Development of Vallalar International Centre (VIC) in ThiruArutprakasa Vallalar Deiva Nilayam, Vadalur, Kurinjipadi Taluk, Cuddalore District.

Amount

EXCAVATION AND FILLING WORKS

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. - Earth work excavation for foundation in all soils and sub-soils.upto 2m Depth

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered,rammed & consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with Sand Gravel mix in ratio of 1:1 in layers of not more than 15 cm thick thoroughly mixed, well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 0.5m thick well rammed, watered and consolidated etc. complete complying with standard specification

PLAIN CEMENT CONCRETE WORKS

Cement Concrete 1:5:10 (One cement, Five sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for foundation including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers

CENTERING/SHUTTERING WORKS

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid) (Side Shuttering)-Footing, Pedestal Coloumn , Grade beam , Basement coloumn and Plinth beam .

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

centering for Column

centring for beam , lintel, staircase , slab

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.9 Arches, domes, vaults up to 6 m span

Providing additional strutting to centring of RCC slabs of plain surface for every additional 1.0 m height or part there of but not less than 30 cm , over the innitial 3.29 m height from floor level using casurina props of 10 cm to 13 cm dia including cross brasings etc., complete complying with standard specification and as directed by the department officers

ADDITIONAL HEIGHT -0 .7 M

FROM 3.3 TO 4.5 - ADDITIONAL HEIGHT -1.2 M

ADITIONAL HEIGHT-(4.8-3.3=1.5 M)

ADDITIONAL HEIGHT ( 5-3.3=1.7 M)

ADITIONAL HEIGHT-(7.55-3.3=4.25 M)

ADDITIONAL HEIGHT (9.85 - 3.3= 6.55 M )

REINFORCED CEMENT CONCRETE WORKS

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and basement

Ground Floor

first floor

second floor

Providing and laying in position, standardised concrete Mix M-35 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 k9. of 20mm machine crushed stone jelly and with about (3'3 cu'm') 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg' of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Post Tensioning RCC Works & Dome RCC Work

STEEL REINFORCEMENT WORKS

Suppling fabricating and placing in position of mild steel / Ribbed tor steel for all RCC work as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire).complete complying with relevant standard specifications and as directed by the departmental officers.

For all floors

POST TENSIONING WORKS : Design and Execution, of post tensioning works, including, decoiling the strands, cutting to the required lengths, supplying laying of HT strands sheathing (GI corrugated ducts 0.3mm thick) jointing with couplers, and inserting the strands, profiling, fixing live end anchorages, including the supply of stressing anchorages, suitable for 5-5 & 5-4 tendons, grout vents, making dead end anchorages, including flowering the strands, fixing tendon support bars, supervising the fixing of anti-bursting reinforcement, stressing the cables, end trimming, grouting the cables, with cement slurry, mixed with admixtures , with required tools, plants, and machineries, and consumables etc. (shuttering, concreting & reinforcement steel, shall be paid under respective items) at all heights including all leads, lifts, coordination, with the post-tensioning agency,preparation of drawings, obtaining approval from the Employer /Architect etc. Rate to include providing water, power, cement and admixture for grouting, packing of sheathing and anchorages blockings, filling of recess pockets after stressing using grouts(cement slurry mixed with approved admixtures) including providing access to post tensioning at all heights including all leads, lifts etc., all complete and as approved and as directed by the Employer /Architect but excluding shuttering, concreting & reinforcement steel which shall be payable under respective items separately. PWD Approved PT Agency Utracon Structural Systems pvt Ltd.[PWD SOR: P.NO:71- SE.NO:293]

MASONARY WORKS

Brick work: Brick Masonry using chamber burnt second class ground moulded stock bricks of size 9”x4-3/8”x2-3/4” (23x11.2x7cm) for stair case steps including proper setting, scaffolding, curing etc., complete in all respects in all floors and as directed by the departmental officers

in cm 1:5 (one of cement and five of sand) - Foundation and Basement

in cm 1:6 (one of cement and six of sand) - Ground floor

in cm 1:6 (one of cement and six of sand) - first floor

in cm 1:6 (one of cement and six ofsand) - second floor

Brick partition walls of 11.50cm thickness using best qualityII class Ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Brick Partition Wall- Ground Floor

Brick Partition Wall - First Floor

Ornamental Brick work in lime mortar 1:2 using chamber burnt second class ground moulded stock bricks of size 9”x4-3/8”x2-3/4” (23x11.2x7cm) forSudhai work on columns, slab drops, plinth bands, walls etc... including proper setting, scaffolding, curing etc., complete in all respects in all floors and as directed by the departmental officers

PLASTERING WORKS

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. Internal plastering & external plastering

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed goverment office

Providing vargapoochu over the core walls of vimanam /gopuram with lime mortar 1:1.5 complete including shaping the mukapathiram , maha nasi koou all ornamental works to proper shape by embedding broken bricks or shaped chiseled bricks rough plastering with lime mortar 1:1.5 and finishing with final ornamental plastering and nayan theervai including cost and conveyance of all materials, labour, therefore lifting of materials all working in heghts curing with water etc., complete including all extra for folding and including clearing the debris from vimanam / gopuram .

Supplying and fixing in position of FALSE CEILING ARRANGEMENTS with aluminium anodised ' T' Section and 'L' angle frame work of grid size 60x60cm with aluminium T section and 'L' angel of size 25x25x2mm thick and the same is supported @ suitable intervals by adjustable type 6mm dia MS rod with suitable threaded nuts suspended rods hung from ceiling at 120cm c/c in both directions and fixing Using Hilux Board Plain Sheets in the grid so as to give a seat to false ceiling including painting the 6mm dia MS rod etc.,complete complying with standard speificat-ions. Necessary opening and arrangements for fixing electrical fitings should be provided with suitable frame work etc., complete.

JOINERY WORKS

Supplying and fixing Teak Wood Frame for Doors and Other Similar Joinery works with the following size of 127mm x 76 mm and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc complete in all floors. T W Scantlings upto 4m.

Supplying and fixing C.W Frame for Doors, and Other Similar Joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc complete in all floors. CW Scantlings upto 4m

Supplying and fixing of solid core flush shutter with teakply on both side with teakwood lipping alround 35mm thick including cost of materials,labour charges etc.,Complete complying with standard specification.

supplying and fixing the temple type teak wood door shutter with frame , including cost of all materials ,wind appliance , furniture fittings , labours charges for manufacturing and fixing in position including fixing of furniture fittings etc.,and all complete directed as per department officers.

Supplying and fixing in position F.R.P Door shutter with frame made out of FRP sheets 3mm thick of all size 65mm x 50mm with rebate suitably reinforced using ms angle/ flats, cost of holdfasts and solid core FRP shutter panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc.,of sizes specified by engineers.Complete

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Departmental Officer before use on work (PWD _SOR =item no 269)

Fabricating Supply and Fixing and position of MS Door with single leave.The door outer frame will be 40x40x6mm MS angle intermediate stiffner will be 35x35x6mm with cross stiffiner 25x25x5 mm flats covered with 18 gauge M.S Sheet with necessary hinges,tower bolts, aldrop lenth 30mm and hold fast etc., complete with one coat red oxide primer.

Supply &fixing Mild steel grill of approved. The cost including of necessary screws, plugs, one coat of red oxide primier of approved quality, labour charges for fixing etc all complete and as directed by the departmental officers .

Supply and erection of Double Leaves Fire Rated Door with Frame having the dimension of 1200mm x 1400mm with following specification:a. Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b. Door Leaf 1mm: Galvanized 120 GSM branded make JSW c. Shutter Thickness: 46mm d. Honeycomb: In-fill e. Glue Macroplast UR-7221 f. Door Hinges: 4" x 3" x 3mm, Double Ball: Make Assa Abloy Yale Ball bearing Butt Hinges Grade SS 304 - Finish SS g. Door Closer with Standard Arm Finish: Silver h. Lock Set: Dead Lock with both side key i. Door Orientation: To be confirmed by client j. Mounting of door: Brick wall mounted k. Powder Coating: Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns l. Single Point Panic Bar (2 Horizontal): Make Assa Abloy Yale or Equivalent m. Dead Lock with both side key: Make Assa Abloy Yale or Equivalent n. Vision Panel 200 x 300mm 2 Hrs. Fire Glass Schott Pyran with Frame o. Rated Glass Schott Pyran with Frame p. Anchor Bolt with Endcaps The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, pastering, scaffolding all other conveyence as per standard methods and as directed by the Departmental Officers. (PWD_SOR : item no 335)

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Departmental Officer before use on work (PWD _SOR =item no 270)

Supplying and erecting of manually operated pull and push type rolling shutter with ISI make of approved size and section using 18 gauge GI sheet with hood cover including one coat of approved primer and transport charges etc.complete in all respects, complying with relevant standard specifications and model /brand of the rolling shutter has to be got approved as directed by the departmental officers .

Manufacturing , supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304L grade stainless steel pipe of 1.60 mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00mm thick as vertical at 900mm centre with 2nos of 25mm dia intermediate horizontal stainless steel pipe of 1.60 mm thick in between . the vertical pipe has to be welded to the 100x100x6 mm MS base plate encased in the base concrete and cleaning with passivation paste to remove the welding film with fine polishing including drilling the tiles or granite including conveyance,loading ,unloading etc .all complete complying with relevant standard specification and as directed by departmental officers . ( The quality of all materials should be got approved before use on works ).

manufacturing , supplying and fixing in horizontal position of stainless steel hand rails using fabrication pipes of 38.30 mm dia -single line , pipe design with 25 mm dia pipe connecting into the side wall with gas tungsten arc welding fixing with lockfix paste and cleaning passsivation paste to remove the welding film with fine polishing including drilling the tiles or granite including conveyance , loading unloading etc , all complete complying with relevant standard specification and as directed by the departmental officers . ( The quality of all materials should be got approved before use on works ).

FLOORING WORKS

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best quality antiskid tiles of approved colour , shade and quality laid in cement mortar 1:3 20mm thick in all floors and the top ponted with the white cement mixed same colour pigments etc ., complete complying with standard specification .( The make and brand of the tiles should be got approved by executive engineer before use on works ).

Paving the floor with best quality vertified double charged tiles of 600x600x8mm of approved colour , shade and quality laid in cement mortar 1:3 20mm thick in all floors and the top ponted with the white cement mixed same colour pigments etc ., complete complying with standard specification .( The make and brand of the tiles should be got approved by executive engineer before use on works ).

Flooring with self designed joint free rectified ceramic tiles of size 305 x 305 x 8 mm laid over 20mm thick cement mortor 1:3 base mortor over the existing slab / floor including cutting the tiles to the required size with special cutter whreever necessary , laying the position and pointing with white cement mixed with colouring pigments at the rate of 0.3 kg / sq.mt etc .complete complying with standard specification .(The make and brand of the tile should be Johnson, Kajaria, Somany ,Nitco/RAK or equivalent which has to be got approvel by executive engineer before use on words .

Dadooing walls with following best approved quality, white /colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 kgs. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. (Tile Size -450mm X300mmX8mm)

Plain cement concrete 1:2:4( one cement , two sand , four hard broken stone jelly ) using 10-12 mm jelly for wearing coat including laying compacting finishing and curing etc., as per standard specification ,.

For ground floor

For first floor

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

PAINTING WORKS

Painting two coats of newly plastered wall surface with ready mixed plastic Interior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with one coats of zinc chromide and two coats of best approved colour of synthetic enamel paint in all floors etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)using Zinc bromate

PEB STRUCTURE

Design, fabrication, supply and erection of PEB structure by using the built up sections are made from hot rolled platers conforming to ASTM A - 572 GR 50 and other sections except beams are mill sections complying with IS :2062 and the section should be provided with 2 coats of Zinc Phosphate anti corrossion paint after sand blasting and 2 coats of enamel paints as per the approved colour. Bracing rods and sag rods are made of steel bars conforming to IS 2062 with aminimum yiled strength of 240 MPA. All the fasteners should be confirmed as per the IS/ ASTM specifcations.

Supply and Installation of roofing sheets 50 mm thick puff panel, ridge ventilators, providing roof insulation of 30mm thick fibre glass insulation and 24 kgs/cum density with vinyl facing, canopy, structural steel system, metal roofing and cladding sheets, anchor bolts, down take pipes, turbo vents and all other accessories required to complete the project as per drawings attached The roofing and facsia board should be Zinc Aluminium alloy coated colour roof sheet of 0.47mm nominal thickness, cold roll formed from a cold rolled coil confirming to Astm a 792 m gRADE 80 WITH A MINIMUM YILED STRENGTH OF 550 mpA.THE EVES GUTTER SHOULD be provided with Zinc Aluminium alloy coated steel sheet of 0.8T with GI Gutter hangers. Downspouts should be provided with 100mm size of Zinc Aluminium coated sheets with GI with GI laedre straps. Galvansied purlin should be adopted as per the required size. The quoted price should include the supply and fixing charges of MS inserts in the concrete day light sheets in the roof and include facsia and gutter area also.

MOVABLE PARTITION

Providing & Fixing of EPD (Environemntal Product Declaration compliant) - Semi Automatic consisting of 100mm thick individually movable elements with sound insulation upto 50dB tested in a third party labopratory as per EN Standards, suspended from a top track only, without floor guides. Each panel to have top and bottom operable pressure seals operated by The spindle mechanism should be operated driven by a 24V DC electric motor (semi-automatic) to ensure optimum contact pressure of up to 800N.(Sweep seal is not allowed as it decreases the efficiency of the wall).The elements must be inter-connected by means of a positive locking concave/convex trapezoidal aluminium profile integrated with Magnetic Profile. Each element must be suspended on double multi-directional roller carriers which are made up of pre lubricated ball bearing steel wheels. Elements must be constructed of a non-deflecting steel tube frame and aluminium profiles, bolted together. The frame must be clad either side with 16mm MDF panels hung in acoustic isolation from the frame and allowed to vibrate independently of the frame. The facia panels must also be easily removable without requiring to dismantle the movable wall element for service/maintenance purpose. The panel must be filled with high density rock wool and sound mats in accordance with the specified sound insulation requirements.The Telescopic Element must open and close 120mm and must be operated by a single mechanism for both the top and bottom seals and the travel of the telescopic sleeve .The telescopic element must maintain all the same quality criteria as the other elements.The Acoustic Movable Wall partition should be have test certificate produced by a third party carried out in the test laboratory, accredited to DAP. The weighted sound reduction index Rw (dB) is determined in accordance with EN 20140 – 3.

