Construction of Central Administrative Building at Shirur Anantpal Tq.Shirur Anantpal District Latur

Amount

PART – A (Work Portion)

i) Civil Work

ITEM No. 1 :- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material with all lifts and leads beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etcetera complete. (Lift upto 1.5 metre)

ITEM No. 2 :- Excavation for foundation in hard murum including removing the excavated material with all lifts and leads beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etcetera complete. (Lift upto 1.50 metre)

ITEM No. 3 :- Excavation for foundation in Hard murum and boulders including removing the excavated material with all lifts and leads, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etcetera complete. (Lift upto 1.5 metre)

ITEM No. 4 :- Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material with all lifts and leads beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth / murum, ramming, watering including shoring and strutting etcetera complete. (Lift from 1.5 metre to 3.0 metre)

ITEM No. 5 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. (Material including all lead and lifts)

ITEM No. 6 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-15 of trap/ granite / quartzite / gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood / steel formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etcetera complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etcetera (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.) (Material including all lead and lifts)

ITEM No. 7 :- Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite / quartzite / gneiss metal for reinforced cement concrete work in foundations like raft, strip foundations, grillage and footings of reinforced cement concrete columns and steel stanchions etcetera including bailing out water, formwork, cover blocks, laying / pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etcetera complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

ITEM No. 8 :- Providing and laying Cast in situ / Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for reinforced cement concrete columns as per detailed designs and drawings or as directed including centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etcetera complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 9 :- Providing and laying Cast in situ / Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying / pumping, compaction and roughening the surface if special finish is to be provided and curing etcetera complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 10 :- Providing and laying Cast in situ / Ready Mix cement concrete M-25 of trap/ granite / quartzite / gneiss metal for reinforced cement concrete slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, compaction, finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etcetera complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 11 :- Providing and laying Cast in situ / Ready Mixcement concrete M-25 of trap/ granite/ quartzite / gneiss metal for reinforced cement concrete chajja as per detailed design and drawings including centering, formwork, cover blocks, laying / pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 12 :- Providing and laying Cast in situ / Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete pardi of required thickness including centering, formwork, cover blocks, laying / pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 13 :- Providing and laying Cast in situ / Ready Mix cement concrete in M-25 of trap / quartzite / granite / gneiss metal for reinforced cement concrete Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying / pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etcetera complete. (Excluding reinforcement, including cover block). (Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etcetera) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 14 :- Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for reinforced cement concrete pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etcetera as per detailed designs, drawings and schedules including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (Material including all lead and lifts) (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 15 :- Providing expansion joints in reinforced cement concrete framed structure (interior column) with plain premoulded filler 25 millimetre thick including fixing T.W. battens on both faces and finishing as directed etcetera Complete.

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 16 :- Providing expansion joints in reinforced cement concrete framed structure (exterior Columns) with plain premoulded filler 25 millimetre thick and 3 millimetre thick alluminium plate, hold fast, fixing T.W. battens on internal face, finishing etcetera complete as directed.

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 17 :- Providing expansion joints in reinforced cement concrete framed structure (at floor level) with premoulded filler 25 millimetre thick and 3 millimetre thick aluminium plate as required, bitumen poured filler and fixing T.W. battens on rear faces etcetera complete as directed.

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 18 :- Providing expansion joints in reinforced cement concrete framed structure (at terrace level) with premoulded filler 25 millimetre thick and 3 millimetre thick aluminium plate as required, bituminous poured filler, fixing lead, flashing on upper side and T.W. battens on inner face finishing etcetera complete as directed. (Second Floor)

ITEM No. 19 :- Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etcetera complete. (Material including all lead and lifts)

ITEM No. 20 :- Filling in plinth and floors with approved excavated material in 15 centimetre to 20 centimetre layers including watering and compacting etcetera complete. (Material including all lead and lifts)

ITEM No. 21 :- Filling in plinth and floors with contractors material / brought from outside and approved by Engineer in charge in layers of 15 centimetre to 20 centimetre including watering and compaction etcetera complete. (Material including all lead and lifts)

ITEM No. 22 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper. (Material including all lead and lifts)

ITEM No. 23 :- Providing soling using 80 millimetre size trap metal in 15 centimetre layer including filling voids with Crushed sand /grit, ramming, watering etcetera complete. (Material including all lead and lifts)

ITEM No. 24 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying / pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.) (Material including all lead and lifts)

ITEM No. 25 :- Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 26 :- Providing Second class fly ash brick masonry with conventional / I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of two bars of 6 millimetre diameter / two hoop iron strips 25 millimetre X 1.60 millimetre at every third course, properly bent and bounded at ends scaffolding raking out joints and watering etcetera complete. (Material including all lead and lifts)

A) First Floor

B) First Floor

C) Second Floor

ITEM No. 27 :- Providing and laying Cast in situ / Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including centering, formwork, cover blocks, laying/pumping, compacting, curing, finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 28 :- Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300 millimetre X 40 millimetre X 5 millimetre with oil painting, etcetera complete. (Material including all lead and lifts)

ITEM No. 29 :- Providing and fixing mild steel grill work for windows, ventilators etcetera 20 kilogram per square metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 30 :- Providing and fixing chicken mesh of 22 gauge, with about 30 centimetre width at the junction of reinforced cement concrete members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete or burnt brick masonry and or tying by binding wire etcetera complete. (Material including all lead and lifts)

ITEM No. 31 :- Providing and applying two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 32 :- Providing internal cement plaster 12 millimetre thick in single coat in cement mortar 1:5 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 33 :- Providing neeru finish to plastered surfaces in all positions including scaffolding and curing etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 34 :- Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimetre thick in cement mortar 1:4 using waterproofing compound at 1 kilogram per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 35 :- Providing and applying Texture plaster with finishing with Purli / Rustic texture material (with texture material of Asian / Renava / Nitco / Temtex or equivalent company make) in 3 to 4 millimeter thickness on previously finished plastered surface, including Plaster Groove 6 millimetre thickness or Tape Grooves 35 to 45 millimetre thickness or as required, in all position including preparing the surface scaffolding etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 36 :- Labour charges for providing groove in external plaster having width and spaced as directed by Engineer in charge etcetera complete.

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 37 :- Providing patti/ band 100 millimetre wide on plastered surface 12 millimetre to 15 millimetre thick in C.M. 1:3 line and level including neat finishing scaffolding curing etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) Second Floor

ITEM No. 38 :- Providing internal cement plaster 20 millimetre thick in two coats in cement mortar 1:3 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etcetera complete. (Material including all lead and lifts)

ITEM No. 39 :- Providing fine cement finish 1.5 millimetre thick over green plaster surface including scaffolding curing etcetera complete. (Material including all lead and lifts)

ITEM No. 40 :- Providing and applying a base coat comprising of 1 Kg Polydee-MC and 1 Kg fresh cement after wetting the surface followed by drying the surface for 2 days, apply primer coat of TP-40 and after drying, applying Polydee-11 two component (mixing ratio 2 A : 1 B) ) Antibacterial food grade coating inside drinking water tank in two coats with time interval of minimum 8 hrs. covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) Second Floor

ITEM No. 41 :- Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12 millimetre bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound at the rate of 1 kilogram for per bag of cement laying brick bat coba of required thickness in cement mortar 1:5 with waterproofing compound 1 kilogram per bag of cement grouting and finishing the top layer with 20 millimetre thick brick bedding in cement mortar 1:3 with waterproofing compound 1 kilogram per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years guarantee on requisite stamp paper including curing etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 42 :- Providing and laying vitrified matt finish tiles having size 590 millimetre to 605 millimetre X to 605 millimetre of 8 to 10 millimetre thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etcetera complete. a) Flooring (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 43 :- Providing and laying vitrified matt finish tiles having size 590 millimetre to 605 millimetre X to 605 millimetre of 8 to 10 millimetre thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etcetera complete. b) Skirting (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 44 :- Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 millimetre to 20 millimetre thick on bed 1:6 cement mortar including cement floats striking joints, pointing in cement mortar 1:3 curing and cleaning etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 45 :- Providing and fixing machine cut machine polished 18 millimetre to 20 millimetre thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 46 :- Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 millimetre thick for door frame/ dado/ window boxing etcetera on cement mortar 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 47 :- Providing and laying ceramic tiles having size 30 centimetre x 60 centimetre confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etcetera complete.

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 48 :- Providing and laying Antiskid Ceramic tiles of approved quality of size 30 centimetre x 30 centimetre and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 49 :- Providing 25 millimetre to 30 millimetre thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etcetera fixing in cement mortar 1:3 curing and cement etcetera complete. a) One side polish. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

B) Second Floor

ITEM No. 50 :- Providing 25 millimetre to 30 millimetre thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etcetera fixing in cement mortar 1:3 curing and cement etcetera complete. b) Both side polish (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 51 :- Providing and fixing heavy duty inter locking concrete Rubber mould glossy paving blocks of 80 millimetre thickness of having a strength of 400 kilogram per Square centimetre of approved quality and shape on a bed of crushed sand of 25 to 30 millimetre thick including skirting joints and cleaning etcetera complete. (using 100% crushed sand)

ITEM No. 52 :- Providing and laying in situ cement concrete M-30 with tremix treatment for 200 millimetre thickness for flooring with groove cutting of 4 millimetre wide and 20 millimetre deep with necessary refilling with bitumen etcetera complete.

ITEM No. 53 :- Supply and Fixing of Rock / Stone Finished outdoor vitrified flooring Tiles 20 millimetre thick and required width wide in plain pattern including Cement float, filling joints, with neat cement slurry, Natural sand, curing and cleaning complete. with prior approval of concerned Superitending Engineer. (Material including all lead and lifts)

ITEM No. 54 :- Providing and fixing Country teak wood Four leaf paneled shutters, 35 millimetre thick style and rail and 25 millimetre thick panels without ventilator as per detailed drawing excluding the door frame, stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats complete. (Material including all lead and lifts)

ITEM No. 55 :- Providing and fixing 34 millimetre thick moulded door shutter consisting of solid core single leaf flush door of 30 millimetre thickness lipped with 15 millimetre ( 5 millimetre X 3 ) thick X 30 millimetre width on one style and top rail and 10 millimetre (5 millimetre X 2 ) thick X 30 millimetre width on other style and bottom rails. The inner panels laminated with 2 millimetre thick termite proof, water proof and fire resistant moulded PVC sheet with 2,4,6 design in different plain and /or prelim colours on one side after routing the moulded design on flush doors and 2 millimetre plain and /or pre lam PVC on other side using rubber adhesive on flush door and solvent cement adhesive on the PVC lipping etcetera as per direction of Engineer in charge and manufacturers specification and drawing etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 56 :- Providing and Fixing 30 MILLIMETRE thick BOTH SIDE PRELAMINATED SOLID PANEL PVC DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 guage thickness and, size 19 X 19 millimetre for styles and 15 X 15 millimetre for the top and bottom rails, M.S. frame shall have a coat of metel primer of approved make and manufacture. M.S frame shall be covered with heat mouled PVC 'C' channel made from 5 millimetre (+/0.25) thick prelaminated sheet of density 600 kg/cbm, of size 30 millimetre thickness 70 millimetre width out of which 50 millimetre shall be flat and 20 millimetre shall be tapered in 45 angle on either side forming stiles ? and 5 millimetre thick, 95 millimetre wide PVC sheet out of which 75 millimetre shall be falt and 20 millimetre shall be tapered in 45 on the inner side to form top and bottom rail and 115 millimetre wide PVC sheet out of which 75 millimetre shall be falt and 20 millimetre shall be tapered on both sides to form lock rail. Top, bottom and lock rail shall be provided either side of the panel. An additional 5 millimetre (+/0.25) thick PVC strip of 20 millimetre width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5 millimetre (+/0.25) thick PVC sheet to be fitted inside the Mild Steel frame welded/ sealed to the styles and rails with 5 millimetre (+/0.25) x 30 millimetre PVC sheet beading on either side and joined together with solvent cement adhesive etcetera, 10 millimetre thickness (5 millimetre (+/0.25) X 2 numbers ) 20 millimetre wide cross PVC sheet as gap insert for the rail and bottom rail. Door to be fixed to frames with 3 numbers M.S. powder coated but hinges of size 100 millimetre X 25 Millimetre X 2 millimetre using 32 millimetre long steel screws drilled suitable to pass through both the walls of the M.S. tube, other hardwares should be fixed with 19 X 6 millimetre size steel screws including fixture fasting, complete as per direction of engineer in charge. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 57 :- Providing and fixing ISI marked double swing flush door shutters conforming to IS :2202 (Part I) Non-decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters, 30 millimetre thick including ISI marked Stainless Steel L hinges with necessary screws Fittings & Fixtures per leaf SS kick plates on both sides of the door of 300 millimetre height Heavy Duty satin finish butt SS Hinges (100 millimetre X 75 millimetre X 3 millimetre in size) -4 numbers, SS finished lever handle with mortise lock- 1 One Number Floor spring- 1 One Number 100 millimetre x 100 millimetre safety glass at the specified location.

A) Ground Floor

B) First Floor

ITEM No. 58 :- Sliding Window- 3 Track (2 Glass shutter + 1 flymesh) of approved make with DGU, providing and fixing of Sliding Window- 3 Track (2 Glass shutter + 1 flymesh ). For details refer to Specifications and as directed by Engineer in charge. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 59 :- Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 X 38 millimetre X 1.22 millimetre box type, 5 millimetre thick sheet glass louvers, of approved quality etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 60 :- Providing and fixing Mild Steel grill door 24 kilogram per square metre of various size as per detailed drawings without hot dip coating, iron fixtures and fastenings and 3 coats of oil painting etcetera. (Material including all lead and lifts) (Eighth Terrace Floor)

ITEM No. 61 :- Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 millimetre diameter and vertical pipe of 38 millimetre diametre at 0.60 metre centre to centre or as required and horizontal pipes of 25 millimetre diametre in three rows, all pipes of 2 millimetre thick including buffing, fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 millimetre diameter above newel post of 75 millimetre diameter etcetera complete (Prior approval of sample and brand by Executive Engineer is necessary before use) (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 62 :- Providing and applying interior wall finish luster of approved make on internal wall surface as detailed below Scrapping the surface with emery paper and wipe clean wall primer with brush with mineral turpentine with brush 8 to 10% and oil 15 to 20% with roller and allowing to dry for a period 6 to 8 hours, wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours, Scrapping with Emery paper 180 and wipe clean. Applyingwall primer with brush with mineral turpentine 8 to 10% and oil 15 to 20% with roller Scrapping Emery paper 320 and wipe clean, interior wall finish luster 1st coat with brush/rubber/spray with mineral turpentine 7 to 9% and Oil with roller 19 to 21% After 8 hours of activity Applying 2nd coat or wall finish Lustre with mineral turpentine 7 to 9 % with brush and Oil with roller 19 to 21% after allowing dry for the period of 6 to 8 hours activity. (With prior approval of Superintending Engineer). (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 63 :- Providing and applying two coats Apex Ultima Puranature Anti-Pollution or equivalent approved brand, paint should decomposes organic substances and inorganic gases (NOx, VOC’s, CO, SOx, formaldehydes, etcetera) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide and Absorbs CO2 (4.8 kilogram per 15 litres). Plaster crack should be filled by Acrylic base Crack seal / Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty should be given by the Manufaturer the work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 64 :- Providing soak pit of size 120 centimetre x 120 centimetre x 120 centimetre including excavating and filling with brick-bats. (Material including all lead and lifts)

ITEM No. 65 :- Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etcetera as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etcetera complete. (Second Floor)

ITEM No. 66 :- Supply and Installation of Dpi Flux translucent roof with standing seam multicell polycarbonate panel system. The system with complete assembly of co extruded UV protected multicell panels incorporated into a complete system. Co-extruded UV protected polycarbonate panel system of minimum 22 millimetre thick of 1200 millimetre (minimum) width with angular daylighting concept. Panels shall have minimum seven layers in a truss bridge design for higher flexibility and strength. Panels with opaque and translucent clear combination as per required lux level and design requirements with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall have an additional IR Blocking features for enhance thermal comfort. Panels shall be manufactured with vertical standing seam at both sides of the panel. Panels shall be fixed on Purlin with snap on connectors with double tooth grip lock locking mechanism and will be secured on MS structure (will be paid Separately) with a continuous aluminium I Beam holding the base of the standing seam along the length of the panel and fixed with purlin with self-drilling hex head screws offering best stability with a pull-out load of minimum 21000N (21KN) tested as per ISO 6892:1998 and IS 1608: 2005, as per design requirement. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a minimum of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not be more than 1.9 W/m2K as per EN ISO 10077-2:2018. Panel shall be with additional End cap / Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing and direction of the engineer in charge. Colour: As per approval The 22 millimetre thick panels shall be used for a roofing height of upto 55 metres. (Material including all lead and lifts) (Second Floor)

ITEM No. 67 :- Providing and fixing 90 centimetre x 60 centimetre Granite plate engraving 10 centimetre height letter, figures including painting the letters / figures with approved colour and shade complete. (Material including all lead and lifts)

ITEM No. 69 :- Providing and constructing Brick Masonry Inspection Chamber 60 centimetre x 45 centimetre x 90 centimetre including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with reinforced cement concrete Cover medium duty 140 kilogram with frame etcetera complete. (Material including all lead and lifts)

ITEM No. 70 :- Providing and constructing Brick Masonry Inspection Chamber 90 centimetre x 45 centimetre x 90 centimetre including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with reinforced cement concrete Cover medium duty 140 kilogram with frame etcetera complete. (Material including all lead and lifts)

ITEM No. 71 :- Providing and fixing Poly Vinyl Chloride Rain water pipes of 110 millimetre outer diameter and having wall thickness of 2.2 to 2.7 millimetre confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, including fixing the pipe on wall using approved wooden cleats projecting 25 millimetre to 40 millimetre from face of wall a fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on Cement concrete or masonry blocks, including necessary scaffolding and maintenance for 3 years for any leakages or dislocations of pipes, all the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etcetera complete. (The contractor shall give 3 years guarantee bond for payment). (Material including all lead and lifts)

ITEM No. 73 :- RWH - Recharge Pit Providing and constructing recharge pit of 2.0 metre deep and 1.0 metre diametre of pre-cast Reinforced cement concerete rings with 6.5" diametre X 25 metre deep borewell at the floor of recharge pit including installation of combination of solid / perforated PVC casing pipe wrapped around with netlon mesh including 300 millimetre thick side filling around outside of Reinforced cement concete rings (annular space) with 40 millimetre size boulders including filling of recharge pit upto 0.5 metre depth with 25-75 millimetre clean washed gravels from bottom up followed by 0.5 metre depth of 10-25 millimetre of clean washed stones followed by 0.5 metre of washed river fine aggregate ( natural sand / crushed sand VSI grade finely washed etcetera) including netlon mesh between each gravel / fine aggregate (natural sand / crushed sand VSI grade finely washed etcetera) media layer including covering with Reinforced cement concrete slab, manhole frame and cover, PVC rings, PVC end-caps, fittings etcetera including arrangement for inlet and outlet pipe excavation and back filling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge. (Material including all lead and lifts)

ITEM No. 74 :- Providing and fixing on walls/ ceiling/ floor 15 millimetre diameter CPVC pipe with necessary fittings, remaking good the demolished portion etcetera complete including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete. (Material including all lead and lifts)

ITEM No. 75 :- Providing and fixing on walls / ceiling / floor 25 millimetre diameter CPVC pipe with necessary fittings, remaking good the demolished portion etcetera complete, including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete. (Material including all lead and lifts)

ITEM No. 76 :- Providing and fixing on walls /ceiling/ floor 40 millimetre diameter CPVC pipe with necessary fittings, remaking good the demolished portion etcetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete. (Material including all lead and lifts)

ITEM No. 77 :- Providing and laying in trenches 50 millimetre daimetre CPVC pipe including necessary excavation, fittings. Refilling trenches etcetera complete, including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete. (Material including all lead and lifts)

ITEM No. 78 :- Providing and fixing screw down for 40 millimetre diameter wheeled stop tap of brass including necessary sockets/union nut complete. (Material including all lead and lifts)

ITEM No. 79 :- Providing and fixing screw down for 25 millimetre diameter wheeled stop tap of brass including necessary sockets/union nut complete. (Material including all lead and lifts)

ITEM No. 80 :- Providing and fixing Orissa Pan of size 580 X 445 X 260 millimetre with approved make flush valve including trap, C.I. soil and vent pipe upto outside face of wall including 100 millimetre diametre Cast Iron plug, bend and necessary pipe connection, etcetera complete as directed by Engineer in charge. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 81 :- Providing and fixing white european type wall-hung, Size 360 millimetre x 360 millimetre x 575 millimetre with flush valve having flow rate up to 6.0 Litre per Minute of Jaquar/Cera/Hindware /Perryware or equivalent make including PVC soil pipe, vent pipe upto outside face of wall, 100 millimetre diametre PVC plug bend inlet pipe all fittings, cutting and making good walls, floors etcetera as directed by Engineer in charge. (Make shall conform to manufacturer's Green product and shall got approved from the Engineer in charge.) (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 82 :- Providing and fixing wall-hung white wash basin of size 470 X 575 X 190 millimetre of approved make half pedestal, pillar cock, C.P. Angular stop cock, long thread continental including Stainless Steel bottle trap of having necessary pipe connections up to the outside face of the wall etcetera complete. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 83 :- Providing and fixing C.P. 2 Way BIB cock with wall flange of approved make including necessary sockets/ union nut etcetera complete as directed by Engineer in charge. (Material including all lead and lifts)

ITEM No. 84 :- Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets / union nut etcetera complete as directed by Engineer in charge. (Material including all lead and lifts)

ITEM No. 85 :- Providing and fixing white glazed urinal of series with Pressmatic auto closing valve of having 32 millimete diameter Poly Vinyl Chloride flush pipe with fitting and flushing of approved make and arrangement including lead soil pipe, lead trap and soil pipe connection upto the outside face of wall etcetera complete as directed by Engineer in charge. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 86 :- Providing and fixing sink cock with regular swinging spout (Wall Mounted Model) with wall flange with approved make incluidng other necessary fitting, etcetera complete as directed by Engineer in charge. (Material including all lead and lifts)

ITEM No. 87 :- Providing and fixing stainless steel sink of size 600 x 510 x 200 millimetre including coupling, outlet pipe, elbow and other necessary fitting, finishing etcetera complete. (Material including all lead and lifts)

ITEM No. 88 :- Providing and Fixing half turn 25 millimetre diameter gun metal flushing cock including all accessories etcetera complete. (Material including all lead and lifts)

ITEM No. 89 :- Providing and fixing 450 millimetre X 550 millimetre size superior type Belgium mirror with 16 millimetre diameter nickel plated towel rod etcetera complete. (Material including all lead and lifts)

ITEM No. 90 :- Providing and fixing 100 millimetre diametre stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etcetera complete. (Material including all lead and lifts)

ITEM No. 91 :- Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres. (Material including all lead and lifts) (Second Floor)

ITEM No. 92 :- Providing and fixing 10 centimetre PVC nahani trap with grating etcetera complete. (Material including all lead and lifts)

ITEM No. 93 :- Providing and fixing in position UPVC ultra violet stabilized 110 millimetre outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etcetera complete. (Material including all lead and lifts)

ITEM No. 94 :- Providing and laying in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for reinforced cement concrete work in foundations like raft, strip foundations, grillage and footings of reinforced cement concrete columns and steel stanchions etcetera including bailing out water, formwork, laying / pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etcetera complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

A) Building Work

B) Water Storage Tank

ITEM No. 95 :- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for reinforced cement concrete columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying / pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etcetera complete, (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.) (Material including all lead and lifts)

ITEM No. 96 :- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for reinforced cement concrete beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying / pumping, compaction and roughening the surface if special finish is to be provided and curing etcetera complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

ITEM No. 97 :- Providing and fixing bituminous pad 25 millimetre thick for expansion joints in retaining wall, compound wall etcetera complete. (Material including all lead and lifts)

ITEM No. 98 :- Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etcetera as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etcetera and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etcetera complete. (Material including all lead and lifts)

ITEM No. 99 :- Providing internal cement plaster 20 millimetre thick in two coats in cement mortar 1:5 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etcetera complete. (Material including all lead and lifts)

ITEM No. 100 :- Providing and applying 2 coats of 100% Pure acrylic low VOC and APEO & HCHO free water based paint of approved colour that belongs to class 1 flame spread resistance of approved make Paint should provide durable and long lasting silk finish with a high crack tolerance of upto 1 millimetre, paint should have an oustanding washability with high resistance to wide range of bacteria and fungus. Paint has to be applied on smooth and uniform surface prepared by an acrylic copolymer low VOC & Odour putty. This surface should be primed with water based low VOC Primer. The work activity should cover all aspects of applying paints from surface preparation as directed by Engineer in charge. (Material including all lead and lifts)

ITEM No. 101 :- Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 metre and spreading for embankment or stacking as directed. By Mechanical Means.

ITEM No. 102 :- Conveying materials obtained from road cutting including all lifts, laying in layers of 20 centimetre to 30 centimetre breaking clods, dressing to the required lines, curves, grades and section, watering and compacting to not less than 97% of standard proctor density for a lead of 300 metre to 500 metre inclusive, from the site of excavation to the site of deposition as directed.

ITEM No. 103 :- Supplying hard murum / kankar at the road side, including conveying with all leads and stacking etcetera complete as directed by Engineer in charge. (Material including all lead and lifts)

ITEM No. 104 :- Spreading hard murum/ soft murum/ gravel or kankar for side width complete. (Material including all lead and lifts)

ITEM No. 105 :- Compacting the hard murum side widths including laying in layers on each side with Vibratory roller including artificial watering etcetera complete.

ITEM No. 106 :- Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with Vibratory roller to the required density. By Mechanical Means- Grading I (Using Screening Type A (13.2) millimetre Aggregate) (Material including all lead and lifts).

ITEM No. 107 :- Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 millimetre, cement content not to be less than 150 kilogram per cubic metre, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor / by suitable means as approved by Engineer-in-charge, compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etcetera complete. (Material including all lead and lifts)

ITEM No. 108 :- Providing and laying in situ cement concrete M-30 with tremix treatment for 200 millimetre thickness for Concrete Road is including laying plastic sheet for 125 micron thickness with groove cutting of 4 millimetre wide and 20 millimetre deep with necessary refilling with bitumen (excluding reinforcement) with Natural sand etcetera complete. (Material including all lead and lifts)

ITEM No. 109 :- Preparing Instant Lawn :- Excavating the ground to a requirsd depth of 20 centimetres, removing and conveying unwanted stuff to a required distance as directed. Filling fresh garden soil / silt and manure in excavated area in 3:1 proportion to a height of 20 centimetres mixing garden soil and manure thoroughly, well leveling, with required slope, light watering on previous night, rolling on surface, fixing readymade lawn truf, rolls or slabs of required variety as directed, ramming of it for proper fixing and maintaining till well established by watering, weeding, clipping or moving etcetera complete. (Material including all lead and lifts)

ITEM No. 110 :- Rose Plant :- Excavating pit with size 0.30 x 0.30 x 0.30 metre removing and conveying unwanted stuff to a required distance as directed. Filling the pit with fresh garden soil and manure in 3:1 proportion to a height of 30 centimetre, mixing garden soil and manure, throughtly well, levelling, watering on previous night, planting 40 to 50 centimetres height healthy plants of required rose variety maintaining till well established by watering weeding, stirring, prunning, replacing the casualties etcetera complete. (Material including all lead and lifts)

ITEM No. 111 :- Planting Large flowing / shady trees :- (minimum height to 1 metres) - Digging pit with size 0.9 metre X 0.9 metre X 0.9 metre removing and conveying unwanted stuff to a required as distance as directed. Filling the pit with approved exavated material upto hight of 0.3 metre and remaining height of 0.6 metre fresh garden soil and murum in 3:1 preparation. Mixing soil and murum thoroughly well levelling, as directed, watering previous night, planting two to three year old healthy trees sapling as per specification, maintaing till well established by watering, wedding, stirring of soil staking replacing of casualties etcetera complete + Planting Trees on Soft / Hard surface (Individual) : Filling of Red Hill Earth, Cow Dung Manure and good earth from excaveted pit in the excavated pits mixing in 2:1:1 proportion, watering and providing well grown trees with minimum average girth of 2" and minimum height of 10' above finished level after plantation of specified variety, at desired location and at specified distances. Achieving finished grade level. Planting the tree with appropriate anchoring, eveling the top soil surface as specified after plantation, staking to balance the tree. Including transport to the site & planting, preparation of free basin, watering & maintaining for 1 month after completion of plantation and replacement of casualties till 1 month. (Material including all lead and lifts)

ITEM No. 112 :- PLANTING SMALL AND MEDIUM SIZE ORNAMENTAL / FLOWERING PLANT - Digging pit with size 0.6 metre x 0.6 metre x 0.6 metre removing and conveying unwanted stuff to a required distance as directed. Filling the pit with fresh garden soil and farm Yard manure upto a height of 0.60 m with fresh garden soil and manure in 3:1 proportion. Mixing soil and manure thoroughly well, leveling as directed, watering previous night planting one to two year old healthy trees sapling as per specification. Maintaining till well established by watering weeding stirring of soil replacing of casualties etcetera casualties etcetera complete. (Material including all lead and lifts).

ITEM No. 113 :- PLANTING CLIPPED HEDGE : Excavating the ground to the required depth of 30 centimetre and removing and conveying unwanted stuff to the required distance as directed. Filling the excavated part with fresh soil and manuar in excavated area in 3:1 proportion to a height of 30 centimetre mixing, levelling, watering the same planting unrooted cuttings distance between two rows and between two cutting will be 25 centimetre and watering and maintaining till well established by watering weeding, stirring, prunning, replacing the casualties etcetera complete.

ITEM No. 114 :- Excavation for catch / side water gutter in all sorts of soils to the specified section including stacking the excavated stuff in a regular bund and disposing of unsuitable or excess stuff as directed all sorts of soils.

ITEM No. 115 :- Providing cast in situ / ready mix M20 grade cement concrete for head walls of CD work / retaining walls etcetera including necessary form work, compaction, finishing and curing etcetera complete. (with reversible drum type mixer/ concrete batch mix plant (pan mixer) With fine aggregate (Crushed sand VSI Grade.) Cement 4.05 bags per cubic metre) (Material including all lead and lifts)

ITEM No. 116 :- Providing and laying in situ / ready mix M-20 cement concrete of trap /granite /quartzite /gneiss metal for approach slab including compacting, finishing, curing etcetera complete. (excluding reinforcement) (with reversible drum type mixer/ concrete batch mix plant (pan mixer) with SCADA with fine agreegates of required specifications With fine aggregate (Crushed sand VSI Grade.), cement 5.90 bags per cubic metre) (Material including all lead and lifts)

ITEM No. 117 :- Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 450 millimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etcetera complete. (Material including all lead and lifts)

ITEM No. 118 :- Providing and laying Cast in situ / Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete pardi of required thickness including centering, formwork, cover blocks, laying / pumping, compacting, curing, finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.). (Material including all lead and lifts)

ITEM No. 119 :- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for reinforced cement concrete slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etcetera complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade.) (Material including all lead and lifts)

ITEM No. 120 :- Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 square metre per kilogram with two coat using Dr. Fixit or alike of chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etcetera complete. (Material including all lead and lifts)

ITEM No. 121 :- Providing and fixing 20 to 25 millimetre thick rough shahabad box type waterproofing for basement or underground floor on a base of Cement concrete 1:3:6, including sub base of 2.50 centimeter thick Cement mortar 1:3 with conceal, secrete (RMW), Algae proof or other alike waterproofing liquids, raking of joints upto 35 millimetre depth, filling the joints with 6 millimetre size crushed metal, hand grouting with cement slurry, curing and cleaning, with 7 years guarantee on court fee stamp of Rs. 100/- with ponding test etcetera complete. (excluding Cement concrete 1:3:6 base concrete ) (Material including all lead and lifts)

ITEM No. 122 :- Boring / drilling bore well of 150 millimetre diametre for casing / strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants and machinery required for the job, all complete as per direction of Engineer in charge, upto 90 metre depth below ground level. (Material including all lead and lifts)

ITEM No. 123 :- Providing and fixing UPVC casing pipe 180 millimetre diameter (6 Kilogram per centimeter2) (IS 4985-1988) complete.

ITEM No. 124 :- Yield testing by V notches etcetera complete as directed by Engineer in charge

ITEM No. 125 :- Providing and fixing PVC cap for 180 millimetre casing pipe etcetera complete. (Material including all lead and lifts)

ITEM No. 126 :- Providing and supplying in standard lengths Polythelene pipes (6 Kilogram per square centimetre – 63 millimetre diameter) (including all local and central taxes, octrai, inspection charges etcetera complete. (Material including all lead and lifts)

ITEM No. 127 :- Lowering, laying, jointing Polythelene pipes (6 Kilogram per square centimetre – 63 millimetre diameter) (including inspection charges etcetera complete. (Material including all lead and lifts)

ITEM No. 128 :- Providing and laying in walls / ceilings / floors 40 millimetre diameter medium grade having embossed as ISI Mark galvanised iron pipes of 3.68 kilogram per metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.

ITEM No. 129 :- Providing and laying in walls / ceilings / floors 25 millimetre diameter medium grade having embossed as ISI Mark galvanised iron pipes of 2.49 kilogram per metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete, including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.

ITEM No. 130 :- Providing and fixing frame work of anodised aluminium sections for suspended false ceiling consisting of aluminium T 50 millimetre X 40 millimetre weighing 0.39 kilogram per metre at 60 centimetres centre to centre and fixed with ( 15 x 15 millimetre) flanges weighing 0.119 kilogram per metre suspended on 6 millimetre diameter mild steel rod weighing 0.22 kilogram per metre fixed on wall and beams including rounding of the edges with aluminium T of 50 millimetre X 40 millimetre weighing 0.39 kilogram per metre etcetera including all labour etcetera complete.

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 131 :- Providing and fixing false ceiling of 10 to 12 millimetre thick decorative boards of fibrous plaster of paris including scaffolding if necessary all architectural work like mouldings, cornices, coves, domes, cups as per detailed drawings and three coats of spray painting to boards etcetera complete. (excluding frame work, runners and mild steel suspenders). (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 132 :- Providing Executive Table and side table and made out in 25 millimetre commercial plywood frame work with front side plywood covered top 25 millimetre +12 millimetre thick plywood confirming IS 303 finished with front, top Veneer Code Timex/ Bhutan Tuff 1645/ (3834) finish 25 millimetre X 25 millimetre moulding on both the edge and side table with 18 millimetre frame 2 work +12 millimetre ply for drawers, 2 coats of melamine polish finish etcetera inside to be finished whithegg white laminate and top of table covered with Same veneer including surface termite treatment all plywood’s, necessary hardware, labour etcetera complete as per drawing and design, as directed by Engineer in charge / Interior Designer. Rates are inclusive of all transportation, lead and all lift and labour charges includes maintains of 2 year and material got approved by Executive Engineer in charge before use. (First Floor)

ITEM No. 133 :- Providing Executive Table and side table made out in 25 millimetre commercial plywood frame work with front side plywood covered top 25 millimetre +12 millimetre thick plywood confirming IS 303 finished with front , top Veneer code Timex/ Bhutan Tuff ZR 110/ 26 (360/12) finish. 25 millimetre X 25 millimetre moulding on both the edge and side table with 18 millimetre frame 2 work +12 millimetre ply for drawers, 2 coats of melamine polish finish etcetera Inside to be finished with egg white laminate and top of table covered with same veneer including surface termite treatment all plywood’s, necessary hardware, labour etcetera complete as per drawing and design. As directed by Engineer in charge / Interior Designer. Rates are inclusive of all transportation, lead and all lift and labour charges includes maintains of 2 year and material got approved by Executive Engineer in charge before use.

A) First Floor

B) Second Floor

ITEM No. 134 :- Providing and Fixing table made up of BTC teak wood sections for framing unfinished wood size 75 X 200 millimetre to obtain 60 X 150 millimetre size as per architectural drawing and instructions also pedestal made up of 18 millimetre plywood ISI 303 and drawer made up of 12 millimetre plywood internally finished with external veneer/ matching laminate. Pedestal top is covered with Marino annex ST102 12 millimetre thick solid surface (coria) and inner legs resting on pedestal and front legs resting on ground in appropriate angle. legs and frame also finished with veneer Code Timex/ Bhutan tuff 4664 veneer and top is made up of 2 X 18 millimetre plywood with top ST 102, 12 millimetre coria and bottom finished with Timex/ Bhutan tuff 4664 veneer, All veneer surfaces melamine polishing including all hardware and labour etcetera complete, as directed by engineer in charge, rates are inclusive of all transportation, lead and all lift and labour charges includes maintains of 2 year and material got approved by Executive Engineer in charge before use.

A) First Floor

B) Second Floor

ITEM No. 135 :- Providing and Fixing table made up of BTC teak wood sections for framing unfinished wood size 75 X150 millimetre to obtain 70 X 125 millimetre size as per architectural drawing and instructions also pedestal made up of 18 millimetre plywood ISI 303 and drawer made up of 12 millimetre plywood internally finished with external veneer/ matching laminate. Pedestal top is covered with Marino annex ST102 12 millimetre thick solid surface (coria) and inner legs resting on pedestal and front legs resting on ground in appropriate angle. legs and frame also finished with veneer Bhutan tuff 415/29 veneer, and top is made up of 2 X 18 millimetre plywood with top ST 102, 12 millimetre coria and bottom finished with Bhutan tuff 415 / 29 veneer. All veneer surfaces melamine polishing including all hardware and labour etcetera complete as directed by engineer in charge rates are inclusive of all transportation, lead and all lift and labour charges includes maintains of 2 year and material got approved by executive engineer in charge before use.

A) First Floor

B) Second Floor

ITEM No. 136 :- Providing and fixing storage Unit box is made up of 18 millimeter plywood ISI303 and 12 millimeter ply TO BACK shelves in 18 millimeter ply, internally finished with 1 millimetre Textured Laminate, Shutter and drawers Outer face is finished with Veneer, Veneer code 110/26 ( 55/22) inner face is finished with same veneer which is out side or matching colour and design laminate. Profile handles are provided to drawers, including all material hardware, melamine polishing and labour as per Architects drawing and instructions and as directed by Engineer in charge etcetera rates are inclusive of all transportation, lead and all lift and labour charges includes maintains of 2 year and material got approved by Executive Engineer in charge before use.

A) First Floor

B) Second Floor

ITEM No. 137 :- Providing and fixing Free standing partition unit made up of 2 X 18 millimetre plywood (IS 303) frame at 0.60 metre centre to centre for box and covering by 18mm plywood (IS 303), In two parts one is hanging from slab which is fitted to slab and other part is from ground with gap between them. finished with Timex/ Bhutan Tuff 2271 veneer, also 12 millimetre toughened glass structure made for display, Veneer to be finished with melamine polishing as per Architect Drawing and instructions including hardware all labour as directed by Engineer in charge, rates are inclusive of all transportation, lead and all lift and labour charges includes maintains of 2 year and material got approved by Executive Engineer in charge before use.

