SPECIAL REPAIR TO OMQs AND CERTAIN BR AND EM SANCTIONED WORKS AT AFS KANHERI HILLS UNDER GE AF THANE

Amount

M&L for Pre-cast cement concrete block masonry 1:3:6 Type C-1 (using 20mm graded aggregate)with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete complete all as specified and directed by Engr in Charge

M&L for RCC 1:2:4 using 20mm graded aggregate nominal mix as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Material & labour for providing reinforced cement concrete (1:1½: 3) type B0 (using 12.5mm graded stone aggregate) mixed with integral water proofing liquid admixture CONPLAST X421IC (Fosroc) or equivalent as per manufactures instructions as in columns, pillars,lintel, slab supported walls roof, landings, balconises, canopies, deck slabs, Chajjas shelves, Fins, fascias, louvres, parapets, and railings, newels, balustrade, and the like etc including necessary form work and scaffoldings up to 2 story of building complete all as specified & as directed.

Supply only integral water proofing compound.

Cutting holes in brick walls exc half bricks but nexc one brick built in cement mortar or cement lime mortar for inserting holdfasts and making good dismantled portion in cm (1:3) or cement concrete (1:2:4) type B1 as required

M&L black granite (of any type) 20 mm thick work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed by Engr in Charge.

M&L for 25 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed by Engr-in-Charge.

M&L for formwork to edges of concrete flats, and similar work;

M&L for Plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads, Exc 13 Sq cm & n Exc 25 Sq cm.

M&L for Plain fillets, square, rectangular or triangular in section, clean sawn, secured with mills or brads, not Exc 3 Sq cm.

Chamfers, splays, grooves, rebates, rounded angles, rounded nosings, tongued and grooved edges (each tongue and each groove measured) etc., exc 3mm but n. exc 75m girth softwood

S&F IInd class hard wood plain, solid, straight chowkat and frame wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints all as specified.

S&F for 35mm thick IInd class hard wood glazed and skelton shutters divided into squares with plain chamfered or reounded miltred and related sash bars number to received glass gauze etc edges of framing plain chamfered or reounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I section 8 clause 8.20(a) supplied and fitted to chawkats.

S&F for 35mm thick IInd class HW rail and style plain framed panelled factory made shutter (Two panel) with lock rail and panel of 9mm BWP,commercial ply or 12mm veneered particle beard with commercial veneering on both faces. The size of rail and stile as per IS :1003 (Part-I) kiln and chemically pressure treated.

Taking down chowkats or frames with shutters (without taking off shutters form frame) n. exc 1.5 sqm each

Taking down chowkats or frames with shutters (without taking off shutters form frame) . exc 1.5 sqm & n.exc 4 sqm each

Repairs to shutters of any description n. exc 1 sqm each easing & adjusting without taking down

Taking down shutters of size exc 1 sq. m and n exc 2 sq. m each and refixing in the same opening including necessary adjustment after laying of floor tiles complete all as specified and directed

Repairs to shutters of any description easing & adjusting without taking down area exc 1 sqm but n. exc 2 sqm

S&F solid PVC solid door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling and fixing in opening with stainless steel screws of required size complete all as specified and directed.

S&f factory Made Solid PVC Moulded Door Shutter,with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing. Including 3 Nos of stainless steel 100 mm size hinges, 2 Nos of aluminium 100 mm size handles, 2 Nos of toer bolt 100 mm size all as directed

S&F aluminium anodized barrel tower bolt extruded section and fixed 200mm long all as directed

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 250mm length and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified.

S&F butt hinges, medium weight, cold rolled mild steel, 100mm all as directed.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished as in cabinets all as specified and directed.

S&F mild steel 300mm ordinary rat tail rod pettern springs including roller and roller plate complete

S&F for 75 mm brass handles, cast type , polished type complete all as specified and directed by Engr-in-Charge

S&F for 150 mm brass handles, cast type , polished type complete all as specified and directed by Engr-in-Charge

S&F in repairs Brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges complete all as specified and directed.