WATERPROOFING & MISCELLANEOUS WORKS

Providing expansion joint of 12.5mm wide in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed.

Providing expansion joint of 12.5mm width in RCC roof slabs between RCC twin beams using pvc water bar 150 mm wide centre bulb of 4mm to 6 mm thickness of approved quality and brand and including filling the inner space with suitable non - absorbent flexible and well compressible filler materials of approved quality and covering the top surface with gi sheet30 cm wide and 1.6 mm thick using phill plugs , gi screws , limpet cup washers , etc.,complete complying with standard specifications and as directed.

Providing Polymer coating (Water Proof coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust,foreign,matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry : Dry blend and polymer liquid shall be mixed into desired ratio as per recommandation of the supplier.The mix shall be stirred thoroughly until no bubbles remain in the mix.any lumps found in mix shall be removed.Apply first coat of polymer modified cementitious slurry by brush on wet cleanes surface.After drying,second coat shall be applied on the first coat as directed by the departmental officers etc,The rate inclusive of cost of materials and labour,etc complete complying with standard specication and as directed by the departmental officers (PWD -SOR -Item no223)

Supplying & fixing SFRC MAN HOLE Cover of size 600x600mm etc complete complying with standard specification and as directed by the departmental officers (PWD -SOR :iTEM NO 295)

SEWAGE TREATMENT PLANT

Supply & Installation Testing and commissioning of Sewage treatment Plant based on attached growth technology using the 'Moving aerated Biomedia Reactor (MBBR) process .complete mechanical and electrical items with stand by pumps. All criteria should meet relavant norms and codes of pollution board . complete as per stanard specification and as directed by by the competent authority .(40KLD)

Raw Sewage Transfer Pump Type: Centrifugual Nonclog, Capacity: 1.25 cum/hr, Head: 12 m, MOC: CI, Make : Kirloskar Oil Skimmer Mechanishm Capacity : 0-4LPH, Type : Belt Skimming type, MOC of Belt : PU, Oil Collection Tank : 100 Liters Coarse & Fine Bar Screen Bar screen Size: 0.6m x 0.6m, Spacing: 6mm & 10 mm, Bar Thickness: 5 mm, MOC: SS304, Make: HECS Air Blower - Aeration Tank Type: Tri Lobe Roots Blower, Capacity: 70 m3/ hr, Pressure: 0.4 ksc, MOC: CI, Make: Airvak, Air Blower Motor, Motor MOC: CI, Motor Make: Kirloskar / CGL, Diffusers - Aeration tank & Collection Tank, Type: Tubular Fine Bubble, Diameter: 63mm, Length: 800 mm, MOC: EPDM, Make: PROFLEX / AquaFlexi / Eq, MBBR Media, Type: Floating Type Bio Media, Surface area: 250 sqm / cum, MOC: PP, Make: PROFLEX / AquaFlexi / Eq Secondary Tube Settler Media Type: Inclined Settler, Structure: Hexagon Chevron shaped,Self supprt, Straight ht: 750 mm, Plan Settling Area: 12m2/m3(at 60 deg slope), Laying Angle: 60 deg, Max.Temperature : 65 deg Celcius, Fitting arrangement: Tongue & Grooves, Sheet Thickness: 1 mm, MOC: UV Stbilized PVC, Make: PROFLEX / AquaFlexi / Eq Sludge Transfer Pump Type: Centrifugal Nonclog, Capacity: 1.25 cum/hr, Head: 12 m, MOC: CI, Rating: 0.5 HP, Make of Pump: Kirloskar/ eq,

Screw Pump Type: Single Stage Single Screw, Capacity: 1 cum/hr, Head: 50 m, MOC of Rotor: SS, MOC of Stator: Nitrile Rubber, Make: Icura / eq. Filter Press Unit Type: Motorized, Capacity: 1 cum/hr, Size ; 18 inch x 18 inch, No, of Plates: 8 nos, No. of Chambers:7 nos, MOC of Plates: PP, MOC of Structure: MS Epoxy, Make: Icura, NaOCl Dosing System Dosing Pump Type: Electronic Metering, Capacity: 0 - 6 lph, Pressure: 3 Kg/cm2, MOC: PP, Make: Edose / Eq, Dosing Tank Type: Cylindrical Vertical, Capacity: 100 ltrs, MOC: LDPE, Make: E-Dose / Eq, Filter Feed Pump, Type: Centrifugal Monobloc, Capacity: 1.25 cum/hr, Head: 30 m, MOC : CI, Make of Pump : Kirloskar/ eq, Pressure Sand Filter Type: Cylintrical vertical, Capacity:1.25 cum/hr, Diameter: 500 mm, HOS: 1500 mm, Thickness : 5mm / 6mm, MOC: MSEP, Media: Pebbles / Sand Accessories: UPVC Frontal Piping with 25NB MPV, Make of Filter:HECS, Activated Carbon Filter Type: Cylintrical vertical, Capacity: 1.25 cum/hr, Diameter: 500 mm, HOS: 1500 mm, Thickness : 5mm / 6mm, MOC: MSEP, Media: Pebbles / Sand / Activated Carbon, Accessories: UPVC Frontal Piping with 25NB MPV, Make of Filter:HECS Interconnecting Pipes & Valves MOC of Water Pipeline: CPVC Sch 40, Make of CPVC Pipes: Astral/ Supreme/ Finolex, MOC of Air Pipeline: GI B Class, Make of GI Pipes: Jindal /Tata., Makes of Fittings : Astral/ Supreme/ Finolex, Instruments, Pressure Gauges, Make : H - Guru / Eq, Float Switch, Make : Aster / Eq, Electro Magnatic Flow Meter,

Make : Forbes Electrical Panel & Accessories Type : Wall Mounted - Non Compartmentalized, Sheet Thickness: 1.6 mm, MOC: CRCA Powder Coated, Make of Panel: HECS, Components: MCB/OLR/Contactor, Make of Switchgears: Siemens/Schneider/ABB, Cables and accssories- 1 Lot, Make of Cables: Havells/orbit/polycab Total Project Cost for Electro Mechanical Equipments Rs The above cost included Design, Engineering, Erection & Commissioning & Transportation of Equipments

supplying and erection of FRP Under Ground Tank of size 2.7 m dia ,12.7 m length and 13.5 mm thick made of food grade polymer and virgin polymer granulers as per appropriate ASTM standard with necessery man hole of size 555mm dia for maintanance .anchors and nylon belts along with necesssary fixing arrangements shall also be provided etc.,all complete as directed by department officials .

supplying and erection of FRP STP Tank of size 2.3 m dia ,10.5 m length and 13.5 mm thick made as per appropriate ASTM standard with necessery man hole of size 555mm dia for maintanance .anchors and nylon belts along with necesssary fixing arrangements shall also be provided etc.,all complete as directed by department officials .

Supplying and fixing of chain link mesh of size 2"*2" using 10 gauge galvanized iron of all size and complete as directed by departmental officers.

PATHWAY WORKS

Supplying and filling in foundation, basement, etc with Filling Granular Sub Base in layers of not more than 15 cm thick well watered, Without consolidation etc. complete complying with standard specification and as directed by the officers

Supplying and laying rubber mould hydraulic pressed Paver block Providing and laying of 83mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size and uniform shape of approved make to be laid in furling bone pattern with stone dust cushion below the uniform shape of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 30mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,. I Paver Grey -83mm thk

Supplying and laying grass Paver block Providing and laying of 120mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver block in size of minimum compressive strength in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shape of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 30mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.600mm x600 mm.

Supplying and laying of 16/18 mm thick granite slab of leather finish (steel grey or sadherhalli) with stone dust cushion below the uniform shape of approved non skitting surface in the top and the rate including levelling the base preparation of granite as sub base, stone dust cushion 30mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying granite slabs of maximum size 600mmx600mm as per standard specification,.

Paving with cutstone flooring using cutstone 600x600 mm and 100 mm thick the all the sides are machine cutting top surface is neetly dressed and pointing with lime mortar 1:1.5 including all materials and labour charges .

Supplying and laying of 80mm thick tivoli paver block with stone dust cushion below the uniform shape of approved non skitting surface in the top and the rate including levelling the base preparation of granite as sub base, stone dust cushion 30mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying granite slabs of maximum size 600mmx600mm as per standard specification,.

Supplying and laying of 80mm thick cobble paver block with stone dust cushion below the uniform shape of approved non skitting surface in the top and the rate including levelling the base preparation of granite as sub base, stone dust cushion 30mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying granite slabs of maximum size 600mmx600mm as per standard specification,.

Supplying and fixing of pre-cast kerb stone of size 600x 600x 100 mm made in CC 1:3:6 (One of cement, three of sand and six of hard broken stone jelly) using 20mm size hard broken stone jelly including the cost of Kerb stone moulding, laying, curing, transporting, pointing the slab with 1:3 to full depth of slab and as directed by the Project Officer. Kerb 600x600x100 mm

ROAD DEVELOPMENT WORKS

Earth work in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machinery and tippers including benching, formation of bunds, breaking clods, sectioning etc., complete

Providing and laying of Gravel not less than 15mm thick including cost and conveyance of the same to work site from approved quarry including stacking the same to departemental gauge for premeasurement including all labour charges for laying, spreading, including all hire and fuel charges for power roller for compaction, etc., complete and as directed by the Project Officer

Providing, laying, spreading and compacting graded stone aggregates for Wet Mix Macadam 250mm thick, including premixing the materials with water at OMC in mechnanical mix plant, conveyance of mixed materials by tipper to site, laying in uniform layers using pavers in Sub Base/ Base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5

Providing and laying Prime Coat over WBM/ WMM surface using 7 Kg of Emulsion Bitumen (SS1) per 10 sqm for preparatory to another bituminous construction over it, including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as perClause 502 of MORTH Rev-5

Providing and laying Tack Coat over Existing BT surface using 2 Kg of Bitumen Emulsion (RS1) per 10 sqm for preparatory to another bituminous construction over it including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as perClause 503 of MORTH Rev-5

Providing, laying Dense Bituminous Macadam using 0.40cum of 37.50-13.20mm, 0.35cum of 13.20-2.36mm and 0.36cum of 2.36mm & below size IRC metal with 71.30kgs of VG30 grade bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, heating the bitumen, aggregate and mixing them in the required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to site, spreading the mix to uniform thickness of 75mm with mechanical paver to the specified grades and cross sections and consolidated by Vibratory Roller to the required density etc., including labour for attending to paver to site etc., including hire and fuel charges for 20-30t CMP with bitumen boiler, tipper trucks, Paver Finisher, Vibratory roller and all other tools and plant required, including all other incidental charges etc., complete as per specification using CMP as per clause 505 of MORTH rev-5.

Providing and laying Bituminous Concrete using 0.13 cum of 19.00-9.50mm, 0.17 cum of 9.50-2.36mm and 0.26 cum of 2.36 and below with 50.30kgs of VG30 bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 40mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tonne Vibratory to the required density etc., including labour for attending to paver to site etc., including hire charges and fuel charges for 20-30 t CMP with bitumen boiler, tipper trucks, Paver Finisher, Vibratory roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 507 of MORTH Rev-5

Providing and applying 2.5 mm thick road marking strips (retro reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Project Officer and accordance with applicable specifications

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/ms and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

WATER SUPPLY ARRANGEMENT WORKS

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. and as directed by dept Officers.(PWD SOR Sl.No:394)

40mm PVC - 10kg/cm2 Pipes

20mm PVC - 10kg/cm2 Pipes

Supplying and fixing the following dia PVC (SWR) pipe type B class conforming to IS 13592and relevant specials including packing the joints with rubber lubricant fixing them into walls with necessary GI Bolts and Nuts with special clamp made of MS angle/Flat including cutting, bending (excluding the cost of MS angle/flat) holding wherever necessary and making good of the dismantled portion with necessary connections to sanitary fittings etc., complete complying with relevant standard specification and as directed by the departmental officer (PWD SOR Sl.No:394)

Soil Pipe - (110mm Pipe 6kg/cm2)

Wastewater Pipe - (75mm Pipe 6kg/cm2)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. cand as directed by dept Officers..

110 mm dia PVC- 4 kg/cm2 pipes

Supply and fixing of GM Gate Valve 40mm Dia heavy type with necessary flanges, gaskets, nuts and bolts complete as required and shall be compatable with Composite pipes as applicable.etc., complete complying with relevant standard specification and as directed by the departmental officer. The quality and brand Gate Valves is to be got approved by the Department officer before fixing.(PWD SOR Sl.No:394)

Supply and fixing of Ball Valve with necessary flanges, gaskets, nuts and bolts complete as required and shall be compatable with Composite pipes as applicable.etc., complete complying with relevant standard specification and as directed by the departmental officer. The quality and brand Gate Valves is to be got approved by the Department officer before fixing.(PWD SOR Sl.No

Supplying and fixing of C.P 2Way Bip cock Long body with stainless steel health faucet and wall flange like ESSCO, Jaquar fitiing including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality and brand of fittings should be check before use).

Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Departmental Officer before use on works.)

Supply & fixing of Prelaminated Board of 12-18mm thick for Toilet Partition made from high pressure laminate as per IS 2046 under high specific pressure greater than 5 MPA and temperature 120 degree of standard size 2100x900x1550mmm and door dimension of 1995x600mm and bottom gap is 100mm and urinal partition of 12 mm thick and size of 500mm top and 400mm bottom and 1200 mm height along with necessary fittings and fixing arrarngements etc complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittingssuch as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the departmental officer before use on works)

Supplying and fixing in position best quality and approved make Indian made white glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the departmental officers before use on works).

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the departmental officers before use on works) (Cast Iron Nahani Trap of size 100 x 75mm with stainless steel gratings)

Supplying and fixing 150mm x 100mm size stone ware Gully trap with iron gratings over a bed of 150mm thick brick jelly concrete in SFRC cover slab of size 300 x 300mm over using 40mm size brick jelly and brick masonry wall 115 mm thick using fly ash bricks of size 23x11x7cm in cm 1:5 (One of cement and five of sand ) plastered with CM 1:3 (One of cement and three of sand) 12mm thick Including fixing cover slab fixing in position curing finishing etc., All complete complying with relevant standard specification and as directed by the departmental officer.

