SPL REPAIR OF BLDG NO P-132 SPL REPAIR OF P-51, P-72, P-73,P-37 of B CSR CERTAIN REVENUE WKS AND MINOR WKS ADD ALT DRAINGE LINE P-69 to P-70 AT LICHUBARI AREA IN JORHAT MIL STN UNDER GE JORHAT

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out as in soft/loose soil.

Excavation in post holes not exceeding 0.5 cum and getting out and returning filling in, ramming earth in layers not exceeding 25 cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good in hard/dense soil.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level n. exc. 1.50 m above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil.

Demolition of cement concrete (reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level)

Material and labour for Plain Cement Concrete M-7.5(Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete

Material and labour for Precast Reinforced Cement Concete cover slab type M-20(Nominal Mix) using 20 mm graded stone aggregate, set in Cement Mortar (1:4) complete all as specified and directed.

Material and labour for TMT Bars Fe 500D 6mm & 8mm dia cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Material and labour for old Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Material and labour for old brick work with bricks class designation 75, size as per old size brick, straight or curved on plan exceeding 6 m mean radius half brick thick walls built in Cement Mortar 1:4 complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal outside of MOD land complete all as specified and as directed.

Material and labour for Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately

Material and labour for Rendering 5 mm in Cement Mortar 1:3 on fair faces of brick work or concrete ceiling surfaces finished fair

Supply only integral liquid water proofing compound complete all as specified and directed.

Material and labour for Preparation of new surface and applying two coats plastic emulsion paint over a coat of primer ver a coat of 1.5 mm thick cement base wall putty on wall surfaces of any description over 10 cm girth or width complete all as specified and directed.

Material and labour for Preparation of new plster ceilig surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and preparation of old surfaces and two coats plastic emulsion paint over a coat of primer ver a coat of 1.5 mm thick cement base wall putty on wall surfaces of any description over 10 cm girth or width complete all as specified and directed.

Material and labour for Preparation of new surface and applying 3 coats white wash on walls complete all as specified and as directed.

Material and labour for preparation of old ceiling surfaces and applying a coats of white wash complete all as specified and directed.

Material and labour for complete removal of existing finishing of internal wall surface of building/structure by mechanical appliance and applying 2 coats of cement based paint over a coat of alkali based primer of any description over 10 cm girth or width complete all as specified and directed.

Material and labour for preparation of new surfaces and and applying 2 coats of cement based paint over a coat of alkali based primer complete all as specified and directed.

Material, labour and fixed of Rolled mild hollow steel sections steel of grade YSt 310 conform to IS 4923-1997 in roof trusses (framed), trussed, purlins, bracing and fastenings including distance pieces, cleats etc. Note:- The steel trusses shall be provide as per TD no CESZ/STD/26.

Material & labour of Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W (Gde- E- 250) quality- A

Material & labour of mild steel screw bolts (machine made) with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 22.5 cm and not exceeding 30 cm long, dia of neck 16 to 20 mm complete all as specified and as directed

Supply and fixing of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and pitch length 75 mm c/c of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Material, labour and fixed of power coated aluminium snap grid frame work for false ceiling, size of grid 605 x 605 mm, including aluminium main/closs tee of size 35mm x 23mm x 1.5 mm ( minimum) aluminum BULBED TEES section and aluminium angle of 25mm X25mm X1.5mm thick, sutiable type GI wire hanging arrangement with adjuster all as specified in clause no 10.38 in SSR part-I and including 4 mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer including taking dwon existing false ceiling system complete all as specified and directed. Make (i) ALUMINUM SNAP GRID:- HINDALCO/ INDALCO/ JINDAL (ii) Non Asbestos Fibre Cement Board as per IS 14862:-ARMSTRONG/ SAINT GOBAIN (GYPROC)/EVEREST / VISAKA Industries Ltd

Stripping out tarfelt from old roof surfaces and removing unserviceable materials from site of work in low laying in outside MOD area complete all as specified and as directed.