S&F Floor door stopper 150mm length of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe 410-0 or Fe 310-0 (Brackets over 10kg each to be measured under `Structural Steel') complete all as specified and directed.

M&L for 25 x 3mm FI holdfasts for fixing door frame all as directed.

M&L for TMT bar 10mm dia and over cut to length bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with MS wire not less than 0.9 mm dia or securing with chips quality conforming IS

Ditto as item no-35.00 above but but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M & L for pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Opening out cracks, V section of wall/roof removing the loose material. Filling with cement mortar 1:3 all as specified.

M&L for 0.9 mm thick decorative laminate type 1 of surface finished colour and pattern as approved, fixed with approved adhehive as per manufacturer's instruction complete all as specified and directed by Engr-in-Charge

M&L for Block board 18 to 19mm thick , interior grade commertial type fixed with screws to timber frame work/wall for making cubboard door shutters complete all as specified and directed by Engr-in-Charge

M&L for Block board 12 mm thick , interior grade commertial type fixed with screws to timber frame work/wall for shelf in cubboard complete all as specified and directed by Engr-in-Charge

M&L for 75 mm thick PCC type C-2, 1:3:6 using 40mm graded stone aggregate as in finishing surfaces of concrete, finish topping even and fair (without using extra cement), complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and as directed

Material and labour for brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and as directed

Material and labour for Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in vertical position as dado/skirting. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-In-Charge

Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to stone and rubbish of the premises.

Material and labour for rendering 10mm thck in CM 1:4 as backing coat to receive tiles in vertical position as dado/skirting complete all as specified and directed by Engr-In-Charge

Material and labour for 20mm thick screed bed in CM 1:4 for laying floor finishes complete all as specified and directed by Engr-In-Charge

Taking down cement plaster of any description on brick walls including raking out joints, hacking for key, scrubbing down with water complete all as specified & as directed.

M&L for 4 mm thick sheet glass n exc 0.5 sq.m in each pane fixing cabinet shutters with necessary screw/fittings complete all as specified and directed.

S&F sheet glass ordinary quality 3.00mm thick and glazing with oil putty or aluminium/rubber beading in squares n.exc 0.5 sqm in each pane

S&F figured glass, pin-headed type 3.00 mm thick and glazing with oil putty or aluminium/rubber beading in squares n.exc 0.5 sqm in each pane.

Hacking out old broken glass (any thickness, size, quality or description) from alluminium/wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads exc 1.5 sqm

M&L for preparation of new wood surfaces of any description over 10cm width of girth applying two coats of synthetic enamel paint over coat of pink primer etc complete all as spcified.

M&L preparation of new or previously untreated surface of steel and applying two coat synthetic enamel painting over a coat of priming red oxide zinc chrome complete all as specified and directed.

M&L for 15mm bore medium grade G.I tubing with all fittings & fixed complete to walls & ceilings or laid in floors all as specified and directed by Engr in Charge.

M&L for 20mm bore medium grade G.I tubing with all fittings & fixed complete to walls & ceilings or laid in floors all as specified and directed by Engr in Charge.

Taking down steel tubing & connections incl cleaning for refixing or removal to store for 15mm bore of pipe all as specified and directed by Engr in Charge.

Taking down steel tubing & connections incl cleaning for refixing or removal to store for 20mm bore of pipe all as specified and directed by Engr in Charge.

Refixing old GI steel tubing with and including necessary fitting& connections in new or old position (walls, ceiling, floors etc) 15 mm bore of pipe all as specified and directed by Engr in Charge.

Refixing old GI steel tubing with and including necessary fitting& connections in new or old position (walls, ceiling, floors etc) 20 mm bore of pipe all as specified and directed by Engr in Charge.

Cutting existing 20mm steel tubing for alterations or additions in any position without taking down (Each cut measured)

Dismantling water tank capacity exc 500 and n exc 1000 ltr and removing to store all as directed

S&F1000 Ltr Rotational moulded polyethene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed by Engr in Charge.

S&F as in repair15mm dia pillar tap chromium plated cast copper alloy with capstan head, fancy type screwed down high pressure with or with out letters Hot or cold with long screwed for iron pipe all as specified.