Construction of Inspection chamber of following sizes with brick jelly concrete 1:8:16 ( one of cement eight of sand and sixteen of broken brick jelly using 40mm gauge broken brickjelly 15cm thick for foundation and 23cm thick brick masonry in C.M. 1:5 ( One of cement and five of sand) using fly ash bricks of size 230mm x110mm x70mm, plastering with cement mortar 1:3 ( One of cement and three of sand) 12mm thick on both sides top and bottom including earth work excavation RCC 1:2:4 ( One of cement two of sand and four of 20mm gauge hard broken stone) Including SFRC Cover Heavy duty collor with slab of required size fixing in position curing finishing etc., complete complying with relevant standard specification and as directed by the departmental officer. (Inspection 0.60x0.60m (inside opening))

Inspection Chambers (0.45x0.45)

Inspection Chambers (0.60x0.60)

Inspection Chambers (0.9x0.9)

Supply and fixing 5HP summersible pump set asper isi specification with isi mark hydurallically testing and commisioning of submersible wet type suitable for sump with pressure gauge and necessary length of 2 nos of pp from pumpset to the top of the sump and other required accessories etc complete in all respect and as directed by the departmental officers, the motor and the pumpset supplied should satisfied the following duty conditions etc complete complying with standard specification and as directed by the departmental officers.SOR(M1068)

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4kg./sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by dept officers.

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications and as directed by dept officers (The PVC cowl should be got approved by the Executive Engineer before use on works).

Supplying and fixing of PVC / Fibre Glass Framed 5.5 mm thick Mirror, Shelf Type with Hard Board Backing of size 1000x780mm including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use).

Supplying and fixing of Anodised Aluminium Towel Rail 60cm long and 20mm dia with Brackets including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use).

Supplying and fixing in position CP shower rose with CP stop cock and CP Bibcock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The CP shower rose should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position CP shower rose with hand shower and double mixer cp stop cockarrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The CP shower rose should be got approved by the Executive Engineer before use on works).

Suppling and fixing in position of the following PVC specials Finolex or equivalent make working pressure 10 kg / sq cm confirming to ISI etc ., complete complying with standard specification and as directed by the department officers ( the pvc specials should be got approved by the executive engineer before use on words .

40 mm dia

pvc bend

pvc coupling

pvc tee

pvc elbow

pvc reducer

pvc reducere tee

20mm dia

pvc bend

pvc elbow

pvc tee

15mm dia

pvc bend

nipple

FIRE FIGHTING ARRANGEMENT

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo /Equivalent) SOR (M-0770)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent) SOR (M-0771)

Supply and fixing of stored pressure ABC (Mono Ammonium Phosphate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., Including conveyance, all incidental charges, necessary scaffolding and re- doing the dismantled portions to its original condition wherever found necessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY / FIRST / EQUIVALENT SOR (M-0851)

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc. complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY / FIRST / EQUIVALENT SOR (M-0852)

Supply, installation, testing and commissioning of Micro Processor based conventional 4 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. SOR (M-0769)

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE SOR (M-0791)

Supply, erection, testing and commissioning Mono Block type Fire Fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fizing and incidental charges etc., complete as per standard specification and as directed by the Departmental Officers. (Make:Kirloskar / Equivalent) SOR (M-0792)

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT. SOR (M-0845)

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges,neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT. SOR(M-0794)

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Departmental Officers -SOR(M-0842)

Supply, erection, testing and commissioning of MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Officer Red painting including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard by the Departmental Officers. Make: JINDAL / EQUIVALENT

Hydrant Pipe

150mm Dia SOR(M-0798)

100mm Dia SOR (M-0799)

Sprinkler Pipe

100mm Dia SOR (M-0799)

80mm Dia SOR (M-0800)

40mm Dia SOR (M-0803)

25mm Dia SOR (M-0804)

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table ‘E’,gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR /EQUIVALENT

200mm Dia SOR (M-0811)

100mm Dia SOR (M-0813)

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

200mm Dia SOR(M 0816)

150mm Dia SOR (M -0819)

Supply, erection, testing and commissioning of Gun Metal Gate Valve of size 50mm dia size including necessary MS flange of table ‘E’, gaskets, bolts & nuts etc., installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT. SOR (M-0819)

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Butterfly Valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

150mm Dia SOR (M-0817)

100mm Dia SOR (M-0818)

Supply, fixing, testing & commessioning of dial type (150mm) Glycerin filled pressure gauge with isolation ball valve suitable for working pressure of 250 PSI with no syphon, cost shall be inclusive for providing any short pieces, nipples, elbows etc all complete as per standard specification and directed by the departmental officers

Providing, fixing pipe supports 100mm dia from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification. SOR (M-0847)

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT. SOR (M-0795)

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: HGURU / ISI MAKE / EQUIVALENT. SOR (M-0828)

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT. SOR (M-0846)

Supply erection testing and commissioning of Electric Motor Driven Fire Pumpset suitable for automatic operation and consisting of following: a. 1 No. horizontal split casing centrifugal type fire pump capable of delivering 4550 LPM against a total head of 110 metres, so as to ensure a minimum pressure of 3.5 kg. per sq.cm at the farthest top most hydrant / outlet with pump casing of cast iron to grade FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring etc., of non-corrosive metal either like bronze, brass or gun metal and shaft of stainless steel. b. 1 No. squirrel cage induction motor of 175 HP, 415 Volt, 3 phase 50Hz rating, conforming to IS:325-1978 with class "F" insulation, totally enclosed, IP 55 for enclosure fan cooled type conforming to relevant protection clause of IS 4691, synchronous speed of 2900 RPM. c. Common bed plate fabricated with MS channel / cast iron type for assembling the pump and motor flexible coupling between the pump and the motor with coupling guard for protection - 1 No. d. Making cement concrete foundation suitable for the above pumpset including vibration isolation pads as necessary, foundation bolts, brackets, clamp fixtures, grouting, etc., in accordance with the manufacturer's design and as per standard methods and including conveying, fixing and incidental charges, etc., complete as per standard Specification and as directed by the Departmental Officers.SOR (M-0832)

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of followings complete in all respects as required. a. 1 No. horizontal split casing centrifugal type fire pump capable of delivering 2850 LPM against a total head of 70 metres, so as to ensure a minimum pressure of 3.5 kg. per sq.cm at the farthest top most hydrant / outlet with pump casing of cast iron to grade FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring, etc., of non-corrosive metal either like bronze, brass or gun metal and shaft of stainless steel. b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. c. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dynamo, solenoid switches etc. d. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre filter, after filter etc.SOR (M-0835)

FURNITURE

Site - A

Supply of High Back Mesh Ergonomic Conference Chair (50cm D x 55cm W x 107cm H) with Heavy Duty Metal Base (chrome). The chair should have a weight capacity of upto 125 kgs. Castors: 50mm Dual Caster Wheels; Gas-lift : Class 4; Frame Material: MS Chrome Metal Base with Breathable Mesh (backrest) & Black cushion seat; Color: Chrome. The prototype/model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of Modular Conference Table (Each module size: 110cm L x 55cm W x 75cm H) consisting of total 21 modules with Heavy Duty Metal Base & framework (Steel Grey Powder coated), a pop-up box provision (consisting of one mic point, one HDMI point, one LAN socket & one 5A socket per module table) and prelaminated plywood board for table top with postformed edges. The prototype/model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of Modular workstation Table (120cm L x 60cm W x 75cm H) with Heavy Duty Metal Base & framework (Steel Grey Powder coated), a pop-up box provision (one voice, one LAN socket & three 5A socket) and prelaminated plywood board for table top with postformed edges. The prototype/model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of High Back Mesh Ergonomic Office Chair (50cm D x 65cm W x 115cm H) with 2D Adjustable Armrests & Lumbar Support, Smart Multi-Tilt Lock Mechanism, adjustable headrest & Heavy Duty Metal Base (Black). The chair should have a weight capacity of upto 125 kgs. The backrest tilt up to 135° and lock at 3 angles between 90°-135°; Castors: 50mm Dual Caster Wheels; Gas-lift : Class 4; Frame Material: Glass Filled Nylon Structure with Breathable Mesh; Color: Black. The prototype/model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of three seater waiting area Chair (177cm D x 66cm W x 78cm H) made of full body stainless steel of grade 304. The curved continuous backrest & seating made of perforated design SS sheet of required thickness. The each chair should have a weight capacity of upto 125 kgs. The prototype/model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of Lounge Arm-Chair (74.0 cm H x 63.5 cm W x 60.9 cm L) with curved wooden framework crafted with printed fabric upholstery & cushion. The chair should have a weight capacity of upto 110 kgs. The prototype /model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of Reception Table (350cm L x 60cm W x 75cm H) made with country wood crafted with laser cut/CNC carved ornamental front panel works (Vallalar theme based concept), a pop-up box provision (one voice, one LAN socket & three 5A socket) and prelaminated plywood board for table top with postformed edges. The prototype/model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of Receptionist Arm-Chair (75.0 cm H x 55 cm W x 55 cm L) with curved wooden framework crafted with printed fabric upholstery & cushion. The chair should have a weight capacity of upto 110 kgs. The prototype /model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of Workstation Table (150cm L x 60cm W x 75cm H) made with country wood, a pop-up box provision (one voice, one LAN socket & three 5A socket) and prelaminated plywood board for side panels below table top. The prototype /model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of Medium Back Mesh Ergonomic Office Chair (55cm D x 60cm W x 110cm H) with 2D Adjustable Armrests & Lumbar Support, Smart Multi-Tilt Lock Mechanism & Heavy Duty Metal Base (Chrome). The chair should have a weight capacity of upto 125 kgs. The backrest tilt up to 135° and lock at 3 angles between 90°-135°; Castors: 50mm Dual Caster Wheels; Gas-lift : Class 4; Frame Material: Glass Filled Nylon Structure with Breathable Mesh; Color: Chrome. The prototype/model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of Staff Room Arm-Chair (75.0 cm H x 58 cm W x 60 cm L) with curved wooden framework crafted with plastic knitted wire/cane backrest and printed fabric with cushion seating. The chair should have a weight capacity of upto 110 kgs. The prototype /model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of wooden 3 seater lounge sofa (H 81cm x L 157cm x W 69cm) with curved wooden framework crafted with plastic knitted wire/cane backrest and printed fabric with cushion seating. The chair should have a weight capacity of upto 125 kgs per seat. The prototype /model sofa with finishing materials shall be got approved by the departmental officer before supply.

Supply of Traditional lounge Table (H 43cm x W 112cm x D 58cm) made with country wood and prelaminated plywood board for side panels below table top. The prototype /model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of Laboratory Table (Each module size: 150cm L x 60cm W x 90cm H) consisting of 14 modules made with country wood and prelaminated plywood board for side panels below table top. The prototype /model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of country wooden stool (45cm Dia x 80cm H) with anti-slip buffers/bush. The stool should have a weight capacity of upto 150 kgs. The prototype /model stool with finishing materials shall be got approved by the departmental officer before supply.

Supply of Class room Instructor Table (180cm L x 100cm W x 75cm H) made with country wood and prelaminated plywood board for side panels below table top. The prototype /model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of Staff Dining Table (210cm L x 120cm W x 80cm H) made with country wood and prelaminated plywood board for side panels below table top. The prototype /model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of country wooden stool (45cm Dia x 60cm H) with anti-slip buffers/bush. The stool should have a weight capacity of upto 150 kgs. The prototype /model stool with finishing materials shall be got approved by the departmental officer before supply.

Supply of Lecture hall Ergonomic Chair (50cm D x 50cm W x 85cm H) with a foldable writing pad (prelaminated MDF board) attached to the armrest and storage shelf below seating made of MS mesh. The chair should have a weight capacity of upto 120 kgs. Frame Material: MS chrome finish; Color: chrome; Backrest & Seating Material: Cushion with black fabric. The prototype/model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of wooden 3 seater lounge sofa (H 81cm x L 164cm x W 69cm) with curved wooden framework crafted with printed fabric with cushion backrest & seating. The chair should have a weight capacity of upto 125 kgs per seat. The prototype /model sofa with finishing materials shall be got approved by the departmental officer before supply.

Supply of Traditional lounge Table (H 45cm x W 60cm x D 60cm) made with country wood and prelaminated plywood board for side panels below table top. The prototype /model table with finishing materials shall be got approved by the departmental officer before supply.

Supply & Fixing of MS Powder coated fixed theatre chair (50cm D x 50cm W x 75cm H) with fixed armrest and base made of sturdy MS stand anchored to the floor. The chair should have a weight capacity of upto 120 kgs. Frame Material: MS Metal Base with ABS plastic (backrest) & black cusion seat; Color: Red ABS plastic backrest. The prototype /model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of wooden 3 seater lounge sofa (H 78cm x L 155cm x W 70cm) with curved wooden framework crafted with bamboo cane knitted backrest and printed fabric with cushion seating. The chair should have a weight capacity of upto 125 kgs per seat. The prototype /model sofa with finishing materials shall be got approved by the departmental officer before supply.

Supply of Visitor Chair (50cm D x 50cm W x 91.5cm H) with fixed armrest and base made of curved chrome plated steel runners. The chair should have a weight capacity of upto 110 kgs. Frame Material: MS Chrome Metal Base with Breathable Mesh (backrest) & black cusion seat; Color: Chrome. The prototype /model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of High Back Mesh Ergonomic Office Chair (50cm D x 65cm W x 115cm H) with 2D Adjustable Armrests & Lumbar Support, Smart Multi-Tilt Lock Mechanism, without headrest & Heavy Duty Metal Base (Chrome). The chair should have a weight capacity of upto 125 kgs. The backrest tilt up to 135° and lock at 3 angles between 90°-135°; Castors: 50mm Dual Caster Wheels; Gas-lift : Class 4; Frame Material: Glass Filled Nylon Structure with Breathable Mesh; Color: Chrome. The prototype/model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of Visitor Chair (55cm D x 50cm W x 91.5cm H) with fixed armrest and base made of curved MS powder coated steel runners. The chair should have a weight capacity of upto 120 kgs. Frame Material: MS black Metal Base with Breathable Mesh (backrest) & black cusion seat; Color: Black. The prototype /model chair with finishing materials shall be got approved by the departmental officer before supply.

