REPAIR TO TOILET, PLUMBING, SOIL WASTE PIPE AND MISC B/R WORKS IN WING - III AT ARTY CENTRE UNDER GE NASIK ROAD

Amount

Taking up or down 25mm or 32mm dia tubes galvanized iron and connections & removing/ shifting to site/store incl cleaning for relaying/refixing height up to four storey complete all as specified and directed by Engineer-in-charge. Note :- 1. Rates quoted are inclusive of taking out bib taps,PVC float valves and fitting as per site condition.

All as per Item No. 01 but 20 mm dia

All as per Item No. 01 but 15 mm dia

Re-fixing only 25mm or 32mm dia tubes galvanized iron as directed incl renewal of threading/tread cutting at ends of GI pipes fixed to walls or laid in floor and jointing including S&F new fitting such as socket, bends, elbows, union etc all as specified and directed. Note :-1. Serviceable GI pipes taken down in item No 01 shall be reused. 2. The rates quoted are inclusive of all new fittings required and cutting threading to existing pipe.

All as per Item No. 04 but 20 mm dia

All as per Item No. 04 but 15 mm dia

S&F for tubes 25 mm dia medium grade galvanized with all fitting fixed to walls, ceiling and laid in floor of including cutting, holes in concrete/brick wall/roof and making good if required height up to four storey bldgs all as specifed and directed by Engineer-in-charge.

All as per Item No. 07 but 20 mm dia

All as per Item No. 07 but 15 mm dia

S&F 25mm Gun metal globe or gate valve cost copper alloy with iron wheel head, screwed both ends for iron pipe and fixed in repairs all as specified and directed by Engineer-in-charge.

S&F in repairs bib taps cast copper alloy , Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F in repairs flush pipe of polyethylene of low or high density of PVC 32mm dia suitable for for low level flushing cistern complete all as specified and directed by Engr-In-Charge.

Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed by Engr-In-Charge.

S&F ready made PVC conection 15 mm bore 450 mm long with end brass nuts, screws and PVC washer complete all as specified and directed.

S & F 15 mm dia Stop valves fancy type,chromium plated screwed down,high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed.

S & F in repairs wash hand basins,Vitreous china (flat back or angle back type) any size,inclunding cutting for and pinning in ends of brackets or erecting stand , including supply & fixing wastecoupling and pipe.

S & F 15 mm dia Pillar taps,cast copper alloy fancy type with capstan heads,chromium plated,screwed down high pressure,with or without lettered Hot or Cold with long screwed shanks and fly nuts,screwed for iron pipe and fixed.

S&F in repairs vitreous china squatting patern "Orisa pattern" size 580mm x 440mm with trap white with intergral foot rest complete all as specifed and directed by Engineer -in-charge.

S&F in repairs coloured PVC valve less, syphonic action fushing cistern , low level, 10 ltr capacity with inlet, ball valve,, float, chain and pull and brackets complete all as specified and directed

S&F in repairs Stainless steel sink made out of 1.0 mm thick sheet for kitchen including waste pipe CI cantilever brackets and waste coupling etc complete and making good to the side of wall,connecting union to pipe, including bedding in CM to dwarf wall. Overall size 495mm x 420mm and bowl size 410 x 330 x 160mm

M&L in repairs for PVC (SWR) floor trap, plain with grating including demolition of old trap and jointing with solvent cement of outlet 75/100 mm dia proper joint of out let connection complete all as specified and directed by Engineer-in-Charge. Note : Height of building upto four storey (4th).

Taking down existing PVC/AC rain water , waste and vent pipe of any bore complete all as specified and directed by Engineer-in-Charge. Note : Height of building upto four storey (4th).

S&F PVC (SWR) pipes 110 mm dia. double socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-Charge. Note : Height of building upto four storey (4th).

S&F PVC (SWR) bends 110 mm dia any radius

S&F PVC (SWR) 110 mm dia vent cowl

S&F PVC (SWR) junction single (single T) equal or unequal 110 mm bore.

S&F PVC (SWR) bends with access door 110 mm dia any radius

S&F PVC (SWR) pipes 75 mm dia. double socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-Charge. Note : Height of building upto four storey (4th).

S&F PVC (SWR) bends 75 mm dia any radius

S&F PVC (SWR) 75 mm dia vent cowl

S&F PVC (SWR) junction single (single T) equal or unequal 75 mm bore.