S & F in repairs brass CP mixer for mixing hot & cold water screwed down for iron pipe15mm dia all as specified and directed by Engr in Charge.

S&F in repairs quarter turn stop valves CP Brass fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe 15mm dia all as specified and directed by Engr in Charge.

S&F in repair 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr in Charge.

S&F in repair 20mm Ball valves, high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (Minimum weight 20mm-210gms complete complete all as specified and directed by Engr in Charge.

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) all as directed

S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms)

S&F urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)

S & F in repairs PVC connections 15mm dia with brass nut on both ends and washers 450mm long all as specified and directed by Engr in Charge.

Supply and fix 100mm bore cast iron (Sand cast pipes) soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to wall with MS clamp complete all as specified and as directed.

All as per item No 73.00 above but 75 mm bore.

Fixing only cast iron soil waste and vent pipes of 100mm bore in any lenth with or without ears with cement joints fixed to walls including taking down old cast iron pipe complete all as specified and as directed (Serviceable pipe obtained from relevent item of Sch A shall be reused).

M&L for 110mm bore PVC(SWR) pipe single socketed in any length with rubber ring joint fixed to wall fixed in repairs

M&L for 75mm bore PVC(SWR) pipe single socketed in any length with rubber ring joint fixed to wall fixed in repairs

S&F PVC (SWR)110mm bore bend fixed in repairs

S&F in repairs PVC (SWR) junction single T equal or unequal 110mm bore

S&F in repairs PVC (SWR) junction single T equal or unequal 75mm bore

S&F 75mm bore PVC (SWR) vent cowl.

M&L PVC (SWR) vent cowl 110mm bore fixed in repairs

M&L PVC (SWR) 75mm bore floor trap, plain with grating including jointing with solvent cement fixed in repairs

Demolition of brickwork or stone boulders masonry built in CM incl all quins, arches, pillers etc

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Demolition of concrete of any description and in any position not otherwise specifically provided all as specified and directed by Engr in Charge

Demolition of cement Concrete in Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work

Dismantling cast iron drain pipes of any description complete all as specified and as directed.

Dismantling of asbestos cement (corrugated, semicorrugated,etc sheets in roof coverings all as directed

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;

M&L for 0.9 mm thick decorative laminate type 1 of surface finished white colour and plain, fixed with approved adhehive as per manufacturer's instruction complete all as specified and directed by Engr-in-Charge

M&L for medium density fibre board 12mm exterior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work.

M&L for medium density fibre board 18/19mm exterior grade, prelaminated with both side white laminations , fixed with screws to timber frame work.

Material and labour for glazed ceramic colour tiles 300x200 x7mm thick in skirting/dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles over and including 10mm thick rendering in CM(1:4) complete all as specified and as directed.

Material and labour for non-skid coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exceeding 0.06 Sqm but not exce 0.11 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed or bedding layer in CM(1:6) complete all as specified and as directed.

M & L for rendering 20 mm thick in cement mortar 1:4 (15 mm thick backing coat and 5mm thick finishing coat) on fair faces of brick work or concrete surfaces including finished even and smooth without using extra cement with using water proofing compound (water proofing compound shall be measured and paid seperately)

M&L for rendering 5mm thick in cm 1:3 on fair faces of concrete as in soffit ceiling of slab, chajjas finished even & smooth without using extra cement all as specified.

M&L for rendering 15mm thick in cm 1:6 on fair faces of brick work or concrete surfaces of wall and finishing the surface even and smooth without using extra cement complete all as specified.

M&L for rendering 5mm thick in CM 1:4 on fair faces of concrete as in ceiling of slab finished even and smooth without using extra cement all as specified.

M&L for preparing new plastered surfaces and applying two coat of OBD over a coat of alkali resistant priming paint complete all as specified.

M&L for Preparing new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L preparation of old painted steel surface & applying a coat of synthetic enamel paint all as specified.

S&F in repairs bib tap 15mm bore chromium plated cast copper alloy with crutch or butter fly handle but fancy type screwed down screwed for iron pipe complete all as specified and directed.

