SPECIAL REPAIR TO BLDG NO. P-06, P-172 AND P -174 UNDER ZONE-I AREA AT JAIPUR MIL STN

Amount

Taking down cement plaster or cement lime plaster/ tiles of any descrption on PCC/ stone surface/ brick surfaces of wall or ceiling including raking outs joints, hacking for key scrubbing down with water etc

M & L Rendering 15 mm thick on stone masonry wall surfaces in CM 1:6 finished even and smooth without using extra cement

M & L rendering 15mm thick on stone masonary surfaces or surface other than fair faces of brick work on wall in CM 1:4 finished even and smooth without using extra cement.

M & L Rendering 10 mm thick on ceiling in CM 1:4 finished even and smooth without using extra cement

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distermper over a coat of birla putty

M & L preparing new plastered surfaces and applying three coats of oil bound distemper on ceiling over a coat of birla wall care putty

M & L preparing new plastered surfaces and applying two coats of cement base paint on wall

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing) , removing serviceable tiles to store and rubbish off the premises

M&L 25mm thick plain cement concrete type B-0, 1:2:4 ( 12.5mm graded stone aggregate) as in floor

S&F coloured glazed ceramic tiles size 300 x 450mm x7mm thick edge cut/ joint free on walls etc in the combinatin of light and dark shade concept set & jointed in neat cement slurry & pointed in white/ coloured cement to match over 15mm thick plaster in CM (1:4)

Non skid cermic coloured tiles 7 to 8mm thick joint free (square/ rect) area of each tile exceeding 0.06 sqm but not exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match & incl 15mm thick screed bed in CM 1:6

S&F light shade vetrified ceramic tiles edge cut 10mm thick ( square/ rectangular ) polished, area of each tiles not exc 0.36sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match over & incl 15mm thick screed bed in CM (1:4) finished fair and even

All as per item No 12 above but as in skirting/ vertical surface over & including 10mm thick rendering on stone masonary surface or surface other than fair faces of brick work in CM 1:4

Taking down Flush/pannelled/ Aluminium door of area exc 1.00 Sqm but n exc 4 Sqm each (without taking out frame) and refixing in same position after carryout necessary repair work complete as directed.

Dismantling asbestos cement ( corrugated , semi corrugated etc ) sheet in roof covering all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling all as specified

S&F hanger 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified

M&L 12mm thick perforated particle board/ tiles for insulation and accoustic purposes, 60cm x 60cm in size, fixed with nails to timber frame work or with staples on snap grid

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in soft/ loose soil

M&L for PCC 1:4:8 type D2 in foundations, fillings and mass-concrete

M&L Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm

Removing excavated material exc 250 m but not exc 500 m and deposited where directed at a level n exc 1.5 m above the starting point.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 for raising of height of drain, manhole / wall complete all as specified.

M&L brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in CM (1:4)

M&L reinforced cement concrete Type B0 1:2:4 (12.5 mm graded aggregate) for slabs supported on walls, Chajjas, beams and columns in floors, deck slabs and shelves and the like

M&L Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape requried, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

M&L Mild steel TMT bars 6 mm to 8mm dia and over, cut to length, bent to shape requried, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

All as per item No 28 above but 5mm over upto and including 10mm dia in stirrups, spacers and binders etc

M&L formwork of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 20mm thick

Rendering 15 mm thick cement plaster in CM 1:4 on other faces on brick masonry (External surface)

Rendering 15 mm thick cement plaster in CM 1:6 on other faces of brick work (Internal Surface) including finished even and smooth without using extra cemnet

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distermper over a coat of birla putty

Filling under floors including spreading, watering and levelling in layers not exc 25cm thick complete

M&L broken stone or boulders for hardcore of gauge not exc 63mm, deposited , spread and levelled in layers not exc 15cm thick watered and rammed to a ture surface

M & L 100mm thick plain Cement Concrete1:4:8 type D-2 (40mm graded aggregate) in sub base of floors

M & L 40mm thick plain Cement Concrete1:2:4 type B1 (20mm graded aggregate) in sub base of floors

M&L PCC 1:3:6 type C2 ( using 40mm graded stone agg) 75 mm thick as in plinth protection.

