SPECIAL REPAIRS TO JCOS ORS MD ACCN QTR NOS P42 P44 P45 AND P46 OF 6 GR AT ROORKEE PROVN OF CYCLE STAND AND PROVN OF AIR CIRCULAR AT A LINE NOS 05 07 K9 TDS AND NEW CHARGE AT RTS AND D SAHARANPUR IN THE AREA OF AGE BR III UNDER GE ROORKEE

Amount

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for brick work with old size sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed

Demolition of un-reinforced concrete including tiles/kota stone (if any) etc in ground floors and pavings n.exc 15cm thickness (below or above ground level) and removal of rubbish out of defence land complete all as specified and directed

Taking down cement or cement lime plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and M&L for 15 mm thick rendering in cement mortar (1:6) on wall surfaces of any description, finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on wall surfaces of any description, finished even and smooth (without using extra cement) complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and M&L for 15 mm thick rendering in cement mortar (1:4) on wall surfaces of any description, finished even and smooth (without using extra cement) complete all as specified and directed.

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises and M&L for non skid joint free coloured ceramic tiles 8 mm thick (square/ rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm in floors etc, laid over anf including 15mm thick screed bed in cement mortar (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises and M&L for joint free coloured glazed ceramic tiles of size 450x300x7mm thick in vertical surface, laid over and including 10mm thick sreed bed or backing in cement mortar (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for 18-20 mm thick machine cut granite stone slab (table rubbed and polished), laid over and including 15mm thick screed bed in cement mortar (1:6) and pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone slab complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:3:6) type C-2 (using 40mm graded aggrete) as in plinth protection / path etc, laid in panels and finishing even & smooth without using extra cement complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutters from the frame), exc 1.5 Sqm but n.exc 4.0 Sqm each complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutters from the frame), n.exc 1.5 Sqm each complete all as specified and directed.

Cutting holes into or through brick walls exc half brick wall but n.exc one brick thick wall built in cement mortar or cement lime mortar and/or stone walls for inserting holdfasts and making good dismantled portion in cement concrete (1:2:4) type B1 complete all as specified and directed.

Taking down shutters of any description exc. 1 Sqm and nexc. 2 Sqm each complete all as specified and directed.

S&F pressed steel frame of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides and fixed to chowkat or frame complete all as specified and directed.

S&F 35mm thick IInd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, guage etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part - I Section - 8, clause 8.20 (a) complete all as specified and directed.

S/F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinfoced with MS square tube, supplying and fixing in opening as per specification and shown on drawing complete all as specified and directed.

S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & shown on drawing complete all as specified and directed.

S&F steel windows with side hung shutters including box type hinges with steel handles and steel peg stay with glazing bars dovetailed or welded complete all as specified and directed.

S&F steel windows with side hung shutters including box type hinges with steel handles and steel peg stay without glazing bars dovetailed or welded complete all as specified and directed.

S&F 3mm thick sheet glass, plain ordinary quality and glazing with oil putty/ wooden beads in squares n.exc 0.50 sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and directed

S&F mild steel work as in holdfasts., wind ties, cleats for securing purlins to wooden trusses or rafters and the like conforming to Fe 290 Gde E165 complete all as specified and directed

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed

M&L for preparing old painted wooden surface exc 10 cm width and grith and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for preparation of new steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

S&F 150 mm long floor door stopper of Aluminium alloy body tongue, anodised, with hard drawn steel spring fixed to door complete all as specified and directed.

S&F mild steel 300mm size ordinary rat tail rod pattern springs (helical door spring) including roller and roller plate complete all as specified and directed

S&F 125mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin anodised and fixed complete all as specified and directed

S&F 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin anodised and fixed complete all as specified and directed

S&F 125mm size aluminium alloy handles, fabricated type extruded section, ISI marked all as specified.

S&F 100mm size aluminium alloy handles, fabricated type extruded section, ISI marked all as specified.