S&F in repairs brass cromium plated shower rose with swivel joint 125 mm size all as specified and directed by Engr in Charge.

S&F in repairs wash down water closet (EWC) (pedestal pattern) complete (excluding flushing cistern or flush pipe) all as specified and directed by Engr in Charge.

M&L for vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including connections to flushing pipe and outgoing pipes fixed in repairs

S&F in repair low level flushing cistern plastic valve less syphonic action type white with inlet ball valve float and ball handle & capacity 10 ltr ISI marked including 32mm PVC flush pipe complete all as specified and directed.

S&F in repairs plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel hinge chromium plated all as specified and directed by Engr in Charge.

S&F in repair vitreous china wash hand basin white flat back size 550 X 400 mm excluding taps waste chain and plug and porcelain stopper but including brackets complete all as specified and directed. .

Taking down/dismantling loose/damage concrete including plaster of any description and in any position from RCC structures like chajja, fins, louvers, parapet, column, beam, and of lintel by hammering with wooden mallets carefully chipping off the old concrete surface including cutting of rusted reinforcement if so required and disposal of old debris to outside the premises complete all as specified and as directed.

S&F extruded aluninum alloy handles, fabricated type anodized 150mm long fixed all as directed

M&L for Stainless steel trolley made with perforated sheet of not less than 1.52 mm thick and SS edging wire and slided over SS telescopic renners which is fixed wall/stone with suitable screws of desired shape and size as directed by engr-in-charge

S&F heavy duty SS Zink plated Teliscipic runners for SS trolleys having fully extended length min 500mm and 45.4 mm wide, loading capacity 45 kg/pair including concealed screws and bolts fixed to the wall or stone as directed by engr-in-charge

Drilling holes of 25 mm dia through cuddappah stone and RCC slab together of thickness 100-250mm as per directed by Engr-in-charge

Cleaning the existing surface of concrete and reinforcements as obtained after execution of item No. 1, here in before by wire brush including scrapping & cleaning with emery paper and washing down with water as required and applying “Solvent free epoxy concrete bonding agent” as per manufacturer’s instructions on old concrete surfaces for bonding with new concrete complete all as specified & as directed.

Supply only. Solvant free Epoxy concrete bonding agent. Make : Nitobond EP of FOSROC/Carbodur of SIKA/ or equivalent in PEDILITE

M&L for Preparing new plastered surfaces, wall over a coat of weather coat primer and applying two coats of acrylic paint exterior grade all as specified.

M&L complete preparation of existing treatment on wall including removal of grass and applying one coats of acrylic weather proof exterior paint all as specified and directed by Engr-in-Charge.

Cleaning the existing surface of concrete and reinforcements as obtained after execution of item No. 1, here in before by wire brush including scrapping & cleaning with emery paper and washing down with water as required and applying “Solvent free epoxy concrete bonding agent” as per manufacturer’s instructions on old concrete surfaces for bonding with new concrete complete all as specified & as directed.

Supply only. Solvant free Epoxy concrete bonding agent. Make : Nitobond EP of FOSROC/Carbodur of SIKA/ or equivalent in PEDILITE

S&F Stainless steel soft close hydraulic action hinge with capacity to take load of 12 to 20 mm thick board all as per directed and specified by Engr-in-charge

M&L for preparing new plastered surfaces of external wall of wardrobes and applying two coats of high performance polymer modified cementious coating with Dr.Fixit Fastflex or equivalant product as per manufacturers instruction complete all as specified and directed by Engr In Charge.

M&L for preparing new plastered surfaces of wall and applying two coats of acrylic weather paint exterior grade over a coat of weather coat primer complete all as specified and directed by Engr In Charge.

