PROVISIONING OF FURNITURE FOR OFFRS JCOS OR MD ACCN OF NCC GP HQ BERHAMPUR UNDER GE I GOS

Amount

Almirah Large Steel 1/2Hx1/2S (FD/E6/MAP/18) (a) Overall size of Almirah large 1/2 Hx1/2 Sh steel shall bel 1900mmx 910mmx 490mm. (b) Almirah's body, shutter, drawer, locker, vertical partitions and shelves shall be made out of 20 Guage MS plain black sheet all as shown in drg. (c) Back shall be of 22 Guage plain black sheet. (d) Welding process shall be of MIG (Metal Inert Gas) type using Carbon dioxide and Argon blend.(e) All MS members shall be pre-treated with epoxy polyester powder coating (Black) 70 microns by 7 tank process and Oven Dried internally & externally with the following specifications. (i) Dry Film thickness more than 45 microns. (ii) Salt Spray test to with stand more than 1000Hours. (iii) Adhesion as per DIN 53152 standards. (iv) Pencil scratch hardness more than 2H (f) Rest all as per drg.

Almirha Med steel 1/2H x 1/2S (FD - 1032) (a) Overall size of Almirah shall be 1270mmx765mmx440mm having three shelves and four compartments. b) Top, doors, shelves and base and legs shall be made up of MS Sheet of imm thick(nominal). c) Handle shall be 100mm long Chromium plated. d) Four lever Lock shall be provided of Grade Il quality conforming to IS 729/1979 alongwith duplicate keys. (e) All MS members shall be pre-treated with epoxy polyester powder coating (Black) 70 microns by 7 tank process and Oven Dried internally & externally with the following specifications. (i) Dry Film thickness more than 45 microns. (ii) Salt Spray test to with stand more than 1000Hours. (iii) Adhesion as per DIN 53152 standards. (iv) Pencil scratch hardness more than 2H. (d) Welding process shall be of MIG(Metal Inert Gas) type using Carbon dioxide and Argon blend. (e) All MS surface shall be spray painted with two coats of synthetic enameled colour to be approved by GE over a coat of red oxide primer

Bath stool PVC (FD/E6/MAP/07) The verall size of the bath stool PVC shall be 400mm L x 300mm W x 250mm H.The bath stool PVC shall be made up of 5mm thick PPCP m,aterial. The bath stool PVC shall have centre leg of dia 25mm. The four leg shall be in arc shape and of size 100mm x 100mm. The top of the bath stool shall have 3mm x 10mm thick stiffner molded along with the seat in single pieace underneath. The weight of the bath stool shall not be less than 1.3 Kgs. Make AMKO/Cello Brite.

Bed hard steel Offrs (FD/E6/MAP/08 (.R)) All as shown on drg and specification Conduit pipe shall be 38mm sq 1.6mm thick for main frame and 19mm sq 1.6mm thick for inner frame for head and foot board 65mmx25mm 1.6mm thick for long rail. 25mm sq 1.6mm thick for stiffener under 12mm plywood shall be used Prelaminated particle board 18mm exterior grade for head and foot board with PVC edging 1mm thick. Finish : All steel surface shall be black powder coating Rest all as shown on drg.

Bin linen Multipurpose (FD/E6/MAP/09) The over all size of the bin linen multipurpose is 1200mm long X 450mm wide X 750mm High. It shall be made of BWR ply of grade-A of thikness as specification in drg in liu of prelaminated particle board. 1mm thick laminated sheet shall be pasted on all exterior surface with marine grade adhesive including 6mm thick teak wood beading shall be provided alround the edges of shutters and drawers. Each drawers shall be provided with 2x Nos of 12 inch long stainless steel telescopic channels. Irrespective of what is shown on drg, the base on bin linen multipurpose shall be of size 1200mm longx 450mm wide x 75mm high, made of 1st class teak wood scantling 30mm thick. The bottom frame shall have four nos of 25mmx25mm stiffernes placed and fitted at equidistant positions inside the base frame. All wood to be used shall be 1st class hard teak wood. The base frame shall be fixed with 85mm long screw fitted from the bottom.Drawer and shutter shall be provided with 100mm long 8mm dia chrome plated handles. Shutter to be provided with magnetic catchers at inside.Rest all specifications and dimensions as per drg.