A) First Floor

B) Second Floor

ITEM No. 138 :- Providing and fixing in position, Carpet more than 800+ gsm, made with100 % stain proof fibres of approved make along with 5 millimetre underlay as per Architectural and Acoustical Design and Instructions and complete in all aspects including all materials labour, finishing etcetera complete.

A) First Floor

B) Second Floor

ITEM No. 139 :- Providing and Arrangemnt of High Back, Synchronized Mechanism with Multiple Locking, Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Leatherite Upholstery. (Material including all lead and lifts)

ITEM No. 140 :- Providing and Arrangemnt of High Back Chair - tilt mechanism with multilocking, high density cushion on seat composite leather with metallic silver finish base and arms with P. U. castors gas lift for height adjustment. (Material including all lead and lifts)

A) First Floor

B) Second Floor

ITEM No. 141 :- Providing and Arrangemnt of Mid Back, Normal Syncro Mechanism, Fixed Armrest, Gaslift for Seat height adjustment, Standard 5-prong / Nylon Base with Leather Upholstery. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 142 :- Providing and Arrangemnt of Mid Back, ECO CTS Mechanism , Fixed Armrest , Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Fabric Upholstery. (Material including all lead and lifts)

A) First Floor

B) Second Floor

ITEM No. 143 :- Public Seating Chair - 3 Seater : Providing and fixing 3 seater Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish. (Material including all lead and lifts)

A) Ground Floor

B) First Floor

C) Second Floor

ITEM No. 144 :- Providing and supplying a set of three seater sofa ( 6 feet 6 inch ) two seater sofa ( 1050 X 680 X 800 millimetre ) and one seater sofa ( 3 feet 6 inches ) of full cusion sofa set having teak wood frame and cusion of sleepwell make, finished with high density foam / composit leather or velvet cloth of approved quality and shade as directed by Executive Engineer in charge. Rates are inclusive of all taxes transportation leads and lifts and labour charges including maintenence for two years and material got approved by Executive Engineer before use.

A) First Floor

B) Second Floor

ITEM No. 145 :- Tea Table 900 millimetre X 750 millimetre X 450 millimetre for mild steel ante chamber : Providing And Fixing of Tea Table 900 millimetre X 750 millimetre X 450 millimetre With 12 millimetre Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18 millimetre Thick Waterproofing Ply. The outer laces to be finished with high quality 4 millimetre thick Veneer or 1 millimetre Thick Mica etcetera. (Material including all lead and lifts)

A) First Floor

B) Second Floor

ITEM No. 146 :- Providing and fixing in position Indian VIP sitout in antichmabers, making it with 12 and 6 millimetre, plywood paasting with 1 millimetre thick decorative formica including all necessary fitures and fittings as directed by Engineer Incharge.

A) First Floor

B) Second Floor

ITEM No. 147 :- Providing and fixing in position 12 millimetre Toughened Glass for Table top etcetera complete as directed by Engineer Incharge.

A) First Floor

TOTAL : PART – A (Work Portion)

(ii) Electrical Work

ITEM No. 148 :- (1.2.8) Supplying and erecting PVC trunking (PVC casing-n-capping) of size 32 millimetre with accessories on wall / ceiling as per specification.

ITEM No. 149 :- (1.2.9) Supplying and erecting PVC trunking (PVC casing-n-capping) of size 40 millimetre with accessories on wall / ceiling as per specification.

ITEM No. 150 :- (1.3.1) Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole / Bus bars or any other places as per specification

ITEM No. 151 :- (1.3.1) Supplying and erecting mains with 1x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole / Bus bars or any other places as per specification.

ITEM No. 152 :- (1.3.2) Supplying and erecting mains with 2 X 2.5 sq.mm. FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole / Bus bars or any other places. as per specification

ITEM No. 153 :- (1.3.2) Supplying and erecting mains with 1x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole / Bus bars or any other places. as per specification

ITEM No. 154 :- (1.3.3) Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole / Bus bars or any other places. as per specification

ITEM No. 155 :- (1.3.3) Supplying and erecting mains with 1x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole / Bus bars or any other places. as per specification

ITEM No. 156 :- Mains 1 X 6 sq.mm (1.3.4) Supplying and erecting mains with 1 X 6 sq.mm FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole / Bus bars or any other places. as per specification

ITEM No. 157 :- (1.3.4) Supplying and erecting mains with 2 X 6 sq.mm FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole / Bus bars or any other places. as per specification.

ITEM No. 158 :- (1.6.1) Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

ITEM No. 159 :- (1.6.2) Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete.

ITEM No. 160 :- (1.6.10) Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

ITEM No. 161 :- (1.6.11) Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

ITEM No. 162 :- Telephone Socket (1.6.15) Supplying and erecting modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

ITEM No. 163 :- (1.6.23) Supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

ITEM No. 164 :- (1.6.25) Supplying and erecting modular type blanking plate two module, duly erected on provided plate and box.

ITEM No. 165 :- Modular 1 way Box (1.6.26) Supplying and erecting PVC Surface modular switch box with double mounting plate for 1 module complete duly erected.

ITEM No. 166 :- (1.6.27) Supplying and erecting PVC Surface modular switch box with double mounting plate for 2 module duly erected.

ITEM No. 167 :- (1.6.30) Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module duly erected.

ITEM No. 168 :- (1.6.32) Supplying and erecting PVC Surface modular switch box with double mounting plate for 12 module duly erected.

ITEM No. 169 :- (1.6.38) Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

ITEM No. 170 :- (1.6.40) Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

ITEM No. 171 :- (1.6.43) Supplying and erecting 16 / 20 / 25 A starter (modular range) 2 module for AC unit on provided box complete and duly concealed with necessary material and connected.

ITEM No. 172 :- (1.7.15) Point wiring for light / bell hybrid type (Surface type under false ceiling and concealed type for drops and switch boards on walls) in min 20 millimetre PVC conduit / casing and capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification

ITEM No. 173 :- (1.7.16) Point wiring for ceiling fan (Surface type under false ceiling and concealed type for drops and switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification.

ITEM No. 174 :- (1.7.19) Point wiring for light / bell / exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification.

ITEM No. 175 :- (1.7.20) Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification

ITEM No. 176 :- (1.7.26) Wiring for plug on board with Switch socket surface / concealed type, copper wiring and earthing and with modular accessories as per specification

ITEM No. 177 :- 2 Pair Telephone Cable (1.8.1) Supplying and erecting 2 pair telephone copper cable 0.5 millimetre diametre with high density polyethylene insulation, polyester taped, Nylon Rip Cord and grey colour sheathed with FR PVC, conforming to ITD specification S / WS 113C laid in provided PVC casing capping / conduit as per specification

ITEM No. 178 :- Cat-6 Cable (1.10.1) Supplying and installing cat-6 cable suitable for networking as per specification

ITEM No. 179 :- Patch cord (1.10.16) Supplying and fixing 1 metre UTP patch cord of Cat 6 type in position as per specification

ITEM No. 180 :- RJ-45 (1.12.1) Supplying, installing and testing UTP connector (RJ-45) as per specification

ITEM No. 181 :- Tool-Less (1.12.2) Supplying and fixing tool-less IO (Ethernet) flush / surface type in provided modular box as per specification

ITEM No. 182 :- 24 Ports Switch (1.11.4) Supplying, fixing, and configuring 24 ports with 4 (SFP+) port, ethernet managed switch with web view / CLI, 6KV surge protection on ethernet port and console port for management in provided rack as per specification

ITEM No. 183 :- 6 U Wall Mount Rack (1.12.17) Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 500 X 600 X 367 millimetre) as per specification.

ITEM No. 184 :- (2.1.8) Supplying and erecting LED Panel Light (600 millimetre X 600 millimetre) Maximum 35 W having CRCA powder coated housing, polystyrene diffuser having system lumens output of minimum 4200 Lumens, minimum efficacy of 120 lumen / W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., maximum ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

ITEM No. 185 :- (2.1.15) Supplying and erecting bulk head LED fitting maximum 10W with high transitivity diffuser with system lumens output of minimum 1100 lumens, minimum efficacy of 110 lumen / W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty.

ITEM No. 186 :- (2.1.22) Supplying and erecting inverter LED batten 20W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, minimum 2600 mAh Lithium ion Battery with charging time of 8-10 Hours and backup time of minimum 3 hours with minimum 25% of initial Watts having luminous efficacy of 100 lumen / watt, CRI>80, CCT of 6500K and THD<=20% having useful life of minimum 25000 hours with overheating protection with 2 years warranty.

ITEM No. 187 :- (2.3.13) Supplying and erecting ding dong / electronic musical type call bell with heavy duty coil suitable to operate on 230V A.C. supply erected on polished double wooden block / sunmica block of suitable size.

ITEM No. 188 :- LED Lamp 10-12 Watt. (2.8.11) Supplying and erecting 10-12W, 230V integral type LED Lamp suitable for B-22 / E-27 base.

ITEM No. 189 :- (2.10.4) Supplying and erecting bracket fan 400 millimetre sweep A. C. 230 volts 50 cycles 1350 RPM. Oscillating type, plastic or metal blades chrome plated guard with speed regulator and moisture proof treatment to winding and with ‘E’ class insulation.

ITEM No. 190 :- (2.10.14) Supplying and erecting fresh air cum exhaust fan of light duty 250 V A. C. 50 cycles 225 millimetre 1400 RPM rust proof body and blades, wire mesh, duly erected, complete.

ITEM No. 191 :- Energy Saving Ceiling fan (2.10.22) Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 millimetre, maximum energy consumption of 28W having service ratio (CMM / W) of Minimum 8, PF>0.9, THD<10% with IR remote control / compatible speed regulator, Temperature Rise of Maximum 40 deg. C, having external mounted control PCB completely erected in position as per specification.

ITEM No. 192 :- (2.11.4) Supplying and erecting fan hook of 10 millimetre Mild steel round bar grouted in RCC slab with making the site as original.

ITEM No. 193 :- (3.3.9) Supplying, erecting, testing and commissioning self contained water cooler 230 / 250V 50Hz nominal cooling capacity of 80 litres per hour and storage capacity 120 litres with partially stainless steel body as per specification.

ITEM No. 194 :- (3.5.1) Supplying and erecting ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre / minimum with activated carbon filter and softener operating on 230V, single phase A.C. supply with UV fail and filter change indication system (for TDS more than 200)

ITEM No. 195 :- (5.1.7) Supplying and erecting four pole ON LOAD change over switch, 415V, 315-320A, open execution having staggered termination, phase barrier, shroud termination and terminal cover along with auxiliary contacts and ready to upgrade with fuse protection kit, operational current category AC23A complying to IS/IEC 60947-3 Part-1/3.

ITEM No. 197 :- (5.3.2) Supplying, erecting and marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification

ITEM No. 198 :- MCB DP (5.3.6) Supplying, erecting and marking DPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification.

ITEM No. 199 :- SPMCB 6 A to 32 A (5.3.3) Supplying, erecting and marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification.

ITEM No. 200 :- SPNDB (5.4.9) Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2 millimetre thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification.

ITEM No. 201 :- D.P. MCB (5.4.13) Supplying and erecting CRCA sheet metal one way enclosures of 1.2 millimetre thickness suitable for DP MCB / TP MCB / FP MCB / RCCB / RCBO complete erected on angle iron / GI frame.

ITEM No. 202 :- TPNDB 4 Way (5.4.15) Supplying and erecting triple pole and neutral distribution board (TPNDB), 3 pole / 4 pole MCCB as incomer and outgoing SP MCB (12 poles) or TP MCB of 4 ways (12 poles), with door, 1.2 millimetre thickness, surface / flush mounted, on iron / GI frame (vertical busbar type) as per specification

ITEM No. 203 :- (5.5.1) Providing and erecting 4 Pole MCCB, 415 V, 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt / UV / trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure / panel as per specification

ITEM No. 204 :- (5.5.3) Providing and erecting 4 Pole MCCB 415V, 250A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt / UV / trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure / panel as per specification.

ITEM No. 205 :- MCCb 04 Pole (5.5.4) Providing and erecting 4 Pole MCCB 415V, 400A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt / UV / trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure / panel as per specification.

ITEM No. 206 :- (5.6.2) Supplying, erecting and commissioning 2 pole RCCB 40A, electromagnetic type with 30 / 100 / 300 mA sensitivity with earth leakage trip indication complete as per specification.

ITEM No. 207 :- (5.7.3) Providing and erecting floor / wall mounting, MCCB panel board, with door, suitable for four pole incoming 250A, 6 ways four pole outgoing, up to 100 A MCCBs on iron frame, as per specification (Excluding MCCBs)

ITEM No. 208 :- (5.7.13) Providing and erecting incoming and outgoing cable alleys suitable for MCCB panel board with door, 250A incoming and 6 way outgoing or 400A incoming and 4 way outgoing made from CRCA sheet 1.6 millimetre thick duly powder coated and having vertical insulated partition for shielding between the shared face of cableway and DB.

ITEM No. 209 :- (5.7.17) Providing and erecting prewired meter module suitable for MCCB panel board with CTs and emfs VIF meter.

ITEM No. 210 :- (5.10.28) Supplying and erecting porcelain / epoxy bus bar support complete erected in provided M.S. box for 400A

ITEM No. 211 :- (5.11.19) Supplying and erecting SS enclosure for MCCB suitable for above 250 A up to 800A MCCB.

ITEM No. 212 :- (6.2.4) Supplying and erecting bus bar chamber triple pole with neutral with four aluminium bars, 500V 400A having 50 millimetre (Width) X 5 millimetre (Thickness), with 99.9 % aluminium purity as per E91E Grade and Current Density 0.8 A per sq. mm. compliance to IS 5082 and enclosure fabricated with 16 SWG CRCA sheet and epoxy paint, with suitable number of ways and with SMC / DMC Insulators and accessories of suitable rating complete as per specification.

ITEM No. 213 :- Cable 3½ core 25 sq. mm. (7.1.15) Supplying, erecting and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 25 sq. mm. aluminium conductor complete erected with glands and lugs, on wall / trusses / pole or laid in provided trench / pipe as per specification.

ITEM No. 214 :- Arm. cable 3½ core 95 sq. mm. (7.1.19) Supplying, erecting and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands and lugs, on wall / trusses / pole or laid in provided trench / pipe as per specification.

ITEM No. 215 :- Cable 3½ core 120 sq. mm. (7.1.20) Supplying, erecting and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm. aluminium conductor complete erected with glands and lugs, on wall / trusses / pole or laid in provided trench / pipe as per specification.

ITEM No. 216 :- (7.11.1) Providing and erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 millimetre thick) GI sheet of 150 millimetre width and 100 millimetre height comprising all required standard accessories.

ITEM No. 217 :- D.W.C. Pipe 120 millimetre (7.6.12) Supplying and laying (including excavation of suitable width and depth up to 90 cm) 120 millimetre outside diametre double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground / road surface, to required depth complete.

ITEM No. 218 :- (9.1.1) Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 centimetres complete with all materials, testing and recording the results as per specification.

ITEM No. 219 :- (9.2.3) Supplying and erecting GI strip of high purity required size used for earthing on wall and / or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required as per specification

ITEM No. 220 :- (9.1.4) Providing pipe type earthing with 40 millimetre diametre Galvanised iron pipe or 20 millimetre diametre Galvanised iron Rod complete with all materials testing and recording the results as per specification

ITEM No. 221 :- Split Type A.C. (3.2.11) Supplying, installing, testing and commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3TR to 1.6TR capacity having ISEER minimum 5.00 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall / floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation and temperature display on indoor unit, noise level maximum 50dBA at position as per specification.

ITEM No. 222 :- Copper Pipe (3.2.26) Supplying and erecting seamless outside and inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner diametre / size 12 millimetre complete.

ITEM No. 223 :- Copper Pipe (3.2.27) Supplying and erecting seamless outside and inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner diametre / size 16 millimetre complete.

ITEM No. 224 :- Elastomeric (4.2.9) Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 millimetre thickness and inner diameter / sizes 12 millimetre for solar water heater / AC system.

ITEM No. 225 :- Elastomeric (4.2.10) Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 millimetre thickness and inner diameter / sizes 16 millimetre for solar water heater / AC system.

ITEM No. 226 :- Iron Work (6.1.19) Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etcetera for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

ITEM No. 227 :- Flexible Conduit 25 millimetre (1.2.2) Supplying and erecting 25 millimetre diametre corrugated flexible polypropylene conduit

ITEM No. 228 :- Mains 2x6 sq.mm (1.3.4) Supplying and erecting mains with 2 X 6 sq.mm FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole / Bus bars or any other places. as per specification.

ITEM No. 229 :- TPMCB 6 A to 32 A (5.3.10) Supplying, erecting and marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification.

ITEM No. 230 :- FPMCB 40 A to 63 A (5.3.13) Supplying, erecting and marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification.

ITEM No. 231 :- Change Over Switch (5.3.26) Supplying, fixing and commissioning MCB type change over switch 4 pole, 63A with 3 positions (I-O-II) with centre off position as per specification

ITEM No. 232 :- TPNDB (5.4.4) Supplying and erecting triple pole and neutral distribution board (TPNDB), SP / TP MCBs total 4 ways / 12 Poles, with door, 1.2 millimetre thickness surface / flush mounted, IP 43 Protection on iron / GI frame (vertical busbar type) as per specification.

ITEM No. 233 :- MCB Enclosures (5.4.13) Supplying and erecting CRCA sheet metal one way enclosures of 1.2 millimetre thickness suitable for DP MCB / TP MCB / FP MCB / RCCB / RCBO complete erected on angle iron / GI frame.

ITEM No. 234 :- CRCA Sheet (6.1.1) Supplying and erecting metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etcetera including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete.

ITEM No. 235 :- Iron Work (6.1.19) Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etcetera for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

ITEM No. 236 :- FRXLPE 4x16 Cable (7.1.29) Supplying, erecting and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. aluminium conductor complete erected with glands and lugs, on wall / trusses / pole or laid in provided trench / pipe as per specification.

ITEM No. 237 :- FR XLPE Cable (7.2.32) Supplying, erecting and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands and lugs, on wall / trusses / pole or laid in provided trench / pipe as per specification.

ITEM No. 238 :- G. I. Pipe 40 millimetre (7.6.2) Supplying and erecting G.I. pipe ‘A’ class 40 millimetre diametre erected for enclosing XLPE armoured cable on wall / pole as per specification.

ITEM No. 239 :- D.W.C. Pipe 50 millimetre (7.6.9) Supplying and laying (including excavation of suitable width and depth up to 90 centimetre) 50 millimetre outside diametre double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground / road surface, to required depth complete.

ITEM No. 240 :- Pipe Type Earthing (9.1.4) Providing pipe type earthing with 40 millimetre diametre Galvanised Iron pipe or 20 millimetre diametre Galvanised Iron Rod complete with all materials testing and recording the results as per specification.

ITEM No. 241 :- Submersible Pump Set (12.2.10) Supplying and erecting minimum Three and above star rated submersible pump set of 5.625 KW / 7.5 HP with 415 V, 50 c / s AC supply suitable for 150 millimetre diametre borewell suitable for 110 to 510 LPM discharge at 107 to 30 metre head and discharge and delivery pipe of Size-50 mm diameter with a necessary H type clamps as per specification.

