DNIT FOR CONSTRUCTION OF SURFACE PARKING, BOUNDRY WALL, PATHWAYS, RCC ROAD, PVC TENSILE STRUCTURE , RAIN WATER HARVESTING, ENTRANCE GATE AND TOILET BLOCK ETC. AT NADA SAHIB GURUDWARA, PANCHKULA.

Amount

Providing Design, Detailed Engineering, Fabrication, Supply, Erection and Installation of Primary Steel Structure Work in Mild Steel built up tubular CHS Section including cutting, hoisting, welding, fixing in position. Drainage Gutter are mild steel with c channel , for dropping water should be PVC pipe. Applying a Two Coat of Duco Paint over one coat of Anti Oxide Duco Primer after Rust Cleaning Process. Providing Design and Fixing imported tensile fabric of weight not less than 700 GSM Fabric, Make Mehler or Equivalent .This Should also include cutting, welding and cables, Plates and necessary hardware for fixing the fabric as approved shape as per drawing, Membrane shall be cut and manufactured with High frequency PVC Welding Machine. Centre column 3 m both side projection tensile walkway .Tensile walkway size : 302 M X 6 M projection. 1. Tensile walkway size 222m x 3m Projection 2. Tensile walkway size 165m x 3m Projection 3. Tensile walkway size 136m x 3m Projection

PUBLIC HEALTH WORKS: Providing and fixing in position SWR UPVC soil waste vent or antisyphonage pipes as per IS -13592 including cutting, jointing, wastage, but excluding cost of lead jointing. ( Double socket B Type ) Make : Finolex, Astral, Supreme, Diplast

110mm o/d SWR UPVC pipe lines laid complete

75 mm i/d SWR UPVC pipe lines laid complete

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. Make : Finolex, Astral, Supreme, Diplast

For 110mm o/d pipes

110 mm o/d UPVC Heal Rest Bend

110mm o/d Single junction with door 110mm x 110mm x 100mm

110mm o/d Bend with door

110mm o/d Bend plain

110mm o/d Cowls

110mm o/d Collars

For 75 mm i/d pipe

75 mm i/d Centrifugally cast iron Heal Rest Bend

75 mm i/d Single junction with door

75 mm i/d Bend with door

75 mm i/d Bend plain

75 mm i/d Cowls

75 mm i/d Collars

Providing, Stringing out U.P.V.C. Pipes casting as per IS:15328-2003 class-SN-8 along the trenches and laying the same in Trenches to correct alignment and gradients, cutting and jointing including cost of specials complete as per specifications. Make : Finolex, Astral, Supreme, Diplast

110mm o/d pipe

160mm o/d pipe

ELECTRICAL WORKS : Wiring in 1.5 sqmm PVC insulated copper conductor cable, single core, 1100 volts in 25mm dia PVC pipe, Heavy gauge, ISI mark with modular accessories and GI sheet steel modular boxes of required size with modular inner & outer face plates complete (flushed). (Based on HSR - 31.1). Modular accessories should be either of make (Legrand (Arteor) / Schneider make LIVIA / Havell's Crabtree make Munaro / North-west / MK make or its equivalent as approved by the department).

(i) Fan Point :-

(b) Medium point

(ii) Light Point single control :-

(a) short point

(b) Medium point

(c) Long point

(iii) Light Point without control :-

(c) Long point

(v) Light Plug

(a) short point

(c) Long point

(vi) Power Plug

(c) Long point

Supply, Carriage, erection, testing and commissioning of LED fitting with integral / non-integral driver. The lumen output of LED should be minimum 100 lumens per watt and should be type tested from Government / NABL / UL accredited laboratory for LM79 & LM80 test reports and copy of same has to be submitted to the client department. The Fixture supplied with Electronic high efficiecy driver having Power factor >0.9, THD <10%. The sample of fitting can be got tested in the presence of representative of the department from NABL I UL accredited laboratory. The job includes cost of all material and erection of fitting with all accessories including anchor fasteners and connection to the nearest light point with copper wires. The work should be completed as per satisfaction of Engineer-in-charge.

Supply, carriage, erection, testing and commissioning 18W LED Downlighter Surface mounted round shaped Wipro make LD80-171-xxx-60-SM / Lux Max Make LUX-PL-SQ-18W(S) / Philips make SM251C LED20S- 6500 PSU WH or its equivalent as approved by the department.

