Construction of New Administrative Building for Maharashtra State Secondary and Higher Secondary Education Board Ratnagiri

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150mm in thickness. (Item No. 2.09)

Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete.(Lift from 1.5 to 3.0m.) By Mechanical Means (Item No. 21.08)

Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/murum watering, ramming etc. complete.(Lift upto 1.5 m). By Mechanical Means (Item No. 21.20)

Providing preconstructional antitermite treatment as per I.S. 6313(Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. (Item No. 21.22)

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/granite/quartzite/gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 24.01)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/granite/quartzite/gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.15)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/granite/quartzite/gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.35)

... (Item No. 25.35, First Floor)

... (Item No. 25.35, Second Floor)

... (Item No. 25.35, Third Floor)

... (Item No. 25.35, Fourth Floor)

Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap/granite/quartzite/gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.19)

... (Item No. 26.19, First Floor)

... (Item No. 26.19, Second Floor)

... (Item No. 26.19, Third Floor)

... (Item No. 26.19, Fourth Floor)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/granite/quartzite/gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.54)

... (Item No. 25.54, First Floor)

... (Item No. 25.54, Second Floor)

... (Item No. 25.54, Third Floor)

... (Item No. 25.54, Fourth Floor)

Providing second class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/in plinth external walls including bailing out water manually, striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete. (Item No. 27.01)

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. Layers including watering and compacting etc. complete. (Item No. 21.36)

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15cm to 20cm including watering and compaction etc. complete. (Item No. 21.37)

Providing preconstructional antitermite treatment as per I.S. 6313(Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper. (Item No. 21.24)

Providing dry/trap/granite/quartzite/gneiss rubble stone soling 15cm to 20cm thick including hand packing and compacting etc. complete. (Item No. 21.38)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/granite/quartzite/gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.74)

... (Item No. 25.74, First Floor)

... (Item No. 25.74, Second Floor)

... (Item No. 25.74, Third Floor)

... (Item No. 25.74, Fourth Floor)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/quartzite/granite/gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete.(Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.26)

... (Item No. 26.26, First Floor)

... (Item No. 26.26, Second Floor)

... (Item No. 26.26, Third Floor)

... (Item No. 26.26, Fourth Floor)

Providing and fixing in position TMT-FE-500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (Item No. 26.33)

Additional for anti corrosive treatment for Providing TMT reinforcement steel of Fe-500D Grade or higher grade conforming to IS1786 (latest) from approved list of supplier, cost of material, royalty, transportation, handling, storing, straightening, cutting, bending, tying, lap/butt welding placing including 18 gauge GI binding wire in diamond form at each reinforcement junction in all structural concrete at all heights and depths with all leads complete as directed. Rate shall also include welding involved toward stray current protection effects as per system approved by Engineer in charge. The rate shall also include the cost of binding wire, labour, all materials, tools and plants, all leads, lifts etc complete as per drawings and technical specification as directed by Engineer-In -Charge.

Providing and laying Cast in situ/Ready Mixcement concrete M-30 of trap/granite/quartzite/gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.07)

... (Item No. 26.07, First Floor)

... (Item No. 26.07, Second Floor)

... (Item No. 26.07, Third Floor)

... (Item No. 26.07, Fourth Floor)

Providing second class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete (Item No. 27.05)

... (Item No. 27.05, First Floor)

... (Item No. 27.05, Second Floor)

... (Item No. 27.05, Third Floor)

... (Item No. 27.05, Fourth Floor)

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185(Part 3)-1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete.(The test shall be carried out conforming to IS:6441(Part I)-1972) (Item No. 27.15)

... (Item No. 27.15, First Floor)

... (Item No. 27.15, Second Floor)

... (Item No. 27.15, Third Floor)

... (Item No. 27.15, Fourth Floor)

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185(Part 3)-1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc. Complete.(The test shall be carried out conforming to IS:6441(Part I)-1972) (Item No. 27.16)

... (Item No. 27.16, First Floor)

... (Item No. 27.16, Second Floor)

... (Item No. 27.16, Third Floor)

... (Item No. 27.16, Fourth Floor)

Providing and fixing Country cut teak wood partly veneered and partly glazed partition with 75mm x 50mm frame at 60cm center and 9mm thick commercial ply on both sides, decorative veneer of 4mm thick and plain glass 5mm thick, including French polishing etc.complete (Item No. 39.70)

... (Item No. 39.70, First Floor)

... (Item No. 39.70, Second Floor)

... (Item No. 39.70, Third Floor)

Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.(Wooden centering will not be allowed.) With fine aggregate(Crushed sand VSI Grade) (Item No. 24.16)

... (Item No. 24.16, First Floor)

... (Item No. 24.16, Second Floor)

... (Item No. 24.16, Third Floor)

... (Item No. 24.16, Fourth Floor)

Providing and fixing chicken mesh of 22 gauge, with about 30cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete/B.B.masonry and or tying by binding wire etc. complete. (Item No. 32.26)

... (Item No. 32.26, First Floor)

... (Item No. 32.26, Second Floor)

... (Item No. 32.26, Third Floor)

... (Item No. 32.26, Fourth Floor)

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness incm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding incm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete. (Item No. 31.26, First Floor)

... (Item No. 31.26, Second Floor)

... (Item No. 31.26, Third Floor)

... (Item No. 31.26, Fourth Floor)

Providing waterproof plaster in W.C. and bath 12mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete.(Excluding Tiles)(As directed by Engineer in Charge) (Item No. 31.06)

... (Item No. 31.06, First Floor)

... (Item No. 31.06, Second Floor)

... (Item No. 31.06, Third Floor)

... (Item No. 31.06, Fourth Floor)

Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5mm thickness in Global white color tile to be laid on grid systems with 15mm wide T-section flanges color white having rotary stitching on the Main Runner, 1200mm and 600mm Cross Tees.Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5mm thickness in Global white color tile to be laid on grid systems with 15mm wide T-section flanges color white having rotary stitching on the Main Runner, 1200mm and 600mm Cross Tees.products approved as per GRIHA and BS 476 etc. complete. (Item No. 38.48)