ITEM No. 242 :- Open Well Submersible Pump Set (12.3.2) Supplying and erecting minimum Three and above star rated submersible pump set suitable for erection on open well of 3.75 KW / 5 HP with 415 V 50 c / s. A.C. supply, having delivery head from 43 to 11 metre and discharge from 120 to 840 litres per minute and pipe of Suction 65 millimetre / Delivery 50 millimetre diameter erected with necessary H type clamps as per specification.

ITEM No. 243 :- Flat Flexible 3x4 sq.mm. Cable (12.4.9) Supplying and erecting flat flexible 3 core 4 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

ITEM No. 244 :- Automatic Control Panel (12.4.17) Supplying and erecting automatic control panel for 3 Phase , 415 volt, A.C, Submersible / centrifugal pump set up to 7.5 HP consisting of DOL starter having relay range 9-14 AMP,S.P.P., Combined ammeter / voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etcetera

ITEM No. 245 :- Cement concrete Foundation (16.3.7) Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) millimtre stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

ITEM No. 246 :- Galvanised Iron Pipe 50 millimetre (16.5.6) Supplying and erecting ISI mark GI pipe 50 millimetre diametre ‘B’ class at position with accessories complete as per specification.

ITEM No. 247 :- Non Return Valve 50 millimetre Diametre (16.6.21) Supplying and erecting non return valve 50 millimetre diametre in position made of gun metal complete.

ITEM No. 248 :- Cable 03 Core Flexible 0.25 sq.mm. (1.3.15) Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 numbers x 0.25 millimetre diametre) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV.

ITEM No. 249 :- LED Street Light fitting 60 W. (2.4.5) Supplying and erecting integrated LED street light fitting 60W IP65 and IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Minimum 6600 Lumens, minimum efficacy of 110 lumen / W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver complete with 3 Years warranty as per specification.

ITEM No. 250 :- LED Flood Light 120 Watt. (2.4.16) Supplying and erecting integrated LED flood light fitting maximum 120W IP65 and IK07 class having pressure die-cast aluminium housing, having system lumens output of Minimum 14500 Lumens, minimum efficacy of 120 lumen / W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver with U shaped bracket with 3 Years warranty as per specification.

ITEM No. 251 :- LED Post Top (2.4.21) Supplying and erecting integrated LED Post Top 45W IP65 and IK10 class having die cast aluminium housing with UV protected polycarbonate diffuser, having system lumens output of minimum 4500 Lumens, minimum efficacy of 100 lumen / W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 30,000 Hrs. at L50B50 , including driver complete with 2 Year warranty as per specification.

ITEM No. 252 :- Street Light Bracket (2.7.4) Supplying and erecting street light Wall bracket made from 40 millimetre diametre ‘G.I. pipe 1.2 metre in total length complete as per specification.

ITEM No. 254 :- SPMCB 0.5A to 5A, (5.3.1) Supplying, erecting and marking SPMCB 0.5A to 5A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification.

ITEM No. 255 :- D.P. Isolator (5.3.14) Supplying, erecting and marking double pole isolator only switch version of miniature circuit breaker of 40A with required wiring connections and lugs etcetera in provided distribution board.

ITEM No. 256 :- D.P. MCB (5.4.13) Supplying and erecting CRCA sheet metal one way enclosures of 1.2 millimetre thickness suitable for DP MCB / TP MCB / FP MCB / RCCB / RCBO complete erected on angle iron / GI frame.

ITEM No. 257 :- CRCA Sheet (6.1.1) Supplying and erecting metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etcetera including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete.

ITEM No. 258 :- Iron Work (6.1.19) Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etcetera for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

ITEM No. 259 :- FR XLPE 4x6 sq.mm. (7.1.27) Supplying, erecting and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. aluminium conductor complete erected with glands and lugs, on wall / trusses / pole or laid in provided trench / pipe as per specification.

ITEM No. 260 :- D.W.C. Pipe 50 millimetre (7.6.9) Supplying and laying (including excavation of suitable width and depth up to 90 centimetre) 50 millimetre outside diametre double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground / road surface, to required depth complete.

ITEM No. 261 :- FRP Box (7.8.8) Supplying and erecting FRP box of size 150 millimetre x 125 millimetre x 100 millimetre, 2.7 millimetre thick complete on pole / wall as per specification.

ITEM No. 262 :- Octagonal Pole 6 Metre (8.2.12) Providing and erecting 6 metre high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 millimetre A / F, top 70 millimetre A / F on provided foundation as per specification.

ITEM No. 263 :- Sword Type Bracket (8.2.21) Providing and erecting galvanised 1000 millimetre single arm sword type bracket with FRP dome and ball as per specification.

ITEM No. 264 :- Sword Type Double Bracket (8.2.22) Providing and erecting galvanised 1000 millimetre double arm sword type bracket with FRP dome and ball as per specification.

ITEM No. 265 :- Plate Earthing (9.1.1) Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 centimetre complete with all materials, testing and recording the results as per specification

ITEM No. 266 :- Pipe Type Earthing (9.1.4) Providing pipe type earthing with 40 millimetre diametre Galvanised Iron pipe or 20 millimetre diametre G.I. Rod complete with all materials testing and recording the results as per specification

ITEM No. 267 :- C.C. Foundation for Pole (16.3.9) Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T / sq.m at 1.5 metre depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6 metre to 8 metre high octagonal / conical GI pole).

ITEM No. 268 :- Galvanised Iron Pipe 40 millimetre (16.5.5) Supplying and erecting ISI mark GI pipe 40 millimetre diametre ‘B’ class at position with accessories complete as per specification

ITEM No. 269 :- Conduit 25 millimetre (1.2.4) Supplying and erecting HMS PVC conduit FRLS grade 25 millimetre diametre with PVC accessories on wall / ceiling as per specification

ITEM No. 270 :- Water Tank (4.8.7) Providing and fixing high-density polyethylene (HDPE) container one piece moulded triple layer water tank made out of high density polyethylene and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity up to 20000 litres.

ITEM No. 271 :- FR XLPE 4x6 sq.mm. (7.1.27) Supplying, erecting and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. aluminium conductor complete erected with glands and lugs, on wall / trusses / pole or laid in provided trench / pipe as per specification

ITEM No. 272 :- Automatic Control Panel (12.4.17) Supplying and erecting automatic control panel for 3 Phase, 415 volt, A.C, Submersible / centrifugal pump set up to 7.5 HP consisting of DOL starter having relay range 9-14 AMP, S.P.P., Combined ammeter / voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etcetera.

ITEM No. 273 :- Booster fire Pump (13.3.1) Supplying, installation, testing and commissioning of booster fire pump [BP] suitable for water discharge of 450 LPM at 35 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 5.5 kW or of suitable kW capacity for manual / automatic operation and consisting of following : (a) Horizontal / vertical type, single / multi stage, centrifugal casing pump of cast iron body and bronze / CI impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etcetera as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification.

ITEM No. 274 :- G.I. Pipe ERW 25 millimetre (13.6.2) Supplying and erecting Galvanised Iron pipe ‘C’ class ERW 25 millimetre diametre with necessary fittings complete as per specification.

ITEM No. 275 :- G.I. Pipe ERW 100 millimetre (13.6.6) Supplying and erecting Galvanised Iron pipe ‘C’ class ERW 100 millimetre diametre with necessary fittings complete as per specification.

ITEM No. 276 :- Line Strainer (13.7.10) Supplying and erecting 100 millimetre diametre Cast Iron end line strainer of T-Pot type flanged end pattern, PN16 pressure rating, screen of SS and end connection with flanged, for positive suction complete as per specification.

ITEM No. 277 :- Sluice Valve (13.7.14) Supplying and erecting 100 millimetre diametre cast iron double flange sluice valve complete with PN16 pressure rating, as per specification.

ITEM No. 278 :- Ball Type NRV (13.7.28) Supplying and erecting 100 mm dia cast iron double flange ball type NRV complete with PN16 pressure rating, as per specification

ITEM No. 279 :- Gate Valve (13.7.32) Supplying and erecting 25 millimetre diametre gun metal gate valve complete with PN16 pressure rating, as per specification

ITEM No. 280 :- Hydrant Valve (13.7.35) Supplying and erecting stainless steel single outlet hydrant valve fitted with necessary accessories complete as per specification

ITEM No. 281 :- Hose reel (13.8.2) Supplying and installing wall mounting swinging hose reel drum fitted with 19 millimetre diametre 30 metre long high pressure polypropylene (Polyhose) along with necessary accessories complete as per specification

ITEM No. 282 :- R.R.L. (13.8.4) Supplying and erecting 63 millimetre diametre, reinforced rubber lined (R.R.L.) hose pipe, 15 metre in length, fitted with necessary accessories complete as per specification.

ITEM No. 283 :- Nozzle (13.8.8) Supplying and erecting stainless steel branch pipe 63 millimetre diametre fitted with 20 millimetre diametre detachable hexagonal nozzle complete as per specifications.

ITEM No. 284 :- Fire Brigade Header 150 millimetre (13.8.10) Supplying and erecting 150 millimetre diametre fire brigade header suitable for supplying water in fire tank complete as per specification.

ITEM No. 285 :- Siamese Connection (13.8.11) Supplying and erecting fire brigade header (Siamese connection )of 150 millimetre diametre, for supplying water in fire tank complete as per specification.

ITEM No. 286 :- Air Release Cock (13.8.13) Supplying and erecting 20 / 25 millimetre diametre gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification.

ITEM No. 287 :- Pressure Gauge (13.8.14) Supplying and erecting 100 millimetre diametre pressure gauge, 0-300 PSI or 0-14 kilogram per cm square fitted with 12 / 15 millimetre diametre pad cock valve, erected with provided Galvanised Iron pipe, elbow etcetera complete as per specification

ITEM No. 288 :- Pressure Switch (13.8.15) Supplying and erecting 12 / 15 millimetre diametre pressure switch with provided isolation valve, G.I. nipple, elbow, etcetera complete as per specification.