S&F in repair aluminum anodized windows/doors with necessary accessories/fitting after taking down and refixing after replacement of broken aluminium section, rectification of roller, wiremesh, window panes etc Note : All items used in rectification shall be paid separately under Item No. 128 to 131

(a) Supply only aluminium anodised powder coated frame for doors/windows, ventilators and aluminium section for windows as directed

(b) Supply only rollers for sliding windows including fixing to aluminium windows section after taking down old unserviceable rollers

(c) Supply only stainless steel wire cloth, 0.36mm nominal dia of wire and average width of sperture 1.40mm and fixed with stainless steel wire staples

(d) Supply only sheet glass 4.00mm thick, ordinary quality and glazing n.exc 0.50Sqm in each pane

Taking down Point Wiring (Light, Fan, Socket or Power) of any type on Batten/ PVC Casing & Caping or in Conduit with Fittings and Fixture such as Switches, Ceiling Roses, Pendants, Regulators, Sockets, Light Fitting, etc. including necessary Chase cuttings on Brick Walls, Ceilings, Floors, etc. to remove Conduit, etc., complete all as specified and as directed.

Taking down/out unserviceable Wires from the existing Sub-main Wiring of any type and any description, complete all as specified and as directed.

Taking down the existing unserviceable Main Switch/ Cut out/ DBs of any type/ capacity and any description as existing at Site including Making Good the Disturbed Surfaces of Walls, Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Conductor drawn through and including Rigid Non-metallic PVC Conduit 25mm in size, medium grade, ISI marked including necessary Conduit Accessories, Partly Surface/ Partly Concealed as ordered, mounted on 1.6mm thick Sunk Mild Steel Pressed Terminal Box of suitable size duly painted with Red Oxide Metal Primer with 3.0mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, Fan Regulators, etc. and Earth Continuity connected to Common Earth dolly for ONE LIGHT/FAN POINT/Bell Point CONTROLLED BY ONE 1-WAY SWITCH 6 AMP including grouting Conduit on Brick Walls, etc. and Making Good disturbed Surfaces of Brick Walls, Ceilings, Floors, etc. in Cement Mortar 1:3 and necessary Surface Treatments so as to match with the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Conductor drawn through and including Rigid Non-metallic PVC Conduit 25mm in size, medium grade, ISI marked including necessary Conduit Accessories, Partly Surface/ Partly Concealed as ordered, mounted on 1.6mm thick Sunk Mild Steel Pressed Terminal Box of suitable size duly painted with Red Oxide Metal Primer with 3.0mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, Fan Regulators, etc. and Earth Continuity connected to Common Earth dolly for ONE LIGHT POINT CONTROLLED BY ONE 2-WAY SWITCH 6 AMP including grouting Conduit on Brick Walls, etc. and Making Good disturbed Surfaces of Brick Walls, Ceilings, Floors, etc. in Cement Mortar 1:3 and necessary Surface Treatments so as to match with the Existing Finishes, complete all as specified and as directed.

All as per item No. 136.00here-in-before but for one five pins 5 Amps switch socket outlet point on same board complete all as specified and directed.

All as per item No.136.00 here-in-before but for ONE 3 PIN SOCKET OUTLET 6 AMP ON THE INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable drawn through/in EXISTING CONCEALED CONDUIT/ PVC CASING & CAPING with Continuous Earth Wire 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable (Green Colour) connected to Main Earth Wire and Earth Dolly providing 3.0mm thick Hylam Sheet Top Cover ISI mark on existing Terminal Box, suitable for mounting Switches, Sockets, Fan Regulators, etc. for ONE 3 PIN SOCKET 16 AMP ON INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable drawn through/in EXISTING CONCEALED CONDUIT/ PVC CASING & CAPING with Continuous Earth Wire 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable (Green Colour) connected to Main Earth Wire and Earth Dolly providing 3.0mm thick Hylam Sheet Top Cover ISI mark on existing Terminal Box, suitable for mounting Switches, Sockets, Fan Regulators, etc. for ONE 3 PIN SOCKET 16 AMP ON INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 4.0 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable and 1-Run of 4.0 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty along with the Wiring drawn in EXISTING CONDUIT/PVC CASING & CAPING, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 6.0 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable and 1-Run of 6.0 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty along with the Wiring drawn in EXISTING CONDUIT/PVC CASING & CAPING, complete all as specified and as directed.

S&F PVC Conduit, ISI marked, heavy duty of size 25mm with all Fittings/ Accessories including taking down old unserviceable PVC Conduit, complete all as per specified and as directed.

