WBPHED/EE/CMD/eNIT08/20-21

Amount

Supply & delivery of the following Pumping machinery, Electrical accessories etc. at site. a) Submersible Pumping Machinery, directly coupled with suitable size water proof motor having following specifications. P U M P DISCHARGE ( 30.00 M3/H) H E A D (55 mtr.) S H A F T. Stainless Steel. OUTLET SIZE. 80mm. PUMP EFFICIENCY IN PERCENTAGE: Minimum 65. M O T O R (10 HP) Submersible type, 3ph.50Hz, A.C.- 400Volt +10%, wet type winding, RPM-2900. SIZE OF TUBEWELL : (200mm. x 150mm.dia). and length of Housing pipe 39.84mtr. Pump motor set must be BEE standard energy star rating (3-5) as per IS – 8034:2002 Make-KSB/PLUGA/B.G./TEXMO/ Approved Make). N.B.;- (I) H/Q Characteristic Curve of pump set should be submitted before delivery. (II) Test certificate of pump & motor should be submitted during delivery & G.C.

b) 4.0 sq.mm.3core, water proof flat cable, suitable for above pump set. (Make-FINOLEX /GLOSTER /MESCAB /CURRENCY/Crystal /Polycab/ Approved Make)

c) 100 A 4 way 415 V wall mounted Busbar Chamber (make (Havels/Standard/Approved Make)

d) 100 A TPN Main Switch with re-wirable fuse link within sheet steel enclosure(make (Havels/Standard/Approved Make)

e) 100 A , 4 pole , 415 V , TPN , OFF load Change Over Switch ( Make -standard/ Havells/ ABB/ Siemens)

f) Supply and Delivery of 25 mm², 1.1 KV grade. 3.5 core Al Armoured XLPE conform to IS 1554/7098(part-I) 1998 (Make : Gloster /HAVELLS /MESCAB/ CURRENCY/POLYCAB/ CRYSTAL/ Approved Make)

Supply & delivery of following materials of best quality. a) 80mm. N.B. U.P.V.C. column pipe 7.1mm. thick having 70mm. long 8TPI threaded both side with heavy type socket & O ring biax technology with wiring lock system non corrosive high tensile having I.S.O. 9001 standard. (Make : Ashirbad/Raksha/ Approved Make).

i) 10ft. long (3mtrs)

ii) 5ft. long (1.5mtrs)

iii) 80mm. dia. top & bottom adaptor

iv) 3 " dia. X 5 ft long M.S. (7.1 mm Thick) Column pipe having both side 11 TPI Thread and Socket.

b) Heavy type M.S. Suspension clamp of suitable dia. made of 80mm×10mm M.S. flat with nuts, bolts, washer etc.( suitable for 80mm. dia. column pipe)

c) Split type M.S. fabricated tube well cover for 300mm dia. tube well housing pipe with necessary fitting arrangement along with of column pipe, Air pipe, rope of anti snapping device & cable entry gland etc.

d) 102 mm. dia. 0-7 Kg./sq.cm. range, wall mounted pressure gauge. (Make: H. Guru/Febig/ Approved Make).

i) Tube well outside the pump house. (This cost includes 15mm. dia. G.I. pipe Tata medium of appx. 30ft. length & specials)

e) Depth gauge (Make: H. Guru/Febig/ Approved Make) of 102mm. dia. with steel Air pipe of reqd. length (85ft) with all others fittings & accessories for the above work including supplying in one good quality hand pump. i) Tube well outside the pump house.(This cost includes 15mm. dia. G.I pipe of appx. 30ft length & Specials)

f) Anti snapping safety device made of suitable size & heavy type M.S. fabricated busket for resting the above pump set, with eye bolt/H. bolt 25.mm.dia. arrangement (4 ends), clamps for holding pump motor, Nuts & bolts etc. complete as per direction EIC. including 10mm.dia. stranded steel wire rope or 16mm dia. Nylone rope for hanging of anti snapping safety device as per direction of EIC.