S&F 200mm long aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed

S&F 150mm long aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F 250mm long alumninium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

S&F MS framed work such as grills, gratings with ends of bars shouldered and or riveted or forged into spikes, framed guard bar, barred iron door, ladders, hold fast, framed balusters, walk ways, railings, frame work of water tank and similar work conforming to Fe 290 Gde E165 complete all as specified and directed.

M&L for 60 mm thick machine pressed precast concrete interlocking paver block with grey cement and pigment of any shape and size conforming to IS 15658-2006 of M-35 Grade, laid over and including 20 mm thick sand cushioning complete all as specified and directed

M&L for 75mm thick PCC (1:4:8) type B- 2 (using 40mm graded stone aggregate) as in sub base etc complete all as specified and directed.

M&L for cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in cills, copings, sides of tiled path, bed blocks for hold fast, kerbs and similar work with fair faces including necessary form work, weathering, slightly rounded or chamfered angles and throating etc complete all as specified and directed.

Taking down old CI / AC/ PVC pipe of any dia and S&F new 110mm dia PVC (SWR) pipes sigle socketed in any length with rubber ring joints, fixed to wall or laid in floor complete all as specified and directed.

S&F in repairs, 110 mm dia bore PVC (SWR) bend of any radius (Tee, Double Tee, Elbow, Socket) complete all as spd. And directed

Taking down old CI / AC/ PVC pipe of any dia and S&F new 75mm dia PVC (SWR) pipes sigle socketed in any length with rubber ring joints, fixed to wall or laid in floor complete all as specified and directed.

S&F in repairs,, 75mm dia bore PVC (SWR) bends / elbow (ISI Mark) complete all as specified and directed.

Taking down old 15mm dia bore GI tubing of any description and S&F new 15mm dia bore GI tubing (ISI marked), medium grade with all fittings and fixed to walls and ceiling or laid under floor including connection etc complete all as specified and directed.

Taking down old 20mm dia bore GI tubing of any description and S&F new 20mm dia bore GI tubing (ISI marked), medium grade with all fittings and fixed to walls and ceiling or laid under floor including connection etc complete all as specified and directed.

Taking up or down 15mm dia ore steel tubing and connections of any description including cleaning etc and re-fixing in new or old position (Walls, ceiling floors, etc) including replacing defective connecting fittings (if reuired) complete all as specified and directed.

Taking up or down 20mm dia ore steel tubing and connections of any description including cleaning etc and re-fixing in new or old position (Walls, ceiling floors, etc) including replacing defective connecting fittings (if reuired) complete all as specified and directed.

M&L for cutting chases exc. 10 cm but n.exc 20 cm girth, pinning in brick wall for conlealed water tubing etc, making good to facing where required and pointing in cement mortar (1:3) and making good cutting in cement mortar (1:3) to match existing surfaces complete all as specified and directed

Demolition of reinforced cment concrete including precast concrete articles and M&L for precast cement concrete (1:2:4) type B 1 (using 20mm graded stone aggregate) as in landings, cover slabs for manholes, kitchen platforms and similar articles with plain faces including chamfers, weathering, throating etc and setting in cement mortar (1:4) with joints to match complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F in repair,, 15 mm dia bore cast copper alloy chromium plated fancy type stop valves with long shank and cup (concealed type) with capstan head, screwed down, high pressure screwed both ends and fixed complete all as specified and directed.

Dismantling water stoarage tank of 500 ltrs capacity and removing to store and S&F new Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top)of 500 Ltrs capacity including 20mm dia bore size PTMT ball valve, hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F in repairs, 15mm dia bore cast copper alloy fancy type pillar tap with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shank and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. Make : Prayag Cat Part No. 8903 or equivalent range in Jaquar, Johnson

S&F in repairs, vitreous china wash down water closet pan (Pedestal pattern) white with 'P' or 'S' trap including connecting to soil pipe, flush pipe etc and making good the disturbed surface to match with the existing complete all as specified and as directed.

S&F in repairs, 10 ltrs capacity PVC valve less syphonic action type flushing cistern low level, white with inlet ball valve float, handle, aluminium brackets for bottom support fixed with gitties embedded in wall with drilling machine etc complete all as specified and directed.