S&F PVC (SWR) bends with access door 75 mm dia any radius

Dismantling floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premises.

M&L for Screed bed or bedding layer of cement mortar 15 mm thick for laying floors finishes in cement mortar 1:6.

M&L for rendering 15mm thick in CM 1:4 as in backing coat on fair surfaces of brick wall.

M&L for Non Skid ceramic tiles coloured 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for Non Skid ceramic tiles coloured 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for glazed cermic tiles coloured size 300x200x6 to 7mm thick in vertical surface, set and jointed in neat cement slurry & pointed with coloured cement to match

M&L for special treatment to sunken portion with 10mm thick plaster in CM 1:4 by using Ditachment DM 1% by weight of cement and surface made smooth after curing period two coat of Ditachment DS shall be applied @2.50 Kg/Sm. The paste like consistancy like is made by using 2.5 Kg of Ditachment DS powder in one litre of admixture (The admixture is made by dissolving 1 part by volume of Nafufill SBR & 4 part by volume of water). After 7 days curing, testing shall be done by flooding for 72 hours. Finally protective plaster coat of 10mm thick in CM 1:4 shall done by using Ditachment 1% by weight of cement over layer of Detachment DS. All joints of CI Pipe, Nahani trap, WC connection etc. shall be filled by mixture of cement, fine sand and 10% Nafufill SBR by weight of cement. 32mm dia and 500mm long GI Spout light grade shall be provided in all sunken slabs to drain off water. including demolition of cement concrete in sunken slab and filling of mass concrete 1:5:10 all as specified and directed by Engr-In-Charge.

Dismantling stone slabs and tiles of any thickness in floors, aprons etc. laid bedded and pointed in any mortar

M & L for 30 cm x 30 cm x 20 to 25 mm thick chequered tiles of rubber moulded with grey cement and pigment are polished, decorative set and pointed in neat cement sluurry in floors etc including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engr-In-Charge.

S&F Machine cut cudappa stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed by Engr-In-Charge.

M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite 18 to 20mm thick. all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations. (Stone slabs so provided shall be not less than 900mm in length)

Demolition of cement concrete in ground floors and pavings not exc.15 cms thickness (below or above GL.)

M&L for cement concrete type D-2, 1:4:8 (40 mm graded agg) in foundation, filling and mass cocrete and sub base etc.

M&L for rough finished shahbad stone slab 18-25mm thick incl, 15mm thick bedding laid and jointed & pointed in CM 1:4 all as specified & directed.

Dismantling water tanks and removing to store of capacity 1000 litres

Dismantling water tanks and removing to store of capacity 500 litres

Dismantling water tanks and removing to store of capacity 2000 litres

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 litres including 20/25mm dia PTMT float valve complete set all as sepecified and directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 2000 litres including 20/25mm dia PTMT float valve complete set all as sepecified and directed

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 litres including 20/25mm dia PTMT float valve complete set all as sepecified and directed

Taking down Chowkhats with shutters without taking off shutters from the frames exc 1.5 Sqm each not exc 4 Sqm each

Taking down Chowkhats with shutters without taking off shutters from the frames (not exc 1.5 Sqm each).

Taking down shutters of any descriptin exc 1 Sqm and n. exc 2 Sqm each.

Cutting holes in bk walls built in CM or cement lime mortar and stoned walls built in lime mortar depth of embedded portion of hold fasts or lugs measured from the faces of jamb into the wall exc half brick but n.exc one brick for inserting hold fasts and making good dismantled portion incement mortar 1:3 or cement concret 1:2:4 type B-1 as required.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS suquare tube, suppling and fixing in opening as per specification and drawings .

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing as directed by Engineer in-charge.

S&F factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered panticle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure teated complete all as specified and directed.

S&F 2nd class hardwood plain, solid,straight, chowkhats & frames, wrought,framed, rebated on the solid,rounded or champered,put togetherwith glue pinned at joints , supplied and fixed.

S&F 2nd class HW glazed and skelton shutters, 35mm thick open rebated and prepare to receive glass, gauze etc without sashbars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members as specified in SSR Part-I section 8, clause 8.24 (a) supplied and fitted to chowkats. all as specified and directed by Engr-in-Charge.

S&F solid PVC frame of size 50 x 95 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS suare tube , with necessary arrangement for fixing of glass for louer type window / ventilator and additional PVC beading around the frame for fixing of wire mesh supplying and fixing in opening all as specified & directed (note :- Glazing / wiremesh shall be measure & paid separately).