... (Item No. 38.48, First Floor)

... (Item No. 38.48, Second Floor)

... (Item No. 38.48, Third Floor)

... (Item No. 38.48, Fourth Floor)

Providing and fixing in position Gypsum board false ceiling with 12.5mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete. (Item No. 38.51)

... (Item No. 38.51, First Floor)

... (Item No. 38.51, Second Floor)

... (Item No. 38.51, Third Floor)

Providing and applying gypsum plaster(with Gypsum material) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface/or on newly brick surface(Excluding rough cast plaster) in all position including preparing and Finishing the surface scaffolding etc.complete. (Item No. 32.31)

... (Item No. 32.31, First Floor)

... (Item No. 32.31, Second Floor)

... (Item No. 32.31, Third Floor)

... (Item No. 32.31, Fourth Floor)

Providing and applying gypsum plaster(with Gypsum material) with finishing with gypsum material in 6 millimeter thickness to previously plastered surface(Excluding rough cast plaster) in all position including preparing and Finishing the surface scaffolding etc.complete.

... (First Floor)

... (Second Floor)

... (Third Floor)

... (Fourth Floor)

Providing and applying impression 24 carrat Luxury paint of approved make & approved brand Emulsion paint to interior walls and ceilings of approved quality, colour and shade to new surface in two coats, including sub surface prparation by Acrylic putty and Acrylic primer coats including scaffolding, preparing the surface. etc. complete(Low VOC). (Item No. 48.15)

... (Item No. 48.15, First Floor)

... (Item No. 48.15, Second Floor)

... (Item No. 48.15, Third Floor)

... (Item No. 48.15, Fourth Floor)

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. (Item No. 32.11)

... (Item No. 32.11, First Floor)

... (Item No. 32.11, Second Floor)

... (Item No. 32.11, Third Floor)

... (Item No. 32.11, Fourth Floor)

Providing and laying telephone black/Amba White/Cadburybrown/Ruby red/Ocean Brown granite stone of 18 to 20mm thick for door frame/dado/window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete. (Item No. 33.68)

... (Item No. 33.68, First Floor)

... (Item No. 33.68, Second Floor)

... (Item No. 33.68, Third Floor)

... (Item No. 33.68, Fourth Floor)

Providing 25mm to 30mm thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etc. Fixing in cement mortar 1:3 curing and cement etc. complete. a) One side polish (Item No. 33.32)

... (Item No. 33.32, First Floor)

... (Item No. 33.32, Second Floor)

... (Item No. 33.32, Third Floor)

... (Item No. 33.32, Fourth Floor)

Providing sills of required material 20mm to 25mm thick, on a bed of cement mortar 1:4 including cement float, filling joints with neat cement slurry, curing, moulding edges, polishing, cleaning complete. b) Granite (Item No. 33.22)

... (Item No. 33.22, First Floor)

... (Item No. 33.22, Second Floor)

... (Item No. 33.22, Third Floor)

... (Item No. 33.22, Fourth Floor)

Providing and fixing in position powder coated aluminium louvered windows/ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38mm x 1.22mm box type, 5mm thick sheet glass louvers, of approved quality etc. complete. (Item No. 39.68)

... (Item No. 39.68, First Floor)

... (Item No. 39.68, Second Floor)

... (Item No. 39.68, Third Floor)

... (Item No. 39.68, Fourth Floor)

Providing and fixing in position(as per 1868/1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90mm at weight 0.637 Kilogram/running metre. with window frame bottom track section 92 x 31.75 x 1.30mm at weight 1.070 Kilogram/running metre.. Top and side track section 92 x 31.75 x 1.30mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25mm at weight 0.417 Kilogram/running metre. Inter locking section 40 x 18 x 1.10mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box (Item No. 39.41)

... (Item No. 39.41, Fourth Floor)

Providing and fixing 12mm thick clear toughened glass cladding with supporting frame in aluminium sections with opening wherever required including all necessary fittings, labour, transportation, Scaffolding etc. complete, as directed by engineer in charge.

... (First Floor)

... (Second Floor)

... (Third Floor)

... (Fourth Floor)

Providing and fixing solid core flush door shutter in double leaf 32mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. (Item No. 39.95)

... (Item No. 39.95, First Floor)

... (Item No. 39.95, Second Floor)

... (Item No. 39.95, Third Floor)

... (Item No. 39.95, Fourth Floor)

Providing and fixing 12mm thick toughened glass door shutter with all necessary fittings etc complete.

Providing and fixing frame with/without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete (Item No. 39.01)

... (Item No. 39.01, First Floor)

... (Item No. 39.01, Second Floor)

... (Item No. 39.01, Third Floor)

... (Item No. 39.01, Fourth Floor)

Providing and fixing solid core flush door shutter in single leaf 32mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. (Item No. 39.09)

... (Item No. 39.09, First Floor)

... (Item No. 39.09, Second Floor)

... (Item No. 39.09, Third Floor)

... (Item No. 39.09, Fourth Floor)

Providing and Fixing 30MM thick BOTH SIDE PRELAMINATED SOLID PANEL PVC DOOR SHUTTER consisting of frame made out of M.S tubes of 19 guage thickness and, size 19 x 19mm for styles and 15 x15mm for the top and bottom rails, M.S frame shall have a coat of metel primer of approved make and manufacture. M.S frame shall be covered with heat mouled PVC 'C' channel made from 5mm(+/0.25) thick prelaminated sheet of density 600 Kilogram/cbm, of size 30mm thickness 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45? angle on either side forming stiles and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be falt and 20mm shall be tapered in 45 on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be falt and 20mm shall be tapered on both sides to form lock rail.Top, bottom and lock rail shall be provided either side of the panel. An additional 5mm(+/0.25) thick PVC strip of 20mm width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5mm(+/0.25) thick PVC sheet to be fitted inside the M.S. frame welded/sealed to the styles and rails with 5mm(+/0.25) x 30mm PVC sheet beading on either side and joined together with solvent cement adhesive etc, 10mm thickness(5mm(+/0.25) x 2 nos) 20mm wide cross PVC sheet as gap insert for the rail and bottom rail. Door to be fixed to frames with 3 nos M.S.powder coated but hinges of size 100mm x 25MM x 2mm using 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares (Item No. 39.47)

