Construction of office Building for newly created Jal Shakti Sub Division Daulatpur in Tehsil Ghanari Distt. Una (HP)

Amount

Excavation in foundation, trenches in earth work in all kinds of soil,such as pick work,jumper work.blasting work in hard rock and soft rock and in saturated soil etc. i/c all leads and lifts , stacking the excavated soil not more than 3 mtrs. clear form the edge of excavation and then returning the stacked soil in 15 cm layers when required into plinth, sides of foundation etc. consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth as per the direction of the Engineer-in-Charge.

Excavation in earth work and filling in 15 cm. layers in foundation & plinths including ramming, watering and consolidating complete in all respect including carriage of materials within all leads and lifts and as per the direction of the Engineer-in-Charge.

Filling In Plinth With Sand Under Floors Including Watering Ramming Consolidating And Dressing complete in all respect including carriage of materials within all leads and lifts and as per the direction of the Engineer-in-Charge.

Providing and laying cement concrete 1: 3: 6 ( 1 cement : 3sand: 6 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts and as per the direction of the .Engineer-in-Charge.

Providing and laying cement concrete 1: 4: 8 (1 Cement : 4 Sand :8 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts and as per the direction of the .Engineer-in-Charge.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level within all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in :-

a). Foundation Footing And Basis Of Columns, Etc. And Mass Concrete within all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

Flat surfaces such as soffits of suspended floors, roofs, landing and the like floors etc. upto 200 mm thickness within all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

c). Columns, Pillars, Posts And Struts :- Square Rectangular Or Polygonal In Plan within all lead and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

d). Beams, Cantilever, Girders And Lintels :-Sides And Soffits Of Beams, Beam Haunching Cantilevers, Brssumers And Lintels Not Exceeding 1 Metre In Depth In All Heights From Floor

Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor within all lead and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

e). Stair Cases With Sloping Or Stepped Soffits Excluding Landing within all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

f). Edges Of Slabs And Break In Floors And Walls :-Under 20 Cm Wide within all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses, plinth and string courses and the like.

Providing And Laying Cement Concrete Work 1:1.5.:3 (1 Cement : 1.5 Sand : 3 Graded Stone Aggregate 20 mm Nominal Size) Mechanically Mixed And Vibrated For Compacting Concrete And Curing Complete Excluding Cost Of Form Work And Reinforcement For Reinforce Cement Concrete in:-

Foundations, footings bases of columns and the like and mass concrete within all leads and lifts complete in all respect to the entire satisfaction and as per the directions of Engineer-in-Charge.

Suspended Floor, roofs, landing and shelves and their support balconies, beams, girders, bressumers and contilever upto floor two level within all leads and lifts complete in all respect to the entire satisfaction as per the directions of Engineer-in-Charge .

Columns, pillars posts and struts upto all heights.

Lintels, beams, girders, bressumers and cantilevers upto all heights.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto all heights.

1st. class brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:6 (1 cement : 6 sand) within all lead and lifts complete in all respect to the entire satisfaction and as per the directions of the Engineer-in-Charge.

1st. class brick work using common burnt clay building bricks in super structure above plinth level upto floor two level in cement mortor 1:6 (1 cement : 6 sand) within all lead and lifts complete in all respect to the entire satisfaction and as per the directions of the Engineer-in-Charge.

Extra for brick work in superstructure above plinth level upto floor two leve (First class bricks) same as above

Half brick work using common burnt clay building bricks in super structure above plinth level upto floor two level in cement mortor 1:4 ( 1 cement:4 sand ) 2nd. Class brick work within all leads and lifts and complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

Providing wood work in frames of doors, windows and other frames wrought framed and fixed in position with second class deodar wood in all leads and lifts.