Chair dining with cushion (FD/E6/MAP/10 R) Overall size shall be 450mm wide x 450 mm deep and 950 mm hight, 450 mm high up to seat. (a) All wood to be used shall be 1 st class hard teak wood. (b) The seat of chair shall bhe made of 40 density foam cushion having thickness 75mm, the cushion shall be placed and pasted on 12 mm BWR plywood as poer size of seat duly covered with approvd tapestry cloth of rate nbot less than 450 per mtr. The seat shall be fixed over the rail and screwed from wood stopper with 30 mm long screws. (c) PVC hard rubber ring of dai 25 mm shall be provided to bottom of each leg with 20mm long screws. Rest all specifications and dimensions are as per drg. Finish: The chair shall be polished in high gloss melamine polish in walnut shade after preparation of surface complated all as specified and directed.

Chair varandha PVC (FD/MAP-II/06) (a) 19 mm MS tube of 16G thick shall be used for frame work. (b) Welding process shall be of MIG (Metal Inert Gas) type using Carbon dioxide and Argon Blend. Joints of welded portion shall be finished smooth. (c) Finish: All MS members shall be Pre-treated with epoxy polyester power coating (Black) 70 microns by 7 tank process and Oven Dried with the following specifications: (i) Dry film thickness more than 45 microns. (ii) Salt Spray test to with stand more than 1000 hours (iii) Adhesion as per DIN 53152 standards. (iv) Pencil scratch hardness more than 2H. (d) 4mm thick seat & back shall be made out of PVC moulded alongwith 4x10mm ribs provided at all around the outer edge & around the grooves of size. (e) Hard PVC inner shoes shall be provided for the legs duly affixed with adhesive. (f) Rest all as per drg or as specified

Chair writing steel (FD/E6/MAP/12) The overall size of the chair shall not be less than 475mm wide and deep and 580mm high at seat from ground level. The seat and back are to be made up of 1.2cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded melamine foam. The back foam is to be designed with contoured lumbar support for extra comfort. The foam is to be moded with density =45+/-2 kg/m3 and Hardness= 20+/-2 at 25% compression. Arm rest shall be one piece. All metel parts shall be dry powder coated in thickness more than 50 microns.

Chair computer revolving (TP) Chair computer revolving with cushion on seat & net on the back with adjustable arms, back support, gas lift, tilt mechnisam, P.U. base. Model No ESC/EX/94. Made Royal Koas or equivalent Godrej interio motion high back or equivalent nature Make durian.

Charpoy IP hard Top (FD/E6/MAP-II/01) Specification: Overall size shall be 1980mm long, 900mm wide and 440mm high. a) The frame of charpoy shall be made of MS hollow section piupe of 16 gauge as per specified sizes mentioned in Drg. b) Top of charpoy shall be of 12mm thick BWR ply of grade-A; Place and fix over the and fix over the stiffeners and cleat with 12 Nos of flat head bolt of 6mm dia, 50mm long nylon insert nut and round washer. c) Each leg of charpoy shall be provided with 32mm x32mm x 5mm thick MS plate shall be welded at bottom of each leg. Rest all specification and dimensions are as per drg The charpoy shall be dry powder coated in black after preparation of surface.

Charpoy Folding IP with hard top (FD-388 (.R)) All as shown on drawing. Overall size shall be of 1980x900x550mm.The frame work shall be 25mm dia 16 guage MS conduit pipe.04 nos stiffner shall be provided between long rail 25mm dia 16 guage .Top shall be of 8mm thick BWR plywood conforming to IS-303. Rest all as shown on drawing. All joints/weldings/fixing shall be done in accordance with standard workmanship. All frame work shall be painted with spray paint synthetic enameled over a coat of primer all as directed by Engg-in -charge.

Hat stand with Mirror (FD – 233) (a) Overall size of the Hat Stand with mirror shall be 1000mmx71 Omm. (b) 4 mm thick one side teak finish ply shall be provided with teak wood edging 4mm thick all around. (c) 3.5mm thick BWR grade plywood conforming to IS:303 of Make KitpIy/Archidply/Century shall be provided on back side. d) Pegs shall be of copper oxidized steel pegs. (e) 5mm thick mirror shall be provided of Make Atul, /Goldfish/Swastik/Kohinoor. (f) All wooden portion shall be French polished till attaining glossy finish. g) Rest all as per drg and as specified.