g) 80mm.dia. CIDF Non Rising Spindle Sluice Valve (IS: 14846) with PN1.0 Pressure Rating as per I.S. specification & other required materials for the job i.e for completing the construction of delivery and wash out line.(Make:- IVI / UPADHYA / KIRLOSKAR/Durga/ Jupiter/MAGNET/CAIR/McWANE/Sigma Flow/ Approved Make). N.B: I) Test certificates for both valves should be submitted at the time of delivery. II) M. S. Specials should have minimum 7mm.Thickness.

h) Ø80 mm CIDF single door swing Non Return Valve (IS: 5312, Part-I) with PN1.0 Pressure Rating, (Make:-IVI / UPADHYA / KIRLOSKAR/Durga/ Jupiter/MAGNET/CAIR/McWANE/Sigma Flow/ Approved Make).

i) 80mm dia. Three phase, (415V), Actuator operated Wafer type Butterfly Valve (BS: 5155) with PN1.0 Pressure Rating, having valve body of CI(IS: 210, Gr. FG: 260). & shaft of stainless steel (AISI- 410). (Make- Actuator- ROTORK/ CAIR/ Limitorque/Auma Valve – IVI / UPADHYA / KIRLOSKAR/Durga/ Jupiter/MAGNET/CAIR/McWANE/Sigma Flow/ Approved Make). (T.C. Needed).

j) Ø3 " X 2.75 mtr CIDF Pipe

k) Ø3 " X 1.0 mtr CIDF Pipe

l) Ø 3 " X 2'-6" CIDF Pipe

m) Ø 3 " X 2 ft CIDF Pipe

n) Ø 3 "Flanged tail piece

o) Ø 3"CIDF Bend

p)Steel Plug, M. S. Nipple, Flange, Nuts, Bolts etc

q) Ø 3 "M. S. Cross

b) Metallic Over load Relay of Range 1.5 to 3.0 Amp for Chlorinator. c) Level Controller Circuit for Chlorine Tank. III. Yard Lighting Arrangement. a) 9 Amp, TP, 240Volt A.C. Coil Contactor. -1no. b) Programmable Digital Timer for Auto/Manual operation. Note : The following 3 items ( a, b & c) are common for above I,II & III a) ON/OFF/ Trip Indicating Lamp for Pump Motor/Valve Actuator/Chlorinator. – 1set. b) Start/Stop, Forwarded/Reverse Push Button for Manual operation of Pump Motor, Actuator & Chlorinator. c) Power Terminals for Pump Motor/TPN Yard Lighting/ Chlorine Motor along with Level Controller/SPN internal wiring/Valve Actuator -1set. (Make: RNR/ECS/PCF Project/Jolly Engineering Pvt. Ltd./Approved Make)

Making Brick Pillar for Supporting pipe line (10" X 10 " X 4 ft) by 1st class brick work with 4 :1 plaster and net cement punning complete including earth cutting, supplying necessary materials , ramming as per direction of EIC.

Installation of the item no. (1) to (3) with necessary connection complete including supply 12core 1.5sq.mm. copper control cable compensating MS flange nut and Bolts Gasket & other fixing materials to complete the job and making platform of required size around T.W. with bricks, cement , sand stone chips etc(4:2:1) including plastering and net cement complete as per direction and entire satisfaction of the E.I.C.

Supplying & fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of 25Sq.mm. XLPE Armoured cables

Finishing the end of 25Sq.mm. 31/2 core XLPE Armoured cables by crimping method including supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials with including proper sealing of cable entry point

Making necessary non metalic pipe IS-14930 (80mm. dia.) protection for submersible cable from Tube well cover to inside of the pump house including supplying pipe, Elbow, Union, short piece, socket etc. complete for the job as per direction.

Double eathing with 50mm. dia. TATA – Medium G.I. pipe 3.64mm. thick × 3.04Mtr. long and 2×4SWG GI (Hot Dip) wire (4Mtr. long), 13mm. dia. × 80mm. long GI bolts, double nuts, double washers including supply & fitting 15mm. dia. G.I. pipe protection (1Mtrs. Long) to be filled with bitumen partly under the ground level and partly above ground level driven to an overage depth of 3.65Mtrs. below the ground level & restoring surface duly rammed.