S&F for two way bib cock with wall flange and aerator complete all as specified and directed by Engr-in-Charge

S&F in repair PVC connection 15mm dia 60cm long with 2 Nos brass check nuts with washer complete all as specified

M&L CP fancy type centre hole basin mixer 15mm bore cast copper alloy with 450mm copper hose/ braided hose without popup waste system quarter turn complete all as directed

M&L of 15mm brass CP mixer hot & cold water screwed down for iron pipe and fixed

M&L towel rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats ( minimum weight 170 gms)

S&F angle stop valve cast copper alloy chromium plated screwed for iron pipe 15 mm bore

S&F brass chromium plated shower rose 65mm size with swivel joint type including fixing to steel pipe of 15mm bore or union includng taking down of old shower rose of any size and type

S & F as in repair stop valves cast copper alloy, fancy type chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 15 mm bore fixed .

S&F 15mm bore chromium plated bib taps (fancy type) long body cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes all as specified

Demolition of old existing unserviceable WHB glazed and S&F vitreous china wash hand basin white of size 550 x 400mm flat back excluding taps, waste china and plug but including brackets including cutting for and pinning in ends of brackets or erecting stand complete

Demolition of old existing unsv EWC seat and S&F vitreous china wash down water closet pan ( pedestal pattern) white including connections to drain ( or outgoing pipe) and to flushing pipe anti sypohonage pipe etc & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device complete

S & F in repair PVC valveless, syphonic action type flushing cistern 10 liters capacity, low level, white with inlet, ball valve, float and handle incl brackets and flush pipe of polyethylene of low or high density or PVC, 32mm dia suitable for low level cistern,

S&F in repair waste fittings brass chromium plated for glazed ware sinks basins etc with long screwed shanks and fly nuts flange end bedded in red leads cement and other end fixed.

S&F in repair bottle trap with internal partition 32mm of PTMT having minimum water seal of 25mm (minium weight of 32mm - 260 gms/ 40mm -270 gms0 fixed.

S&F in repair stop valve 15mm copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions

S&F in repairs stop valves 20mm bore copper alloy screwed down high pressure with crutch of butter fly handle screwed both ends for iron pipe or for union

M&L of healthy faucet ABS body with 2 mtr SS braided connection pipe.

Dismantling of old unserviceable trap and S&F of PVC Nahani / floor trap and square in size of 100 x 100mm including MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap/ Nahani trap

Dismantling and taking up or down the existing unserviceable GI pipe and S&F new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and celing or laid in floors of following :- (a) 15 mm bore

(b) 20 mm bore

Refixing old steel tubing and connections 15mm bore in new or old position (Walls, ceiling, floors, etc.)

Refixing old steel tubing and connections 20mm bore in new or old position (Walls, ceiling, floors, etc.)

Dismantling old unserviceable PVC/ RCC water tank complete all as directed capacity exceeding 250 ltr and not exc 500 ltrs

All as per item No 61 above but exc 500 ltr but not exc 1000 ltr

S & F 500 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe pipe etc complete all as specified in SSR Part I, Make - Sintex or eqivalent

All as per item No 63 above but 1000 ltrs capacity

Disconnecting existing tanks of cap 500 Ltrs, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing etc measured separately)

All as per item No 65 above but 1000 ltrs capacity

S & F Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed bore dia of pipe 20mm

M&L for providing circular, raised platform of height 20cm below the tank and base 15cm more than the external dia of tank of PVC cylindircal water tank of capacity 500 / 1000 litre using PCC 1:3:6 type C-1 using 20mm graded stone aggregate with smooth finish complete all as directed.

S&F in repairs vitreous china water closet Indian type 580mm long pan white with 'P' or 'S' trap front or ack inlet footrest including provn of lime concrete bedding including connections to flushing cistern/ pipe and making good distrubed portion to match

S&F in repair box type mirror PVC cabinet of size 475 x 600 x 150mm all as specified

S&F soap dish vitreous china white approximate size 160 x 160 x 90mm fixed to plugs with chromium plated (CP) brass screws

S&F toilet paper holder for CP fixed to walls with chromium plated (CP) brass screws fixed in repair

S&F UPVC (SWR) pipe single socketed, any in length with rubber ring joints laid in trenches or in floors type 'B' ISI marked of 75mm bore

S&F 75mm PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls as directed.