Providing and fixing pannelled glazed or panalled and glazed shutters for doors, windows and clerestory windows including black enemelled iron butt hinges with necessary screws 40 mm thick 2nd. class deodar wood within all lead and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer - in- Charge. 40mm thick

Providing And Fixing Wire Gauge Shutters Using Galvanised M.S. Wire Gauge Of I.S. Gauge Designation 85G. With Wire Of Dia 0.56 mm for doors, windows and clerestory windows including black enemelled iron butt hinges with necessary screws 40 mm thick 2nd. class deodar wood within all lead and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer - in- Charge. 40mm thick

6 mm Cement Plaster To Ceiling to all floor level In Cement Mortar 1:3 (1 Cement : 3 Sand) in all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge..

15 mm thick cement plaster in single coat on rough side of brick/stone / concrete wall for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with cement mortor 1:6 ( 1 cement :6 sand ) in all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge..

20mm cement plaster in two coats,backing coat 15mm and finishing coat 5mm thick on rough side of brck/stone masonry walls for interior plastering up to floor two level including arises internal rounded angles ,chamfers and /or rounded angles not exceeding 80mm in girth and finished even and smooth. with cement mortor 1:6 ( 1 cement :6 sand ) in all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge..

Providing And Laying Spartic Ceremic Tiles 5.5Mm.Thick In Flooring (300 X300Mm. Size)Treads Of Steps Laid On A Bed Of 12Mm. Thick Cement Mortar 1:3(1Cement: 3 Sand) Finished With Flush Pointing In White Cement in all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge..

Providing and Laying 600x600mm Matt finished tiles grade-IV of Somany/Kajaria or its equivalentof approved shade and pattern as per detail in flooring, treads of steps and landing laid on a bed of 12mm (Twelve millimeters) thick cement mortar 1:3 (1cement:3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement with pigment of required shade to match the shade of tiles complete as per HPPWD specification within all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.. .

White Glazed Tiles 200 mm X 200 mm X 6mm Thick And 200 Mm X 150 Mm X 6Mm Thick In Skirting Risers Of Steps And Dado On 12mm Thick Cement Mortar 1:3 (1Cement : 3Sand) And Jointing With Neat Cement Slurry within all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge...

Cement plaster skirting (upto 30 cms height ) with cement plaster 1:3 ( 1cement :3 sand) finished with a floating coat of neat cement including rounding of junctions with floor within all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

Wall painting (two coats) with premium enamel paint ofapproved brand and manufactureon undecorated wall surfacesto give an even shadeincluding thoroughly brushingthe surface free from mortardroppings and other foreignmatter and sand papered smoothincluding applying of putty asrequired for making thesurface within all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

Extra for painting with premium enamel paint of approvedbrand and manufacture onceiling and/or sloping roofs within all leads and lifts complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by throughly cleaning oil, greas,dirt,and other foreign metter with ready mixed paint brushing wood primer pink complete in all respect as per the direction of the Engineer-in-Charge.

Painting two coats excluding priming coat on new wood and wood surfaces with enamel paint to give an even shade including cleaning the surface of dirt ,dust and other foreign matter sand papering and stoping complete in all respect as per the direction of the Engineer - in - Charge.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge..

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 graded stone aggregated 20mm nominal size) including carriage of materials complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

P/F 40X3 Mm Flat Iron Hold Fast 40Cm Long Including Fixing To Frame With 10Mm Dia Bolts Nuts And Wooden Plugs And Embedding In Cement Concrete Block 30X10X15Cm. 1:3:6 (1Cement:3Sand:6 Graded Stone Aggregate 20Mm Nominal Size). complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge

Providing And Fixing Oxidized M.S. Sliding Door Bolts With Nuts And Screw Complete 250mmx16mm complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge

Providing And Fixing Oxidized M.S. Handles With The Necessary Screws Etc. complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge 125mm.

Providing And Fixing Oxidized M.S. Tower Bolts (Barrel Type) With Necessary Screws Etc. complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge150mmx10mm.

Providing and fixing M.S. pressed pariiamentry hinges with necessary screws etc. complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge 150x125x27x2.80mm.

Stones/Boulder filling under floor.

Providing and fixing wire fencing within all leads and lifts and complete in all respect to the entire satisfaction and as per the direction of the Engineer-in-Charge.