Material and labour forrendering 15 mm(Avg) thick in Cement Mortar 1:4 finished even and smooth witht using extra cement after preparation of roof surface with brushing and applied neat cement slurry with 3.0 Kg of cement per Square Metre existing surface complete all as specified and as directed

Supplying and laying 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.6 kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt laying over a coat of bituminous primer @ 0.40 Ltr / Sqm and two coats of Bitumen based UV reflective paint with aluminium finish over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc all as specified in Para 11.44.5 of SSR Part I complete all as specified and as directed.

Demolition of cement concrete (reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level)

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 100 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in flooring, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for75 mm thick plain cement concrete 7.5 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Material and labour for Hard core of gauge not exceeding 63 mm of broken stone or boulders , spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface

Material and labour for Sand filling under floors or in fdns incl watering and consolidation

Plain Cement Concrete M-10(Nominal Mix) using 20 mm gaded stone aggregate as in Surface channel and drain

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.

Add or deduct for each 25 mm girth or part thereof over or under 30 cm inner girth in cement concrete complete all as specified and directed.

Material and labour for Plain Cement Concrete M-15(Nominal Mix) using 12.5 mm graded stone aggregate as in making good window opening, lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs, water trough and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

Material and labour for pre-polished chequered Cement Concrete tiles of 25 mm minimum thick, size of (square/ rectangular) area of each tile exceeding 0.09 Sqm but not exceeding 0.16 Sqm double layer machine pressed set ( as per IS 1237-2012), jointed and pointed in neat cement slurry in floors and cut & polished in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.06 Sqm and not exceeding 0.11Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.18 Sqm and not exceeding 0.36Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.18 Sqm and not exceeding 0.36Sqm , as in skirting etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material & Labour Glazed ceramic tiles 450x300x7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and as directed.

Mild steel work as in bands, straps, supports or stays for RWP, ventilating pipes, clamps, hold fasts, wall ties conforming to Fe-290 Gde E-165

Supply and fixing of aluminium door shutter with powder coating (minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed openable shutter . (ii) Opening of door exceeding 2.52 Sqm but not exceeding 3.15 Sqm (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vi) Rest all as specified in drawing no CESZ/2015/TD/005 Sheet no 1/5 Note Nos :- (i) , Only Glass, door closed, tower bolt shall be measure and paid separately under relevant items of BOQ .

Supply and fixing Powder Coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Supply and fixing of aluminium sliding window with powder coating (minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged (fly proofing) sliding shutter. (ii) Opening of windows exceeding 0.90 Sqm but not exceeding 1.50 Sqm (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vi) Rest all as specified in drawing no CESZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5 & 5R/5. (vi) Rest all as specified in drawing no CESZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5 & 5R/5. Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass wire mesh shall be measure and paid separately under relevant items of BOQ .

Supply and fixing of aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum thickness of powder coating 50 micron) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and complete all as specified and directed.

Supply and fixing of Glazing with sheet glass 5 mm thick ordinary quality in panels of aluminium windows, ventilator, etc. fixed with glazing clips, rubber beading and EDPM gasket in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Supply and fixing of 8 mm thick toughened glass for aluminium door fixed in square exceeding 0.5 Sqm in each pane complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 150 mm complete all as specified and directed.

Supply and fixing of Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

Supply and fixing of Aluminium extruded section body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed. Note for item no 62 & 63:- All fitting & fixture such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector, holding clamp shall be provide as per site requiredment as as directed by AGE and same shall deem to be included in quoted rate.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning and removing all scales, dirt etc. from the tank and from mouths of circulating pipes etc., exceeding 1000 litres but not exceeding 2000 litres capacity

Supply and fixing of PVC ball valve for 20 mm dia GI pipe all complete complete all as specified and directed.

Supply and fixing of uPVC of type-B for use in soil and waste discharge systems, single socket, 110 mm bore in any length including rubber ring joints and fixed to walls with clips and other standard material and including taking dwon old rain water pipe & removal from site all as specified in IS 13592 complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )bend for 110 mm bore uPVC pipe complete all as specified and directed.