S&F in repairs, 15mm dia bore brass chromium plated bib tap (short body) fancy type with crutch or butterfly handle, screwed down high pressure complete all as specified and directed. Make: Essco (Jaquar Group) Cat Part No. TQT - 511 equivalent range in Prayag, Marc, Johnson.

S&F in repairs, 15mm dia bore stop cock or angle valve (ISI marked), fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends and fixed complete all as specified and directed. Make : Prayag Cat Part No. 8910 or equivalent range in Essco (Jaquar Group), Marc, Johnson

S&F in repairs, vitreous china wash hand basin, white flat back size 550x400mm (excluding taps, waste, pipe chain and plug) but including a pair of MS bracket etc complete all as specified.

S&F in repairs, brass chromium plated towel rail 600 mm long 20 mm dia and fixed to wall with CP steel screws etc complete all as specified and directed.

S&F in repairs, PTMT shelf 450mm size, fixed to wall with CP brass screws and PVC rawl plugs complete all as specified and directed.

S&F in repairs, 100mm dia ore cast iron floor trap with CP grating including jointing to waste pipe complete all as specified and directed.

S&F in repairs, 15mm size brass CP single lever over head shower including shower arm 300 mm long flat shape with flange 125mm size suitable for 15 mm bore pipe complete all as specified and directed. Make: Prayag Cat Part No. BS-79S or equivalent range in ESSCO (Jaquar), Pearl

S&F in repairs, PVC connection 450mm long with brass check nuts & washers at both ends suitable for 15mm bore pipe complete all as specified and directed.

S&F in repairs, stainless steel sink without draining board, made out of 1.00mm thick stainless steel sheet for kitchen or laboratory, overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm, with plug, waste fittings, waste pipe, washers including cantilever type cast iron brackets, connecting union etc complete all as specified and directed.

S&F in repairs, 20 mm dia mild steel curtain rod covered with coloured PVC sleeves, fancy type with and including mild steel matching to colour fancy type brackets, stops and necessary curtain rings, side caps etc, fixed in any length complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over 1 mm thick wall care putty complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats cement based paint over one coat of alkali resistant priming paint complete all as specified and directed.

M&L for complete removal of existing decorative treatment on walls, cornices etc of any description, preparing the surfaces to receive further decorative treatment and applying two coats of cement base paint complete all as specified and directed.

M&L for complete removal of existing decorative treatment on walls, cornices etc of any description, preparing the surfaces to receive further decorative treatment and applying two coats of oil bound distemer (White or tinted) over 1.5mm thick wall care putty of approved make complete all as specified and directed.

M&L for complete removal of existing decorative treatment on ceiling of any description, preparing the surfaces to receive further decorative treatment and applying two coats of white wash complete all as specified and directed.

M&L for complete removal of existing decorative treatment on walls, cornices etc of any description, preparing the surfaces to receive further decorative treatment and applying two coats of white wash complete all as specified and directed.

Removing the existing water proofing treatment of any description from roof slab, sweeping clean the roof slab surfaces and washing down with water to remove dust etc at any roof level and applying a coat of polymeric bitumen primer conforming to IS 3384-1985 @ 0.30 Kg/ Sqm followed by a coat of hot blown bitumen 85/25 @ 1.20 Kg/Sqm and laying of APP based polymeric water proofing membrane 3mm thick (weight not less than 3.60 Kg/Sqm) reinforced with polyster non woven fabric (weight not less than 150 gms/Sqm) unrolled and bonded to substrate with overlaps (not less than 100mm) sealed /fused by flame as per manufacturer's instructions. A coat of hot blown bitumen 85/25 to be applied on top of APP memberane @ 1.20 Kg/Sqm and finally finished with a coat of aluminium paint @ 0.200 Ltr/Sqm as per manufacturer's instructions complete all as specified and directed. NOTE:- (a) The unit rate shall be inclusive cost of all necessary scaffolding, T&P etc complete. (b) The work to be executed by expert team of manufacturer as approved by GE under close suprvision of Engineer-in-Charge.

Supply only liquid water proofing compound of approved quality complete all as specified and directed.