S&F Switch Piano 6 Amp, Flush type, Single Pole, 1-way, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Flush type, Push Button, suitable for Call Bell, complete all as specified and as directed.

S&F Switch Piano 16 Amp, Flush type, Single Pole, 1-way, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, Piano, Flush type, 2-in-1, multi-purpose, 3 Pin, complete all as specified and as directed.

S&F Socket Outlet 6 Amp & 16 Amp, Piano, Flush type, 2-in-1, multi-purpose, 5 Pin, complete all as specified and as directed.

S&F Ceiling Rose, 3 Terminals, PVC Polycarbonate, Isolated body complete all as specified and as directed.

S&F Fan Regulator in 5 Step type, Single Pole, 230 Volt, Electronic type, complete all as specified and as directed.

S&F Call Bell Electric Single Pole, 230 Volt, AC supply, Ding Dong type complete all as specified and as directed.

&F Decorative Wall Light Fixture made up of Polycarbonate with LED Lamp 0.5 Watt (Red/Blue/Green) (B-22 Base) Light fixed on the Wall/ Ceiling and connecting up with and including Copper Conductor Cable of size 23/0.0076 Sqmm 3 Core PVC Copper Flexible Conductor and necessary Earthing Connection from to Light Fitting complete all as specified and as directed.

Decorative Ultra Slim Linear LED Lighting Fixture with Extruded Polycarbonate, Environmental Friendly, Energy Efficient 5 Watt LED 6000K and connecting up with and including Copper Conductor Cable of size 23/0.076 multi-stranded, 3 Core from Ceiling Rose to Light Fitting, complete all as specified and as directed.

S&F LED Light Fitting 6.0 Watt 6000K, Surface mounted Square/Round shaped (as available) LED downlighter with durable Housing with Aluminum Heat Sink with Diffuser to give Glare Free Light with Removable Driver, complete all as specfied and as directed.

Decorative Ultra Slim Linear LED Lighting Fixture with Extruded Polycarbonate, Environmental Friendly, Energy Efficient 10 Watt LED 6000K and connecting up with and including Copper Conductor Cable of size 23/0.076 multi-stranded, 3 Core from Ceiling Rose to Light Fitting, complete all as specified and as directed.

Decorative Ultra Slim Linear LED Lighting Fixture with Extruded Polycarbonate, Environmental Friendly, Energy Efficient 18 Watt LED 6000K and connecting up with and including Copper Conductor Cable of size 23/0.076 multi-stranded, 3 Core from Ceiling Rose to Light Fitting, complete all as specified and as directed.

S&F MCB Single Pole, 6 to 32 Amp, 240 Volt, AC, 'B' Series for fixing on MCB DB’s, 10 kA, 50 Hz and connecting up, complete all as specified and as directed.

S&F MCB Single Pole & Neutral, 40 Amp, 240 Volt, AC, 'B' Series for fixing on MCB DB’s, 10 kA, 50 Hz and connecting up, complete all as specified and as directed.

S&F MCB DB 8-way, Single Pole & Neutral, Double Door type, Regal Grey Colour, Sheet Steel Phosphatised, Powder Coated with 200 Amp rate Bus-bar, Neutral Link Earth Bar & Din Rail duly embedded in Wall including Concealed upto Wall Surface including connecting with existing Cable Incoming and Outgoing with Cable Lugs as per the requirement and and Making Good Disturbed Surfaces of Walls/Roofs/ Floors, etc. so as to match with the existing Finishes, complete all as specified and as directed.

S&F Load Line 4-way Enclosure Double Door with Incomer MCCB 100 Amp rating, 16 KA, 4 Pole and suitable for 415 Volt 50 Hz AC Supply including taking down old unserviceable one, complete all as per specified and as directed.

M&L Earthing with Galvanised Steel Earth Plate Electrode 600x600x6.3mm buried directly in ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50 mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, Funnel with GI Watering Pipe 20mm bore (dia) medium grade including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion including taking down/out unserviceable Earthing, complete all as specified and as directed.

Biju Construction & Co

M/s Shreeji Construction Co