S&F MS steel flat iron hold fasts confirming to FE-290 Gde E165.

Preparing the surfaces of wood and wood based material,steel and iron work, new or old and treated with tar or coal tar black paint treating ends of pasts, backs of chowkhats etc area tarred exc 0.1 Sqm each.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised

S&F 100mm size butt hinges stainless steel

S&F 150mm aluminium anodisd, barrel tower bolts of excturded section.

S&F aluminium alloy,anodised, sliding door bolt with hash, staple(bolt type) and fixing clip of sheet,cast over exturded sectionand fixing bolt and sliding bolt of exturded section or cast alumimium alloy and fixing 300 mm length

S & F in repairs Stainless steel wire cloth. 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

M&L for painting to wood and wood base surface of any description not otherwise described, over 10 cm width or girth preparation of new surfaces, priming coat pink primer and applying two coat of synthetic enamelled paint

Resecuring without taking down of chowkhats or shutter steel or wooden window area not exceeding1.5 Sqm each including necessary repairs to hinges, welding and nut/bolts etc all as specified and directed. Note building height up to four storey bldgs

Dismantling boarding, cup board self/ shutter any description, fixed in any position with nails/screw etc complete all as specified and directed.

M&L for 25mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including 4mm thick teak wood beading on all edges as in kitchen cabinet, cup board self, book self pelmet box etc complete all as specified and directed.

S&F 75mm size butt hinges stainless steel

S&F100mm aluminium anodisd, barrel tower bolts of excturded section.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodised

Dismantling of steel window/ventilators any description and any size complete all as specified and directed.

M& L for steel window in Ahmadbad section with double shutters, side hung including box type hinges with steel handles steel peg stay and complete with glazing bars (one side glazed shutter and other side fly proof shutter with and 15x3 mm flat iron fillet around and centre for fly proof shutter including preparation of newly surface , applying two coat of synthetic enamel paint over coat of prime confirming to IS steel window and section complete all as specified and directed by Engineer -in-Charge. Note :- glazing and wire gauging shall be measured and paid separately.

S&F in repair 20/25 mm dia medium weight, aluminium powder coated of approved colour as in drapery rod complete all as specified and directed.

S & F aluminium powder coated brackets, of colour and design as approved suitable for curtain rods of 20/25mm dia complete all as specified and directed.

Hacking out old broken glass,n.exc 0.5 sqm area each (any thickness, size, quality or description) from metal/ wooden frame inculding punching or drilling out old glazing pins / spring clips etc. Height upto four storey buildings.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty/ wooden beading where is required in squares n.exc. 0.5 Sqm in each pane. Height upto four storey buildings.

Ditto as in Item No 77 above but figured glass,pin headed type

M & L for 2nd class hardwood of area not exc 3 sq cm in plain fillets square, rectangular or triangular in section clean sawn secured with nails or breads and two coat of synthetic enamel paint over a coat of pink primer including taking down of wooden fillets any size complete all as specified and directed.

Demolition of brick work/stone work built in any cement mortar including coping.

M & L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius,built in cement mortar 1:6.

Taking down cement or cement lime plaster,any description on brick or stone walls,etc including racking out joints,hacking for key,scrubbing down with water,etc.

M&L for rendering 15mm thick cement mortar on brick masonry surfaces in CM 1:6 and finishing even and smooth without using extra Cement.

M&L for rendering 5mm thick cement mortar on Ceiling surfaces in CM 1:6 and finishing even and smooth without using extra Cement.

M&L for applying two coats of cement paint over coat of priming with alkali resistant primer on walls including preparation of new plastered surfaces.

M&L for applying two coats of white wash on new surfaces of ceiling

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS.47,665.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Vinod Enterprises

Kaushalya Buildcon

Alpha Construction

M/S SAMEER SUBHASH PATANI

SVT ENGINEERS AND CONTRACTOR.

MANOVANDANA CONSTRUCTION

Srujan Associates

M/S R.K.S. CONSTRUCTION

VIJAY ENTERPRISES

Bidder Name

M/S SAMEER SUBHASH PATANI

SVT ENGINEERS AND CONTRACTOR.

Alpha Construction

M/S MK Nair

Vinod Enterprises

Srujan Associates

VIJAY ENTERPRISES

M/S R.K.S. CONSTRUCTION

Kaushalya Buildcon

MANOVANDANA CONSTRUCTION