M&L for 15mm thick plastering in cement mortar (1:4) mixed with liquid water proofing compound @ 0.200 Ltrs per bag of 50 Kgs of cement as per manufacturer's instructions on fair faces of brick work or concrete surfaces/ on top of roof slab complete all as specified and directed. Note :- WPC shall be measured and paid for separately at supply only rates.

M&L for PCC (1:4:8) type D-2 (using 40mm graded stone aggrgate) as in foundation, filling, sub base of floor and mass concrete complete all as specified and directed.

M&L for 20mm thick rendering in cement plaster in cement mortar (1:3) mixed with liquid water proofing compound @ 0.200 Ltrs per bag of 50 Kgs of cement as per manufacturer's instructions on fair faces of brick work or concrete surfaces/ on top of roof slab complete all as specified and directed. Note :- WPC shall be measured and paid for separately at supply only rates.

M&L for carryingout water proofing treatment with epoxy coating in the manner as specified below:- (i) Preparing roof/wall surfaces by cleaning properly to remove all loose materilas, dust etc. (ii) Providing & fixing (if required) 12mm dia PVC Nozzle @1.5 mtr c/c or less depending upon the situation upto 40mm depth on the entire area of the sunken portion and injecting/grouting cement slurry admixture with DURA EV (Non shrink Polymeric grouting compound) with 40 PSI Pressure pump through the nozzles. (iii) Cutting off protruding portion of nozzle after setting of the grout and sealing the same properly. (iv) Making angular fillet or Gola in cement mortar (1:3) admixed with diluted DURAKRIT (1 part of Durakrit mixed with 3 parts of Water) at the junctions of the slab & wall. (v) Wetting the surface with water to make it SSD condition. (vi) Applying one coat of DURAKRIT- Acrylic Polymer Modified Cementatious (PMC) slurry as per manufacturer's instructions prepared by mixing 1 part of DURAKRIT & 2 parts of cement by weight on the sunken slab surfaces turned & finished up to 100mm height of wall from top of slab. (vii) Applying second coat of DURAKRIT - Acrylic Polymer Modified Cementatious slurry as per manufacturer's instructions prepared by mixing 1 part of DURAKRIT & 2 parts of cement by weight over the first coat at right angles. The second coat shall be applied after first coat of slurry has touch dried (usually after 4 Hrs). (viii) Carryingout ponding test for water leakage as per IS:3370 Part 1 for seven days as per manufacturer's instruction. Note:- (a) If there is any leakage/seepage observed during ponding test/guarantee period, the same shall be made good by the contractor at his own cost. (b) The unit rate shall be inclusive cost of all necessary scaffolding, T&P etc complete. (c) The work to be executed by expert team of manufacturer as approved by GE under close suprvision of Engineer-in-Charge.

M&L for applying a coat of hot blown bitumen 85/25 @ 1.20 Kg/Sqm and laying of APP based polymeric water proofing membrane 3mm thick (weight not less than 3.60 Kg/Sqm) reinforced with polyster non woven fabric (weight not less than 150 gms/Sqm) unrolled and bonded to substrate with overlaps (not less than 100mm) sealed /fused by flame as per manufacturer's instructions complete all as specified and directed

M&L for 18/19 mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and directed.

S&F 125mm long aluminium anodised hasp and staple including bolt to hinge plate and fixed with screws complete all as specified and directed.

Taking down cement or cement lime plaster on ceiling surfaces, hacking for key, scrubbing down with water etc and M&L for 10mm thick plaster in cement mortar (1:4) on ceiling on fair faces of concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Surface excavation n.exc 30 cm deep and averging 15 cm and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.50m wide and n.exc 1.50m in depth for foundations etc n.exc 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/ loose soil complete all as specified and directed.

Removing excavated soil material (soil) to a distance n.exc 50 m and deposited where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L for reinforced cement concrete (1:1½:3) nominal mix (using 20mm graded stone aggregate) as in foundation, footing, plinth beam, bases for columns and the like complete all as specified and directed.

M&L for reinforced cement concrete (1:1½:3) nominal mix (using 20mm graded stone aggregate) as in columns, pillars, piers and similar works complete all as specified and directed.