Ladder Aluminium (FD – 1025) (a) The overall length & width shall be 2310x363.5mm. (b) Aliminium stringers as shown in drawings of size 1.75x60mmx3.18mm thick channel bent shape as shown in drg. (c) 08 rungs each of 23 mm dia& 2.43 mm equally spaced, leaving 100mm on either side of stringer. The rungs shall be closed with hard rubber caps on either side. (d) Aluminum anodised shall be of 15 micron. (e) Hard rubber cap/shoe made out of 32x60x80mm, shall be provided on either ends of the stringer as shown on drawings. (e) Rest all as per drg or as specified.

Table Peg (FD – 384) (a) All wood work shall be first class hard wood season teak. (b) Irrespective of whatever is showin in the drg top shall be 18/19mm thick prelaminated particle board exterior grade OSD lamination of teak finish shade and other white balancing lamination as specified here-in-before ISI marked.c) All exposed surface shall be French polished in golden colour. (d) 4mm teak wood edging for table top shall be provided as shown on drg. (e) Hard PCV toe shall be provided on each legs. (f) All joints fixing shall be done in accordance width the standard work manship and specification. (g) Rest all as per drg or directed by Engineer-in-Charge.

Receptical PVC (FD/E6/MAP/13) All as shown on drawing. Overall size Receptical shall be of capacity 20 ltr . The body of receptical PVC shall be made up of thick polymet plastic of thickness not less than 2.5mm provided with swivel lid and iron handles on both sides as shown in drg. Make Cello, TUPPERWARE or AMKO equivalent as shown in drg.

Shoe rack steel (FD/E6/MAP/02 (.R)) Overall size shall be 700mm long, 300mm wide and 880mm hig. The legs of the shoe rack shall be of 25mm dia MS pipe of 18 gauge. The five shelves of the rack shall be of 20mm dia MS pipe of 18 gauge welded to legs . The shelves shall have 3mm dia Ms rod 9 Nos in widthwise and 3 Nos in lengthwise welded to 20mm dia shelf frame. All steel surface shall be black powder coating Rest all as shown on drg.

Side Board (FD – 241) (a) The overall size of the side board shall be 1220x455x760mm. (b) Top, sides, shutters and bottom shall be of 18mm thick pre-laminated particle Board, Ext grade l/Type Il conforming to IS: 12823 along with 4mm thick teakwood edging to be provided (c) Four Drawers shall be provided at equal spaces. (d) Powder quoted MS handle 02 Nos of size 100mm long to be provided to two doors each. (e) Two catch spring shall be provided to the shutters. (f) 75mm high skirting shall be provided of 19mm thick teakwood. (g) All exposed wooden surfaces shall be French polished to attain glossy finish. (h) Rest all as per drg & all as specified.

Sofa set 5 seater with cushion (FD/MAP/II/02) Overall size of three seater shall be 1730mm wide, 725mm deep and 530mm high up to arm level and one seater shall be 670mm wide and 725mm dee and 530mm high up to arm. All wood to be used shall be 1st class hard teak Wood. Soda set five seater shall consist of one three seater and two single seats. 10xNos of foam cushion to each set each of size 530m,mx560mmx100mm thick of 40 density coverd with white lining cloth and best quality tapestry cloth of rate not less than 450 per mtr shall be provided with nylon zipper at one edge duly covered under the tapestry cloth flap. PVC hard rubber shoes of 25mm dia shall be provided to bottom of each leg with 20mm long screws.All wooden surface shall be polished with high gloss melamine polish in walnut shade after preparation of surface. Rest all specification and dimensions are as per drg.

Table bed side (MAP) (FD/E6/MAP/15 (.R)) All as per drg and specification tlimber 1st class hard wood teak Plywood 12mm for side back and drawer and 6mm plywood for bottom of drawer and back side. Legs shall be 18Sqmm condult pipe 1.6mm thick black powder coated paint 18/19mm pre laminated particle board of exterior grade IS-12823 beaded with PVC beading. All exposed partion shall be polished with french polish in high gloss finish. Rest all as per drg.

Table dining 6 Per's (FD/MAP-11/03) (a) The overall size of the table shall be 1500x900x760mm. The table top shall be of 18mm thick pre-laminated Particle board exterior grade conforming IS-12823=1990 to Grade I Exterior quality & type-Il (PLMDF-12 Designation) as per IS:14587:1998 (Reaffirmed 2003). (c) All woodwork shall be be of 1st class teakwood of specie Tectona Grandis conforming to IS-1331:1971 free from dead knots and moisture content as permissible as per IS-287. (d) 6mm thick TW lipping shall be provided on all the exposed edges of MDF Duly treated with French polish as specified. (f) Powder coated MS angular plates each of 150mmx30mmx5mm thick shall be screwed to the legs at right angles with long rails and short rails. (g) Hard nylon shoes/buffers shall be provided to each leg bottom.