... (Item No. 39.47, First Floor)

... (Item No. 39.47, Second Floor)

... (Item No. 39.47, Third Floor)

... (Item No. 39.47, Fourth Floor)

Providing and laying in position flooring and skirting of telephone black/Amba White/Cat bary brown/Ruby red/Ocean Brown granite stone of approved shade and size 18mm to 20mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. (Item No. 33.34)

... (Item No. 33.34, First Floor)

... (Item No. 33.34, Second Floor)

... (Item No. 33.34, Third Floor)

... (Item No. 33.34, Fourth Floor)

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete. (Item No. 33.56)

Providing and fixing machine cut mirror polished 18mm to 20mm thick telephone black granite/Amba White/Cat bary brown/RBI red/Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish (Item No. 33.36)

... (Item No. 33.36, First Floor)

... (Item No. 33.36, Second Floor)

... (Item No. 33.36, Third Floor)

Providing and fixing machine cut machine polished 18mm to 20mm thick telephone black/Amba White/Cat bary brown/RBI red/Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. (Item No. 33.35)

... (Item No. 33.35, First Floor)

... (Item No. 33.35, Second Floor)

... (Item No. 33.35, Third Floor)

... (Item No. 33.35, Fourth Floor)

Providing and laying polished hand cut Kotah Stone flooring 25mm to 30mm thick and 45cm to 55cm wide in plain/diamond pattern on a bed of 1:6 C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning complete. (Item No. 33.08)

... (Item No. 33.08, First Floor)

... (Item No. 33.08, Second Floor)

... (Item No. 33.08, Third Floor)

... (Item No. 33.08, Fourth Floor)

Providing and fixing in required position skirting or dado of polished Kotah Stone slab 25mm to 30mm thick fixed on base on plaster of cement mortar 1:4 including cement float, filling joints with cement slurry, curing rubbing, polishing and cleaning complete. (Item No. 33.81)

... (Item No. 33.81, First Floor)

... (Item No. 33.81, Second Floor)

... (Item No. 33.81, Third Floor)

... (Item No. 33.81, Fourth Floor)

Providing and fixing high polished granite stone for wall cladding having stones 25mm to 30mm thick and required width in 1:3 cement mortar including cement float, filling joints with neat cement slurry, curing, cleaning complete.

... (First Floor)

... (Second Floor)

... (Third Floor)

... (Fourth Floor)

Providing and fixing high polished kota stone for wall cladding having stones 25mm to 30mm thick and required width in 1:3 cement mortar including cement float, filling joints with neat cement slurry, curing, cleaning complete.

... (First Floor)

... (Second Floor)

... (Third Floor)

... (Fourth Floor)

Providing and laying vitrified matt fininsh tiles having size 590mm to 605mm x to 605mm of 8 to 10mm thickness and confirming IS. 15622-2006(Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. (Item No. 33.42)

... (Item No. 33.42, First Floor)

... (Item No. 33.42, Second Floor)

... (Item No. 33.42, Third Floor)

... (Item No. 33.42, Fourth Floor)

Providing and laying vitrified matt finish tiles having size 590mm to 605mm x to 605mm of 8 to 10mm thickness and confirming IS. 15622-2006(Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. (Item No. 33.43)

... (Item No. 33.43, First Floor)

... (Item No. 33.43, Second Floor)

... (Item No. 33.43, Third Floor)

... (Item No. 33.43, Fourth Floor)

Providing and applying a base coat comprising of 1KilogramPolydee-MC and 1Kilogramfresh cement after wetting the surface followed by drying the surface for 2 days, apply primer coat of TP-40 and after drying, applying Polydee-11 two component(mixing ratio 2 A : 1 B)) Antibacterial food grade coating inside drinking water tank in two coats with time interval of minimum 8 hrs. covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/-etc. complete. (Item No. 31.11)

Providing cement based water proofing treatment to terraces(Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20mm. thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/-including ponding test etc. complete. (Item No. 31.04)

Providing and applying white-wash in two coats on old/new plastered or masonry surfaces and asbestos cement sheets including scaffolding and preparing the surface by brushing and brooming down etc. complete. (Item No. 36.03)

... (Item No. 36.03, First Floor)

... (Item No. 36.03, Second Floor)

... (Item No. 36.03, Third Floor)

... (Item No. 36.03, Fourth Floor)

Supply and installation of cubicles of width and depth as per Athena Lite-SS Series Cubicles-Std Sizes(W x D x H): 900mm x 1550mm x 2105mm, (Height is including 100mm gap from bottom, Door Width-600mm specifications/site drawings). Cubicle height to be 2105mm. Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120C, All doors will be of single colour and made of 12mm thick Merino HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 stainless steel made hinges affixed to the pilasters. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are H shaped(Top) head frame structure made of extruded Aluminium grade 6063 T5-50 micron epoxy powder coated for surface protection, Size to be 125x70x5T. Corner joinery section, Size to be 40x16.5x1.8T. U-Channel Wall joinery section, Size to be 22x16x1.6T. Door stopper section, Size to be 21x12.5x1.6T. Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacor coated.etc complete. (Item No. 51.162)

... (Item No. 51.162, First Floor)

... (Item No. 51.162, Second Floor)

... (Item No. 51.162, Third Floor)

Providing and applying antipeel paint of approved make & approved brand exterior Emulsion paint of approved quality, colour and shade to old and new surface in two coats, including exterior acrylic primer coat, scaffolding, preparing the surface etc. complete(Heat Reflective Paint). (Item No. 48.16)

... (Item No. 48.16, First Floor)

... (Item No. 48.16, Second Floor)

... (Item No. 48.16, Third Floor)

... (Item No. 48.16, Fourth Floor)