Supply of Canteen Table (90cm L x 90cm W x 75cm H) made with full body Stainless steel (Grade 304) Stand/base and engineered marble table top. The prototype /model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of full body stainless steel (Grade 304) canteen stool (40cm Dia x 61cm H) with anti-slip buffers/bush. The stool should have a weight capacity of upto 150 kgs. The prototype /model chair with finishing materials shall be got approved by the departmental officer before supply.

Site - B

Supply of King size cot (H 70cm x W 189cm x D 212cm) with padded head rest along with 5 inch PU Foam mattress (L 198cm x B 183cm). The Cot should be carpenter assembled or factory made with country wood framework as a primary material and prelaminated MDF board of suitable thickness as a secondary material with necessary fittings, joineries and accessories. The head rest should be finished with Foam 32D with Polyester Fabric. The prototype/model cot with finishing materials shall be got approved by the departmental officer before supply.

Supply of Reception Table (180cm L x 60cm W x 75cm H) made with country wood crafted with MDF board front panel works and prelaminated plywood board for table top with postformed edges. The prototype/model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of 2-Way adjustable home-care bed with Aluminium Collapsable Guard side rails for added user safety for elderly (H 26.5-86cm x W 98cm x D 226cm) with abdomen elevation of upto 80 deg and leg elevation upto 40 deg (Fowler’s, semi-Fowler’s, high-Fowler’s, and standard chair positions) with mechanically operated back rest and knee rest by super-smooth crank mechanism along with 5 inch standard hospital mattress. The sturdy frame should ensure a weight capacity of upto 175 kgs. It should feature 5 inch aluminum caster wheels and brake pedals. The head rest & foot rest should be in durable ABS material finish. The prototype/model cot with finishing materials shall be got approved by the departmental officer before supply.

Supply of Reception Table (180cm L x 90cm W x 75cm H) made with country wood crafted with MDF board front panel works and prelaminated plywood board for table top with postformed edges. The prototype/model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of Single cot (H 86cm x W 97cm x D 193cm) with padded head rest along with 5 inch PU Foam mattress (L 190.5cm x B 91.5cm). The Cot should be carpenter assembled or factory made with country wood framework as a primary material and prelaminated MDF board of suitable thickness as a secondary material with necessary fittings, joineries and accessories. The head rest should be finished with Foam 32D with Polyester Fabric. The prototype/model cot with finishing materials shall be got approved by the departmental officer before supply.

Supply of Reception Table (210cm L x 90cm W x 75cm H) made with country wood crafted with MDF board front panel works and prelaminated plywood board for table top with postformed edges. The prototype/model table with finishing materials shall be got approved by the departmental officer before supply.

Supply of 2-Way adjustable hospital bed for out-patients (H 26.5-86cm x W 98cm x D 226cm) with abdomen elevation of upto 80 deg and leg elevation upto 40 deg (Fowler’s, semi-Fowler’s, high-Fowler’s, and standard chair positions) with mechanically operated back rest and knee rest by super-smooth crank mechanism along with 5 inch standard hospital mattress. The sturdy frame should ensure a weight capacity of upto 175 kgs. It should feature 5 inch aluminum caster wheels and brake pedals. The head rest & foot rest should be in durable ABS material finish. The prototype/model cot with finishing materials shall be got approved by the departmental officer before supply.

Supply of PVC Cane outdoor dining furniture set with one no of table (circular table of diameter 900mm)with four nos. of chairs (ciruclar chairs of diameter 500mm) along with outdoor 360 degree rotating patio Umbrella (9ft diameter) of white colour waterproof fabric (230 GSM)along with MS pole (8 ft tall) and floor stand (total weight 100 kg) with relevent standard specifications and as directed by the department officers.with relevent standard specifications and as directed by the department officers.

LANDSCAPE

TREES (6mts) C/C Pits of size 600mm x 600mm x 600mm filled with 50% existing mother earth and balance 50% filled with a mixture of Red soil and manure. The rate includes labour charges for pitting, filling, supply and planting of healthy plants as per planting drawing. The trees should be stacking to protect the trees from wind. The rate does not include supply of soil, manure and maintenance which is seperately Quoted. 7' TO 8' Height]

Albizia procera (Karoi tree)

Alstonia scholaris (Indian Pulai)

Erythrina variegata (Tiger's claw or Indian coral tree)

Ficus religia (peepal tree)

Lagerstroemia lanceolata (Vevala)

Svevgium cumini (Java Plum)

Tectona grandis (Teak)

Terminalia beilivica (Bhenda)

Terminalia catappa (Indian Almond)

Vitex altissima (peacock chaste tree)

Bambosa Vulgaris (Common Bamboo)

Bambosa wamin (Buddha's Belly Bamboo)

Azadirachta Indica (Neem)

Delonixregia (Gurmohar)

Thespesia popuinea (Bhendi Tree)

Ziziphus mauritiana (Indian Jujube)

Spathodea companulate (African Tulip Tree)

Cassia fistula (Golden Shower)

Peltophorum pterocarpum (Copperpod)

Ficus benghalensis (the banyan)

Millingtonia hortensis (Indian Cork-Tree)

Mimusops elengi (Tanjong Tree)

Phyllanthus emblica (Indian gooseberry or amla)

Pierocarpus mersupion (Malabar kino)

Swietenia mahagoni (West Indian Mahogany)

SPL PLANTS: Pits of size 450mm x 450mm x 450mm filled with 50% existing mother earth and balance 50% filled with a mixture of Red soil and manure. The rate includes labour charges for pitting, filling, supply and planting of healthy plants as per planting drawing The rate does not include supply of soil, manure and maintenance which is seperately

Alangium salvifolium (Alanji)

Bauhinia purpurea (Purple Orchid Tree)

Bauhinia variegato ( orchid tree)

Nyctanthes ar bor-tristis (Night Blooming Jasmine)

Pithecellobaum dulce (Madras Thorn)

cassin glauco (Kaneera Karuvali Khiri)

Hibiscus tiltaceus (Sea Hibiscus)

Comeina arborea (Kashmir Tree)

SHRUBS (0.30 mts) C/C SHRUBS: Pits of size 300mm x 300mm x 300mm filled with 50% existing mother earth and balance 50% filled with a mixture of Red soil and manure. The rate includes labour charges for pitting, filling, supply and planting of healthy plants as per planting drawing. The rate does not include supply of soil, manure and maintenance which is seperately quoted. [1'-0" to 2'-0" Height

Carissa carandas (Kerenda)

Lagerstroemia parviflora (Crepe Flower)

Cymbopogon nardus (Citronella Grass)

Adulsa (adhatoda vasica)

Gymnema sylvestre(gurmar)

Plumeria Alba (White Frangipani)

GROUND COVERS (0.20 mts) C/C GROUND COVERS: Pits of size 300mm x 300mm x 300mm filled with with a mixture of Red soil and manure. The rate includes labour charges for pitting, filling, supply and planting of healthy plants as per planting drawing The rate does not include supply of soil, manure and maintenance which is seperately quoted

Apluda mutica L (Mauritian Grass)

Aristida adscensionis L (Common needle grass)

Aristida selacea Retz. (coarse perennial)

Bothriochloa pertusa (L.) A. Camis (Indian-bluegrass)

Brachiaria remota (Retz) Haines

Chloris barbata Sve (Swollen Windmill Grass)

Cymbopogon coloratus (Hook. f) Stopf Cynodon barberi Rang & Tad (Bermuda grass)

Cynodon dactylon (L) Pers. (Bermuda grass)

Cyrtococcum oxyphyllum (Steud.) Stapf ( Bow grass)

Echinochloa colona (L) Link (jungle rice)

SEDGES

Cyperus CompressusL.. (annual sedge)

Cyperus difformis L.. (smallflower umbrella-sedge)

Cyperus distans L.. (slender cyperus)

Supply and laying of Shade grass in dibbling method

Transplantation of trees with in a distance of 2km including excavation around existing tree, pruning of branches, lifting, loading and transportation of existing tree, digging pits for placing tree at new place, adding manure, sand, fertilizer, hormones and bio fertilizer to it. Levelled and neatly dressed and disposal of surplus materials from old existing and new sites to designated place. Each tree should be firmly secured to the stake so as to prevent excessive movement, flooding with water, treatment of roots, rope and gunny bags as per direction of the officer incharge. T&P and all required materials shall be arranged by the contractor and nothing extra shall be paid on this account.(a) Girth of tree shall be measured at a height of 1m above ground level

12.1.1 Girth of trees upto 50cm.(each)

12.1.2 Girth of trees beyond 50cm and upto 90cm..(each)

12.1.3 Girth of trees beyond 90cm and upto 150cm.(each)

12.1.4 Girth of trees beyond 150cm.(each)

Supplying and Fixing of Granite slab Sign Board of size leather (bottom 35%) and polished finish (top 65%) (steel grey or sadherhalli) with carved out Signage texts and painting the texts with approved synthetic enamel paint (as per design from IEC or Signage Expert/vendor; approved by dept. officer) vertically fixed on concrete haunching of size 900mm(L)x450mm(W)x600mm(D) fixed with metal clamping and necessary bolts along with necessary earthwork excavation for casting concrete haunching and refilling earth at mentioned places as per drawing. The rate is including levelling the base preparation of concrete haunching as sub base, GSB of 200mm thick laying out of pavement or natural ground to fix the edge vibrating the pavers,sweeping tranporting loading unloading of laying granite slabs of mentioned size as per standard specification.

600mmx1950mmx100mm

300mmx1950mmx100mm

300mmx1500mmx100mm

ELECTRICAL WORKS

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End (Data 1)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End.) (Data 2)

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End (Data 3)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End (SD 375)

LIGHT FIXTURES

Supply and fixing of 40W 4’ LED Fitting with WW LED (Higher end) complete on wall or ceiling with with PVC unsheathed Copper leads from terminals to the fitting. (Data 4)

Supply and fixing of 40W 4’ LED Fitting with WW LED (Higher end ) fittting complete with with conduit pipe suspension from ceiling with PVC unsheathed copper leads from terminals to the fitting with fluorescent Tubes. (Data 5)

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD 526)

Supply and fixing of 3W LED foot lamp with LED (Higher end) suitable to be fixed on 3M flush type (GI) box inflush with wall with necessary accessories with PVC unsheathed copper leads from terminals to the fitting. (Data 6 )

Supply and fixing of 2' 6W LED Mirror light fitting with LED (Higher end) on wall with necessary accessories with PVC unsheathed copper leads from terminals to the fitting. (Data 7)

Supply and fixing of 36W LED 2x2 square type Recessed / Sueface fitting with LED (Higher end) on false Ceiling or ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. ( Data 8)

Supply and fixing of 18W LED square type Recessed / Surface fitting with LED (Higher end) on false Ceiling or ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD 528)

Supply and fixing of 12W LED square type Recessed / Surface fitting with LED (Higher end) on false Ceiling or ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (Data 9)

Supply and fixing of 22W LED square type Recessed / Surface fitting with LED (Higher end) on false Ceiling or ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (Data 10)

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting (SD 535)

Supply and fixing of 60W LED street light fitting with LED (Lower end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting (SD 536)

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour . (SD 543 )

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW board with push switch (SD 105)

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 1 metre down rod on the existing fan clamp (SD 569)

Supply and fixing of 1400mm (56") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) on the existing fan clamp (18") (SD 575)

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall (SD 115)

Supply and fixing of 300 mm (12") sweep (Heavy duty) AC Exhaust fan complete without provision of wall opening. (Data 11)

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan (SD 120)

Supply and fixing of 375 mm (15") sweep (Heavy duty) AC Exhaust fan complete without provision of wall opening. (Data 12)

Supply and fixing of louvers shutters arrangements for 375mm (15") sweep (light duty) AC exhaust fan (SD 121)

Supply and fixing of 450 mm (18") sweep (Heavy duty) AC Exhaust fan complete without provision of wall opening. (Data 13)

Supply and fixing of louvers shutters arrangements for 450mm (15") sweep (light duty) AC exhaust fan (SD 123)

WALL SOCKETS

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (Set plug) (SD 476)

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD 488)

Supply and fixing of 2 no.6/16A two module socket , 2 no. 16A one module switch on suitable module surface mounting Box (Plastic) with module cover plate (plastic) on wall with connections. Higher End (SD 494)

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (SD 140)

Supply and fixing of 1 no.RG-06 (TV) socket with 1 module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End (Data 14)

Supply and fixing of 1 no.RJ-11 (Telephone) socket with 1 module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End (Data 15)

Supply and fixing of 1 no. 30A 2M Key fab on suitable module concealed Box (GI) in flush with wall with connections. Higher End (Data 16)

ELECTRIC WATER HEATER

Supply and fixing of 1500W automatic electric water heater of 35 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire but without plumbing connection (SD 104)

Run of Mains

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 55)

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. (SD 414)

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 57)

Supply and run of 4 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 61)

Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 63)

Supply and run of 3 core 2.5 sq.mm. (36 / 0.3) PVC insulated SC unsheathed copper cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with making good of the concealed portion with suitable colour (Data 17).

Supply and fixing of 6 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 4 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (Data 18)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 613)

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P RCCB as incoming and 24 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End ( Data 19).

Supply and fixing of 6 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P RCCB as incoming and 18 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (Data 20)

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A 4P RCCB 30mA as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End ( Data 21).

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P RCCB as incoming and 4 nos. 32A TMCB as outgoing in flush with wall with earth connection only. Higher End (Data 22)

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 125A 4P DPX MCCB as incoming and 4 nos. 63A TP MCB as outgoing in flush with wall with earth connection only. Higher End (For Power) ( Data 23).

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 125A 4P DPX MCCB as incoming and 4 nos. 63A TP MCB as outgoing in flush with wall with earth connection only. Higher End (For Lighting) ( Data 24).

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 125A 4P DPX MCCB as incoming and 8 nos. 63A TP MCB as outgoing in flush with wall with earth connection only. Higher End (Data L)

Supply and fixing of 12 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB as incoming and 4 nos. 6A to 32A TP MCB as outgoing in flush with wall with earth connection only. Higher End. (For domestic pump) (Data I)

EARTHING

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 233)

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soilsand to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers. (SOR M - 0827)

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry worK (SD 234).