Table center (FD – 274) (a) The overall size of the table shall be of 900x450x400mm. (b) Table Top shall be 18mm thick pre-laminated particle board, phenol bonded with phenol formaldehyde,exterior Grade BWR Gde, pre-laminated one side with teak finish and matching white on other, conforming to IS: 12823 and ISI marked. Edges shall be provided with 6mm thick teakwood beading. (c) PVC rings to be screwed of appropriate size to be provided to all the four legs of the chair. (d) All exposed timber surfaces shall be french polished to obtain glossy finish. (e) Rest all as per drg & all as specified.

Table writing (FD – 275) (a) The overall size of the table shall be 1150x600x760mm. (b) The table top and cabinet below drawer shall be of 18mm thick pre-laminated Particle board exterior grade conforming IS-12823=1990 to Grade I Exterior quality & type-Il (PLMDF-12 Designation) as per IS:14587:1998 (Reaffirmed 2003). (c) The sides & back of drawers shall be 12mm thick plain MDF board, conforming to Gde-l(SBG-l) in terms of IS-124062003 irrespective to whatever shown on drg. (d)The Plain/Prelaminated MDF board shall conform to the specific requirements given for ECO-MARK under relavant clauses of the std. (e) All woodwork shall be be of 1st class teakwood of specie Tectona Grandis conforming to IS-1331 : 1971 free from dead knots and moisture content as permissible as per IS-287. (f) 6mm thick TW lipping shall be provided on all the exposed edges of MDF Duly treated with French polish as specified. (g) Powder coated MS angular plates each of 150mmx30mmx5mm thick shall be screwed to the legs at right angles with long rails and short rails. (h) Hard nylon shoes/buffers shall be provided to each leg bottom. (j) The drawers shall be fitted on 1.6mm thick powder quoted telescopic channels with proper packing if required•

Table dressing ladise with stool (FD/MAP-II/07) The overall size of the table dressing shall be 1150mm long 380mm wide and 1700mm high and Overall size of the stool shall be 440mm wide. It shall be made up of BWR plywood of grade-A of specified thickness as per drg in lieu of prelaminated particle board.1mm thick laminated sheet shall be pasted on all exterior surface with marine garde adhesive including 6mm thick teak wood beading shall be provided alround the edges of shutters and drawers. Drawers shall be provided with 2x Nos of inch long stainless steel telescopic channels.Drawer and shutter shall be provided with 90mm long recessed metal handles and shutter to be provieded with magnetic catches. Looking mirror shall be 5mm thick electro copper plated fixed over 6mm thick plywood back. 4x Nos heavy duty double wheel castors shall be provided at bass ply. The seat of the stool shall be 75mm thick, 40 density foam cushion covered with best quality tapestry cloth of rate not less than 450 per mtr rest all specification and dimesions are as per drg

Table computer (FD/E6/MAP/03) (a) Overall size of Table computer shall be 900x561.2x750mm. (b) The whole table top, drawer etc shall be made up of 18mm thick prelaminated Particle Board, BWR, Exterior Grade, conformng 10 IS: 12823. (c) The frame work shall be made of 25mmx25mmx16guage thick CRCA box section and supported on 25x50mm x16guage thick CRCA box section duly covered with PVC cover. (d) The drawers and key board shall be fitted on .6mm thick powder quoted telescopic channels. (e) Foot screws shall be provided to the base of the unit for adjustment of 50mm height.

Teapoy (FD – 382) (a) The overall size of the table shall be 600x450x540mm. (b) The table top shall be of 18mm thick pre-laminated Particle board exterior grade conforming IS-12823=1990 to Grade I Exterior quality & type-Il (PLMDF-12 Designation) as per IS: 14587: 1998 (Reaffirmed 2003). (c)The Prelaminated MDF board shall conform to the specific requirements given for ECO-MARK under relavant clauses of the std. (d) All woodwork shall be be of 1st class teakwood of specie Tectona Grandis conforming to IS-1331:1971 free from dead knots and moisture content as permissible as per IS-287 (e) PVC hard rubber shoe shall be provided for each leg. (f) Rest all as per drg & as specified.