Supply, delivery and storage at site of automatically controlled diaphragm type chlorinator dosing pump with flow rate 100 LPH and maximum pressure of 10Kg/CM2 with all accessories for pump & motor, foundation bolt, suction and discharge Flange and with storage tank of dosing solution of 100Ltr. Capacity and the prime mover to be coupled with pump of 0.5 H.P. 3 Phase, 1450 RPM squirrel cage TEFC induciton motor, Motor will be IE2/IE3 (Make of Machine : Swelore/Any other approved, Make of Motor : ABB / CGL /KEC / Any other approved make)

Installtion and commissioning of above supplied chlorinator with all accessories, PVC tank and drawing of power line as per IE rules by supplying of necessary wire and continuous earthing. This include the cost of all necessary CC foundation [at least 200mm height] with concrete mixture [sand, cement, stone chips] and neat cement finish by supplyig of all required materials and testing the entire set as per direction of EIC [power will be feed from PLC Panel of pumping machinery]

Distribution wiring in 1.1KV. Grade, (2X1.5mm2) single core stranded 'FR' PVC insulated & unsheathed copper wire (approved make) in suitable size PVC casing capping (Precision make) with (1.5 Sqmm) single core stranded 'FR' PVC insulted & unsheathed copper wire for ECC, including necessary PVC clips, fittings etc. to light/fan point with piano key type switch (anchor make) fixed on sheet steel fabricated switch board with Perspex/bakelite top cover on wall including necessary connections and making earthing attachment and mending good damages to building works. [PVC casing-capping and Switch board both on surface]

a) average run 4. 5 mtr. -

Supply and fitting fixing of 40A DP Isolator (Make : Havells/Standard/ approved make)

Supply and delivery of CFL , 23 watt, (Make-phillips/ other approved make)

Supply and fitting fixing of Ceiling fan (Make: Usha /Crompton/Havels/ other approved make) 1200mm. sweep complete with blade, rubber bush etc. including supply and fixing 2×1/1.4 PVC copper wire for down rod with making necessary connection complete.

Supply & fitting fixing of 10 watt, LED Fixture set ----------for Phillips Model no. BRP 020/10 LED (Make: Phillps/ Other Approved Make) with 40mm. dia. × 2.5mtr. long G.I pipe bracket fixing on wall of the Pump House with 3nos. M. S. clamp properly grouting including making power connection with supply and drawing 2.5sq.mm. copper flexible cable wire with controlling sub switch and continuous earthing from nearest junction board all complete as per direction of E.I.C.

Supply of 4ft. 36W Double Fluorescent light fittings complete with all accessories including 2nos. 36W tube light incl. fixing light fitting on wall by means L clamp, nipple, suitable size fastner and connection by 1.5 sqmm PVC/Cu wire as to G S. Model :- TMC0552XTLD36WEBT ( Make- Philips/Havells/Bajaj/ other approved make)

Supply and fixing bulkhead light fittings on wall incl. connection. As to Gs .Make -Bajaj/Havells/ other approved make)

Supply and delivery at site A.C. 3 ph. Dry type Voltage Stabilizer suitable for unbalanced input voltage (Make: AE/Sen & Pandit / Opto Elec. / ECS/Fizi/other Approved Make) a) Input:250-500 V 3ph. 50HZ, 4 wire b) Output, 415V + 1% 3ph.,50HZ. c) Capacity: 20 KVA. d) Auto manual switch IS - 9815 (I). e) Raise/lower push Button. f) Single lamps to indicate and limits of input. g) Voltmeter for input and output Voltage. (Manufacturing test certificate should be produced at the time of delivery) h) With U/V.O./V.O./L protection with contractor at output side, input MCB & Ammeter etc. ( TC /GC Needed )

Installation of the above Voltage stabiliser of above (item No.-19, 1.4, 1.5 ) on the foundation incl. Interconnection complete & testing the voltage stabiliser along with other electrical equipments to ensure performance of the equipments in running satisfactorily as per IE Rules & as per direction of E.I.C. incl. testing commissioning complete.

Add. GST@12%

Add. Cess@1%

M.S. ENTERPRISE

DEY ENTERPRISE

S. G. TECHNICAL SERVICES