Subtotal of Sch A part-I

SCHEDULE 'A' PART - II FOR B/R PORTION (Sl No __ to ____)

Taking down carefully unserviceable copper / aluminium point wiring (light, fan, bell socket or power) including all fittings such as switches, socket, ceiling roses , regulators and switch boxes etc complete and making good the disturbed surfaces complete all as specified and as directed.

Material and labour for concealed point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing complete switch for One light/fan/bell point controlled by one way switch. Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.

All as per item no 71 here-in-above but One 3 pin socket outlet 5 amps on the same board with other switches

All as per item no 71 here-in-above but above but for one 5 amp socket independent complete all as specified and as directed.

Material and labour for concealed point wiring complete with 2.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 2.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing 3 pin socket outlet 15 Amp independent:- Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.

Supply and fixing of switch piano flush single pole one way 5 amps complete all as specified and as directed.

Supply and fixing switch socket outlet multipurpose 3 pin 15 Amps /5 Amps controlled by one switch.

Supply and fixing switch socket outlet multipurpose 3 pin 5 Amps /5 Amps controlled by one switch.

Supply and fixing in repair bell push flush type 5 Amps complete all as specified and as directed.

Supply and fixing in repair call bell, ding dong AC 230 volt single pole (ding dong type).

Material and labour for Electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x50mm three terminals complete all as specified and as directed.

Supply and fixing of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 20Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 120 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No LDL-20-CDL of Crompton/ BCLAB 20W WH LED P of Bajaj or equivalent model of make list as given in PS as approved by GE.

Supply & Fixing of LED street light fitting ( Building Security light) of 30Watt with LED lamp’s & driver and made of pressure die-cast aluminum housing, IP 65/IP 66 road way luminaries with UV stabilized polycarbonate cover or toughen glass cover & high power LED’s as light source with 110 Lumen per watt and electronic driver with efficiency > 85% . The light fitting shall be fixed on wall/pole with and including 25 mm dia( or higher size as per manufacturers recommendation) light grade GI pipe (bend to shape or as per manufacturers recommendation ) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 40 x 5 mm MS flat) nuts, bolts & washers including painting the clamps with two coat of aluminium paint over a coat of red oxide primer and including taking up old light fitting complete all as specified and as directed Make:- Model No- LSTM-30-CDL M of Crompton Greave/ ENXT P 30L WH CR PC SD of Bajaj or equivalent model of make list as given in PS as approved by GE.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and necessary connecting PVC insulated Flexible cable for connection from ceiling rose to fan and connecting complete all as specified.

Supply and fixing of sub main wiring with two single core 4.0sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed 1100 volts grade IS-694 marked in PVC double lock casing caping and accessories accessories including one single core 4.0 sqmm copper conductor cable FRLSH as earth wire and including taking out old sub-main wiring complete all as specified and as directed. NOTE:- (a) All runs of copper conductor and one run of conduit shall be measured as one run length.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 8 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length and including taking out old DB complete all as specified and as directed.

Supply and fixing of MCB SP of rating 6 to 32 Amps 240 V complete all as specified and as directed.

Supply and fixing MCB DP 40 to 63 amps 415 volts 10KA breaking capacity.

Material and labour for Earthing as in repair complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connetced with earthing wire 4.0mm dia as earthing lead by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 15 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.

Material and labour for Sand cushioning to the full width of trenches for protection of cables including punning down complete all as specified. Note :- Thickness of sand cushioning shall be the thickness after punning down.

Material and labour for laying of Class designation 75 bricks, old size, flat, common clay laid in trenches across the trench as cable protection

Material and labour for laying of LT XLPE insulated armoured heavy duty cable 1100 volt grade ISI marked with alumimium conductor multi strand cross sectional area 16 Sqmm x 4 Core

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

MS J B CONSTRUCTION AND CO