Steel work welded built up sections truses and frames work including cutting hoisting fixing in position and applying primimg coat of red lead paint in grating framed guard bars ladders railing brackets and similar work including all leads and lifts

Providing & fixing Cast Iron Man hole cover with frame Size of 500 mm internal dia should not be less than 23 Kg complete in all respect within all leads & lifts.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group - C

Wiring for twin control light point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit, with 2-way modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group -C

Wiring for light/power plug with 2 x 4 Sq.mm PVC insulated copper conductor or single core cable in surface/recessed steel conduit alongwith 1 No. 2.24 mm dia bare copper wire for loop earthing as required including carriage of materials within all leads and lifts.

Wiring for power plug with 4x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for circuit wiring with 2 x 1.5 Sq.mm PVC insulated copper conductor single core cable in surface/recessed steel conduit as required including carriage of material within all leads and lifts.

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

a) 2x6 Sq.mm

b) 2x10 Sq.mm

c) 2X16 Sq.mm

Supplying and fixing backellite batten/angle holder including connection as required.

Supplying and fixing of following sizes of PVC conduit along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required:- 25mm dia

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required.

Supplying and fixing 5 Amps to 32 Amps rating 240 volts, G series miniature circuit breaker of following poles in the existing MCB, DB complete with connections testing and commissioning etc. as required Category "A", single pole.

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:-

Double pole. Cat-A.

Triple pole & Neytral. Cat-A.

Supplying and fixing following rating, double pole (single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amps. Cat-A.

Supplying and fixing of following way triple pole and neutral, sheet steel MCB distribution board, 415 volts, on surface / recess, with provision for 4-pole MCB/Isolator/RCCB/RCBO as incomer and SP MCBs as outgoing, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- Double door-12 way (8+36),horizontal type

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- Double door-8 way

Earthing with G.I. pipe earth, pipe 4.5 mtrs length, 40mm dia including accessories and providing masonry enclousres with cover plate having locking arrangement and watering pipe etc.( but without charcal coke and salt) complete as required including carriage of materials within all leads and lifts.

Extra using salt and charcoal for pipe earth electrode as required, including carriage of materials

Supplying and laying 6 Sqmm G.I.wire at 0.50 mtr below ground level for conductor earth electrode, including soldering etc complete including carriage of materials within all leads and lifts.

Supplying and fixing of 1.5 ton split type Air conditioner as per LG make cat No.LSA18MIC compressor cordless remote complete complete in all respects or any other equipment make as per LG comprising to ISI with latest amendment suitable to operate on 230 volts +-10% AC supply capable to perform the function of cooling dehumidification Air circulation,ventilation and fitting in the size of nominal cooling capacity complete with 4 KVA automatic voltage stabilizer confirming to ISI specification,the stabilizer should have high voltage trip and MCB High low voltage trip and time relay,complete in all respect and approved by the Engineer-in-charge. Hot & cold of standred make including carriage of materials within all leads and lifts.

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required:-

a) Ceiling Fan 1200 mm sweep, Category-A

b) Ceiling Fan 1400 mm sweep, Category-A

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the connections, damages, testing and commissioning etc. as required:- Exhaust Fan, Light duty, (Domestic) 300 mm sweep complete including carriage of materials within all leads and lifts.

Supplying and fixing stepped type Modular fan regulator existing modular box including making connections etc. as required

Supplying and fixing Ding-Dong / Electronic musical bell, for suitable D.C./A.C. single phase,230 volts complete as required complete including carriage of materials within all leads and lifts.

Providing and fixing T-5 tube rod 28watt, connections,testingand commisioning etc.as required including carrige of material within all lead and lifts

Providing and fixing following wattages in the existing batton holder, wallbreacket, bulkhead fitting and CFL fittings etc. as required complete including carriage of materials within all leads and lifts.

CFL -15watt with ballast

CFL -23watt with ballast

P/F M.S fan box with M.S sheet included fan hook with bakalite fan sheet, complete etc. as required complete including carriage of materials within all leads and lifts.

P / L in trenches centrifugally cast ( spun) iron socket & spigot pipes class LA (Earth work in trenches and jointing of pipes to be measured and paid for separately). 100mm dia complete including carriage of materials within all leads and lifts.

P/F cast iron floor trap of self cleaning design with sand cast iron screwd down or hinged grating without vent arm complete i/c cost of cutting and making goods the walls and floors. 75mm dia complete including carriage of materials within all leads and lifts.

P/F china wash down water closet ( European type WC pan ) with "P" or "S" trap i/c jointing the trap with soil pipe in 1:1 (1 cement : 1 sand) (seat and cover to be measured and paid for separately). (Universal closet of standred make complete including carriage of materials within all leads and lifts.

P/F vitreous China wash basin with single hole pillar tap with CI or MS brackets painted white i/c cutting holes and making good the same but excluding fitting.Cornet 1008 of size 630x450/ 550 x 400mm of ISI marked complete including carriage of materials within all leads and lifts.

P/F Vitreous china pedestal for wash basin recessed at the back for reception of pipes & fittings (Cornet 1108 pedestal of ISI marked complete including carriage of materials within all leads and lifts.

P/F brass bib tap long nose ( superior or heavy ) 15mm dia code qqt-7041 2way bib cock of ISI marked complete including carriage of materials within all leads and lifts.(Jaguar make.)

P/F angle cock brass angle valve 15 mm without nuts and pipe.code qqt.7053 Angular stop cock ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing (Jaguar make) 15mm diameters C.P. brass Pillar tap with capstan head complete

Providing/Fixing soap trays(Vitreous China) :-Recessed soap tray 150 mm x 150 mm size).

Providing and fixing CP brass towel ring round code-AQN-7721 (Jaguar make).

Providing and fixing 600 mm x 450 mm bevelled edge miror of superior glass mounted on 6 mm thick A.C. Sheet or plywood sheet & fixed to wooden plugs with C.P. brass screws and washers ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing M. I. Union for wash basin or sink 32 mm dia heavy duty ISI marked complete including carriage of materials within all leads and lifts..

Providing and fixing PVC. connection pipe with brass union 300 mm length. 15mm nominal dia ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing C.P. stock cocks 15 mm dia. ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing 32 mm dia, lead waste pipes for wash basin or sink includingbrass checknut ISI marked complete including carriage of materials within all leads and lifts..

P/F 100mm sand cast iron grating for gully, floor or nahni trap ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing rubber plug sink for wash basin 32mm dia ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing to wall ceiling and floor 15.00 mm dia galvanised mild steel tubes ( light grade ) tube fittings & clamps including making good the wall, ceiling and floor heavy class:_

Providing and fixing 100 mm dia C.I. bends heavy class ISI marked complete including carriage of materials within all leads and lifts..

Providing / Fixing Cast Iron cowl 100 mm nominal diameters ISI marked complete including carriage of materials within all leads and lifts.

Providing lead caulked joint to spun iron or C.I. pipes and fittings including testing of the joints but excluding the cost of lead. 100 mm dia. ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing G.I. elbow 15mm dia. ( heavy class ) ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing G.I. tees 15 x 15 x 15mm. ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing G.I. union 15mm dia (heavy duty). ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing G.I. sockets 15mm dia (heavy duty) ISI marked complete including carriage of materials within all leads and lifts.

Providing and fixing G.I. nipples of 15mm dia (heavy duty) ISI marked complete including carriage of materials within all leads and lifts.

7.5cm long

10cm long

15cm long

25cm long

Providing and fixing of floating valve 15mm dia complete in all respect.

Proving & fixing PVC water storage tank of ISI : 12701 marked G.I. inlet and outlet connection 15 mm nominal bore ball valve mosquito proof PVC cover with locking arrangement including hoisting up to all heights above Ground level. 1000 ltrs. Net capacity tank .

Dinesh Kumar

shiven ohri

VARINDER PAL

Deepak Verma

Sushant Puri