2 Hour Insulated, Flame, Smoke Radiation check Lead Lined Fire Door 57mm 2HR FRL(120/120) 3 Criteria-INTEGRITY/INSULATION/STABILITY WOODEN DOOR-Fire Door Tested in accordance to IS: 3614 Part 2. with prior approval of concerned Superitending Engineer. Providing of 120 min Fire rated lead lined doors system duly tested for 3 criteria-Integrity, Insulation and Stability Criteria as per the IS: 3614 Part 2 and BS: 476 part 22 with standard heating conditions as specified in IS:3614 Part II 1992 and BS: 476 part 20 & 22 1987 to achieve the required integrity, insulation and stability(i.e. to restrict the heat radiation, temperature rise on the non fire side to the maximum of 140 C above the ambient temperature on the exposed surface of the shutter. The fire doors are tested with NCBN technology("Non Combustible by Nature"). Lead lined to check radiation. Code No; 2 Hour Insulated, Flame, Smoke Radiation check Lead Lined Fire Door 57mm 2HR FRL(120/120) 3 Criteria-INTEGRITY/INSULATION/STABILITY WOODEN DOOR-Fire Door Tested in accordance to IS: 3614 Part 2. :: b) Shutter: Providing of 57mm thick asbestos free composite, 'TUFWUD' brand-3 criteria-fire, heat and smoke check Lead Lined Door Shutter with flame guard of 120 minutes IS3614 part-II comprising of 2x9mm Calcium Silicate boards, Chemical treated internal timber with Fire retardant chemicals in pressure impregnation vessels under 160 PSI pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 frame work of 100x30mm with 30mm thick infill of ceramic fibre(density 128 Kilograms/CMT) vermiculite mix, 3mm thick Lead Sheet on one side faced & 3mm Fire retardant High Density Fibreboard, internally lipped with hardwood beading, and pasted in Hydraulic Press under 50 tonnes pressure, spray quoted with 2 coats of Intumescent paint of minimum 300 micron, and with 1 row of Brush-Type Astroflame intumescent strip(imported) of size 10mmx4mm concealed for fire and smoke sealing in the grooves in the shutter on all edges except bottom, without any external lipping. (Item No. 50.83b)

... (Item No. 50.83b, First Floor)

... (Item No. 50.83b, Second Floor)

... (Item No. 50.83b, Third Floor)

... (Item No. 50.83b, Fourth Floor)

2 Hour Insulated, Flame, Smoke Radiation check Lead Lined Fire Door 57mm 2HR FRL(120/120) 3 Criteria-INTEGRITY/INSULATION/STABILITY WOODEN DOOR-Fire Door Tested in accordance to IS: 3614 Part 2. with prior approval of concerned Superitending Engineer. Providing of 120 min Fire rated lead lined doors system duly tested for 3 criteria-Integrity, Insulation and Stability Criteria as per the IS: 3614 Part 2 and BS: 476 part 22 with standard heating conditions as specified in IS:3614 Part II 1992 and BS: 476 part 20 & 22 1987 to achieve the required integrity, insulation and stability(i.e. to restrict the heat radiation, temperature rise on the non fire side to the maximum of 140 C above the ambient temperature on the exposed surface of the shutter. The fire doors are tested with NCBN technology("Non Combustible by Nature"). Lead lined to check radiation. Code No; 2 Hour Insulated, Flame, Smoke Radiation check Lead Lined Fire Door 57mm 2HR FRL(120/120) 3 Criteria-INTEGRITY/INSULATION/STABILITY WOODEN DOOR-Fire Door Tested in accordance to IS: 3614 Part 2. :: a) Door Frame: Providing Frames for Lead Lined Fire resistant door shutters 1st class Malaysian Hardwood Frame densified and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160 PSI pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 140 X 70mm with 45mm thick two layered 3mm Lead Line Sheets with 10mm overlap from either side & spray quoted with 2 coats of In tumescent paint of minimum 200 micron, with 1 row of Brush-Type Astroflame intumescent strip(imported) of size 10mmx4mm concealed in the groove of the Frame for fire and hot and cold smoke sealing, etc. complete as per direction of Engineer in Charge (Item No. 50.83a)

... (Item No. 50.83a, First Floor)

... (Item No. 50.83a, Second Floor)

... (Item No. 50.83a, Third Floor)

... (Item No. 50.83a, Fourth Floor)

Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9mm with lock plate of 3.15mm thickness reinforced with 35 x 35 x 5mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65mm and 3.15mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15mm minimum size and shape with square bar, suspension shaft of minimum 32mm diameter, hood cover of M.S. sheet not less than 0.9mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete.(I.S. 62481979)(With mechanical gear) (Item No. 39.25)

Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top, 40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating, fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete (Item No. 40.07)

... (Item No. 40.07, First Floor)

... (Item No. 40.07, Second Floor)

... (Item No. 40.07, Third Floor)

Providing and fixing terracota bricks including all material, labour, filling joints, cleaning, curing etc complete.

... (First Floor)

... (Second Floor)

... (Third Floor)

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. (Item No. 23.01)

Providing and fixing Multi-wall hollow polycarbonate sheet panel 10 mm thick for dome including providing and fixing Male female aluminium patti ,neccesary fitting etc. complete.

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150mm in thickness. (Item No. 2.09)

Excavation for roadway in hard murum and boulder including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m.and spreading for embankment or stacking as directed. (Item No. 2.13)

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader/Paver on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- By Mix in Place Method and Grading-I Material (Item No. 3.04)

Wet Mix Macadam -- Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub-base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density. Laying By Grader/Paver. (Item No. 3.23)

Providing and constructing 75mm. thick Modified Penetraction Macadam(MPM) road surface including all materials, preparing the existing road surface, spreading 40mm. stone layers metal 100% crusher broken metal with conical crusher plant, heating and spraying the bitumen of specified grade @ 2kg/sqm, spreading 12mm.size chips compacting with three wheel static roller having weight 8 to 10 MT. to achive the desired degree of compaction as per Technical Specification Clause 506 etc.complete, including applying tack coat of specified grade of bitumen at the rate of 0.30 Kg Sqm. on existing bitumen surface.(VG-30 bulk bitumen rates are considered to arrive at rates) (Item No. 3.36b)

DENSE BITUMINOUS MACADAM: Proving and laying dense bituminous macadam using crushed aggregates of Grading 1, premixed with bituminous binder of specified grade of Bitumen @ 4.50 per cent by weight of total mix and filler, transported to site with VTS, laid over a previously prepared surface, finished to the required grade, level, alignment, and rolling to achieve the desired density for 76-100mm compacted thickness .USING Batch mix type hot mix plant with SCADA, Sensor Paver, Vibratory roller with Stone Dust filler.(VG-30 bulk bitumen rates are considered to arrive at rates) (Item No. 3.44)

BITUMINOUS CONCRETE:-Providing and laying bituminous concrete using crushed aggregates of grading 1, premixed with bituminous binder @ 5.20 per cent by weight of total mix and filler, transported to site with VTS, laid over a previously prepared surface, finished to the required grade, level, alignment, and rolling to achieve the desired compaction for 50mm compacted thickness with specified grade of Bitumen, Excluding prime/tack coat. For Bitumen of specified grade -- USING Batch mix type hot mix plant with SCADA, Sensor Paver, Vibratory roller with Stone Dust filler.(VG-30 bulk bitumen rates are considered to arrive at rates) (Item No. 3.48)

Prime coat-Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including cleaning of road surface and spraying, primer at the rate of 0.60kg/sqm using mechanical means. (Item No. 3.29)

Providing and applying tack coat on the prepared surface heating by fames in Boiler and spraying bitumen set footed in bitumen boller on B.T. surface 2.5kg/10sqm.(VG-30 bulk bitumen rates are considered to arrive at rates) (Item No. 3.30)

Providing and laying in-situ M30 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate(natural sand/VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver, compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound/by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80mm at bottom and 40mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. (Item No. 5.01)

Providing and laying in situ/ready mix cement concrete of M-10 proportion with trap/granite/quartzite/gneiss metal in foundation including necessary form work, compacting and curing etc. complete.(with reversible drum type mixer with SCADA with fine agreegates of required specifications(Natural sand/VSI sand finely washed etc) (Item No. 11.02)

Providing and fixing heavy duty inter locking concrete Grey paving blocks of 60mm thickness of having a strength of 300 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30mm thick including skirting joints and cleaning etc. complete. (Item No. 33.49)

Construction material testing as per tender specifications

Royalty Charges as per tender specifications

Providing and fixing white european type wall-hung, Size 380mm x 650mm x 730mm with wall hung coupled flush tank with float operation auto filling, wall plate/push buttons from inside to opeate the flush tank, rigid flush water pipe having flow rate upto 6.0 Litr/Minute of Jaquar or equivalent make including PVC soil pipe, vent pipe upto outside face of wall, 100mm dia PVC plug bend inlet pipe all fittings, MS PC chair backet with SS rack bolts cutting &making good walls, floors etc as directed by Engineer incharge .(Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Providing and fixing White glazed with bottle trap earthenware Wash Hand Basin of 55x40 cm size including cold water piller taps, brackets, rubber plugs and brass chain, angular stop tap, chromium plate bottle trap and necessary pipe connections including UPAC waste pipe and trap upto the outside face of the wall, making good the damaged surface, testing etc. complete.

Providing and fixing white glazed urinal with Pressmatic auto closing valve having flow rate up to 4.0 Litr/Minute of Jaquar/Cera/Hindware /Perryware or equivalent make with P.V.C. waste pipe with fitting arrangement etc.complete as directed by Engineer in charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Providing and fixing Hand shower (health faucet) with 8mm dia. 1m long flexible tube having wall hook with approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.(SSR 21-22)

Providing and fixing stainless steel sink of size 600 x 510 x200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete.

Providing and fixing C.P. 2 Way BIB cock with wall flange of approved make including ecessary sockets/ union nut etc. complete as directed by Engineer in charge.

Providing and fixing of TOWEL RACK 600MM LONG WITH LOWER HANGERS STAINLESS STEEL, etc complete.

Providing and fixing of C.P.Soap dish hooker jaquar make continental, etc complete.

Providing and fixing of C.P.Toilet paper holder jaquar make continental, etc complete.

Providing, laying and fixing P.V.C. pipe of 75mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trenchfilling etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 110mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trenchfilling etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Supply, installation, testing & commissioning of PVC SWR (Grade B) pipe as per IS 13592, of approved make vertically in shaft, necessary cutting to the required length including short pieces, assorted fittings such as plain tee and bend single/ double Y, offsets etc. as per IS 14735, jointing with solvent cement & rubber rings, clamping on wall using PVC pipe clips and giving water-tightness test for the pipes along with making holes in walls/floor grooving and redoing the same and brick support etc. complete as per directions of engineer-in-charge. 110mm dia (Grade B)

Supply, installation, testing & commissioning of 75mm PVC Nahani Trap as per IS 14735,with material and labour etc. complete as per directions of engineer-in-charge.

Supply, installation, testing & commissioning of PVC Multi floor Trap as per IS 14735, with material and labour etc. complete as per directions of engineer-in-charge.

Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and fixing C.I. vertical jalli of the specified size at the collection point of RWP on terrace to be with material and labour including provision of roof flashing of 6mm thickness as per details etc. complete as per directions of engineer-in-charge.150 mm X 150 mm

Providing and fixing in position UPVC ultra violetstabilized 110mm outer diameter cowl dome confirming toI.S.-4985 including making joints with solvent cement etc.complete

Supply, installation, testing & commissioning of exposed on wall faces, floor, shaft & Terrace following sizes of Lead Free Solvent Weld Schedule 40 CPVC Pipes conforming to ASTM D 1785 for water supply including provision of all fittings such as elbows, Tees, unions, reducers etc. as per ASTM D 2467, cutting of pipes, jointing with solvent cement joints as per manufacturers specifications, hydraulic testing, including holes in walls, slabs etc. provision of GI Brackets & Clamps and making good the damages by bringing them to good original condition, etc. complete as directed by the engineer-in-charge. 65 mm dia

Providing and fixing on walls/ ceiling/ floor CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.25 mm dia

Providing and fixing on walls/ ceiling/ floor CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.20 mm dia

Providing and fixing of CPVC SDR 11 Ball Stop cocks for hot water line. 50 mm dia

Providing and fixing of CPVC SDR 11 Ball Stop cocks for hot water line. 40 mm dia

Providing and fixing of CPVC SDR 11 Ball Stop cocks for hot water line. 32 mm dia

Providing and fixing of CPVC SDR 11 Ball Stop cocks for hot water line. 25 mm dia

Providing and fixing of CPVC SDR 11 Ball Stop cocks for hot water line. 20 mm dia

Providing and fixing of CPVC SDR 11 Ball Stop cocks for hot water line. 15 mm dia

Supply, installation, testing & commissioning of Wafer Type Butterfly Valves with Body of Cast Iron, Disc of Cast Iron/Stainless Steel and body lining of EPDM / Nitrile Rubber including jointing with Galvanised Iron pipes including hydraulic testing (Operating pressure not less than 16 Kg/Sq.cm) etc. complete as directed by the engineer-in-charge.65 mm dia

Providing & fixing CI `Y' Strainer (screwed/ flanged) with stainless steel fine wire mesh perforated sheet basket with necessary flange/ unions nuts, bolts and washers complete as required (on pump suction). 50 mm dia

Supply & Fixing in position galvanised iron puddle flanges of approx. 60 cm length with flange on one end and welded to mild steel plate (8mm thick) in the centre etc. complete as directed by engineer-in-charge. Flange on both end 150mm

Supply & Fixing in position galvanised iron puddle flanges of approx. 60 cm length with flange on one end and welded to mild steel plate (8mm thick) in the centre etc. complete as directed by engineer-in-charge. Flange on both end 100mm

Supply & Fixing in position galvanised iron puddle flanges of approx. 60 cm length with flange on one end and welded to mild steel plate (8mm thick) in the centre etc. complete as directed by engineer-in-charge. Flange on both end 50mm

Supply & Fixing in position galvanised iron puddle flanges of approx. 60 cm length with flange on one end and welded to mild steel plate (8mm thick) in the centre etc. complete as directed by engineer-in-charge. Flange on both end 32mm

Supply & Fixing in position galvanised iron puddle flanges of approx. 60 cm length with flange on one end and welded to mild steel plate (8mm thick) in the centre etc. complete as directed by engineer-in-charge. Flange on one end 100mm

Supply & Fixing in position galvanised iron puddle flanges of approx. 60 cm length with flange on one end and welded to mild steel plate (8mm thick) in the centre etc. complete as directed by engineer-in-charge. Flange on one end 65mm

Supply & Fixing in position galvanised iron puddle flanges of approx. 60 cm length with flange on one end and welded to mild steel plate (8mm thick) in the centre etc. complete as directed by engineer-in-charge. Flange on one end 50mm

Supply & Fixing in position galvanised iron puddle flanges of approx. 60 cm length with flange on one end and welded to mild steel plate (8mm thick) in the centre etc. complete as directed by engineer-in-charge. Flange on one end 32mm

Supply & installation of Ductile Iron Manhole Covers with frame,& openable hinge of 600mm Dia. (Light Duty) for UGR including all necessary supports, grouting of the frame in RCC, making arrangements for recessed locking of the Manhole cover etc. complete as directed by engineer-in-charge.

Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete. 40mm

Installation, Testing & Commissioning of Stainless Steel Vertical In-line Pump Sets consisting of 1 Working & 1 Standby pump having Built-in Overload Protection, Motor Housing, Suction Plate, Bottom Screen & all Screws to be of stainless steel, Motor Cover & Pump Housing to be of corrosion proof Cast Iron, Pump to have Stainless Steel Impeller & Double Mechanical seals in oil chambers, including necessary supports/ foundations, Main Suction Header & Delivery Header along with Y' Strainers,Isolation and N.R valve, Pressure Guages & Pressure Switches, all necessary fittings,and Cable from Panels to the individual pumps etc including Electrical Control Panel with 1 VFD for Operation & Control of pump-sets including provision of Pressure Vessel. complete as per directions of engineer in charge (AT TERRACE), 1 pump to run on VFD and the VFD shall be transferrable to any of the pumps, Contractor to submit the GA drawing along with the Control layout to the Consultants before manufacturing of the same. Domestic Pumps (Pump Discharge = 3 LPS, Head = 15 m (1 W + 1 S)

Excavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (BdA-1/259) Lift 0 to 1.5 M Excavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum.()

Providing & laying including all necessary excavation in all strata, supply of labour for lowering, jointing RCC NP 2 class pipes conforming to IS:458 from first manhole upto STP including necessary ramming of subgrade after excavation to achieve a designed gradient & alignment by site rails & boning rods for proper leveling & making the joints water-tight with cement mortor 1:1 joints hemp yarn including 6" thick 1:3:6 C.C. bedding & encasement on all sides throughout length, excavation in all types of soils, refilling, curing etc. complete as per directions of engineer-in-charge including dewatering wherever necessary.150mm

Constructing Gully Traps/ Inspection chamber with precast steel fibre reinforced concrete frame and covers (S.F.R.C. frame and covers) Providing and constructing B.B. masonry in 230 X 100 X 75 mm brick inspection chamber with 100mmthick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in CM 1:5 proportion half round RCC pipe of required dia, precast S.F.R.C. frame and cover heavy duty 225 kg., plastering both inside and outside in CM 1:3 with cement finish,, 100 mm thick PCC 1:2:4 coping on B.B. masonry etc. complete as directed by Engineer-in-charge. Note : i) Wall thickness : 0.23 M for depth of 1.2 M and 0.35 M for balance depth exceeding 1.2 M. 600 x 450mm (upto 0.9 m depth)

600 x 600 mm (upto 0.9 m depth)

Providing and constructing on sewer line, B. B. masonry circular manhole with concentric cone 1.2 M dia. at bottom and 0.5 M dia. at top and upto a depth of 2.00 M with 23 cm. thick in 230 X 100 X 75 mm brick masonry in CM 1:5 proportion plastering both inside and outside in CM 1:3 with cement finish, half round RCC pipe of required dia excluding excavation including PCC1:3:6 in bed 100 mm thick , haunches and channels in 1:2:4 proportion concrete, finishing channels in smooth rendering, providing C.I. dapuri type steps each weighing 5.5 kg., 100 mm thick 1:2:4 coping on the top of the masonry & below frame including providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia. heavy duty 225 kg. etc. complete as directed byEngineerin- charge. Note : The rate of this item isinclusive of hydraulic testing of chamber. 560 MM Dia Circular Chamber (Above 1.2 m depth)

Providing & laying including all necessary excavation in all strata, supply of labour for lowering, jointing RCC NP 2 class pipes conforming to IS:458 from first manhole upto munciple drain including necessary ramming of subgrade after excavation to achieve a designed gradient & alignment by site rails & boning rods for proper leveling & making the joints water-tight with cement mortor 1:1 joints hemp yarn including 6" thick 1:3:6 C.C. bedding & encasement on all sides throughout length, excavation in all types of soils, refilling, curing etc. complete as per directions of engineer-in-charge including dewatering wherever necessary. 200mm

Providing and laying cast in situ Brick Masonry gutter/ drain with following specification along roads / courtyards including excavation, P.C.C. & fixing of RCC perforeted cover (heavy duty), over the drain in proper line and alignment, including back fillings, dewatering etc. complete including: (depth varies from 450 mm to 2000 mm ) For External Surface Drain 300mm Wide

Constructing catch pits with precast steel fibre reinforced concrete frame and covers (S.F.R.C. frame and covers) Providing and constructing B.B. masonry in 230 X 100 X 75 mm brick inspection chamber with 100mmthick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in CM 1:5 proportion half round RCC pipe of required dia, precast S.F.R.C. frame and cover heavy duty 225 kg., plastering both inside and outside in CM 1:3 with cement finish,, 100 mm thick PCC 1:2:4 coping on B.B. masonry etc. complete as directed by Engineer-in-charge. Note : i) Wall thickness : 0.23 M for depth of 1.2 M and 0.35 M for balance depth exceeding 1.2 M. 450 x 600 mm

Providing and constructing on sewer line, B. B. masonry circular manhole with concentric cone 1.2 M dia. at bottom and 0.5 M dia. at top and upto a depth of 2.00 M with 23 cm. thick in 230 X 100 X 75 mm brick masonry in CM 1:5 proportion plastering both inside and outside in CM 1:3 with cement finish, half round RCC pipe of required dia excluding excavation including PCC1:3:6 in bed 100 mm thick , haunches and channels in 1:2:4 proportion concrete, finishing channels in smooth rendering, providing C.I. dapuri type steps each weighing 5.5 kg., 100 mm thick 1:2:4 coping on the top of the masonry & below frame including providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia. heavy duty 225 kg. etc. complete as directed byEngineerin- charge. Note : The rate of this item isinclusive of hydraulic testing of chamber. 560 MM Dia Circular Chamber (Above 1.2 m depth)

Providing & Fixing Wafer Type Butterfly Valves with Body of Cast Iron, Disc of Cast Iron/Stainless Steel and body lining of EPDM including jointing with Galvanised Iron pipes including hydraulic testing etc. complete as directed by the engineer-in-charge. 100mm

Providing & Fixing of water meter with strainer as per approved make including supply of required specials & isolation valves, hemp yarn etc complete to make it water tight and providing locking arrangement to the same etc. complete as per directions of engineer-in-charge. 100 mm dia

Construction of B.B. Masonry chamber for water meter of following size including excavation, cement concrete bedding of 150 mm thick and plastering with cement mortor 1:3 from inside and outside and fixing air tight RCC covers (heavy duty) including curing etc.complete as per direction of engineer-in-charge. 1200mm x 750mm

Supply & Fixing in position galvanised iron puddle flanges of approx. 60 cm length with flange on one end and welded to mild steel plate (8mm thick) in the centre etc. complete as directed by engineer-in-charge. Flange on both end 150mm

Flange on one end 100mm

Supply & installation of Ductile Iron Manhole Covers with frame,& openable hinge of 600X600 Dia. (Light Duty) for UGR including all necessary supports, grouting of the frame in RCC, making arrangements for recessed locking of the Manhole cover etc. complete as directed by engineer-in-charge.

Supply, installation, testing and commissioning of Skid mounted Hydro-pneumatic system of Vertical in line pump set with Variable Frequency Drive . Domestic Water Supply System For Building -330 lpm, Head - 50 meter (Approx. 5hp /pump) Pump Qty - 3 (2working +1 stand by / Duty Assist) Siemens switch gear make control panel along with PLC, PID Controller with all necessary cascade system automation, Power & Control MCB, MPCB , Over load \ Under load, SPP \ RPP, Dry run and all necessary pump & voltage protection, Indication lamp, Digital Pressure indicator cum controller. Danfoss make Pressure Transmitter & Pressure switch, Gauge, Pressure Tank etc. Skid for pumpset with Hot deep Galvnised Suction & Delivery Header Plumbing Accessories along with Ball Valve, NRV, Y type Strainer Polycab make power cable for pumpset & Control cable float switch sensor , control cable for sensor etc complete as per direction of Engineer-in-charge. Pumpset & Control Pannel shall be company assembled factory fitted system with test certificate should be submitted. Vendor to submit performance curves and technical catalog of the proposed model for review & approval by consultants.

