Special repair maintenance work of school building in PM Shri Kendriya Vidyalaya, Basti, UP-272002

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300

mm or more (thickness to be specified by the manufacturer), of 1st

quality conforming to IS : 15622, of approved make, in all colours

11.38 shade,except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick sqm 435.50 1279.79 557,347.19

cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey

cement slurry @ 3.3kg/ sqm including grouting the joints with white

cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles

conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except

burgundy, bottle green, black of any size as approved by

8.31 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 SQM 314.44 1267.95 398,694.20

mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand)

and jointing with grey cement slurry @ 3.3kg per sqm, including

pointing in white cement mixed with pigment of matching shade

Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of required dia & length

(hold fast lugs or dash fastener shall be paid for separately)

9.1.1 Second class teak wood cum 3 142949.7 428,849.10

Providing and fixing ISI marked flush door shutters conforming to

IS : 2202 (Part I) non-decorative type, core of block board

9.21 construction with frame of 1st class hard wood and well matched

commercial 3 ply veneering with vertical grains or cross bands

and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws

Providing and fixing aluminium tower bolts, ISI marked, anodised

(anodi ccoating not less than grade AC 10 as per IS : 1868 )

transparent or dyed to required colour or shade, with necessary

screws etc. complete :

Providing and fixing ISI marked oxidised M.S. handles conforming

9.66 to IS:4992 with necessary screws etc. complete (Copper oxidised

as per IS 1378)

Digitally signed by AMIT

Providing and fixing bright finished brass 100 mm mortice latch

9.76 and lock with 6 levers and a pair of lever handles of approved each 32 854.65 27,348.80

quality with necessary screws etc. complete.

Providing and fixing 150 mm bright finished floor brass door

14.34 stopper with rubber cushion, necessary brass screws etc. to suit each 32 271.45 8,686.40

shutter thickness complete

Providing and fixing aluminium die cast body tubular type

hydraulic door closer (having brand logo with ISI, IS : 3564,

on the body, door weight upto 35 kg and door width upto 700

necessary accessories and screws etc. complete.

UPVC Windows : Supply and Fixing of Tripple Track/ Tripple Channel

UPVC Windows, DGU/ Sandvich Glasses (6 mm Reflective Glass + 10

MR-1 mm Air Gap + 6 mm Plain Toughned Glass) on two tracks and SS Mesh SQM 15 10,526.00 157,890.00

on One Track, complete as per the requirement of engineer in charge.

Providing and fixing 18 mm thick gang saw cut, mirror

polished,premoulded and prepolished, machine cut for

kitchen platforms, vanity counters, window sills, facias and

similar locations of required size, approved shade, colour

8.2 and texture laid over 20 mm thick base cement mortar 1:4

(1 cement : 4 coarse sand), joints treated with white

cement, mixed with matching pigment, epoxy touch ups,

including rubbing, curing,moulding and polishing of edges to

give high gloss finish etc. complete at all levels.

8.2.2 Granite stone slab of colour black, Cherry/Ruby red

8.2.2.2 Area of slab over 0.50 sqm sqm 250 5136.3 1284075

Repairs to plaster of thickness 12 mm to 20 mm in patches

of area 2.5 sq.meters and under, including cutting the patch

in proper shape, raking out joints and preparing and

plastering the surface of the walls complete, including

disposal of rubbish to the dumping ground, all complete as

per direction of Engineer-in-Charge.

14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand) Sqm 350 561.727495 196605

Providing and applying white cement based putty of average

thickness 1 mm, of approved brand and manufacturer, over

the plastered wall surface to prepare the surface even and

smooth complete.

Distempering with 1st quality acrylic distemper (ready

13.81 mixed) having VOC (Volatile Organic Compound ) content

less than 50 gram/ litre, of approved brand and

13.81.1 Old work (one or more coats) SQM 3000 62.7 188100

Finishing walls with Acrylic Smooth exterior paint of required

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on

existing cement paint surface

Providing and laying integral cement based water proofing

treatment including preparation of surface as required for

treatment of roofs, balconies, terraces etc consisting of

following operations:

Digitally signed by AMIT

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm

of cement admixed with water proofing compound

conforming to IS. 2645 and approved by Engineer-in-charge

over the RCC slab including adjoining walls upto 300 mm

height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick

bats 25 mm to 115 mm size with 50% of cement mortar 1:5

(1 cement : 5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by

Engineerin- charge over 20 mm thick layer of cement

mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with

water proofing compound conforming to IS : 2645 and

approved by Engineerin- charge to required slope and

treating similarly the adjoining walls upto 300 mm height

including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of

cement slurry using 2.75 kg/ sqm of cement admixed with

water proofing compound conforming to IS : 2645 and

approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement

With average thickness of 120 mm and minimum thickness

at khurra as 65 mm.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm)

with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial

emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20

mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand)

and grouting the joints with mix of white cement & marble powder in ratio

of 1:1, including rubbing and polishing of the surface upto 3 cuts complete,

including providing skirting upto 150 mm height along the parapet walls in

the same manner.

13.4 12 mm cement plaster of mix :

Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in foundation and plinth in:

6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) Cum 60 7370.65 442239

Providing and fixing concertina coil fencing with punched

tape concertina coil 600 mm dia 10 metre openable length (

total length 90 m), having 50 nos rounds per 6 metre

length, upto 3 m height of wall with existing angle iron ‘Y’

shaped placed 2.4m or 3.00 m apart and with 9 horizontal

R.B.T. reinforced barbed wire, stud tied with G.I. staples

16.53 and G.I. clips to retain horizontal, including necessary bolts meter 5500 375.8 2066900

or G.I. barbed wire tied to angle iron,all complete as per

direction of Engineer-in-charge, with reinforced barbed

tape(R.B.T.) / Spring core (2.5 mm thick) wire of high

tensile strength of 165 kg/ sq. mm with tape (0.52 mm

thick) and weight 43.478 gm/ metre (cost of M.S. angle,

C.C. blocks shall be paid separately)

Structural steel work riveted, bolted or welded in built up

sections, trusses and framed work, including cutting,

hoisting, fixing in position and applying a priming coat of

approved steel primer all complete.

Digitally signed by AMIT

Providing and fixing multiwall solid/structured polycarbonate

sheets of 16 mm thickness, UV-stabilized,

clear/translucent/coloured as specified, including cutting to

MR-2 size, drilling, necessary aluminium/gi/GI powder-coated sqm 200.00 2,500.00 500,000.00

profiles, EPDM rubber gaskets, sealant, fasteners, and all

accessories required for complete installation as per

drawings and manufacturer’s specifications.

Painting with synthetic enamel paint of approved brand and

manufacture to give an even shade :

13.61.1 Two or more coats on new work sqm 1,000.00 155.9 155,900.00

Digitally signed by AMIT

Electrical Estimate

S.No. DSR Ref. No. DESCRIPTION UNIT QTY DSR RATE DSR AMOUNT MARKET RATE MR AMOUNT

Wiring for light point/ fan point/exhaust fan point/call bell point with 1.5

sq. mm FRLS PVC insulated copper conductor single core cable in

surface/recessed medium class PVC conduit, with modular switch,

1.10 modular plate, suitable GI box and earthing the point with 1.5 sq. mm.

FRLS PVC insulated copper conductor single core cable etc as required.

1.10.3 Group-C (Primary point ) Point 200 1,704.00 340,800.00

Wiring for group controlled (looped) light point/ fan point/call

bell point (without independent switch etc.) with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in

surface / recessed PVC conduit, and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core cable etc as

Wiring for twin control light point with 1.5 sq.mm

FRLS/HFFR PVC insulated copper conductor single

core cable in surface / recessed steel conduit, 2 way

1.4 modular switch, modular plate, suitable GI box and Point 20 2,242.00 44,840.00

earthing the point with 1.5 sq.mm. FRLS/HFFR PVC

insulated copper conductor single core cable etc .as

Wiring for light/ power plug with 2X4 sq. mm

FRLS/HFFR PVC insulated copper conductor single

1.12 core cable in surface/ recessed medium class PVC m 2000 373.00 746,000.00

conduit along with 1 No. 4 sq. mm FRLS/HFFR PVC

insulated copper conductor single core cable for loop

earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with

1.14 the following sizes of FR PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 1200 373.00 447,600.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 200 482.00 96,400.00

1.14.5 2 X 10 sq. mm + 1 X 6 sq. mm earth wire Metre 200 621.00 124,200.00

1.14.6 2 X 16 sq. mm + 1 X 6 sq. mm earth wire Metre 200 832.00 166,400.00

Supplying and drawing following pair 0.5 mm dia

1.18 FRLS/HFFR PVC insulated annealed copper

conductor, unarmored telephone cable in the existing

surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade,

0.7 mm solid copper conductor PE insulated, shielded

1.19 with fine tinned copper braid and protected with PVC m 300 54.00 16,200.00

sheath in the existing surface/ recessed steel/ PVC

conduit as required.

Supplying and fixing of following sizes of steel conduit

along with accessories in surface/recess including

1.20 painting in case of surface conduit, or cutting the wall

and making good the same in case of recessed

conduit as required.

Digitally signed by AMIT

Supplying and fixing of following sizes of medium class PVC

1.21 conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of

recessed conduit as required.

Supplying and fixing metal box of following sizes (nominal

size) on surface or in recess with suitable size of phenolic

laminated sheet cover in front including painting etc. as

Supplying and fixing following modular switch/ socket

1.24 on the existing modular plate & switch box including

connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 150 136.00 20,400.00

1.24.5 6 pin 15/16 amp socket outlet Each 150 219.00 32,850.00

1.24.6 Telephone socket outlet Each 30 168.00 5,040.00

1.24.7 TV antenna socket outlet Each 30 168.00 5,040.00

Supplying and fixing two module stepped type electronic fan regulator

1.25 on the existing modular plate switch box including connections but Each 40 402.00 16,080.00

excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular

plate & switch box excluding modular plate as required

Supplying and fixing following size/ modules, GI box along with modular

base & cover plate for modular switches in recess etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover

in front on surface or in recess, including providing and fixing 3 pin 5/6

A modular socket outlet and 5/6 A modular switch, connections etc. as

Supplying and fixing suitable size GI box with modular plate and cover

in front on surface or in recess, including providing and fixing 6 pin 5/6

& 15/16 A modular socket outlet and 15/16 A modular switch,

connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/

wooden block including connections etc. as required.

Supplying and fixing brass batten/ angle holder including connection

etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V,

complete as required.

Digitally signed by AMIT

Installation, Testing and Commissioning of ceiling fan,including wiring

the down rods of standard length (upto 30 cm) with 1.5 sq. mm

1.45 FRLS/HFFR PVC insulated, copper conductor, single core cable, including Each 100 332.00 33,200.00

providing and fixing phenolic laminated sheet cover on the fan box etc.

Installation, Testing and Commissioning of exhaust fan in the existing

1.50 opening, including making good the damage, connection, testing,

commissioning etc. as required.

Extra for fixing the louvers/ shutters complete with frame for a exhaust

fan of all sizes.

Providing and fixing following capacity TP&N disconnector fuse switch

2.1 unit inside the existing panelboard with ISI marked HRC fuses including

drilling holes in cubicle panel, making connections, etc. as required.

Providing and fixing following rating and breaking capacity and pole

MCCB with thermomagneticrelease and terminal spreaders in existing

2.2 cubicle panel board including drilling holes in cubicle panel, making

connections, Ics=100% Icu and Operational Voltage 690V etc. as

Supplying and fixing following way, single pole and neutral, sheet steel,

MCB distribution board, 240 V, on surface/ recess, complete with tinned

2.3 copper bus bar, neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing of following ways surface/ recess mounting,

vertical type, 415 V, TPN MCB distribution board of sheet steel, dust

protected, duly powder painted, inclusive of 200 A tinned copper bus

2.5 bar, common neutral link, earth bar, din bar for mounting MCBs (but

without MCBs and incomer ) as required . (Note : Vertical type MCB

TPDB is normally used where 3 phase outlets are required.)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

2.1 the existing MCB

DB complete with connections, testing and commissioning etc. as

2.10.2 Single pole and neutral each 20 643.00 12,860.00

2.10.5 Triple pole and neutral each 10 1,301.00 13,010.00

Supplying and fixing single pole blanking plate in the

existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240

V, isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as

Digitally signed by AMIT

Supplying and fixing following rating, four pole, (three phase and

neutral), 415 volts, residual current circuit breaker (RCCB), having a

sensitivity current 30 mA in the existing MCB DB complete with

2.15 connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200

mm X 150 mm, made of mild steel, at least 2 mm

2.21 thick, and vitreous enamelled white on both sides, each 10 315.00 3,150.00

and with inscription in single red colour on front side

Supplying and installaton following size of perforated painted with

powder coating M.S. cable trays withperforation not more than 17.5%,

in convenient sections, joined with connectors, suspended from the

ceiling with two numbers MS/GI Suspenders i/c base of suitable size

MS/GI angle, bolts & nuts, painting suspenders, fastener etc as

4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness Metre 100 623.00 62,300.00

4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness Metre 80 686.00 54,880.00

4.1.3 200 mm width X 50 mm depth X 1.6 mm thickness Metre 100 775.00 77,500.00

4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Metre 80 866.00 69,280.00

Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including

accessories, and providing masonry enclosure with cover plate having

locking arrangement and watering pipe etc. with charcoal/ coke and salt

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe of 2.7 Meter long etc.

with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick

including accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe of 2.7 Meter long etc.

with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below

ground as strip earth electrode, including connection/ terminating with

5.9 G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by Metre 200 160.00 32,000.00

overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe

5.11 from earth electrode includingconnection with G.I. nut, bolt, spring, Metre 100 755.00 75,500.00

washer excavation and re-filling etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop

5.18 earthing along with existing surface/ recessed conduit/ submain wiring/ Metre 200 50.00 10,000.00

cable as required.

Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface

of wall for lightning conductor complete as required.(For horizontal run)

Laying of one number PVC insulated and PVC sheathed / XLPE power

cable of 1.1 KV grade of following size direct in ground including

excavation, sand cushioning, protective covering and refilling the trench

etc as required.

10.1.2 Above 35 sq. mm and upto 95 sq. mm Metre 900 475.00 427,500.00

Supplying and making end termination with brass compression gland

and aluminium lugs for following size of PVC insulated and PVC

sheathed / XLPE aluminium conductor cable of 1.1 KV grade as

Digitally signed by AMIT

Providing, laying and fixing following dia RCC pipe NP2 class (light duty)

in ground complete with RCC collars, jointing with cement mortar 1:2 (1

cement : 2 fine sand) including trenching (75 cm deep) and refilling etc

Supply, Installation, Testing and Commissioning of ceiling fan with

Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos.

metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies,

shackle kit, safety rope, copper winding, steel/Al body Power Factor not

less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM

(tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less

9.2 than 10%, suitable for operation with regulator for speed control and all

remaining accessories

including safety pin, nut bolts, washers, temperature rise=75 0C

(max.), insulation resistance more than 2 mega ohm, suitable for 230

V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019

fan i/c external connections with 1.5 sq.mm FRLS/HFFR,PVC insulated

copper conductor single core cable and earthing etc. as required.

1400mm, service value ≥ 6.0 CM/Min/Watt, air delivery 245 CM/Min

1.1KV grade multicore aluminium conductor XLPE insulated and PVC

sheathed armoured cable conforming to relevant IS. (Cable shall be

purchased only after approval of cable schedule by architect /

consultant) of following sizes

Flange mounted hot dip Galvanized Octangonal Pole of 7 Mtr height

made from 3.5 mm thick HT Steel plate, having top dia-90mm & bottom

dia of 155 mm complete with window with flash cover at a height of

500mm from the base for cable termination block etc and galvanized

base plate of size 220 mm x 220mm x 12 mm thick on existing cement

concrete pedestal as required including supplying and fixing the

following in the window box provided for cable termination as per

direction of engineer incharge:-

a) Supplying and fixing 6mm thick laminated mounted sheet inside the

window mounted on and including providing and welding 02 nos G.I.

strips 4mm thick of suitable length and having suitable size tapped

b) Supplying and fixing 63 Amps terminal block, suitable for 10 sq.mm

conductor- 04 nos & shorting links- 05 nos. on DIN Channel including

providing. And fixing DIN Channel of suitable length- 01 nos on the

MR-2 existing laminated sheet. each 25 14,530.00 363,250.00

c) Supplying and fixing 6 Amps, SPMCB, “C” characteristics curve- 02

nos, Earth stud 02 nos, welded at suitable height, washers, springs

washers & nuts.

d) M - 20 reinforced cement concrete foundation of size 550mm x

550mm wide and 1200 mm deep i/c excavation of earth, providing

cutting, bending and placing in position, reinforcement of cold twisted

bars of 12 mm dia- 1200 mm long (approx)- 08 nos and reinforcement

ring of cold twisted bar of 8 mm dia-190 spacing centre to centre

(approx)- as required with positioning of foundation bolts as shown in

the item given below and providing 63 mm (O.D.) PVC Pipe of suitable

length for cable entry & exit as required.

e) 04 nos, M20X470mm j-type (EN8grade) foundation bolt (total length

600mm) with nuts, washer including 01 nos template of 3 mm thick size

220x220mm with 4 nos 24mm dia holes, to match with PCD of pole

base plate as reqd.

f) 1 meter long Galvanized single arm bracket for mounting on pole and

Digitally signed by AMIT

LED Street light fixture, powder coated pressure die cast aluminium

body (System lumen efficacy >135 lm/Watt).

Supplying, Installation, Testing & Commissioning

8.14 of Street light LED fixture, powder coated

pressure die cast aluminium body with built in or

separate driver as per the requirement with Driver

efficiency >85%, Input voltage: 140-270 Volt AC,

20 watt 50/60 hz, Operating temp range -5 0C to 25

Supplying, installation, Testing & Commissioning of

LED Recessed/surface Down lighter (Round/

square/ Rectangular) SMD type of following body

material with PMMA and prismatic diffuser and

8.2 construction as per IS : 10322 with driver as per

the requirement with Driver efficiency >85%,

Operating voltage AC 140-270 Volt, frequency

50/60 hz, Operating temp range -5 0C to 40 0C

centigrade, internal surge protection of 2.5 KV

with Short & Open circuit protection ,THD < 10%,

LED Batten light (System lumen efficacy ≥105 <120

Supplying, Installation, Testing & Commissioning of LED surface

mounted Batten light of following bodymaterial and construction

as per IS : 10322 with driver (Replaceable) as per the

requirement with Driver efficiency >85%, Operating voltage AC

140- 270 Volt, frequency 50/60 hz, Operating temp range -5 °C

8.9 to 40 °C, internal surge protection of 2.5 KV with Short & Open

circuit protection, THD < 10%, P.F.≥0.95, IP20, CRI >80, Flicker

free, (flicker should be below 5 %), life time (LED, Driver &

electricalcircuitry), of minimum 50000 Burning Hours with 70% of

initial Lumen maintained till life ends, CCT 3000°K / 4000°K /

5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation

Colour Matching) <3, Maximum power consumption should not

more than the specified rating and Fixture shall be of relevant BIS

8.9.1 standard.

18- Manufactures Word Mark/ Name Engraved/ Embossing/

Supplying, drawing, Testing and commissioning of Cat6A

UTP 4 pair, 23 AWG solid copper cable in existing conduit/

on surface, U/FTP, LSZH, NonPlenum, Horizontal (solid)

Cable suitable for high speed data networking application

supporting upto 10Gbps over a 100 meter channel. The 4

Unshielded Twisted Pairs (UTP) cable with color coded

39.18 insulation for easy indentification should have

FLAMEPROPERTIES i.e. Flammability Test - IEC 60332-1,

Smoke Density - IEC 61034, LSZH standards compliance:

ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS.

Delay Skew should be < 45NS. The outer Cable Diameter

should be 7.5 + 2 mm. Cable should have been tested and

verified by UL/ ETL etc.

complete as required.

39.18.1 1 Run of cable meter 100 74 7400

Supplying of Single Phase Copper Digital Motors 450mm BLDC

Exhaust fan, 1400 RPM with necessary screws etc.

LT PANEL (Normal-Raw power)

Digitally signed by AMIT

1 Nos 160 Amp FP Moulded Case Circuit Breaker

1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.

1 No.160 Amp digital ammeter with inbuilt selector switch and CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

MR-4 1 Set of Electronic KWH Meter.

200 Amp TPN aluminium busbar.

04 No. 63 Amp TPN Miniature Circuit Breaker (MCB)

03 No. 40 Amp TPN Miniature Circuit Breaker (MCB)

01 No of control / power wiring.

Panel described as above LS 1 230,000.00 230000

METER BOARD (TYPE-A&B)

1 Nos 250 Amp FP Moulded Case Circuit Breaker

1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.

1 No. 200 Amp digital ammeter with inbuilt selector switch and CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

1 Set of Electronic KWH Meter.

300 Amp TPN aluminium bus bar.

03 Nos 63 Amp TPN Miniature Circuit Breaker.

12 Nos 40 Amp TPN Miniature Circuit Breaker with Electronic Energy Meter.

2 Nos 40 Amp TPN Miniature Circuit Breaker

1 No of control / power wiring.

Panel described as above LS 1 330,000.00 330000

EXTERNAL LIGHTING PANEL-

Cubicle type totally enclosed free standing type moisture, dust, vermin & weather proof Floor Distribution Panel

made out of 2.0 mm thick & front cover 1.6 mm thick CRCA sheet complete with following equipments,

including digital ammeter with inbuilt ammeter selector switch, digital voltmeter with inbuilt voltmeter

selector switch, indicating lamps, CT's, internal wiring with suitable size wires / cable, interconnection,

painting complete as per specification & drawing.

1 No. 100 Amp FP ( 35 KA Ics) Moulded Case Circuit Breaker.

1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.

1 No. 100 Amp digital ammeter with inbuilt selector switch and CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

1 Set 24 Hrs TSQ Timer

1 Set 100 Amp, 4P Contactor & A/M switch and Push Button.

100 Amp TPN aluminium busbar.

09 No. 25 Amp DP MCB.

03 No. 63 Amp TPN MCB.

Panel described as above LS 1 115,000.00 115000

Digitally signed by AMIT

Plumbing/ Sanitary Estimate

S.No. DSR Ref. No. DESCRIPTION UNIT QTY DSR RATE DSR AMOUNT MARKET RATE MR AMOUNT

Providing and fixing floor mounted, white vitreous china single

piece, double traps syphonic water closet of approved

brand/make, shape, size and pattern including integrated white

vitreous china cistern of capacity 10 litre with dual flushing

17.81 system, including all fittings and fixtures with seat cover, cistern each 12 18212.9 218554.8

fittings, nuts, bolts and gasket etc including making connection

with the existing P/S trap, complete in all respect as per

directions of Engineer-in-Charge.

Supply, Installation, Testing and Commisiong of PNEUMATIC

SINGLE PIECE SLIM CONCEALED CISTERN BODY WITH

INSTALLATION KIT & “S-TYPE” DRAIN PIPE CONNECTION SET

FOR WALL HUNG WC (WITHOUT FLUSH CONTROL PLATE)

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP

Brass single hole basin mixer of approved quality and make,

17.7A including painting of fittings and brackets, cutting and making

good the walls wherever required:

White Vitreous China Wash basin size 550x400 mm with a 15

A mm CP Brass single hole basin mixer each 42 3960.55 166343.1

Providing and fixing white vitreous china flat back or wall corner

type lipped front urinal basin of 430x260x350 mm and

340x410x265 mm sizes respectively with automatic flushing

17.4.1 cistern with standard flush pipe and C.P. brass spreaders with

brass unions and G.I clamps complete, including painting of

fittings and brackets, cutting and making good the walls and

floors wherever required :

One urinal basin with 5 litre white P.V.C. automatic flushing

Providing and fixing water closet squatting pan (Indian type W.C.

pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level

white P.V.C. flushing cistern, including flush pipe, with manually

17.1 controlled device (handle lever) conforming to IS : 7231, with all

fittings and fixtures complete, including cutting and making good

the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440

mm with integral type foot rests

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube

upto 1 metre long with S.S. triangular plate to Eureopean type

17.16A W.C. of quality and make as approved by Engineer - in - charge each 12 349.15 0.00

Providing and fixing C.P. brass angle valve for basin mixer

18.53 and gyser points of approved quality conforming to IS :

18.53.1 15 mm nominal bore each 100 574.3 57430

Providing and fixing C.P. brass long body bib cock of approved

18.51.1 quality conforming to IS standards and weighing not less than 690 EACH 50.00 777.38 38,868.92

gms. 15 mm nominal bore

Digitally signed by AMIT

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 38 mm single piece moulded with height of 270

mm, effective length of tail pipe 260 mm from the centre of

17.70.2 the waste coupling, 77 mm breadth with 25 mm minimum each 50 375.65 18782.5

water seal, weighing not less than 263 gms

Providing and fixing PTMT grating of approved quality and

18.58.1 Circular type

18.58.1.1 125 mm nominal dia with 25 mm waste hole each 50 51.85 2592.5

Providing and fixing mirror of superior glass (of approved quality) and

17.32 of required shape and size with plastic moulded frame of approved

make and shade with 6 mm thick hard board backing :

17.32.4 Rectangular shape 1500x450 mm nos 10 2093 20930

Providing and fixing PTMT pillar cock of approved quality and colour.

15 mm nominal bore, 107 mm long, weighing not less than 110 gms

Providing and fixing PTMT Waste Coupling for wash basin

17.69 and sink, of approved quality and colour.

Waste coupling 38 mm dia of 83 mm length and 77 mm

breadth, weighing not less than 60 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, havingthermal stability for hot & cold water supply

and all CPVC plain & brass threaded fittings, including fixing

18.7 the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent

cement and testing of joints complete as per direction of

Engineer in Charge

18.7.3 25 mm nominal dia Pipes metre 120 401.55 48186

18.7.5 40 mm nominal dia Pipes metre 110 702.95 77324.5

18.7.6 50 mm nominal dia Pipes metre 100 934.15 93415

Digitally signed by AMIT

Miscellaneous Work- Kendriya Vidyalaya, Basti,UP

TRACK ROAD WORKS

Breif Description of works MARKET

S.no DSR.NO. Unit Qty DSR RATE DSR AMOUNT MR AMOUNT

Earth work by mechinical / manual means in rough excavation, banking

excavated earth in layers not exceeding 20cm in depth, breaking clods,

watering, rolling each layer with ½ tonne roller or wooden or steel

rammers, and rolling every 3rd and top-most layer with power roller of

minimum 8 tonnes and dressing up in embankments for roads, flood

banks, marginal banks and guide banks or filling up ground depressions,

lead upto 50 m and for all lif

Preparation and consolidation of sub grade with power road roller of 8 to

12 tonne capacity after excavating earth to an average of 22.5 cm depth,

dressing to camber and consolidating with road roller including making

2.00 16.1 good the undulations etc. and re-rolling the sub grade and disposal of CUM 480.00 218.90 105072.00

surplus earthwith lead upto 50 metres.

2.0 Sub-Base :

Construction of granular sub-base by providing close graded Material

conforming to specifications, mixing in a mechanical mix plant at OMC, carriage

3.00 16.78 of mixed material by tippers to work site, for all leads & lifts, spreading in

uniform layers of specified thickness with motor grader on prepared surface and

compacting with vibratory power roller to achieve the desired density, complete

as per specifica ons and direc ons of Engineer in-Charge.

With material conforming to Grade-I (size range 75 mm to 0.075 mm) having

3.0 Water Bound Macadam :

Cutting road and making good the same including supply of extra quantities of

materials i.e. aggregate, moorum screening, red bajri and labour required

16.13 Water bound macadam Cum. 210.00 3078.05

4.0 Concrete work :

Digitally signed by AMIT

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40

mm nominal size) in pavements, laid to required slope and camber in panels as

required including consolidation finishing and tamping complete

5.0 Shuttering work :

Centering and shuttering including strutting, propping etc. and removal

6.00 5.9 of form for

Foundations, footings, bases of columns, etc. for mass concrete Sqm 240.00 392.15 94116.00

6.0 Road Furnitures / Sign Boards / LED Traffic Signals :

Manufacturing, supplying and fixing retro reflective sign boards made up of 2

7.00 16.59 mm thick aluminium sheet, face to be fully covered with high intensity

encapsulated type heat activated retro reflective sheeting conforming to type - IV

of ASTM-D 4956-01

Mandatory/ in blue

Regulatory sign and silver

boards whitemm

of 900 or other colour

diametre withcombination

support length of 3750 mm

Cautionary /warning sign boards of equilateral triangular

16.59 shape having each side of 900 mm with support length of each 4.00 5559.75 22239.00

Supplying, Installation, Testing & Commissioning of Traffic Signal Systems

consisting of : One

8.00 MR A.) job

LED traffic signals(15nos),Signal blinkers(10nos),Traffic signal controller

(1nos),Traffic signal body (25 nos), with IP 65 , 300 mm dia , 6 mts MS pole

7.0 Road Marking :

Providing and applying 2.5 mm thick road marking strips (retro- reflective)

9.00 16.62 of specified shade/ colour using hot thermoplastic material by fully/ semi Sqm 180.00 747.80 134604.00

automatic thermoplastic paint applicator machine fitted with profile shoe,

Workdispenser, propane tank heater and profile shoe heater,

Earth work in excavation by mechanical means (Hydraulic excavator)/

10.00 2.6 manual means over areas (exceeding 30 cm in depth, 1.5 m in width as Cum 428.400 177.550 76062.42

well as 10 sqm on plan) including getting out and disposal of excavated

9 In front of Stage

Filling available excavated earth (excluding rock) in trenches, plinth, sides

11.00 2.25 of foundations etc. in layers not exceeding 20cm in depth, consolidating Cum 142.800 196.000 27988.80

each deposited layer by ramming and watering, lead up to 50 and for all lift

10 In front of Stage

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from

12.00 4.1.3 natural sources : 4 graded stone aggregate 20 mm nominal Cum 148.800 7878.500 1172320.80

size derived from natural sources)

Digitally signed by AMIT

Providing and laying factory made chamfered edge Cement Concrete paver

blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of

required strength, thickness & size/ shape, made by table vibratory method

using PU mould, laid in required colour & pattern over 50 mm thick

compacted bed of sand, compacting and proper embedding/laying of inter

13.00 16.91 locking paver blocks into the sand bedding layer through vibratory

compaction by using plate vibrator, filling the joints with sand and cutting

of paver blocks as per required size and pattern, finishing and sweeping

extra sand. complete all as per direction of Engineer-in-Charge.

60 mm thick cement concrete paver block of M-35 grade with approved

colour, design & pattern.

In front of Stage

Providing and laying at or near ground level factory made kerb stone of

14.00 16.69 M-25 grade cement concrete in position to the required line, level and Cum 36 10117.6 364233.60

curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand),

including making joints with or without grooves (thickness of joints except

Digitally signed by AMIT