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection (SD 76)

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection (SD 77)

Supply and run of 50mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.(SD-77 A).

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection (SD 458)

UG CABLES

Supply and laying of 2 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (SD 198).

Supply and clarnping of 2 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps (SD 216).

Supply and fixing of brass cable gland for 2 x 10 sq.mm. PVC armoured LTUG cable with earth connection (SD 182).

Supply and Laying of 50/38mm dia HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. ( Data 25).

Supply and laying of 6 core armoured OFC cable in existing HDPE pipe in ground (DATA 2)

supply and laying of 3 core 2.5 sq.mm PVC copper wire in existing HDPE pipe with earth connection. ( Data 26).

Supply and laying of 4C x 10 sq.mm.PVC LTUG Aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete and as directed by dept Officers.(SD 202).

Supply and clarnping of 4 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamp (SD 220)

Supply and fixing of brass cable gland for 4 x 10 sq.mm. PVC LTUG aluminium armoured cable with earth connection (SD 185)

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD 745)

Supply and Laying of 4 x 16sq.mm. PVC armoured LTUG cable EXISTING Trench. (SD: 203-56.30-52.66-140.28)

Supply and clamping of 4 x 16 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 221)

Supply and fixing of brass cable gland for 4 x 16 sqmm PVC armoured LTUG cable with earth connection. (SD 185)

Supply and providing cable end termination of 4x16sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 235)

Supply and Laying of 3½ x 25 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD 746)

Supply and clamping of 3½ x 25 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 222)

Supply and fixing of brass cable gland for 3½ x 25 sqmm PVC armoured LTUG cable with earth connection. (SD 186)

Supply and providing cable end termination of 3½ x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 235)

Supply and Laying of 3½ x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD 747)

Supply and clamping of 3½ x 35 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 223)

Supply and fixing of brass cable gland for 3½ x 35 sqmm PVC armoured LTUG cable with earth connection. (SD 187)

Supply and providing cable end termination of 3½ x 35sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 236)

Supply and laying of 3-1/2 x 70 sq.mm.PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete and as directed by dept Officers.(SD 207)

Supply and clamping of3-1/2 x70 sq.mm. PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 225)

Supply and fixing of brass cable gland for 3-1/2 x70 sq.mm. PVC armoured LTUG cable with earth connection. (SD 189)

Supply and providing cable end termination of 3½ x 70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 238)

Supply and laying of 3-1/2 x95 sq.mm.PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete and as directed by dept Officers.(SD 208)

Supply and clarnping of 3 1/2 x 95 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamp (SD 226)

Supply and fixing of brass cable gland for 3-1/2 x 95 sq.mm. PVC LTUG aluminium armoured cable with earth connection (SD 190)

Supply and providing cable end termination of 3-1/2 x 95 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 239)

Supply and laying of 3-1/2 x120 sq.mm.PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete and as directed by dept Officers.(SD 209)

Supply and clamping of3-1/2 x120 sq.mm. PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 227)

Supply and fixing of brass cable gland for 3-1/2 x120 sq.mm. PVC armoured LTUG cable with earth connection. (SD 191)

Supply and providing cable end termination of 3½ x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 240)

Supply and laying of 3-1/2 x150 sq.mm.PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete and as directed by dept Officers.(SD 210)

Supply and laying of 3-1/2 x150 sq.mm.PVC LTUG aluminium armoured cable in EXISTING trench (SD210 - 56.3-140.28-52.66)

Supply and clamping of3-1/2 x150 sq.mm. PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 228)

Supply and fixing of brass cable gland for 3-1/2 x150 sq.mm. PVC armoured LTUG cable with earth connection. (SD 192)

Supply and providing cable end termination of 3½ x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 241)

Supply and laying of 3-1/2 x240 sq.mm.PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete and as directed by dept Officers.(SD 212)

Supply and laying of 3-1/2 x240 sq.mm.PVC LTUG aluminium armoured cable in EXISTING trench (SD230 - 56.3-140.28-52.66)

Supply and clamping of3-1/2 x240 sq.mm. PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 230)

Supply and fixing of brass cable gland for 3-1/2 x240 sq.mm. PVC armoured LTUG cable with earth connection. (SD 194)

Supply and providing cable end termination of 3½ x 240 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 754)

Supply and laying of 2 RUNS OF 3-1/2 x300 sq.mm.PVC LTUG aluminium armoured cable in EXISTING trench (SD231 - 56.3-140.28-52.66)

Supply and clamping of2RUNS 3-1/2 x300 sq.mm. PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (2 X SD 231)

Supply and laying of 3RUNS 3-1/2 x300 sq.mm.PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete and as directed by dept Officers.(3 X SD 213)

Supply and clamping of3RUNS 3-1/2 x300 sq.mm. PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (3 X SD 231)

Supply and fixing of brass cable gland for 3-1/2 x300 sq.mm. PVC armoured LTUG cable with earth connection. (SD 195)

Supply and providing cable end termination of 3½ x 300 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 755)

Cable Tray

Supply and installation of sheet steel 2.5mm /2mm thick consisting 2 nos. side rail s with runs at every 250mm interval and complete with associated accessories such as coupler plates , Tees , long bend, elbows etc.Hot Dip Galvanized 65 microns tthick cable tray of size 35 x 35 x 5mm GI angle with 600mm width cable tray and 10mm threated GI rod supports upto 450mm with cable tray and they supports should be at 1.5m interval and grouting the supports in wall/ ceiling / floor as per the requirment in confimating with specification all as required size 150 x 50 x 2.0 mm thick ( Data 27).

LIGHTNING ARRESTOR

Supply and installation of Early stemer Emmission air terminal (ESEAT) model S . The ESEAT- has corrossion resident stainless chrome body made up of AISI 316 grade of height 0.50 metres cablable of working in hazardous atmoshphere . The Air teminal is Non- radioactivity and requires no special license. The Unit is fully atonomous (No battery, No external power is required) Collects energy from ampient electric field . The ESEAT model has been tested in a High voltage laboratory in accurancy with NFC 17102 in order to measure the average gain in triggering .The averge gain in triggering time Δ T S (obtained during the lab test for the offered model is 60 μ sec. The ESEAT works on negative as well as positively polarised discharge . ESEAT has been tested for such discharge in central power research institute (CPRI) . A dedicated tester is available to test the healthness of the ESEAT on request (Page no.37, Point no.3 of causes 8.6 of the revised NFC 17 -102 version 2011. ESEAT model -s rarius of protection 46 metre . Level of protection cosidered for the project 2 level ( SOR M-2140)

Mounting Structure Supply and Installation of standard /special mounting structure of height 4.5 metres. Pipe and 300 x 300 x 80 mm MS plate , 3 metres 48mm OD class C GI outer pipe , 1.8m, 38mm OD inner pipe , for roof mounting on concret base and with FRP adopter. (SOR -M-2141)

Down Conductor Supply and clamping of 1 x 70 sq.mm SC flexible multistrand unarmoured copper cable in Suitable HDPE pipe on wall/ ceiling/ roof top etc. with MS clamps. ( Data 28)

TEST Link supply and Installation of Test link box for each down conductor in order to disconnected the earth termination system to enable measurement of resident ( Data 29)

Earth Electrode supply and Installation of maintenance free GI earthing system comprssing of 50mm dia and 2 mtr. Length earth electrode of low carbon steel rod with100 micron bonding and 25 kg. of carbon based environment friendly back fill compound and suitable clamp. (SOR M 2144)

Surge Protection Supply and installation cabinet type class I &II cabined model SPD to arrest surge and over voltage in the power line due to lightining switching action etc.They must be installed in the incoming MCCB panel/ DB of the respective Building in parrallel to the power circuit (Model PSV 4 -12.5/400TT) (3 phase power network) (SOR M 2145)

Supply,Installation , testing and commisioning of 2 MP IR Fixed Dome Network Camera with following specifications. Protection Ingress protection: IP67 (IEC 60529-2013), IK10 (IEC 62262:2002). All complete complying with relevant standard specification (Higher end) Specification: Image Sensor: 1/2.8" Progressive Scan CMOS Max. Resolution: 1920X1080 @30fps Min. Illumination: Colour: 0.028 lux @ (F2.0 AGC ON) B/W: 0 Lux with IR Lens: 2.8/4/6mm Fixed Lens Three Stream Wide Dynamic Range (WDR): Digital WDR Image Enhancement: BLC, HLC, 3D DNR (Data 30)

Supply,Installation , testing and commisioning of 5 MP Fixed Bullet Network Camera, with Built-in microphone for real-time audio security, Water and dust resistant. Protection Ingress protection: IP67 (IEC 60529-2013), IK10 (IEC 62262:2002).All complete complying with relevant standard specification (Higher end) Specification: Image Sensor: 1/2.7" Progressive Scan CMOS Max. Resolution: 2560X1920 Min. Illumination: Colour: 0.005 lux @ (F1.6 AGC ON) B/W: 0 Lux with IR Lens: 2.8/4/6mm Fixed Lens Three Stream Wide Dynamic Range (WDR): 120 dB Image Enhancement: BLC, HLC, 3D DNR ( Data 31)

Supply installation Testing and Commissioning of PTZ 4 MP ColorVu Network Speed Dome with Clear imaging against strong back light due to DWDR technology, 3D DNR technology delivers clean and sharp images with following specifications: Protection IP66: IEC 60529-2013. All complete complying with relevant standard specification (Higher end) Specification Camera: Image Sensor: 1/1.8" Progresssive Scan CMOS Max Resolution: 2560X1440 Min. Illumination: Colour: 0.001 Lux @(F1.0, AGC ON), 0 Lux with Light Lens: Focal Length: 2.8 mm/4 mm PTZ Movement Range (Pan): 0 deg to 340 deg Movement Range (Tilt): -5 deg to 105 deg Pan Speed: Configurable from 4 deg to 21 deg/s Tilt Speed: Configurable from 4 deg to 19 deg/s Image: Wide Dynamic Range (WDR): Digital WDR Interface: Ethernet Interface: 1 RJ45 10 M/100 M self-adaptive Ethernet port On-board Storage: Built-in memory card slot, support microSD/SDHC/SDXC card, upto 256 GB Built-in Microphone: Yes ( Data 32)

Supply installation Testing and Commissioning of 64 channel 8K Network Video Recorder with following features. All complete complying with relevant standard specification (Higher end) Up to 64-ch IP camera inputs Up to 2-ch@32 MP + 2-ch@8 MP/10-ch@8 MP/20-ch@4 MP/40-ch@1080p decoding capacity Up to 400 Mbps incoming bandwidth and 400 Mbps outgoing bandwidth 2 HDMI (different source) and 2 VGA (different source) interfaces, 8K or dual 4K video outputs Supports RAID 0, 1, 5, 6, 10 and N+M hot spare for even more reliable data storage, effectively avoids data loss risks Redundant power supply Provide independent HDMI and VGA outputs HDMI video output at up to 8K or dual 4K resolution 8 SATA interfaces for HDD connection (up to 16 TB capacity per HDD) 1 eSATA interface for HDD connection 16-ch synchronous playback Support multiple VCA (Video Content Analytics) events Configurable special camera smart functions, such as VCA detection (motion, line crossing, intrusion, etc.), heat map, ANPR, and people counting 2 self-adaptive 10/100/1000 Mbps Ethernet interfaces ( Data 33)

Supply and Laying of 50/38 mm dia HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (Data -1)

Supply and laying of 6 core armoured OFC cable in existing HDPE pipe in ground (Data 2)

Supply and Installation of 4U rack with accessories(Higher End) for 24 port POE switch

Supply and fixing of 65mm dia GI pipe (Class 'B') of 4 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom and with concreting and construction on masonary pedestal with MS box of 30cm x 20cm x 10cm with angle iron frame work with door with lock and key arrangements and with suitable AI cross arm with clamp set and painting of suitable colour (Data 3)

Supply and Installation of 8 TB Survellance Hard disk. (Higher end)

(Data -4) Supply and installation of 24 port POE switch (Higher end) for CCTV IP camera

(Data -5) Supply and installation of RJ 45 I/O socket with PVC modular and dual face plate

(Data -6) Supply and laying of unarmoured CAT6 cable in existing PVC pipe in wall

Supply and installation of Fiber Media Convertor T10/100, fiber optic patch cord with RJ45 connector (Higher End)

Supply and run of 20mm dia PVC rigid pipe concealed in wall/cealing for CAT6 cable (indoor)

Supply, Installation of 43 inch LED 24x7 operational display with necessar assecories for mounting on the wall (Higher End)

ACCESS CONTROL SYSTEM

Supply, fixing and Installation of Face And Fingerprint Biometric Reader with communication interface of WIFI,TCP/IP,RS232/485 and USB , and 1GHz High Speed CPU Processor , 125kHz EM RFID Card ,4.3" touch Screen 480x272 Pixel LCD ,16 bit Hi-Fi Voice & Sound Indication Brand: BioMax/ Equivalent etc complete complying with standard specification and as directed by the departmental officers

Supply,fixing and Installation of S-Tech EPABX Machine CS416 for Main Trunk Lines and 50Extension Telephone Intercom SystemCapacity: 4 Main Lines (Trunk Line/ P and T) and 50 Extension ,Internal/External Music on Holding, Operator/Auto-attendant Mode, Remote Programming Day/Night Mode(Manual), Music & Ringing Recordable OGM(outgoing message), Music Duration 20 Seconds Caller ID, Call Transfer, Call Forwarding Manually, Outgoing Call Transfer, Power Failure Transfer, Specific Main Line (C.O./Trunk Line) Dialing, Three Way Conference, Do Not Disturb, Auto/Manual Dial-Out Mode Brand: S-TECH / Equivalent etc complete complying with standard specification and as directed by the departmental officers

Supply and Installation of LAN NET WORK switche: Fully Managed 10/100/1000 Layer -3 with 10G Uplink -24 Port with Fibre port ( Data 34)

Supply and Installation of I/O socket , Face plate dual socket RJ45 with CAT6 PVC module Box ( Data 35)

Supply and installation of 9U Rack with accessories (Higher end) ( Data 36)

Supply and Installation of 3 metre lenght Patch cord (Higher end) ( Data 37)

Supply and installation of WiFi 6AX 1500 Mbps Archer AX10, smart WiFi, Triple core CPU, Gigabit, Dual -Band Wireless router (Higher end) ( Data 38)