Teapoy varandha (FD/E6/MAP/17) (a) The overall size of the teapoy verandah shall be 750mmx450mmmx540mm. b) Table Top shall be 18mm thick pre-laminated particle board, exterior Grade pre-laminated one side with teak finish and matching white on other, conformjng to IS: 12823 and ISI marked. Edges shall be provided with 4mm thick teakwood beading, c) The main frame work for Rails. legs, stiffeners & base shall be of 18mmx18mmx18guage CRCA box section. d)The void of base tray frame shall be filled by weld 5mm MS bars, 10 Nos in length —wise and 12 in widthwise. e)All CRCA/MS members shall be pre•treated with e poxy polyster powder coating (Black) 70 microns by 7 tank process and Oven Dried internally & externally With the following specifications. (O) Dry Film thickness more than 45 microns. (n) Salt Spray test to with stand more than 1000Hours. (iii) Adhesion as per DIN 53152 standards, (iv) Pencil scratch hardness moro than 2H. (f) Rest all as per drg or as specified

TV Trolly (FD/E6/MAP/04 (R)) (a) The Overall size of the Trolly shall be 750x600x750mm. (b) The table top and cabinet below drawer shall be of 18mm thick pre-laminated Particle board exterior grade conforming IS-12823=1990 to Grade I Exterior quality & type-Il (PLMDF-12 Designation) as per (Reaffirmed 2003) (c) The Plain/Prelaminated MDF board shall conform to the specific requirements given for ECO-MARK under relavant clauses of the std. (d) 5.5mm thick glass shutter shall be fitted with SS hinges & magnet catcher. (e) The whole unit shall be supported on 50mm dia PVC heavy duty twin caster wheels of approved make (f) Decorative handles shall be of brass & 100mm long. (g) The Shutter shall be fitted with continious piano hinges and magnet catcher. (h) Rest all as per drg & as specified.

Table dressing Gents with Mirror (FD/.E6/MAP/16) Overall size shall be 1200mm high, 600mm wide and 100mm high. All wood to be used shall be 1st calss hard teak wood. It shall be made up of BWR plywood of grade-A of specified thikness as per drg in lieu of prelaminated particle board. 1mm thick laminated sheet be pasted on all exterior surface with marine grade adhesive including 6mm thik teak wood beading shall be provided alround the edges of shutters and drawers. Looking mirror shall be 5mm thick fixed inside the teak wood frame made out of 38mmx25mm section. 03x glass shelves of 5mm thickness shall be fixed inside the box with glass holders as shown in drg. Rest all specification and dimensions are as per drg. Preparation of surfaces shall be polish in high gloss melamine polish.

Book case steel (FD – 1028) All as shown on drawing. Overall size shall be 840 mm long, 310 mm wide and 1675 mm high. All sheet shall be mild steel 1 mm thick, back, sides, bottom top and shelves shall be 1 mm thick. The book case shall be provided with four compartments of equal size. The shutters of each compartment shall open towards top and slide in to the depth of the book case. Two steel handles 100 mm long shall be provided to each shutter of the compartment. The locking device shall be provided to each compartment. All steel surfaces exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of surfaces. All joints fixing shall be done in accordance with standard workmanship and specifications. Rest all as shown on drawing.

Chair dining PVC (FD/E6/MAP/03) All woodwork shall be of 1st class teakwood of special Tectona Grandis conforming to IS-1331:1971 free from knots and cracks shall be used with moisture content permissible as per IS:287:1973. The seat shall be PVC 4mm thick visible like Godrej pattern with 4x10mm thick ribs moulded alongwith seat in single piece screwed with seat frame as shown in drawing. Nylon buffers of appropriate size to bew provided to all the four legs of the chair. All exposed wooden surface shall be smootherned before applying french polish till it attains glossy finish. All joints fixing shall be fixed with bamboo pins and nails shall not be used. Rest all as per drgs or as specified.

Table dining 4 Per's (FD/MAP-ll/03) (a) The overall size of the table shall be 1200x900x760mm. (b) The table top shall be of 18mm thick pre-laminated Particle board exterior grade conforming IS-12823=1990 to Grade I Exterior quality & type-Il (PLMDF-12 Designation) as per IS:14587:1998 (Reaffirmed 2003). (c) All woodwork shall be be of 1st class teakwood of specie Tectona Grandis conforming to IS-1331:1971 free from dead knots and moisture content as permissible as per IS-287. (d) 6mm thick TW lipping shall be provided on all the exposed edges of MDF Duly treated with French polish as specified. (f) Powder coated MS angular plates each of 150mmx30mmx5mm thick shall be screwed to the legs at right angles with long rails and short rails. (g) Hard nylon shoes/buffers shall be provided to each leg bottom. (h) Rest all as per drg & as specified.