Providing and constructing recharge ring well of required dia with casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, including excavation and stacking the soil and disposing as per the instructions of engineerincharge, all complete as per direction of Engineer in-charge, upto 90 metre depth below ground level. Filling with gravels and boulders from outside of the circumference of the collar of 1.2m dia upto 6m so as to allow infiltration of supplied water from inside of the well through the gap between the collars to the ground water aquifer Supplying & fixing 40 mm thick DI heavy Rain water grating over storm water channel of heavy duty. b) 600 x 450 MM (450wide)

SITC of Electric Traction Passenger Lift with · Rated capacity :- 13 Passenger884Kg · Floors :- G+4 floor (5 Stops/5 Landings) · Travel :- 20 mtrs · Location of Lift Machine:- MR/MRL · Rated speed :- 1.0mps VS · Car/Landing door clear opening of 900 mm wide x 2000 mm high · Clear Car size of 1300 mm wide x 1350 mm deep x 2250mm high · Lift shaft available having clear size of 2600mm wide x 1900mm deep, pit depth-1500mm, Overhead height -4500mm · Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid(non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory). · Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge.. · COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor. • Clear Car size of 1300 mm wide x 1100 .mm deep x2000 .mm high · LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings. · Lift controller of simplex full collective based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as overcurrent, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. ,various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters, The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class. · ARD complete with necessary SMF VRLA batteries. · Fireman controller having fireman switch at fire Landing. · CCTV surveillance system comprises of 2nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for min. 90 days with min. 20" FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. · Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength.

ITC of Duplex Lift control system for two nos. microprocessor/PLC based simplex lift controllers along with necessary software with programming and hardware e.g. logic board, necessary communication/control/data cabling laying in rigid PVC conduits/trunking etc. complete.

Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting mains with 1x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module duly erected.

Supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Point wiring for ceiling fan concealed type in min 20 mm HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification no. WG-PW/CW

Point wiring for light/bell concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG?PW/CW

Supplying and erecting bulk head LED fitting max. 10W with high transitivity diffuser with system lumens output of min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting CRCA powder coated corridor/passage light LED fitting (4 feet) Max. 17W with high transitivity diffuser with system lumens output of Min. 2000 lumens , min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Providing recess in brick wall suitable for erection of exhaust fan up to 450mm. sweep complete with grouting of nut, bolts, plastering and colour washing to match the colour of the wall for the wall thickness of 225 mm.

Supplying & erecting 22 SWG G.I sheet metal cawl sector shaped with 25 x 25 x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 300 mm as per specification no FG-FAS/MSC

Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation.

Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, max. energy consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% with IR remote control/compatible speed regulator, Temperature Rise of Max. 40 deg. C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & commissioning 2 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying, erecting & commissioning 4 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying & erecting G.I. pipe ‘A’ class 40 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per specification no. CB-CE

Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI

Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI

Supplying, installation, testing and commissioning of booster fire pump [BP] suitable for water discharge of 900 LPM at 35 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 7.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following :(a) Horizontal/vertical type, single/multi stage, centrifugal casing pump of cast iron body & bronze/CI impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520.(b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.(c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required.(d)Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/BP

for 5.5/ 7.5 kW centrifugal type booster pump 1no (1working), add Rs…....

Supplying & erecting D.O.L Starter suitable for 415 V, 3 phase 50 cycles with no volt coil and overload element with necessary materials and connected to supply up to 7.5 H.P.

Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting 100 mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, SS screen, end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS

Supplying and erecting 100 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating, as per specification no. FF-VL/SV

Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 25 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV

Supplying and erecting stainless steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Supplying and installing wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) along with necessary accessories complete as per specification no. FF-FFA/HV

Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FF-FFA/NZ

Supplying and erecting fire brigade header ( Siamese connection )of 150 mm dia, for supplying water in fire tank complete as per specification no. FF-FA/FMC

Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS

Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade / SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Supplying, erecting, testing and commissioning vane type water flow detector 100 mm dia. with 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4)Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT ( Single pole double track ) synchronised switches 7) serviceable without draining pipes.

Supplying and erecting fire resistant mortar (20 kg) with fire resistance class S90 as per National Electrical Code (NEC) SP30-2011 suitable to seal the openings of all kinds of cables, pipes and cable support system in steel, aluminium and plastic profiles ( except hollow core conductors). The residual openings shall be closed with filler, as per specification no FF-FRM.

Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Supplying, installing, testing, and commissioning of portable fire extinguishers of ABC dry powder stored pressure type fire extinguishers of 6 Kgs.capacity Complete with standard discharge valve with tube, CI bracket for wall mounting etc. complete as per confirming to IS : 15683 complete all the work up to the satisfaction of the Engineer in charge.

Providing and fixing in position statutory Signage's made out of 3mm thick opaque PVC foam board, machine cut, non reflective, auto glow (type & Make), with silicon adhesive for safe evacuation of occupants in case of emergency. Sign indicators should be provided at prominent places as per Fire Provisional NOC (As per - IS-9457, IS-12349, IS-12407). complete all the work up to the satisfaction of the Engineer in charge.

Providing, laying, testing & commissioning of 100mm dia resilient rubber neoprene lined single arch Vibration eliminators (Expansion bellows) suitable for Design Pressure 16 kg/sq cm and test pressure 24 kg/sq cm. complete all the work up to the satisfaction of the Engineer in charge.

Providing Floor mounting stand for keeping 4 Nos. of FIRE buckets 1500mm in length, 900mm in height frame made out of 30x30x4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of silver paint complete.

Planning, designinng, approval and necessary certification of electrical layout and work of internal and external electrification including networking AC's, UPS, Panel, DB and transformer substation including RMU unit, HT cabling from source of supply to building panel location plus MSDCEL sanction and EI permission, statutory approval with fees, charges of local bodies, etc complete based on turnkey basis(Bidder should visit the site and study the actual requirement of necessary items).

Planning, designinng, approval of external and internal IP based CCTV and survelience system including servers VMS, recording, monitors, work station, CAT 6 cable, LAN network with Wi-fi provision, for adminstrative building (internal and external area) plus 10 desktop computers with printer, 5 laptops, internet connection for 3 years service and warranty.

Providing and supplying furniture items like Desks: Types (executive, workstations), dimensions, materials, Chairs: Ergonomic, visitor, conference chairs with s Tables: Meeting tables, coffee tables with Storage Units: Cabinets, shelves, filing systems. Reception Area Furniture: Sofas, lounge chairs, reception desks, etc complete as directed by project incharge/client, etc complete

SITC of solar power plant of capacity 100 Kw including supporting structure and netmetering, necessary approvals from local authorities, etc complete as per specifications as directed by project incharge/client.