Improvements to the Kodathur to Kaikilapet road branching from RC-4 Valudavour road in Mannadipet Commune, Puducherry.

Amount

Construction of granular sub-base by providing close graded material, mixing in a mechanical mix plant at OMC, carriage of mixed material to work site, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 of MoRTH specification, 4th Revision - by plant mix method - for grading II material.

Providing,laying , spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layer by manual means in sub-base / base course on well prepared surface and compacting with smooth 3 wheeled steel roller to achieve the desired density.

Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means. (As per MoRTH specification, 4th Revision)

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg. per sqm. on the prepared bituminous / granular surface cleaned with mechanical broom. (As per MoRTH specification, 4th Revision)

Providing and laying bituminous macadam with hot mix plant of capacity not less than 40 -60 TPH using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 507.7 of MoRTH specification, 4th Revision, to achieve the desired compaction. - using grade II metal and bitumen 60/70 grade.

Providing and laying bituminous concrete with HMP of capacity not less than 40 to 60 TPH using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per clause 509 of MoRTH specification, 4th Revision, complete in all respects - Using grade-II material.-Bitumen 60/70

Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes.

Providing and fixing 3m make reflective road studs of category 'A' raised pavement markers made out of poly carbonate/ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values conforming to ASTM D4280. The reflective raised pavement makers shall also confirm the length, height and width of the body shall be less than 100mm, 15mm and 90mm and base of marker shall be flat within 1.3mm (3m equivalent). The marker shall support a load of 13635Kg tested in accordance with ASTM D4280. Lenses shall be moulded of polycarbonate or methyl methecrylate conforming ASTM D788. The area of each retro reflectory surface shall not be less than 13.0 sq.cm. The slope or retro reflectory surface shall be 35+5 degree to base. Each reflector shall have a CIL not less values specified in table 1 of said MORTH circular and two cylindrical polymer shanks not less than 20mm diameter and not less than 30mm length shall be provided for better anchorage with bituminous grout or epoxy mortar.

Providing and fixing of retro - reflectorised cautionary, mandatory & informatory sign as per IRC:67 made of aluminium sheet encapsulated lens with high intensity grade sheeting vide Clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm X 75 mm X 6 mm ( 3.5 mtrs height - 6.8kg/mtr = 23.8kg , with board support angle 35x35x6mm-2.30 mtrs - 3kg/mtr = 6.9kg and anchor flat - 0.5kg)firmly fixed to the ground by means of properly designed foundation with M15 Grade cement concrete 45 cm X 45 cm X 60 cm , 60cm below ground level as per approved drawing. - 60 cm equilateral triangle . (including cost of angle iron towards cost of drilling holes, nuts , bolts etc.,)

Providing and fixing of retro - reflectorised cautionary, mandatory & informatory sign as per IRC:67 made ofaluminium sheet encapsulated lens with high intensity grade sheeting vide Clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm X 75 mm X 6 mm ( 3.8 mtrs height - 6.8kg/mtr = 25.84 kg with board support angle 35x35x6mm - 2.8 mtrs - 3kg/mtr = 8.4kg and anchor flats - 0.5kg ) firmly fixed to the ground by means of properly designed foundation with M15 Grade cement concrete 45 cm X 45 cm X 60 cm, 60cm below ground level as per approved drawing. -80cm X 60cm rectangular . (including cost of angle iron towards cost of drilling holes, nuts, bolts etc.,)

Earth work in excavation by mechanical means (Hydraulic excavation) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10sqm on plan) including getting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m - all kinds of soil

Cement concrete 1:4:8 mix with stone aggregate 40mm nominal size in foundation upto a depth of 1.5 metres below ground level and upto height of 1.5 above ground/bed level.

Centring and shuttering including strutting, propping etc. and removal of form work for - retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

Providing, hoisting and fixing upto plinth level for precast reinforced cement concrete slabs for drain cover slabs of length varying upto 1.50m of various thickness including the cost of required centering, shuttering and finishing smooth with 6mm thick cement plaster 1:3 (1 cement: 3 fine sand) on all faces except bottom of slabs but excluding cost of reinforcement with 1:1.5:3 (1 Cement: 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size).

Steel reinforcement for R.C.C. Works including bending, binding and placing in position - Thermo Mechanical Treated Bars (ISI brand approved make) Fe - 415 or more

Plain cement concrete m-15 mix with stone aggregates 20mm nominal size mechanically mixed and vibrated in foundation upto a depth of 1.50 metres below ground level and/or 1.50 metres above ground/bed level.

MKM Constructions

K ARUNAGIRI & SONS

Kumaresan Constructions