Use and waste formwork to sides of concrete foundation, footing, bases of columns, raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter to rough finished flat concrete surfaces complete all as specified and directed.

Use and waste formwork to sides of columns, posts, struts, piers and similar work, vertical or to batter to ough finished flat concrete surfaces complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8mm dia as in stirrups, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F rolled mild steel work as in tubular trusses including special shaped washers etc using ERW or induction butt welded tubes conforming to IS:1161- 1979 grade St.-240 complete all as specified and directed.

S&F rolled mild steel work as in tubular beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates using ERW or induction butt welded tubes conforming to IS:1161- 1979 grade St.-240 complete all as specified and directed.

S&F 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers in roofs, walls etc with grade of zinc coating 275 complete all as specified and directed.

S&F 0.63 mm thick galvanised, plain mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (lenth & girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

M&L for 50 mm thick cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in sub base of flooring and the like complete all as specified and directed.

M&L for 100 mm thick cement concrete (1:2:4) type D-2 (using 40 mm graded stone aggregate ) as in flooring, finished even and fair complete all as specified and directed.

Dismantling AC coorugated or semi corrugated sheets in roof covering including ridges/wall cladding complete all as specified and directed.

S&F FRP based with stainless steel MOC fin and internal fittings Air Ventilator, Throat size 21" to 24", max exhaust capacity 2700FM double jet sealer ball bearings as per manufacturer's instructions complete all as specified and directed.

Taking down old point wiring of any description and M&L for new concealed Point wiring with 1.5 Sqmm(Nominal area) PVC insulated and PVC unsheathed FRLS multi stranded copper conductor single core cable drawn through and including PVC non metallic conduit of 20 mm dia ISI marked with complete accessories,including sunk mild steel 1.6 mm thick terminal boxes with 3 mm thick bakelite sheet top cover ISI marked complete including PVC insulated and unsheathed single core multistranded copper conductor cable of size 1.5 sqmm green in colour as earth continuity conductor connected to common earth and earth dolly, including taking down of existing point wiring and their connected items/ accessories, fittings and fistures complete making good surface with white wash or any type distemper as per existing colour of building complete all as specified and directed for the following:-

One light point controlled by one one way switch

One fan point controlled by one one way switch

One 3/5 pin socket outlet 5 Amp on the same board with other swithes.

One 3/5 pin 5 Amps socket outlet on indepandant board.

One bell/buzzer point controlled by one push button

One light point controlled by two, 2 way switch

All as per serial item No. 103.00 above but with 2.5 Sqmm (nominal area) FRLS cable PVC for the 15 Amp 3/5 pin socket power point including 1.5 Sqmm copper conductor as per colour coding for earth continuity complete all as specified and directed.

S&F in replacement switch piano flush type polycarbonate single pole one way 5 Amps complete all as specified and directed.

S&F in replacement switch piano flush type polycarbonate single pole one way 15 Amps complete all as specified and directed.

S&F in replacement switch piano flush type polycarbonate single pole two way 6 Amps complete all as specified and directed.

S&F in replacement bell push flush type 5 Amps complete all as specified and directed.

S&F in replacement bell electric AC 230 Volts single pole ding dong type complete all as specified and directed.

S&F in replacement socket outlet polycarbonate 2 in 1, 3 pin 5 Amps flush type complete all as specified and directed.

S&F in replacement socket outlet polycarbonate 2 in 1, 3 pin 5/15 Amps flush type complete all as specified and directed.

S&F in replacement angular holders PVC / polycarbonate type with back plate, fixing on 3 mm thick sunmica hylum plastic laminated round sheet 75mm dia complete all as specified and directed.

S&F in replacement of in replacement of electronic fan regulator 230 volts , step type (5 step) socket type ,hum free 100/300 watt complete all as specified and directed.

S&F in replacement of Ceiling rose in poly carbonate 3 terminal brass, 6 Amps, 230 volts AC ISI marked, fixing on 3 mm thick sunmica hylum plastic laminated round sheet 75mm dia complete all as specified and directed.