Supply, carriage, erection, testing & commissioning of surface mounting LED Industrial Box Type Batten fitting 1x 18 Watt, (4 feet long), made of extruded aluminium heat sink body provided for efficient heat dissipation & integrated electronic driver suitable for single phase A.C. 230 Volts, 50 HZ supply, complete in all respect. The job includes cost of all petty material and labour required to complete the job to the entire satisfaction of Engineer-in-charge. (Wipro Make WIO921208 Single 4 feet LED lamp MAS LED tube rod 1200mm LL13-181-65-T5 / Philips Make TMC 501 P 1xT-LED 22W P3241 and Lamp MAS LEDtube 1200mm 18W865 T8 I – 2100lm / Bajaj Cat. No. BLRB-DB 118 or its equivalent make as approved by the department).

Supply, carriage, erection, testing and commissioning of 10W LED Baton mirror light fitting 2' (600mm) long. The fitting is to be fixed with suitable fixing arrangement as required at site and making connection to the nearest point with copper wires as per the satisfaction of the Engineer-in-Charge. The fitting should be of make Crompton LCTL-18-CDL or Twinkle Lux Max LUX-TLF-9 or Wipro LL20-221-xxx-65-NE or of approved make of department.

Supply, carriage, erection, testing and commissioning of 40W LED Capsule fitting Surface mounted totally enclosed luminaire (IP66). Wipro make LE20-491-XXX-57-G1 / Philips make WT550 C LED 40S CW PSU S1 PC / Crompton make LPFC-36-CDL or its equivalent Bajaj / GEmake as approved by the department. The job includes cost of suitable clamps to fix the fitting on steel structure including all labour and petty material required

Supply, carriage, erection, testing and commissioning of 40W LED High efficiency aluminium profile linear batten with polycarbonate diffuser for enhanced productivity. Ingress protection IP40 (Wipro Make Cat.No.LL24-541-XXX-57-CD / Philips make Cat.No. BN100C LED40S-6500 PSU L120 GR / Bajaj make Cat.No. BLTRU 40W NW VIVA or as approved in the department).

Supply, Carriage, erection, testing and commissioning of LED fitting with integral / non-integral driver. The lumen output of LED should be minimum 100 lumens per watt and should be type tested from Government / NABL / UL accredited laboratory for LM79 & LM80 test reports and copy of same has to be submitted to the client department. The Fixture supplied with Electronic high efficiecy driver having Power factor >0.9, THD <10%. The sample of fitting can be got tested from NABL I UL accredited laboratory by the department. The job includes cost of all material and erection of fitting in false ceiling after cutting the false ceiling as required including giving support of chain from ceiling or frame including connection to the nearest light point with copper wires and petty material required to fix the fitting properly. The work should be completed as per satisfaction of Engineer-in-charge.

Supply, carriage, erection, testing and commissioning of 33W - 36W LED 2'x2' fitting recess mounted. The fitting should be of make Wipro make CRCO10R036HP57G1 / Philips make RC380B LED36S -6500 G4 L60 W60 PSD OD / Bajaj make BCTBLR 36W LED FP WH or approved make of department.

S/I/T/C of LED street light light fitting of 36W rating with integral / non-integral driver and minimum 110 lumens per watt complete in all respect. The fitting is to be fixed on wall with bracket mounted on wall. The job includes cost of bracket made of GI pipe 32mm dia B-class 0.5m overhang L-shaped angle of inclination 120 degree with upper side of bracket 550mm overhang and lower side of 550cm long. The bracket is to be fixed on wall with 2Nos. anchor fastners grouted in wall. The job includes cost of LED fitting, GI pipe bracket and anchor fasterners etc. required to complete the same. The work should be completed as per satisfaction of Engineer-in-charge. Wipro Cat No.LR13-501-XXX-57-XX (35W) / Philips make Cat No.BRP046 LED 36 CW MR S1 PSU GR (36W) / Bajaj make Cat.No.BRTFG 36W LED (36W) or as approved in the department)

Supply, Carriage and erection of thermoplastic cable junction boxes IP 66/67 “weather proof”, for outdoor installation (with knockouts for cable entry) of various sizes for termination of cables. The box is to be fixed on truss / catwalk as required as per site. The job includes cost of junction box with petty material required to fix the box. The work should be completed as per satisfaction of Engineer-in-charge / Architect. (Hensel / Diplast or make similar to Hensel as approved by Engineer-in-charge).