Supply and laying of unarmoured CAT6 cable in existing PVC pipe in wall ( Data 39)

Supply and run of 20mm dia PVC rigid pipe concealed in wall/cealing for CAT6 cable (indoor) ( Data 40)

11 KV OUTDOOR VACCUM CIRCUIT BREAKER Supply Erection,testing and commissioning of 11KV, 25KA, 630Amps HT OUTDOOR THREE PANEL VACCUM CIRCUIT BREAKER For Consumer POS With 18KV, 10kA Polymer Type Surge Arrester. Horizontal Draw Out VCB fitted with Manual / Motor Operated spring charging mechanism with 230V AC Motor & Motor Control Switch, Mechanical ON/OFF indicator Operation Counter, Automatic safety shutters & push Shunt trip Coil, 110V DC. Closing Coil, 110V DC. Spare auxiliary contact, 6NO+ 6NC. Anti pumping Feature, 110V DC. Power pack 230V- 110V AC/110V DC Potential Transformer, Three Phase, Resin cast, Dry type, Fixed Potential transformer with one set of HTFS/LTFS and one no. Neutral Link of Ratio: (11KV/V3)/(110V/V3) Current Transformer, Single phase, Resin Cast, Dry Type Current Transformer, Core 1: for meter, Cl-0.5s, 5VA, Core 2: for protection, Cl-5P20, 15VA. Metering, MFM, Digital Ammeter & Digital Voltmeter With Fault Level tripping & Fault Recording. Protection, Numerical Non-directional IDMT. (M - 1954) Including Civil work for RMG plinth of height 150mm foundation 7.5m x 1.55m x 150mm, liasioning charges for TNEB MRT Higher official inspection at manufacturing unit factory, Transportation charges and Erection , testing and commissioning charges. ( Data 42)

HT CABLES

Supply and Laying of 300 sq.mm. 3 core HT XLPE 11KV (E) SISMV11U3 x 3002424 armoured cable in suitable size RCC cable truf in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. ( Data 43)

Supply and clamping of 300 sq.mm. 3 core HT XLPE 11KV (E) SISMV11U3 x 3002424 armoured cable on post or on wall with MS Clamps. ( Data 44)

Supply & Fixing of 300 sq.mm. 3 core HT Cable Indoor Terminations XLPE 11KV (E) - Belted PILC Cables - EPKT 4961 .( Data 45)

500KVA TRANSFORMER Supply erection testing and commissioning of 500KVA/11KV /433V off load tap changing copper wound outdoor type distribution transformer conforming to relevant ISI 180 Level -2 standard and fitted with the following: a)HV cable end box suitable for Connection 3 core 300 Sq mm 11 KV, XLPE HT cable b) LV cable end box suitable for connection 3 runs of 31/2x400 Sq mm LTUG Cable c)Conservator with shut off valve d) Conservator drain plug valve e) Dehydration silicagel breather f) Expansion vent g) 4Nos plain rollers H) Thermometer pocket with dial type thermometer with caillary tubing with maximum reading position. i) Drain plug/valve) Filter valve j) Oil filling hole and cap k) Oil level gauge l) two body earhing terminals m) Rating and terminal marking plate n) Lifting hooks /lifting eyes,jacking pad to facilitate movement of transformer and easy handiling-1 No (Each) n) OFF load hand opereted tap changing switch at standing height from ground level. o) Tapping on primary widing for voltage and vaiation 5% to +5% p)Neutral on LV side to be available for 4 wire supply and brought out thought bushing for earthing q)Air release device r)The transformer should be supplied with first filling of oil All removable cover shall be provided with weather proof hot oil from the tank Sakthi/Rowson /Voltech /IPL )/35i Eco power/eq Including Charges for civil work and unmovable for the transformer wheel arrest for AI frame work with fixing on the transformer 100mm x 50mm channel provided, Transportation and transit insurance @2%, Erection , testing and commissioning charges with Test report ( Data 46)

MAIN MV PANEL

Supply, erection, testing and commissioning of 800A draw out type floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following with Thermal Magnetic Release MCCB’s and 2 Nos. ACB as Incomer units , with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4Nos.2Runs 2” X 1” tinned copper bus bar for 3 phases and neutral (2x 50mm x 12mm) and 2 Nos. of ear thing bus of size 1” X 1/4 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creep age distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set Incoming 1)Supply and fixing of 2 No. 800A 4 pole 50 ka , microprocessor based, EDO/MDO breaker 433V LT ACB confirming to IS 13947–2 IEC 60947–2 with suitable capacity with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with Micro processor Based SR 18 G relay, over current trip device adjustable to LTD, STD andrelease for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout, features, separate mold base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, IE rules in force with inter connection and terminations as required in specification. Bus Coupler:- Supply and fixing of 1 No 1600A basic rating 4 pole 433 VLT ACB to IS-1394721EC60947-2 600VAC with all accessories for standard horizontal type ACB equipped withMicroprocessor based SR18G(w/o protection). Outgoing 1) Supply and fixing of 630A 4 Pole ACB -2Nos 2) Supply and fixing of 400A FPN MCCB-6 Nos. 3) Supply and fixing of 250A FPN MCCB-2Nos. 3) Supply and fixing of 63A FPN MCCB-2Nos Inter connecting the all LT ACB’s and MCCB’s to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve color coding of phases and neutral indication. Double Earth connection of the MCCB’s and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1”X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules with , 2 sets, of supply and fixing Electronic Trivector EC,300N class 0.5 flush mounting L&T or equivalent make–ModelER300N.Supply and fixing of danger board withSiemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel, concreting ,testing andcommissioning (L&T,C&S,SIEMENS,ABB) ( Data 47)

AUTOMATIC POWER FACTOR CORRECTION

RELAY PANEL (APFCR PANEL)

Supply and erection of 200 KVAR 415/440Volts 50Hz 3 Ph automatic power factor correction panel, 9 stage, (at 0.95 lag), made up of powder coated, 16 SWG CRCA sheet steel enclosure with 1 1/2" x 1 1 1/2" x 1/2" AI Frame work with RCC concreting foundation and bolted to masonry pedestal with Delta Connected capacitors (BCH/EPCOS) MOO Type operating in multiple stage with 3 current and Voltage Transducers (CVT) at the phases simultaneously to activate the desired power factor switching time between steps 120 seconds, switching off time in case of fault 3 seconds with a LCD display to show the following Parameters. a. Vr – R phase Line Voltage b. Vy – Y phase Line Voltage c. Vb – B phase Line Voltage d. Ir – R phase Line current e. Iy – Y phase line current f. Ib – B phase Line Current g. KW – Present Kilo Watts h. RKVA – Present KVAR Demand i. KVA – Present KVA j. PF – Present Power Factor k. Number of Capacitor bank ON/OFF l. Provision to indicate the imbalanced load m.Provision to indicate the change in phase Sequence n. The APFC Panel Should also have built in protection for current imbalance. For high Voltage/Low Voltage cut off, single phase Preventer, provision for inductor coil to cater the in-rush currents, line surges, Current Limiters, Current Sensor, etc., with connection complete and as per the relevant IE Rules. Eight Stages of Automatic Power Factor control panel with necessary connection. Make. (Matrix /L&T /or equivalent ( Data 48)

ESSENTIAL PANEL ESSB-1 Supply, erection, testing and commissioning of 630A draw out type floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following d sine with Thermal Magnetic Release MCCB’s and 1 No. ACB as Incomer units with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4Nos.2Runs 2” X 1/2” tinned copper bus bar for 3 phases and neutral (2x 50mm x 12mm) and 2 Nos. of ear thing bus of size 1” X 1/8 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creep age distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set Incoming 1)Supply and fixing of 1 No. 630A 4 pole 50 ka , microprocessor based, EDO/MDO breaker 433V LT ACB confirming to IS 13947–2 IEC 60947–2 with suitable capacity with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with Micro processor Based SR 18 G relay, over current trip device adjustable to LTD, STD andrelease for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout, features, separate mold base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, IE rules in force with inter connection and terminations as required in specification. Outgoing 1) Supply and fixing of 400A FPN MCCB-3Nos 2) Supply and fixing of 250A FPN MCCB-3Nos. Inter connecting the all LT ACB’s and MCCB’s to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve color coding of phases and neutral indication. Double Earth connection of the MCCB’s and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1”X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules with , 2 sets, of supply and fixing Electronic Trivector EC,300N class 0.5 flush mounting L&T or equivalent make–ModelER300N.Supply and fixing of danger board withSiemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel, concreting ,testing andcommissioning (L&T,C&S,SIEMENS,ABB) ( Data 49)

ESSB-2 AND 3 Supply , Erection Testing and commissioning of 415V/50 HZ 250A Cubical panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/2 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 400A 4P MCCB -1no. 125A 4P MCCB - 4nos. ( Data 50)

SSB-1 AND 2, AC PANEL, 250A Panel Supply , Erection Testing and commissioning of 415V/50 HZ 250A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/4 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 250A 4P MCCB -1no. 125A 4P MCCB - 4nos. ( Data 51)

POWER SWITCH BOARD 2 (FIRE PUMP) Supply , Erection Testing and commissioning of 415V/50 HZ 250A Cubical panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/2 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 400A 4P MCCB -1no. 400 Amps TPN MCCB of 35kA(Ics) withstanding capacity with FOD, Adjustable Overload, Fixed Short Circuit Relays - 1 Set 160 Amps TPN MCCB of 25kA(Ics) withstanding capacity with FOD, Adjustable Overload, Fixed Short - 3Nos 63 Amps TPN MCCB of 25kA(Ics) withstanding capacity with FOD, Adjustable Overload, Fixed Short - 3Nos ( Data 52)

VRF PANEL-1,2, UPS O/G-1,2, EAST WING POWER PANEL, VIP ESSP.

Supply , Erection Testing and commissioning of 415V/50 HZ 125A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/4 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 125A 4P MCCB -1no. 63A 4P MCCB - 4nos. ( Data 53)

PUMP PANEL

Supply , Erection Testing and commissioning of 415V/50 HZ 125A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/4 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 125A 4P MCCB -1no. 63A 4P MCCB - 6nos. ( Data 54)

125A Panel (Outdoor Pillar Panel) Supply , Erection Testing and commissioning of 415V/50 HZ 125A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/4 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 125A 4P MCCB -1no. 63A 4P MCCB - 4nos. The above panel house in suitable CRCA sheet steel box with Door & Lock & Key arrangement with suitable leg support & powder coated painting. ( Data 55)

250A Panel (Outdoor pillar Box)-OAT Supply , Erection Testing and commissioning of 415V/50 HZ 250A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/4 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 250A 4P MCCB -1no. 125A 4P MCCB - 1nos. 63A 4P MCCB - 5No. The above panel house in suitable CRCA sheet steel box with Door & Lock & Key arrangement with suitable leg support & powder coated painting. ( Data 56)

Supply and ,Erectionof Outdoor Pillar box made up of 16 SWG CRCA sheet steel ( Length 900mm x Height 1200mm x width 600mm) with door and lock & key arrangements on suitable angle iron frame support for floor /wall mounting support to house the Vertical 4 way TPN MC B Distribution board as detailed below Incoming - 63A 4P MCB -1 no., Outgoing - 32A 3P MCB -3 nos., 6A -32A SP MCB -3 nos. ( Data 57)

LTCT METER BOX- OUTDOOR TYPE Supply ,Erection ,Testing and commissioning of Three compartment 400A LTCT meter box made up of 16 SWG CRCA sheet steel ( Length 1200mm x Height 1200mm x width 600mm) with door and lock & key arrangements on suitable angle iron frame support for floor / wall mounting support with supply and fixing of the following interior mounting arrangements with busbar chamber, meter chamber and Terminal box chamber confirming to IE rules. i.The busbar chamber will consist of 4 nos. 2” x 1/4” tinned copper flat for phase and neutral busbar on epoxy mounted bus insulated at proper and sufficient spacing between the bus bar as per IE Rules. ii. 3 nos. 400/5A CT coil mounted in Three phase busbar. iii. Interconnection between CT coil to 4 way terminal box and 4 way terminal box to Meter box by 4 sq.mm PVC cu.wire. The LTCT meter box should be powder coat paint of approval colour , approved by site officer. (Data -33)

400A Panel Supply , Erection, Testing and commissioning of 415V/50 HZ 400A Cubical panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/2 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 400A TP ATS - 1no. (SD742) 400A 4P MCCB -1no. 125A 4P MCCB - 4 nos. 63A 4P MCCB - 5 nos.

