Loading…
Loading…
Tender Value
₹1.4 Cr
EMD Value
₹2.2 L
Closing Date
14 Jul 2025, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
CPH
14 conditions · 2 needing a document upload
Financial Eligibility criteria:- The tenderer must have minimum average annual contractual turn over of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Technical eligibility criteria:-(a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited:(i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or(ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender.(b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07(seven) years, ending last day of month previous to the one in which tender is invited:(i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or(iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity.(b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing.However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract.In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract...(For detailed standard technical criteria go through GCC 2022)
Defination of Similar Work :- Supply, installation and commissioning of High mast lighting/tower lighting system of different height at any places.
2 conditions
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderer must have capacity to complete this work in stipulated period mentioned inNIT and tenderer must submit available Bid Capacity as per ANNEXURE -VII of tender document.
Provision of High Mast lighting system in Colony of CLW,Chittaranjan
EL-CON-508
EL-CON-508
Open
Works - General
3 Months
Paschim Bardhaman, West Bengal
₹0
₹2.2 L
14 Jul 2025
23 Jun 2025
4 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Supply, installation, connection and commissioning of High Mast Light Tower with all accessories : Supply of 20 M High Mast shaft in two section suitable for 50 m/sec wind speed along with head frame, luminaires carriage suitable for 08 luminaires in symmetrical arrangement and supply of raising- lowering (manually and motor operated )system comprising of double drum winch, 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor,manual handle, junction box, etc. including supply of 1 set of foundation bolts made of special steel along with nuts,washers, anchor plate and common template.Supply of LED type single dome aviation obstruction light Supply of 8 Nos. Targeted Beam IP66 Epoxy powder coated pressure die-cast aluminium housing 250W LED targeted flood light with supply of 30 meter 4 core 4 Sq mm PVC insulated and sheathed stranded copper conductor, 1.1 KV grade cable as per IS:694, including making of M20 grade cement concrete foundation for the installation of High Mast Tower and grouting of base in the foundation. Note:- Firm has to provide necessary outdoor feeder pillar with standard accessories, Proper earthing for High mast and Feeder panel ,etc. The scope of work includes the installation of High Mast Light Tower at the purchaser's premises, as per the directions provided. The contractor shall supply all necessary accessories required for the complete installation. | Numbers 15.00 | 450735.04 | 67,61,025.6 | — |
| 2 | Supply, installation, connection and commissioning of High Mast Light Tower with all accessories : Supply of 30 M High Mast shaft in two section suitable for 50 m/sec wind speed along with head frame, luminaires carriage suitable for 08 luminaires in symmetrical arrangement and supply of raising- lowering (manually and motor operated )system comprising of double drum winch, 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor,manual handle, junction box, etc. including supply of 1 set of foundation bolts made of special steel along with nuts,washers, anchor plate and common template.Supply of LED type single dome aviation obstruction light Supply of 8 Nos. Targeted Beam IP66 Epoxy powder coated pressure die-cast aluminium housing 400W LED targeted flood light with supply of 40 meter 4 core 4 Sq mm PVC insulated and sheathed stranded copper conductor, 1.1 KV grade cable as per IS:694 , including making of M20 grade cement concrete foundation for the installation of High Mast Tower and grouting of base in the foundation. Note:- Firm has to provide necessary outdoor feeder pillar with standard accessories, proper earthing for High mast and feeder pillar ,etc. The scope of work includes the installation of High Mast Light Tower at the purchaser's premises, as per the directions provided. The contractor shall supply all necessary accessories required for the complete installation. | Numbers 5.00 | 748800.00 | 37,44,000 | — |
| 3 | Supply and Laying of 4 Core 25 Sq. mm. cable XLPE insulated and PVC sheathed stranded Aluminum conductor steel strip armoured cable 1.1 KV grade cable as per IS: 7098 (Pt.I). | Metre 7000.00 | 164.18 | 11,49,260 | — |
| 4 | Digging and excavation of soil (size 300mm width and 750 mm depth) and formation of kachcha cable trench after dressing, including supply and laying of bricks, brick walling, brick covering, and sand filling at the bottom to cover the cable. | Metre 7000.00 | 333.38 | 23,33,660 | — |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .