AGE I CGN 11 22 23 REPAIR TO BOUNDARY WALL GATES FENCING AT COAST GUARD NOIDA UNDER AGE I CG NOIDA

Amount

Taking down cement plaster on brick or stone walls etc incl raking out joints, hacking for key, scrubbing down with water incl rubbish off the demolished material out of Mod land complete all as specified and directed

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and directed.

Dismantling fencing wire mesh, any type all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion (embedded in concrete, brick work, masonry etc) and making good disturbed ground.

M&L for brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius,built in cement motar 1:6. complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surface with WPC and finished even and smooth without using extra cement complete all as specified and directed. Note: WPC will be paid separately under respective item.

Supply only liquid water proofing compound

M & L for preparing new plastered or unplastered surfaces of wall, priming plastered and other surfaces with alkali resistant priming paint and applying two coats of cement paint complete all as specified and directed.

Complete removal of existing treatment on walls, priming plastered and other surfaces with alkali resistant priming paint and applying two coats of cement paint complete all as specified and directed.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1cement : 4 Coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3Kg of cement per sqm, top layer 15mm cement plaster 1:1/2:2(1 cement : 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern incl scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified. Note: Providing grooves shall be paid seperately.

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer incl removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specification and direction of the Engineer in charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.

S&F Fe 410-W (Gde-E-250) quality-A, for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, nuts, bolts etc. complete all as specified and directed.

S & F in repairs Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed (each line wire to be measured)

S&F in repair punched tape concertina coil (PTTC) 610 mm dia, having 50 turns and madeup of 2.60mm HTGS spring core wire having tensile strength as per revelent IS and punched tape of 0.50mm thick and 13mm wide after criming punched tape shall be hot dipped galvanised min 200 micron & having medium barbs of 24mm width @35mm centre to centre complete all as specified and directed.

S&F MS flat iron fillets (for securing wire mesh etc) to fencing post including all necessary drilling, bolting or riveting etc and similar work conforming to Fe - 290 (Gde- E-165) .

Supply only Chain link MS galvanisd fencing, as directed by Engr-in-charge.

Fixing only chain link fencing incl line wires, any mesh, size and type to any type of standards, rails, straining bolts etc incl provision of binding wire complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to the store and rubbish off the premises of MOD land complete all as specified.

M&L for 20mm thick granite work (table rubbed and polished) in steps, jambs, pillars window cills and like in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust and jointed with Granite epoxy/silicone glue complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations and rubbing and polishing complete all as specified and directed.

M&L for 10mm thick rendering for backing of tiles in CM 1:3 on fair faces of brick work or concrete surfaces.

M&L for Glazed coloured ceramic digital tiles in vertical surface 300x 600mm x 10mm thick in pattern or concept set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles complete all as specified & directed.

S&F RCC Decorative jaali, made out of red sand stone, of overall size 550mm to 600mm x 550mm to 600mm, 35 mm thick with frame of width 75mm to 40mm alround, incl fixed in between pillars in CM 1:2 with an admixture of pigment to match stone jaali colour complete all as specified and directed.

S&F for fine dressed red stone ornamental pillars of design as approved, of overall height of 900mm incl top design, size at middle 75mm x 75mm incl embeded in PCC to suitable distance to fixed stone jaali between two pillars complete all as specified and directed.

Supply and fixing in repairs, 12 mm thick PVC board CNC cutting Jalli incl all fittings as per required size at any floor complete all as specified and as directed.

S & F in repairs 16 to 18mm thick Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with hold fastener ( size M8 SS 304 ) and including one number SS clamps (grade -202) of flat 30mm X 2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for fixing hold fastener, polishing, rubbing & including Laticrete 190 sealer complete all as specified and as directed by Engr- in -Charge.