Junction Box of size 104x104x70mm suitable for 1.5-4sqmm

Junction Box of size 200 x 160 x 98mm

Supply, carriage and erection of 70W-72W LED 6000K, die-cast aluminium street light luminaire complete with toughned glass and other material required to complete the job in all respect. The job includes the cost of install the fitting on the existing bracket on wall complete the job in all respect including cost of 1.5sqmm copper wire from light point to fitting. The fitting should be of make Crompton LSTP-72-CDL / Wipro LR02-781-XXX-57-XX-G2 (70W) Lux Max Cat.No.LuxMax-SLB-72 or of approved make of department.

Supply, fabrication and erection of GI (B-class) ISI marked Jindal make street light bracket 2" dia 0.9m overhang L shaped with angle of inclination 1000 and lower side of 80mm GI pipe 0.45m long slipped over the pole fixed with 2 Nos. 12mm dia nut-bolts. The top end of the 80mm GI pipe is to be covered with 2mm thick MS sheet and conical MS sheet 3mm thick is to be welded between 2" and 3" GI pipe to give mechanical strength. The job includes cost of all abovesaid material including painting of all MS parts and erection of the same on 7m high octagonal pole with all petty material required.

Single Arm Bracket

Double Arm Bracket

Supply, Erection, Testing & Commissioning of A.C. ceiling fan double ball bearing Energy Saver (5 star rating) complete in all respect without fan regulator. The fan should consume less power.

48" sweep (Ceiling Fan Havell's make ES - 50 Premium or its equivalent of Crompton make Aura Prime Antidust / Orient make Energy Star (White) / Usha make)

S/E of A.C. Exhaust fan (ISI Marked) suitable for single phase A.C. 230 Volts, 50 HZ capacitor, 900 RPM (Heavy Duty) complete with mounting ring frame with four fixing holes and automatic louver shutter but without regulator. The exhaust fan and its louver is to be fixed in the existing glazing with suitable MS frame of required thickness as per site including its painting etc. as per site requirement.

Size 380mm sweep (Havell's make Turbo Force 900rpm single phase or its equivalent of Crompton make EXHD380-6-1 / Orient make (Grey) / Usha make)

Supply, Carriage, Erection, Testing & Commissioning of Fresh air fan 230mm/250mm complete with guard. The fresh fan fan is to be fixed in ventilator with 12mm thick wooden board after making hole in board. The board is to be fixed screws etc. including painting of board with matching colour of fresh air fan. The job includes connection from nearest light point with PVC Cu wire including cost of all material (Havells make (Ventil Air - DS metallic) 230mm sweep / Crompton make Ventilus 10" / Orient make (Ivory) / Bajaj / Khaitan make as approved by the department).

Supply, carriage and erection of modular type 25A Switch with indicator with modular box and sheet complete in all respect. The box is to be recessed in wall complete with cost of petty material required to fix the same and labour involved. (Legrand (Arteor) / Schneider make LIVIA / Havell's Crabtree make Munaro / North-west / MK make as approved by the department).

Supply, carriage and erection of modular type 1No. 25A Socket (for AC Unit) with modular box and sheet complete in all respect. The box is to be recessed in wall complete with cost of petty material required to fix the same and labour involved. (Legrand (Arteor) / Schneider make LIVIA / Havell's Crabtree make Munaro / North-west / MK make as approved by the department).

Supply, carriage, erection, testing and commissioning of electronic time switch suitable for 1 phase / 3 Phase system comprising of 1 No. Digital timer clock with battery, 1 No. 32A / 63A 3pole Power contactor AC-3 duty and bypass switch enclosed in a readymade MS enclosure complete with all wiring. The work should be completed as per satisfaction of Engineer-in-charge / Architect.

Daily programmable Digital Time Switch timer with 1 No. 1 phase / 3 phase power contactor 32A - 3P complete in all respect. Indo Asian (TL032DB0) or its equivalent L&T / Havell's / Hager / Schneider as approved by the department.

Daily programmable Digital Time Switch timer with 1 No. 3 phase power contactor 63A - 3P complete in all respect. Indo Asian (TL064DB0) or its equivalent L&T / Havell's / Hager / Schneider as approved by the department.

Bidder Name

Amount

Krishna Construction Co(GSTN-06AALFK6441Q1ZP)

Lakhan Singh Govt. Contractor(GSTN-NA)

Sucha Singh(GSTN-NA)

K.S. Construction Company(GSTN-NA)

Krishna Construction Co

K.S. Construction Company

Sucha Singh

Lakhan Singh Govt. Contractor

K.S. Construction Company

Krishna Construction Co