Supply and fixing of 400 A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only. (SD 726)

supply and fixing of 6 metre lenght single bracke GI steel tubular pole with base plate 250 x 250 x 6mm OD 76.10mm 3.65mm thick x 6000mm length with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour ( Data 58)

Supply & Fixing of coil earth to street light poles with 8SWG GI wire of 11.5m of length in which 10m of total length compressed in coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the Earth.

supply and fixing of Aesthetically designed decorative hot dipped galvanised mild steel step pole with grey powder finish and 3 meters hight and 72 mm of Dia. Compatible for Higher end post top range. Window - Plasma cut & duly chamfered opening window of 300x110 mm for terminal connections & mounting accessories. Window cover is fitted with allen screws to the pole. Decorative sleek casting ring to increase aesthetical appeal. with bottom concrete and construction of masonry pedestal with supply and fixing of Aesthetically designed IP 65 50W LED post top (Higher end) with aluminium enclosure, powered with high power LEDs as light source and die casted heat sink exhibits classic Victorian look with symmetrical light distribution and excellent heat dissipation for long life with connections complete. ( Data 59)

Design, Supply, erection, Testing, Commissioning and handing over of 12 metre Mini Mast Structure (Bajaj / Philips / Crompton make or equivalent) with required number of continuously tapered hot dip galvansied steel polygonal side sections with telescopic strip joints to a total of 12 meters capable of sustaining the maximum wind pressure at the erection site with single flange base mast section with vertically moveable hot dip galvanised lantern carriage and accessories such as electrical junction box brackets for providing 6 Nos of 150W LED flood light luminaries with control gear box complete head frame assembly, pulley drive stainless steel wire rope single / double drum self-lubricating winch arrangements suitable for raising and lowering the luminaries carraige ring flexible multi core power cable and necessary high tensile hot dipped galvanized foundation, bolt & nuts along with washers and templates including supply and fixing the following accessories in the Mast design and casting of suitable foundation with 1:2:4 mix RCC concreate with 30cm projection above the ground level with 1 mtr width x 1mtr length x 2 mtrs depth with necessary galvanised foundation bolts nuts and washers and dump plates enclosing the bolts nuts for high mast cosidering the safe soil bearing capacity at site-1 Setb) High powered power tool with complete with hand held control panel and motor with push button type remote control switch suitable for 3 phase 415 V /50 HZ for raising and lowering of the lantern carriage complete to operate all fittings mounted in the base to couple with winch-1 SET c) Feeder pillar box comprising of 0.90m x 0.45m x1.20m floor angle iron frame with 63 A power contactor starter for the 3 Phase motor-1Set d) Neon aviation obstruction light (Bajaj/equivalent) - 1No. e)2Nos of special GI earth electode with copper plate 300 x300x3mm and copper flat (1"x1 1/4")inter connection as per ISS complete with earth connections-1SET f) Hot dip galvanised lighting arrester- 1 No) ( Data 60)

supply and fixing of 5W LED down light (Higher end) (Vallalar lamp) with suitable steel rope suspension with connection. ( Data 61)

Supply and fixing of 100W LED flood light (Higher end) with integerated driver on suitable special AI frame support with conection. ( Data 62)

supply and fixing of Environmental friendly, new generation, energy saving, decorative IP66 15 W LED facade light using COB LED as light source on suitable support with connection. ( Data 63)

supply and fixing of Environmental friendly, new generation, energy saving, decorative IP66 5 W LED facade light /UP-DOWN light using COB LED as light source on suitable support with connection. ( Data 64)

SECTION – A : VRF EQUIPMENT ( INDOOR & OUTDOOR UNIT )

VARIABLE REFRIGERANT FLOW OUTDOOR UNITS (VRF ODU): Supply Installation,Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating,having all hermetically sealed inverter type Scroll Compressor(s),minimum two compressors for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R410A Refrigerant, vibration isolators, with suitable foundation etc. complete as required.The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping.The unit shall be suitable to work on 400V+/10%, 3Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required.The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5

30 HP (SOR M 2024)

16 HP (SOR M 2031)

High wall VRF AC units

VRF INDOOR Unit Installation: Supply, Installation, testing and commissioning of HI- wall split Indoor unit of the following capacities with matching VRF system, the unit completely tested and included factory wiring, piping, sysnthetic washable media prefilter, fan section with low noise multi speed fan motor and dynamically balanced blower, coil section with DX copper coil, electronic propotional expansion valve along with pump to control the refrigerant flow rate responding to variatiobs of the air conditioning load of the room, 360 degree air flow discharge, control circuit board, presence and flow sensor, auto cleaning panel thermal detector, condensate drain pan, self diagnostics auto restart function, test run switch, drain pipe and outer cablinet, nescessary supports, vibration isulation, cordless remote control etc. suitable for operation of 230 volt 50hz, single phase ac supply complete as required. The unit shall have an auto swing louver which ensures efficient air distribution which closes automatically when the unit stops. The front grille shall be easily removed for washing. The remote controller shall be able to set five steps of discharge angle. The discharge angle shall be automatically set at the same angle as the previous operation upon restart. The drain pipe can be fitted to from either left or right sides. The indoor unit and the refrigerant pipes shall be charged with dehydrated air prior to shipment from factory. Both refrigerant lines shall be insulated from the outdoor unit to indoor unit and return air shall be through a resin net mould resistant filter. The unit shall have automatic force shut provision in case of fire on receiving signal from BMS system.

1.5 TR High wall indoor unit

2.0 TR High wall indoor unit

Supply of Carrier Make 1.0 TR Capacity Brand-EMBERIA-CX 3 Star Value. Blue Coated Evaporated Coil, With Aqua Clear protection outdoor unit With temperature Display on the Indoor Unit. Non-Inverter Hi-Wall mounting energy efficient Split type AC unit consisting of outdoor condensing unit complete with cmpressor and air cooled condenser with fan motor & Fully remote control operation etc., including initial charge of gas and suitable for single phase AC, (230V, 50HZ, AC) Model Make:Carrier,(3 Star Rated)

Supply of Carrier Make 1.5 TR Capacity Brand-EMBERIA-CX 3 Star Value. Blue Coated Evaporated Coil, With Aqua Clear protection outdoor unit With temperature Display on the Indoor Unit. Non-Inverter Hi-Wall mounting energy efficient Split type AC unit consisting of outdoor condensing unit complete with cmpressor and air cooled condenser with fan motor & Fully remote control operation etc., including initial charge of gas and suitable for single phase AC, (230V, 50HZ, AC) Model Make:Carrier,(3 Star Rated) ( SOR M1984 )

Supply and fixing of 4KVA double boost wall mounting type Automatic voltage stabilizer with time delay, low & high cut off arrangements suitable for operation on 230V/50C/S, AC supply. V-Guard. (SOR M1988)

Supply and fixing of Condenser Angle iron stand suitable for 1.5 & 2.0 TR outdoor unit (SOR M1991)

Supply and laying of 5/8" & 3/8" Copper Refrigerant pipe along with nit rile rubber insulation hose and pvc non adhesive white tape. (SOR M1990)

SECTION- B : REFRIGERANT PIPING AND PVC CONDESATE PIPING

41.3 mm dia with 19 mm thick insulation

34.92 mm dia with 19 mm thick insulation

31.75 mm dia with 19 mm thick insulation

28.57 mm dia with 19 mm thick insulation

25.4 mm dia with 19 mm thick insulation

22.2 mm dia with 19 mm thick insulation

19.05 mm dia with 19 mm thick insulation

15.87 mm dia with 19 mm thick insulation

12.52 mm dia with 13 mm thick insulation

9.52 mm dia with 13 mm thick insulation

6.35 mm dia with 13 mm thick insulation

PVC CONDENSATE PIPING: Supply,installation,Testing & Commissioning of Heavy duty PVC pipes of following sizes; with 9mm thick Aluminium Foil faced Nitrile Rubber Insulation

25mm Dia

32mm Dia

40mm Dia

SECTION – C : DUCTING AND AIR TERMINALS

FACTORY MADE RECTANGULAR GI DUCTING : Supply, installation, testing and commissioning of factory made lock-forming quality rectangular GI ducting, complying with IS: 277 and having 120 GSM coating classification. The price include the cost of necessory accessories & supports (like TDF flanges, ms angle flanges, neoprene gaskets, threaded rod, corner saddles, guide vanes as per SMACNA standards, joints, labelling etc..

24 Gauge ( 0.63 mm Thick ) (SOR M2006)

22 Gauge ( 0.8 mm Thick) (SOR M2007)

20 Gauge ( 1.0 mm Thick) (SOR M2008)

FACTORY MADE FLAT OVAL GI DUCTING : Supply, installation, testing and commissioning of factory made lock-forming quality Flat Oval GI ducting with Inner Thermal Insulation, complying with IS: 277 and having 120 GSM coating classification. The price include the cost of necessory accessories & supports (like TDF flanges, ms angle flanges, neoprene gaskets, threaded rod, corner saddles, guide vanes as per SMACNA standards, joints, labelling etc..

24 Gauge ( 0.63 mm Thick ) (SOR M2006)

22 Gauge ( 0.8 mm Thick) (SOR M2007)

SEMI RIGID DUCT: Supply, installation, testing and balancing of Semi Rigid duct as per above specification.

150 mm Dia

SUPPLY AIR ROUND DIFFUSER: Supply, installation, testing and balancing of aluminum powder coated circular / square diffuser with collar damper as per approved shop drawings and with standard flange size.

300 mm Dia

GRILLES: Supply, installation, testing and balancing of aluminum powder coated grilles as per approved shop drawings and specifications with standard flange size. Note: the grille colour shall be as per the client/architect requirements (SOR M2009)

LOUVER : Supply, installation, testing and commissioning of extruded Aluminium powder coated Fresh air & Exhaust air louver. The color & pattern shall be pre-approved by Architects/Client.

DOOR TRANSFER AIR GRILLES: Supply, installation, testing and commissioning of aluminium powder coated grilles with standard flange size.

ROUND DISC VALVE: Supply, fixing and testing of Al. powder coated Round disc Valve of 150 mm dia for Toilet Exhaust with damper.

COLLAR DAMPERS: Supply, installation, testing and commissioning of aluminium collar damper to be mounted for grilles & diffusers.

FIRE-RETARDANT CANVASS: Supply, installation, testing and commissioning of fire-retardant canvss, with GI matching flanges, with a provision of operable zip. The entire assembly shall be fabricated at factory. (SOR M2004)

SPICOT DAMPER: Supply and installation of GI Spicot Damper

150 mm Dia

VOLUME CONTROL DAMPERS: Supply, installation, testing and commissioning of Factory fabricated Rectangular shape Aero foil type Aluminium volume control dampers, 1.2-mm Al Frame, 1.0-mm, 150-mm width, with required hardware and accessories. Stiffen damper blades for stability. Include locking device to hold single-blade dampers in a fixed position without vibration & engraved marking on position of damper, as per specifications. The shafts shall be suitable to mount electric actuators, where-ever required. Dampers' flanges shall be suitable to TDF. Please refer technical specifications for complete details and scope & quote accordingly.

BACK DRAFT DAMPERS: Supply, installation, testing and commissioning of Factory fabricated Rectangular shape Aero foil type Aluminium volume control dampers, 1.2-mm Al Frame, 1.0-mm, 150-mm width, with required hardware and accessories. Stiffen damper blades for stability. Include locking device to hold single-blade dampers in a fixed position without vibration & engraved marking on position of damper, as per specifications. The shafts shall be suitable to mount electric actuators, where-ever required. Dampers' flanges shall be suitable to TDF. Please refer technical specifications for complete details and scope & quote accordingly.

FIRE DAMPERS: Supply, installation, testing and commissioning of Fire dampers with fusible link, 1.5-hours fire rating, for supply ducts and return air duct where-ever crossing the space separating walls or as shown in the drawings. The damper shall be made out off 1-mm thick gal vanished Sheet metal blades, with 1.4-mm thick Galvanized sheet frame, Fusible link Fire dampers, 1-mm thick gal vanished Sheet metal blades, with 1.6-mm thick Galvanized sheet frame.

MS SUPPORT WORK: Supply, fabrication and installation of mild steel support work for support works as per the drawing , other than for duct, pipe and equipment supporting. The supports should be duly painted using two coats of primer and two coats of black enamel paint. (Quotation enclosed)

SECTION – D : INSULATIONS

DUCT ACOUSTIC INSULATION : Design, Manufacture, Supply, Installation, Testing, and Commissioning of Open cell Nitrile rubber for Acoustics , of Class-1 with Ultrafresh Antimicrobial protection as per ASTM G21, ASTM G22, UL-181 and E2180 , FM Global, Density 140-180Kg / m3, UL94 approved (HBF, HF 1 & HF 2) in accordance to UL 94,1996.Thermal conductivity 0.047 W / MK at 20 Deg C, Air Erosion Resistance test Confirming to ASTM Standard C 1071-05 (section 12.7). For application use Low Voc Adhesive. thickness as per specification. [ for duct linear=15mm thk ] Note - if the adhesive is not self adhiesive type then the glue should be used with the same manufacturer.

10mm Thick

UNDERDECK INSULATION : Supply, installation, testing and commissioning 13mm thickness of closed cell nitrile preformed sheet insulation without Aluminium foil for underdeck insulation with support like round insulation disc and cross steel wire. Adhesive shall be used as recommended by insulation manufacturer for applying over concrete structures.

SECTION – E : FANS

CABINET FRESH FAN: Supply, installation, testing and commissioning of Ventilation fan cabinet type units. The unit shall be 0.6mm GIS construction, belt driven centrifugal fan, High efficiency motor, spring vibration isolator for fan and motor, Fire retardant canvass connections, with acoustic enclosure for fan & noise level not exceed 65 dBA at 1.5m distance,weatherproof type, internal power and control wiring, GI base frame complete as per specifications as required. Fan motor shall be suitable for 415±10% volts, 50Hz, 3 phase AC supply & & 230V, 1 phase, 50Hz AC supply.

Air Qty: 2210 CMH, ESP: 15mmWC

INLINE EXHAUST FANS: Supply, Installation, testing and commissioning of factory-fabricated, assembled,tested, and finished, direct-driven circular / Rectangular fans consisting of internally lined housing, wheel, fan shaft, bearings, motor, drive assembly, with joints between sections sealed. The mounting frame will be Galvanized Steel frames of minimum 3-mm Thick with factory fabricated corner pieces.

Air Qty: 1700 CMH, ESP:15mm WC ( Toilet ,Electrical Room, Low Voltage Room)

AXIAL FAN : Design, Supply, installation and commissioning of the following capacity Axial Flow Fans with silencer length is equal to fan dia. The fan motor shall be suitable for operating on 415±10% V, 3 phase, 50Hz AC supply. The cost shall inclusive of required length and adequate power wiring from the nearest isolator to the fans, weatherproof, wall housing, Fire retardant canvass connections, vermin net on both sides, louvers on one end, steel supports required for mounting the fan and bird screen, wire mess and storm proof louvers as required

Air Qty: 19550 CMH, ESP: 25mmWC , Motor Rating: 11KW (Quotation enclosed)

Supply, installation, testing and commissioning of Pressure Sensor located at Pressurized Room to maintain the pressure.The sensor shall be microprocessor based and shall incorporate suitable measurement techniques to be capable of generating an output signal proportional to the pressure achived the signal need to transmit to close the damper & maintain the fan Speed. (Quotation enclosed)

320 KVA DG

Supply, Erection, Testing, Commissioning and Handing over of 1 No 320 KVA Diesel Generator set of 0.8P.f, Three Phase, 415/420Volts, 50c/s, 1500RPM as detailed below with AMF panel. 1.ENGINE: Water cooled Diesel engine suitable for generator application with a shaft Output of 400 BHP at 1500 RPM under NTP Condition as per BSS 5514/IS 10000. The engine shall comprise the following standard scope of supply: (Make Kirloskar/ Cummins/ Ashok Leyland/ reaves/ Equivalent) 1. Dry type Air cleaner 2. Expansion bellow 3. Radiator, Radiator fan and mounting 4. Air to air charge cooler 5. Exhaust Gas turbo charger 6. Lube oil cooler and Lube oil filter 7. Fuel filter(pre and micro 8. In-line Mono-block fuel injection pump with governor and fuel feed pump 9. Electronic governor 10. 24V Battery charging alternator 11. 24V Volt electric starter motor 12. Engine test Certificate 13. Residential Mufler 14. Fly wheel with starter ring. ENGINE INSTRUMENTPANEL MOUNTED. Engine control panel consisting of ON/OFF/START Key Lube oil pressure guage , oil temperature gauge, high water temperature guage and electronic hour meter and RPM indicator.

