supports,

vibration isolation, cordless remote control etc., suitable for

operation on single phase 230V±10%, 50 HzAC supply,

complete, as required. The unit shall have automatic force

shut down provision in case of fire on receiving signal from

BMS System. The cooling capacity of indoor unit will be at

air inl et conditions of 27 Degree CD Band 19 Degree CWB

4-Way Cassette type

3.0 REFRIGERANT PIPING

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal

sizes of soft/hard drawn copper refrigerant piping for

VRV/VRF system, complete with fittings, with suitable

DSR 2019 adjustable ring type hanger supports, jointing/brazing

VRF/VRV including accessories, insulated with XPLE Class-O tubular

insulation/with Class-O closed cell elastometric

nitrile rubber tubular sleeves sections of specified thickness

as given below for Suction and Liquid lines, all accessories

as per specifications etc. as required :

3.1 5.10 34.9 mm O.D (wall Thickness-1.2 mm) (Insulation: 19 mm) Rmt 30 1230.0 36900

3.2 5.8 28.6 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) Rmt 30 1108.0 33240

3.3 5.6 22.2 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) Rmt 50 865.0 43250

3.4 5.5 19.1 mm O.D (wall Thickness-1.0 mm) (insulation : 19 mm) Rmt 50 707.0 35350

3.5 5.4 15.9 mm O.D (wall Thickness-1.0 mm) (insulation : 13 mm) Rmt 76 588.0 44688

Supplying and installing of following size of perforated hot

dip galvanized G.I cable tray with perforations not more

than 17.5%, in convenient sections, joined with connectors,

suspended from ceiling with G.I suspenders including bolts

4 MR and nuts, etc. for carrying refrigerant pipe in outdoor

application as required.

4.1 450 mm width x 62.5 mm depth x 2 mm thickness Rmt 45 1,112 50050

4.2 225mm width x 50 mm depth x 1.6 mm thickness Rmt 10 716 7165

5 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC

Pipe ,complete with fittings, supports,U trap

arrangement,Clean Plug with 6mm nitrile insulation and

accessories as per specifications, drawings.

6 MR Imported fittings Y-joints and headers etc. Nos 10 4281 42814.00504

Providing and fixing control cum transmission wiring of 2

7 MR core x 1.0 sq. mm copper in suitable conduits between Mtr 142.00 161.56 22941.35

indoor and outdoor unit.

SITC of 1.0 T split with rotary compressor of 5 Star rating

Inverter technology approved make make inclusive of 5

8 MR year warranty on compressor all complete. (Note- Indoor Nos. 2.00 44553.32 89106.65

and outdoor unit should have copper Condensor and

9 MR Timer for Split ac for Server Nos. 1.00 3810.71 3810.71

Providing and fixing MS Stand for ODU along with vibration

pad as per approved drawing.

SITC of 3.0 TR Cassete AC with rotary compressor of 5 Star

rating Inverter technology approved make make inclusive

11 MR of 5 year warranty on compressor all complete. (Note- Each 1 128939.00 128939.00

Indoor and outdoor unit should have copper Condensor

and cooling coil.)

SITC of 2.1 TR Cassete AC with rotary compressor of 5 Star

rating Inverter technology approved make make inclusive

12 MR of 5 year warranty on compressor all omplete. (Note- Each 1 97557.00 97557.00

Indoor and outdoor unit should have copper Condensor

and cooling coil.)

SITC of 1.5 TR Cassete AC with rotary compressor of 5 Star

rating Inverter technology approved make make inclusive

13 MR of 5 year warranty on compressor all complete. (Note- Each 1 79956.00 79956.00

Indoor and outdoor unit should have copper Condensor

and cooling coil.)

Supply Installation testing and commissioning of

14 MR CONDENSATE DRAIN PUMPS’ for taking care of water Each 1 6072 6072

drainage of Split ACs

Total Amount 986,935.00 625,568.63

Total Amount 986,935.00 625,568.63