Table 3' x 2' with drawer wooden (FD – 283) (a) The overall size of the table shall be 900x600x760mm. (b) The table top shall be of 18mm thick pre-laminated Particle board exterior grade conforming IS-12823=1990 to Grade I Exterior quality & type-Il (PLMDF-12 Designation) as per (Reaffirmed 2003). (c) The front portion of drawers shall be 18mm thick pre-laminated Particle board, onforming to Gde-l Type Il (PLMDF-12-l) in terms of IS-14587:1998 (Reaffirmed-2003). (d) The sides & back of drawers shall be 12mm thick plain MDF board, conforming to Gde-l(SBG-l) in terms of IS-12406-2003 irrespective to whatever shown on drg. (d)The Plain/Prelaminated MDF board shall conform to the specific requirements given for ECO-MARK under relavant clauses of the std. (e) All woodwork shall be be of 1st class teakwood of specie Tectona Grandis conforming to IS-1331:1971 free from dead knots and moisture content as permissible as per IS-287. (f) Powder coated MS angular plates each of 150mmx30mmx5mm thick shall be screwed to the legs at right angles with long rails and short rails. (g) PVC hard rubber shoe shall be provided for each leg. (h) The drawers shall be fitted on 1.6mm thick powder quoted telescopic channels with proper packing if required. (j) Rest all as per drg & as specified.

Chair school with hard board (FD/E6/MAP/105) (a) The frame work for side supports seat support at front and rear side and support frame for top shall be 25mm dia CRCA pipe of 16 Guage thick. (b) The single piece PVC seat and back shall be one piece of weight not less than 1.20 kg, of Blowplast or equivalent Make. (c) One shelf shall be provided between the side frames below the seat made up of 4mm dia MS plain bars as shown. (d) All CRCA members shall be shall be pre-treated with epoxy polyester powder coating (Black) 70 microns by 7 tank process and Oven Dned internally & externally with the following specifications (i) Dry Film thickness more than 45 microns. (ii) Salt Spray test to With stand more than 1000Hours. (iii) Adhesion as per DIN 53152 standards. (iv) Pencil scratch hardness more than 2H. (e) Welding process shall be of MIG(Metal Inert Gas) type using Carbon dioxide and Argon blend. (f) The openable top shall be of 18mm thick prelaminated particle board of exterior grade conforming to IS: 12823, duly fitted to slide on the right frame. The edges of top shall be finished with 1.5mm thick PVC beeaing with wire nails. (g) Rest all as per drg or as directed.

Chair Easy (FD – 229) Dimension : Overall size shall be 510mm long, 575mm wide and 720mm high. Description : a) All wood to be used shall be 1st class hard teak wood. (b) PVC hard rubber ring of dia 25mm shall be provided to bottam of each leg with 20mm long screws. c) Caning shall be done in true godrej pattern with virgin plastic cane of 2mm wide, 0.6mm thick half round gola type weighting not less than 6 gms in ten running meters with border woven with 4mm thick cane. Rest all specification and dimensions are as per drg. FINISH: The chair shall be polished in high glass melamine polish in walnut shade after preparation of surface.

Chair Writing (FD – 280) All woodwork shall be of 1st class teakwood of specie Tectona Grandis conforming to IS-1331:1971 free from dead knots and moisture content as permissinle as per IS-287. Canning of the chairs shall be of Godrej pattern with 2mm and 3.5mm approved qulity of plastic cane and holes to be covered by 3.5mm wide cane. The canning used for seat has high tensile strength as specified IS:5378 Part II/1990, Cane breaking strength=3000kg/mm2(min) % Elongation at break =25%. TW triangular brackets of size 60x60x25mm thick both ends chamfered shall be screwed on the legs/side rails joint below seat for both rear and front legs ie 4 bracket per chair. PVC rings to be screwed of appropriate size to be provided to all the four legs of the chair.All exposed surfaces shall be french polished.

PRADIPTA KUMAR PANI

M/S T.N.CONSTRUCTION