SAFETY SYSTEM OF ENGINE :-The Engine shall trip for the following conditions with visual alarm device 1. Low lubricating oil pressure 2. High Water temperature 3. Vee-belt failure and over speed 4. The visual indicator should be provide for Low battery indication. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load 2. ALTERNATOR : Alternator capacity of 320 KVA/ 200 KW,AC 3 phase, 50HZ, 415/420V, 0.8P.F.4 wire self excited, self regulated designed to run at 1500 RPM under NTP conditions confirming to BS 5000/ IS 13364 (part-II) 1992 to be coupled directly to the Diesel engine and test certificate (Make: Kirloskar/ Crompton/ Greaves/ Equivlent.) 3.ACOUSTIC ENCLOSURE:- Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet.The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machine to maintain dimensional accuracy of hole within 0.1mm Powder coating done after seven – tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 Kg/m density mineral wool of 100mm thickness as Acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt distance shall be less than 75 DBA average or as per CPCB norms. Surface treatment – Painting: The enclosure surface shall be suitably treated for degreasing de-rusting and posphating. The canopies are passed through seven – tank

The canopies are passed through seven – tank treatment thoroughly. Additional features of canopies: Canopy fabricated on CNC machines with dimensional accuracy of 0.1 mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG sets if any World class Cooling package: Canopies shall have cooling package for which it can also perform at 45 degree C/ambient temperature.No grouting required on the ground, only a level surface capable of with standing the DG weight.Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set. 1150.00 30250.00 The Gen set frame shall also be provided with hooks for unloading Temperature rise inside the canopy: Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 5-7 deg centigrade. 4. FUEL TANK : 350 liters. Removable fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connection and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance. 5. BASE FRAME : The base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall be have provision for mounting of acoustic enclosure on it. The supply of generator set includes loading. Unloading and transportation charges.

160KVA STANDBY GENSET

Supply, Erection, Testing, Commissioning and Handing over of 1 No 160 KVA Diesel Generator set of 0.8P.f, Three Phase, 415/420Volts, 50c/s, 1500RPM as detailed below with AMF panel. 1.ENGINE: Water cooled Diesel engine suitable for generator application with a shaft Output of 385 BHP at 1500 RPM under NTP Condition as per BSS 5514/IS 10000. The engine shall comprise the following standard scope of supply: (Make Kirloskar/ Cummins/ Ashok Leyland/ Greaves/Equivalent) 1. Dry type Air cleaner 2. Expansion bellow 3. Radiator, Radiator fan and mounting 4. Air to air charge cooler 5. Exhaust Gas turbo charger 6. Lube oil cooler and Lube oil filter 7. Fuel filter(pre and micro 8. In-line Mono-block fuel injection pump with governor and fuel feed pump 9. Electronic governor 10. 24V Battery charging alternator 11. 24V Volt electric starter motor 12. Engine test Certificate 13. Residential Mufler 14. Fly wheel with starter ring.

ENGINE INSTRUMENTPANEL MOUNTED. Engine control panel consisting of ON/OFF/START Key Lube oil pressure guage , oil temperature gauge, high water temperature guage and electronic hour meter and RPM indicator.SAFETY SYSTEM OF ENGINE :-The Engine shall trip for the following conditions with visual alarm device 1. Low lubricating oil pressure 2. High Water temperature 3. Vee-belt failure and over speed 4. The visual indicator should be provide for Low battery indication. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load 2. ALTERNATOR : Alternator capacity of 160 KVA/ 128 KW,AC 3 phase, 50HZ, 415/420V, 0.8P.F.4 wire self excited, self regulated designed to run at 1500 RPM under NTP conditions confirming to BS 5000/ IS 13364 (part-II) 1992 to be coupled directly to the Diesel engine and test certificate (Make: Kirloskar/ Crompton/ Greaves/ Equivlent.) 3.ACOUSTIC ENCLOSURE:- Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet.The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machine to maintain dimensional accuracy of hole within 0.1mm Powder coating done after seven – tank surface preparation process

of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 Kg/m density mineral wool of 100mm thickness as Acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt distance shall be less than 75 DBA average or as per CPCB norms. Surface treatment – Painting: The enclosure surface shall be suitably treated for degreasing de-rusting and posphating. The canopies are passed through seven – tank The canopies are passed through seven – tank treatment thoroughly. Additional features of canopies: Canopy fabricated on CNC machines with dimensional accuracy of 0.1 mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG sets if any World class Cooling package: Canopies shall have cooling package for which it can also perform at 45 degree C/ambient temperature.No grouting required on the ground, only a level surface capable of with standing the DG weight.Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set. 1150.00 30250.00 The Gen set frame shall also be provided with hooks for unloading Temperature rise inside the canopy: Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 5-7 deg centigrade.

supply and installation of Exhaust pipe with silencer (SOR M 2085)

Filling up Diesel for first running and testing

Supply and Run of 12 core 2.5 sqmm armoured copper control cable FRLS in suitable PVC rigid pipe on wall/Ground/ ceiling with connection (For AMF to 250KVA Genset) (Data 65)

UPS Supply and installation of 40 KVA Online UPS suitable for Three Phase input, three phase output with IGBT rectifier and isolation Transformer, to support two hours battery backup using 12V 120AH sealed maintenance free battery with MS Battery rack and interlink cables. (Quotation enclosed)

BOOM BARRIER Supply and installation of automatic grade boom barrier of 50HZ frequency, 220v, 120W power single phase working temperature 35 degree C - 75 degree C, motor roatational speed 1400RPM complete compiling with standard specification (Quotation enclosed)

TURNSTILE (Quotation enclosed) Supply & Fixing for Bi-directional single passage Turnstile Gate 550 mm with following specification, Operating Modes = Bi-directional single passage Authentication Mode = Card Pass Rate = 40 Persons/min Passage Width = 550 mm Drive = Electro Mechanical Drive DC Interface = Lock Control Power Supply = 220 VAC , 50/60 Hz MCBF = 5,000,000 Cycles Operating Temperature = -10 to 60 deg C Working Humidity = 0% to 95% (No condensing) IP Rating = IP55 Housing Material = SUS304 Stainless Steel Material Barrier Arms = Stainless Steel 316 Housing Dimensions = 980 x 480 x 280 mm Barrier Length = 550 mm Weight = 44 kg

SOLAR PANEL

Providing 10 KW On-grid rooftop Solar photo-voltaic systems including the following items: a) SOLAR PV MODULE :Solar module with high module output, well equiped with efficient crystalline cells and characterised by high yeilds, long service life, certified in accordnce with ISO 9001 international high quality standard. Modules must qualify to IEC 1730 Part I and II for safety qualification testing or Equivalent IS & IEC 61701/IS 61701. Each PV module must have RF itentification tag (RFID), PV module type : Bifacial mono crystalline PV module capacity 10 kW, Make : Waree/Renewsys/Vikram Solar or Equivalent. b) MOUNTING MOUNTING STRUCTURE: Modules should be mounted on fixed metallic structures of adequate strength and appropriate design which can withstand load of modules and high wind velocities upto 160 km/hour. The support structure used in the power plant should be hot dip galvanied iron (G.I) having 120 microns coating. Each panel frame structure should be fabricated as to be on the roof on its legs. The legs of the structure should be fixed and grouted in the PCC foundation column made with 1:2:4 cement concrete. The foundation should support SPV modules at a given orientation, absorbs and transfer the mechanical loads to the ground properly and should withstand maximum wind Speed of 160Km/hr. c) DC CABLES: Supply of 4 sqmm DC copper cable or XLPE insulated and PVC unsheathed single or multicore cable with minimum 4 sqmm in suitable PVC rigid pipe on wall from PV array to DCDB

d) AC CABLES: Supply and run 4 core 25 sq.mm PVC or XLPE insulated multi strand copper cable PVC and PVC unsheathed single or multi core flexible cable with voltage rating 1100 volts UV stabilized copper cable in suitable PVC rigid Pipe from ACDB to Electrical bus bar. e) ARRAY JUNCTION BOX: The junction box should be dust proof, Vermin and water proof and made of FRP/ Thermo plastic, the terminals should be connected to copper bus bar arrangement of proper sizes for both incoming and outgoing cables. Suitable makings should be provided on the bus bar for identification and cable termination points for identification. f) DCDB: A DC distribution box should be mounted close to the solar grid inverter. The DC distribution box should be of the thermo plastic IP 65 DIN –rail mounting type and should comprise the following components and cable terminations – incoming positive and negative DC cables from the AJB Box DC isolator, 2 Pole (the cables from the AJB Box will be connected to this isolator on the incoming side )- DC surge protection device (SPD), class-2 as per IEC- 60364-5-53; -g) ACDB: An AC DB box should be provided in between PCU and loads. It should have MCB of suitable rating for connection and disconnection of PCU from load and should be mounted close to the Grid Tie Inverter with thermo plastic IP65 protection for cable termination points for identification.h) CABLE: Supply and run of 16sq.mm single core copper insulated cable with necessary clamp / Supports on wall/floor/ground for earth connection

i)EARTHING: PV module structure components should be electrically interconnected and should be grounded. Earthing should be done in accordance with IS 3043-1986, provided that earthing conductors should have a minimum size of 6.0 mm2 copper, 10 mm2 aluminium or 70 mm2 hot dip galvanized steel. Unprotected aluminium or copper-clad aluminium conductors should not be used for final underground connections to earth electrodes. A minimum of two separate

dedicated and interconnected earth electrodes must be used for the earthing of the solar PV system support structure with a total earth resistance not exceeding 5 Ohm. The earth electrodes should have a precast concrete enclosure with a removable lid for inspection and maintenance. The entire earthing system should comprise non-corrosive components. GI Earthing System comprising of 50mm dia and 1 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp

j) LIGHTNING ARRESTER: Supply of Early Streamer Emission Air Terminal (ESEAT). Model: HAVING corrosion resistant stainless chrome body made up of AISI 316 grade of height 0.50 metres capable of working in hazardous atmosphere. hazardous atmosphere. The Air terminal is non-radioactive and requires no special licensing. The unit is fully autonomous (no battery, no external power supply is required), collects energy from the ambient electric field.The ESEAT model hasbeen tested in a high voltage laboratory in accordance with NFC 17 102 in order to measure the average gain in triggering. The average gain in triggering time (∆Ts) obtained during the lab test for the offered model is 60 µs. The ESEAT works on negative as wellas positively polarized discharges. ESEAT has been tested for such discharges in Central Power Research Institute (CPRI). A dedicated tester is avilable to test the healthiness of the ESEAT on request (Page No. 37, Point No. 3 of Clause 8.6 of the Revised NFC 17-102 version 2011 ). ESEAT Model : L - Radius of protection : 86 Metres Level of protection considered for the Project-II level

Supply and fixing of 100A four pole MCCB in suitable sheet steel enclosure with earth connection (DATA - 66)

LED DIGITAL DISPLAY BOARD Supply and Fixing of outdoor LED Digital Display with module size of 3000x2000mm with pixel pitch (mm) of 3.91 with unit weight of module with cabinet less than 25 Kg/sq.m, module resolution 64x128, physical pixel density not less than 65000 pixels/sq.m having the flatness of cabinet +/-0.3mm, minimum brightness of 5000 (after calibration), colour temperature of 3500 to 9000 having visual viewing angle of 160 (horizontal) and 136 (vertical), contrast ratio of 6000, maximum power consumption of 650W per aluminium cabinet (2x4 modules) or 650 W/Sq.m, power supply 100 to 240 V with frame rate of 50/60 Hz and refresh rate of 3840 Hz. Lifetime of 100000 hrs to half brightness with waterproof IP rating Front/Rear of IP65 with all the necessary fixing arrangement on the outside wall. (Quotation Enclosed).

BATTERY CAR (BUGGY) Supply of DR2E - Yamaha Battery Operated Golf Car - 6 Seater (4 All Forward & 2 Rear Facing) -CRUISE - AC MOTOR & 6 member of Seating Capacity includes with Suntop,Windshield,USB por,Hydrolink Watering System, Charger Power Cable,Rear Facing Seat Kit,Head Light, Tail Light, Horn, Side View Mirror Kit - 1, Battery: Trojan Battery 8 Volt - 6 Nos (170 AH) including transportation charges (including extra additional 1set of backup batteries) (Quotation Enclosed).

PUBLIC ADDRESS SYSTEM

Supply, installation, testing and commissioning of 240 Watts power Amplifier unit with Mic. Inputs, control wires,power cables, etc., as per standard methods and as directed by the department officers.(BOSCH/Equivalent)

Supply and runs of 2 core 1.5 sqmm multi strand shielded Copper Cable for PA wiring between PA console and PA speaker provided in respective Zone in existing 20/25mm dia PVC pipe as per standard methods and as directed by the department officers.

Supply and laying of 25mm dia PVC conduit Pipe in wall or Ceiling using suitable size GI mounting bracket, anchor Fateners,nylon strap etc., as per standard methods and as directed by the department officers.

Supply and laying of Wall mounted volume control complete with back box, necessary fixing accessories.

Supply and laying of Table mounted type with ghoose neck mike, neccessory fixing & connecting accessories.

Supply and laying of suitable floor Mountable powder coted Rack with 6x5A Power Manager, 2 Horizontal Cable Manager, 4 position fan, min 1 nos of shelf, Front Glass door with Lock & key for PA system

Supply and laying of sizes 4 core 16 sq.mm. armoured aluminium cable of Armoured Aluminium Cables for electrical motor, control panel, pressure switch, jockey motor etc., The rate inclusive of all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary , etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.SOR Item.No 326 b,Pag.no.80

Sub total

GRM CONSTRUCTIONS

ABIRAMI ENGINEERING CONSTRUCTION AND CO