S&F in replacement LED bulk head light fitting suitable for 12 Watt LED bulb, AC 230 Volt, cast Aluminium oval shape canopy,heat resistant glass with rubber gasket, B22 porcelain holder, wire mesh guard,polyurethane paint,including 12 W LED bulb, complete all as directed. Make: Mepro Cat No: BO-41 or equivalanet in C&S / Crompton/ Havells

S&F in replacement of LED Street Light Luminaries 25 Watt with pressure die cast housing along with prismatic polycarbonate diffuser and LEDs with secondary optics and IP65 protection including brackets made out of GI pipe light grade of suitable dia or as per manufacturer recommended, bent to shape incl 02 Nos MS flat bent to shape incl 02 Nos MS flat clamps, nut bolts, including making connection complete all as directed. Make: Bajaj Cat No:BCLST 25W LED I or equivalanet in C&S / Crompton/ Havells

S&F in replacement LED tube light fitting 1x20 Watt, AC 230 Volt, decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as directed

S&F LED bulb of 15 watt suitbale for batten / angular holder complete all as directed Make: C&S Chandra Series LTHPLEDLAMP15WB22 BULB or equivalent in Crompton/ Havells/ Bajaj/ C&S

S&F in replacement of type TPN DB 4 way double door metal type to flush wall complete all as directed by Engineer- in -Charge Make: Legrand IP 43, Cat Pt No 5076 70 or equivalent in C&S / ABB

S&F in replacement of in replacement of SPN DB 8 way double door metal type flush to wall complete all as specified and directed Make: Legrand, IP 43 Cat Pt No 507611 or equivalent in C&S / ABB

S&F in replacement of MCB four pole 63 Amps AC 230 Volts, 'C' curve series with 10 KA breaking capacity including necessary lugs/ thimbles complete all as specified and directed. Make:Legrand Cat Pt No 408702 or equivalent in C&S /ABB

S&F in replacement of MCB double pole 63 Amps Amps AC 230 Volts, 'C' curve series with 10 KA breaking capacity including necessary lugs/ thimbles complete all as specified and directed. Make: Legrand Cat Pt No 4086 39or equivalent in C&S/ ABB

S&F in replacement of MCB SP 6-32 Amps AC 230 Volts, 'C' curve series with 10 KA breaking capacity including necessary lugs/ thimbles complete all as specified and directed. Make: Legrand Cat Pt No 4085 92 or equivalent in L&T/ ABB

S&F in replacement of Sub main wiring with two runs of single core FRLS PVC insulated and unsheathed multistranded, copper conductor cable of size 6.0 sqmm LT, 1100V grade, down trhough and incl adequate sizes PVC non metallic conduit of 20 mm/approprite dia with accessories and fittings and one run of 4.0 sq mm single core multi stranded copper conductor cable as earth continuity conductor. Note: Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20 mm or more approprite dia shall be measured as one run length of submain.

Dismantling of Ceiling /Exhaust fan of any type & Size and depositing to MES fan store in safe custody also including hanging/ refixing them to its existing place after completion of all type of building and electrical work including making electric connections with suitable size of flexible wire complete all as directed by Engineer-in-Charge.

Taking down existing earthing of any description and M&L for new earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to GI earthing wire 4mm dia size by means of GI bolts, nuts, check nuts and washers, earthing wire protected by GI pipe 20 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6) type C1 in chamber of size not less than 300x300x300mm (internal dimentions), RCC (1:2:4), type B-1, reinforced with 6 mm dia MS round bars @ 15 cm c/c both way for cover with angle iron 40X40X5mm frame etc complete all as specified and directed by Engineer-in-Charge. Note: The unit rate includes earthing wire and protection pipe upto maximum 7.5 metre from earth plate, earth point / test point and chamber shall be made 0.50 mtr away from the earthing pit.

M/s Inderlal

RAJENDER CONSTRUCTION CO

Nanda Brothers

RAM PRAKASH AND ASSOCIATES

M/s MAA SHAKTI CONSTRUCTIONS AND SUPPLIERS

shreyansh construction