S&F UPVC (SWR) pipe single socketed, any in length with rubber ring joints laid in trenches or in floors type 'B' ISI marked of 110mm bore

M&L PCC 1:3:6 type C2 concrete bed to drain pipes including packing under and haunching against the side of pipes after they are laid and tested in 110mm bore pipe

S&F UPVC (SWR) bends of any radius 75mm bore

S&F UPVC (SWR) bends of any radius 110mm bore

S&F UPVC (SWR) junction single (single T) equal or unequal 75mm

S&F UPVC (SWR) junction single (single T) equal or unequal 110mm

S&F UPVC (SWR) vent cowl 110mm

S&F PVC (SWR) floor trap 75mm dia plain with grating including joining with solvent cement

M&L PVC (SWR) gully trap 125/110 mm setting & jointing with solvent cement

S&F Corner glass shelf (large) of size 300x300mm complete all as specified and directed by Engr-in-Charge.

M&L in repair fancy type SS brackets for curtain rod fixed complete all as directed.

M&L in repair of 20mm dia drapery fancy type curtain rod fixed.

M&L in repair for fancy type caps/ side bulbs PVC powder coated suitable for curtain rod fixed.

S&F factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (stiles) with 2, 4 or raised panel design with2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face supplying & fixing in frame at site as per specification & drawing including PVC sheet fixed on flush shutter in lipping in case of PVC sheet is heat bent as lipping on the edges of doors

S&F solid PVC frame ( single rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth out integral skin with suitable metal stiffner and fxed with 100 x 8 sheet metal CSK screws complete all as specified and shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S & F framed work as in doors or gates of angle or other section as chowkhat or shutters, tie bar, hold fast, guard bars, brackets etc and fixing complete Fe 290 (Gde-E-165)

S & F 35mm thick factory made plain, framed, paneled door shutters kiln seasoned and chemically pressure treated second class, hardwood (two panels) with lock rail and panel of 9mm thick BWP commercial marine grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive confirming to IS-710. The size of rails and style shall be as per IS-1003.

S & F 35mm thick factory made second class hardwood glazed and skelton door shutter kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. The size of members of shutters shall be as specified in MES SSR Part-I complete all as directed.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamp, hooks for hanging fans and similar small articles conforming to Fe- 290 Gde E- 165 including necessary welding etc and fixed in position

Cutting holes in stone/ brick walls built in CM for inserting hold fast & making good dismantled portion in CM (1:3) depth of embaded portion of hold fast n. exc half brick

S & F butt hinges of size 100mm medium weight cold rolled mild steel and fixed

S&F aluminium anodised barrel tower bolts 150mm long of extruded section

S&F aluminium alloy anodised sliding door bolts 300mm long with hasp and staple ( bolt type) & fixing clips of sheet or extruded section & fixing bolts & sliding bolts of extruded section

S&F aluminium anodised handle 125mm size

aluminium anodised floor door stopper overall length 140mm double legged with rubber shoe fixed to bottom rails of door

S&F MS spring hinges 300mm ordinary rat tail rod pattern including roller and roller plate complete fixed to wooden/ angle iron chowkhats

S&F galvanised mil steel wire cloth 0.50mm nominal dia of wire and average width of aperature 1.00 mm and fixed with tinned tacks or galvanised wire staples all as specified

M & L Preparing new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer

M&L granite 16 to 18mm thick ( of any type) work ( table rubbed and polished in steps, jambs, pillars, windows cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

Cutting holes into or through cement concrete slabs, chajjas etc reinforced or otherwise ssuperficial area not exc 100 sqcm

Taking down chowkats or frames with shutters exc 1.50 sqm but n exc 4.00 sqm each (without taking off shutters from the frames).

Taking down chowkats or frames with shutters not exc 1.50 sqm each (without taking off shutters from the frames).

Taking down shutters of any description exc 1 sq.m and n not exc 2.00 each

S & F factory made steel window with side hung shutters factory made including box type hinges with steel handle and steel peg stay complete without glazing bars devetailed or welded incl inserting the hold fast in stone masonry and make good the disturbed masonary

S & F factory made steel window with side hung shutters including box type hinges with steel handle and steel peg stay complete without glazing bars all as specified

S & F factory made steel ventilator with top hung shutter including hinges, steel peg stay and handle complete all as specified

S & F 4 mm thick plain sheet glass ordinary quality and glazing with oil putty in sqaures not exc 0.5 sqm in each pane.

Aluminium powder coated frame for holding of three track sliding shutters fixed type with aluminium section weighing 0.55 Kg/mtr incl necessary joining, cleats glazing clips, rubber packing powder coated aluminium snap beading, screws etc and beading for fixing of galvanised wire mess complete all as specified

Aluminium powder coated frame for fixed type with aluminium section weighing 0.55 Kg/mtr incl necessary joining, cleats glazing clips, rubber packing powder coated aluminium snap beading, screws etc and beading for fixing of galvanised wire mess complete all as specified

Aluminium powder coated door/ window shutter openable/ sliding type, partion wall with al section weighing 0.55 Kg/mtr incl necessary joining cleat, glazing clips, rubber packing aluminuim powder coated snap beading, screws, handle & tower bolt etc complete all as specified

S&F aluminium anodised frame for door, windows ventilators with one or more rebates including joining cleats for fixing etc complete

S&F plain glass 5mm thick ordinary quality & glazing in square as required & directed.

S & F framed work as in grills, gratings etc with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors ladders, framed balusters, walk ways etc and fixing complete Fe 290 (Gde-E-165)

M & L plain Cement Concrete 1:4:8 type D-2 (40mm graded aggregate) in sub base of floors

M&L chequered cement concrete tiles 20cm x 20cm x 20mm thick , set , jointed and pointed in neat cement slurry in floors with grey cement and pigment over 20mm thick screed bed in CM 1:6

M & L for 25 mm thick sand cushion layer complete all as specified and directed

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement all as specified and directed

M&L scrapping roof surface with wire brushes and washing with water etc including taking down old cement plaster, PCC of any thickness, description in any situation ,position and roof treatment any type for making good to receive new roof treatment any type. and removal of same from site to out side of MOD land complete all as specified and directed.

M&L screed bed or bedding layer of 15mm thick in CM 1:6 for laying floor finishes in roof, finished even and smooth without using extra cement complete all as specified & as directed.

M&L painted cement plastered surfaces with one coat of cold applied bituminous primer @ 0.40 ltr/Sqm conforming to IS-3384 and laying APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5kg/sqm, reinforced with polyester non woven fabric (weighing not less than 150gms/sqm) shall only be used. It shall be laid by torch application. Side over laps shall be 75mm and the end lap shall be 100mm and all over laps and joints shall be sealed by torch application. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside the parapet groove. This shall be finished by a membrane flashing.

M&L preparation of APP based polymeric surface and applying two coat of aluminium paint all as specified & as directed.

M&L padding in PCC 12:4 type B-0 ( using 12.5mm size graded stone aggregate) laid to provide a finished slope of 1:30 finished even and smooth without using extra cement all as specified

M&L plain cement concrete type B-1, 1:2:4 (20mm graded aggregate ) in roof kerbs or mud stops, rounded or chamfered on edges

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for including removal of rubbish from the site complete.

M & L cutting out cracks to V section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as secified and as directed

M&L cutting groove in brick wall/ stone masonry , 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3

Dismantling plain or corrugated steel / FRP sheeting any gauge, thickness including nainital or similar pattern roof /wall covering

Dismantling wrought iron or mild steel work of any description nototherwise provided for

S & F steel work in tubular/ square/ rectangular trusses incl special shaped washer etc, complete using ERW orinduction butt welded tubes conforiming toIS 1161-1979 graded St-240

M & L Preparing newly untreated steel surfaces of any descripton over 10 cm wiidth or girth and applying two coat of synthetic enamel paints over a coat of red oxide primer

M&L pre- painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified

M & L taking down existing treatment of chajja and applying 15mm thick plastering to chajjas in CM 1:3 including making dripping/ throating and PCC 1:2:4 for covering making proper slope etc complete at ground/ first floor all as specified and as directed

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in stone, concrete block or slab wall.

M & L taking down existing treatment of facia (parallel/ downwords projection of roof/chajja), finishing with 10 mm thick plastering in CM 1:3 (using chiken wiremesh or equivalent materials for holding plastering in facia) and applying cement base paint at ground/ first floor incl scaffolding arrangement , trestles, ladders etc all as specified and as directed

M & L for preparation of old decorated surfaces of walls, pillars and cornices including brooming down and cleaning the surface and applying one coat of white wash all as specified and directed

M & L for preparation of old plastered or unplastered decorated surfaces and applying one coat of white wash on ceiling

M & L for tropping with burnt brick tiles 20 mm thick laid over 15 mm thick in CM 1:3 mixed with powder integral water proffing compound at 01 Kg per bag of cement (of 50 Kg). The tile jointed and pointed in CM 1:3 (mixed with water proofing compound at 01 Kg per bag of cement) and coved filled in PCC 1:2:4 type B-0 of radious 75 mm at roof junction parapet wall and other vertical surface and painted with hot pavig bitumen grade 30/40 confirming to IS-73 @ 1.20 kg per sqm complete all as specified and directed

Supply only water proofing compound

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces incluiding filling of depressions etc and applying two coats of oil bound distemper of approved tint.

M&L of one coat of Birla wall care putty on walls etc.

M&L preparation of old plastered surface of walls and applying two coat of cement base paint

Taking down carefully surface aluminium or copper point wiring with PVC casing or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, regulators, sockets, light fittings etc and making good disturbed surfaces of walls, floors, etc all as directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular sunken boxes for mounting switxhes, sockets, fan regulator as required for one light point controllrd by one switch.( Note :- The cost of cutting chases in stone masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate of the concealed wiring.

All as per item No. 148 here-in-before but one fan point controlled by one switch

All as per item No. 148 here-in-before but exhaust fan point controlled by one switch

All as per item No. 148 here-in-before but one angle holder point controlled by one switch.

All as per item No. 148 here-in-before but One socket outlet 6 amp controlled by one switch on the same board with other switches.

All as per item No. 148 here-in-before but One socket outlet 6 amp controlled by one switch on indepdendent board.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes with modular white cover plate with frame for one socket point 16 Amps controlled by one switch on indepdendent board.

S&F angle holder 6A, 240V insulated polycarbonate body with back plate complete.

S&F switch modular 1 way 6 Amps, 230 volts, 1 module. Make : Legrand Mylink ™ mechanisms, Cat No : 675501 or equivalent as approved by GE

S&F modular socket 6 Amps, 2/3pin combined 2 module AC 230 volts.Make : Legrand Mylink ™ mechanisms , Cat No 6755 50 or equivalent as approved by GE

S&F modular switch 1 way 16 Amps, 230 volts, 1 module.Make :Legrand Mylink ™ mechanisms, Cat No : 6755 11 or equivalent as approved by GE

S&F modular socket 6/16 Amps, 2/3pin combined 2 module AC 230 volts. Make : Legrand Mylink ™ mechanisms Cat No : 6755 55 or equivalent as approved by GE

S&F modular fan regulator 120 watts, 2-module AC 230 Volts. Make : Legrand Mylink ™ mechanisms Cat No : 6755 31 or equivalent as approved by GE

S&F ceiling rose 3 plates polycarbonate body complete. Make: Ancher Penta Cat No : 39017 or equivalent as approved by GE

S&F modular whiter cover plate with frame and metal flush box 1/2 module. Make : Legrand Mylink ™ mechanisms Cat No: 6755 61-62 or equivalent as approved by GE

S&F modular white cover plate with frame and metal flush box 3 module. Make : Legrand Mylink ™ mechanisms Cat No : 6755 63 or equivalent as approved by GE

S&F modular whiter cover plate with frame and metal flush box 4 module.Make : Legrand Mylink ™ mechanisms Cat No : 6755 64 or equivalent as approved by GE

S&F modular white cover plate with frame and metal flush box 6 module. Make : Legrand Mylink ™ mechanisms Cat No : 6755 66 or equivalent as approved by GE

S&F modular white cover plate with frame and metal flush box 8 module. Make : Legrand Mylink ™ mechanisms Cat No : 6755 67 or equivalent as approved by GE

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories size 2X4 sqmm + 1X4 sqmm earth wire in 20 mm dia conduit.and terminnated in power socket, DBs, panel etc all as directed.

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories size 4X6 sqmm + 2X6 sqmm earth wire in 25 mm dia conduit and terminnated in power socket, DBs, panel etc all as directed.

S&F 20 amp, single pole and neutral socket outlet with 2 pole and earthy, metal enclosed plug top in power coated CRCA steel sheet enclosure recess mounted with cchained metal cover for socket outlet with and including one number single pole 'C' series MCB 16 amp as required. Make- Legrand/Hager/Schneider as approved.

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised iron 4.0 mm earth lead wire by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 40 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4.0 mm galvanised iron wire

S&F in replcement MCB distribution board, powder coated, TPN , 415 volts, 4 ways,CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required. Make:-Legrand Cat No: 5076 or equivalent as approved by GE

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Single pole 6 to 32 amp. Make - Legrand cat ref no 408587 to 408595 or equivalent as approved by GE

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Double pole 10 to 32 amp. Make - Legrand cat ref no 4086 14 to 4086 17 or equivalent as approved by GE

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of TPN 40 to 63 amp. Make - Legrand cat ref no 4086 59 to 4086 61 or equivalent as approved by GE

Supply & Laying, jointing testing & commissioning of XLPE LT cable PVC insulted PVC sheathed armoured stranded aluminium conductor heavy duty 1100 volt grade cable including gland lugs laid in trenches or drawn though GI pipe complete of Size 16 Sqmm 4 core.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out in hard/dense soil.

Returning, filling in , including spreading , leveling watering and well raming in layers n.exc. 25 cm, with soil.

Removing excavated material not exceeding 50 m and depositioning where directed at a level not exceeding 1.5 m above the starting point in Soft/hard dense soil

Supply & laying unrenforcement precast concrete cable cover class LV type I size 250mmx150mmx40mm complete

Supply spreading dry river sand cushioning to UG cable including leveling & hand punning etc complete.Note : for the purpose of payment only punned thikness will be measured.

M&L for plain cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate for couping of poles including use and waste of form work for fair finished surface.

M&L for GI Tubing medum grade, lay in trench or fix on wall/pole including suitable size clamp with nut & bolt of size 40 mm bore

S&F in repair LED (1.2M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens/21 watt at a minimum system efficacy of 2000 lumen per 21 watt and total power consumption not more than 21 watt including driver. It has a rated system life time of 25000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete. Make : Philips Cat Part No : BN 021LED 10S 6500 /4000 GR S1 or equivalent as approved by GE

S&F in repair LED (0.6 M)/ 2ft smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 1150 lumens/10 watt at a minimum system efficacy of 1150 lumen per 10 watt and total power consumption not more than 10 watt including driver. It has a rated system life time of 25000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete. Make : Philips Cat Part No : BN 021C LED 20 PSU CDL /NW GR or equivalent as approved by GE

S&F LED bulk head fitting 6.5 watt IP 65 & IK 08 with pressure die cast aluminium housing & polycarbonate diffuser duly pre wired connection with 0.75 Sqmm PVC insulated & sheathed three core flexible multi stranded copper conductor cable all as per Philips Cat Ref No. WT 202W LED 6S PSU NW S2 PC or equivalent as approved by GE

S&F in replacement 10 watt LED T -lamp B-22 base (warm white/golden yellow) 1000 lumens, height 8.0 cm width 20.5. Make : Make : Philips Part No 9290018611 or equivalent as approved by GE

Supply and fix eahaust fan MS body AC 230 volts of 300 mm sweep with standard accessories including providing 04 Nos fasteners 10mmx75mm long in existing wall and making suitable hole in wall complete. Make : Havells Model : Ventilair DSP or equivalent as approved by GE

Supply and fixing water heater of 25 liter capacity BEE star rating 5 in approved color, heating element 2.0 KW adjustable temperature setting knob for temparture settings between 25 degree to 75 degree centigrade, outer tank made of non metallic engineering plastic, inner tank made of extra thick superior cold rolled steel provided with high density PUF insulation including 15mm bore 450mm long flexible PVC pipe connection for cold water supply and 15mm bore 450mm long chromium plated metallic flexible pipe connection for hot water supply complete.

M&L for complete removal of existing treatment of old external plastered surface of walls and applying priming (Seal-o-Prime) on plastered surface and two coat of weather proof exterior emulsion paint (Weather coat smooth) complete all as specified and directed.

M&L for two coat of weather proof exterior emulsion paint (Weather coat smooth) over a coat of priming (Seal-o-Prime) on new plastered surface complete all as specified and directed.

Schedule of Credit

Deep Construction Company

UNIVERSAL INFRAPROJECT PVT LTD

S.R.Enterprises

Smita Constructions