ITEM No. 289 :- Cabinet (13.8.18) Supplying and erecting Mild steel / CRCA cabinet for housing single hydrant valve of size (400 x 400 x 400) millimetre or hose pipe box of size ( 600 x 600 x 200) millimetre made from minimum 1.5 millimetre thick CRCA sheet with angle iron work of minimum of size (25 x 25 x 4) millimetre having front doors with viewing glass of size (200 X 150) millimetre and locking arrangement with necessary fixing material such as rubber bidding etcetera duly painted in post box red colour (Code 538 of IS 5).

ITEM No. 290 :- (13.8.19) Supplying and erecting Mild Steel / CRCA cabinet for housing Fire Brigade / SIEMESE connections (size 1250 x 400 x 300 millimetre ) made from 16 SWG sheet and angle iron 25 millimetre x 25 millimetre x 4 millimetre having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etcetera duly painted in post box red colour (Code 538 of IS 5)

ITEM No. 291 :- Smoke Detector (13.9.3) Supplying, erecting testing and commissioning optical type smoke detector on suitable back box with necessary connections complete as per specification.

ITEM No. 292 :- Pill Box (13.9.6) Supplying, erecting testing and commissioning manual call point (Pill box) with break glass, push button (resettable type) in metal enclosure complete as per specification.

ITEM No. 293 :- Hooters (13.9.8) Supplying, erecting, testing and commissioning hooters having high (100dB @ 1 metre) and low (94dB @ 1 metre) volume setting, group addressing facility allowing multiple sounders to be activated with CRCA enclosure complete as per specification

ITEM No. 294 :- Arm Cable 2x1.5 sq.mm (13.9.10) Supplying, installing, testing and commissioning FRLX, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall / ceiling complete as per specification.

ITEM No. 295 :- 04 Zones panel (13.9.14) Supplying, installing, testing and commissioning of 4 Zones Microprocessor based conventional fire alarm control panel (FACP) with standard accessories, 16 X 2 Character LCD Display, provision for zone wise contact and beep sound alarm, suitable to operate on 120-220 V AC, 0 - 49 Deg C, 93 ± 2 Percentage RH (non- condensing) at 32 ± 2 Deg C complete as per specification.

ITEM No. 296 :- CO2 (13.15.1) Supplying and erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kilogram capacity cartridge type conform to IS 2878 / 15683 complete erected with necessary clamp made from 50 x 6 millimetre M. S. flat with nut and bolts routed in wall complete.

ITEM No. 297 :- Cement concrete Foundation (16.3.7) Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) millimetre stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

ITEM No. 298 :- Supplying and Installing auto Glow (Viewing upto 15 Metre Length) fire signages Viz fire Hydrant, fire Extinguishers, fire Exist, fire Door, fire Hose Box, fire and Electrical safety etcetera size 300 millimetre x 100 millimetre)

ITEM No. 299 :- Supplying and Installing auto Glow (Viewing upto 15 Metre Length) fire signages Viz fire Hydrant, fire Extinguishers, fire Exist, fire Door, fire Hose Box, fire and Electrical safety

ITEM No. 300 :- Supplying and erecting ABC powder type fire extinguisher as per IS : 13849 / 15683 of 6 kg capacity with necessary clamp for erection on wall.

ITEM No. 301 :- Supplying, Erecting, Testing and Commissioning 32 Channel NVR Complete. Video / Audio IP Video Input 32-ch Two-way Audio Input 1-ch, RCA Network Incoming bandwidth 160Mbps Outgoing bandwidth 64Mbps Remote Users 128Protocols P2P, UPnP, NTP, DHCP, PPPOEVideo / Audio Output HDMI / VGA Output HDMI: 4K (3840 X 2160) @ 30, 1920 X 1080p @ 60, 1920 X 1080p @ 50 , 1600 X 1200 @ 60, 1280 X 1024 @ 60, 1280 X 720 @ 60, 1024 X 768 @ 60 VGA: 1920 X 1080p @ 60, 1920 X 1080p @ 50, 1280 X 1024 @ 60, 1280 X 720 @ 60, 1024 X 768 @ 60Audio Output 1-ch, RCA Recording Resolution 8MP / 5MP / 4MP / 3MP / 1080p / 960p / 720p / 960H / D1 / 2CIF / CIF Synchronous Playback 32-chCorridor Mode Screen 3 / 4 / 5 / 7 / 9 / 10 / 12 / 16 / 32 Decoding Decoding Format Ultra 265 / H.265 / H.264Live view / Playback 8MP / 5MP / 4MP / 3MP / 1080p / 960p / 960H / 720p / D1 / 2CIF / CIF Capability 2 X 4K @ 30, 3 X 5MP @ 30, 4 X 4MP @ 30, 5 x 3MP @ 30, 8 x 1080p @ 30, 16 x 720p @ 30,32 x D1Hard disk SATA 2 SATA interfaces Capacity up to 6TB for each diskExternal Interface Network Interface 2 RJ-45 10M / 100M / 1000M self-adaptive Ethernet Interfaces USB Interface Rear panel: 1 X USB2.0, 1 x USB3.0 Front panel: 1 x USB2.0 (Include - 12 Month Fully Compressive Warranty)

ITEM No. 302 :- Supplying, Erecting, Testing and Commissioning 5 MP Full IP Dome Camera complete. Supplying, Erecting, Testing and Commissioning 5 MP Full IP Dome Camera Complete. 1 - Video Compression - Main stream: H.265 / H.264 / H.264+ / H.265+ Sub-stream: H.265 / H.264 / MJPEG Third stream: H.265 / H.264 Fourth stream: H.265 / H.264 / MJPEG 2 - Video Resolution - 2592 × 1944 3 - Frame rate - 50 Hz: 25 fps (2592 × 1944, 2688 × 1520, 2560 × 1440, 2304× 1296, 1920 × 1080, 1280 × 1024, 1280 × 960, 1280 × 720) 60 Hz: 24 fps (2592 × 1944) 30 fps (2688 × 1520, 2560 × 1440, 2304× 1296, 1920 × 1080, 1280 × 1024, 1280 × 960, 1280 × 720). 4 - Image Sensor - 1 / 2.7" Progressive Scan CMOS. 5 - Lens Type - fixed focal lens, motor-driven lens, 6 - Lens - 2.7 to 13.5 millimetre. 7 - Minimum Illumination - Color: 0.003 Lux @ (F1.4, AGC ON), B / W: 0 Lux with IR 8 - Image settings - Compression, colour, brightness, sharpness, contrast, white balance, exposure control, backlight compensation Auto / natural / street lamp / outdoor / manual / regional custom 9 - Audio - 1 input (line in), 3.5 mm connector, max. input amplitude: 3.3 vpp, input impedance: 4.7 KΩ, interface type: non-equilibrium; 1 output (line out), 3.5 mm connector, max. output amplitude: 3.3 vpp, output impedance: 100 Ω, interface type: non-equilibrium 10 - Protocol - TCP / IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTCP, RTSP, NTP, UPnP, SMTP, IGMP, 802.1X, QoS, IPv4, IPv6, UDP, Bonjour, SSL / TLS, PPPoE, ARP, SNMP, SIP, Multicast 11 - Security – Password protection, complicated password, HTTPS encryption, IP address filter, IP conflict, Security Audit Log, basic and digest authentication for HTTP / HTTPS, TLS 1.1 / 1.2, WSSE and digest authentication for Open Network Video Interface. 12 - Operating conditions - -30 °C to 60 °C (-22 °F to 140 °F). Humidity 95% or less (non-condensing) 13 - Casing - Metal + Plastic (Include - 24 Month Fully Compressive Warranty)

ITEM No. 303 :- Supplying, Erecting, Testing and Commissioning 5 MP Full IP Bullet Camera Complete, 1 - Video Compression - Main stream: H.265 / H.264 / H.264+ / H.265+ Sub-stream: H.265 / H.264 / MJPEG Third stream: H.265 / H.264 Fourth stream: H.265 / H.264 / MJPEG 2 - Video Resolution - 2592 × 1944 3 - Frame rate - 50 Hz: 25 fps (2592 × 1944, 2688 × 1520, 2560 × 1440, 2304× 1296, 1920 × 1080, 1280 × 1024, 1280 × 960, 1280 × 720) 60 Hz: 24 fps (2592 × 1944) 30 fps (2688 × 1520, 2560 × 1440, 2304× 1296, 1920 × 1080, 1280 × 1024, 1280 × 960, 1280 × 720) 4 - Image Sensor – 1 / 2.7" Progressive Scan CMOS 5 - Lens Type - fixed focal lens, motor-driven lens, 6 - Lens - 2.7 to 13.5 millimetre 7 - Minimum Illumination - Color: 0.003 Lux @ (F1.4, AGC ON), B / W: 0 Lux with IR 8 - Image settings - Compression, colour, brightness, sharpness, contrast, white balance, exposure control, backlight compensation Auto / natural / street lamp / outdoor / manual / regional custom 9 - Audio - 1 input (line in), 3.5 mm connector, max. input amplitude: 3.3 vpp, input impedance: 4.7 KΩ, interface type: non-equilibrium; 1 output (line out), 3.5 millimetre connector, maximum output amplitude: 3.3 vpp, output impedance: 100 Ω, interface type: non-equilibrium (optional) 10 - Protocol - TCP / IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTCP, RTSP, NTP, UPnP, SMTP, IGMP, 802.1X, QoS, IPv4, IPv6, UDP, Bonjour, SSL / TLS, PPPoE, ARP, SNMP, SIP, Multicast 11 - Security - Password protection, complicated password, HTTPS encryption, IP address filter, IP conflict, Security Audit Log, basic and digest authentication for HTTP / HTTPS, TLS 1.1 / 1.2, WSSE and digest authentication for Open Network Video Interface 12 - Operating conditions - -30 °C to 60 °C (-22 °F to 140 °F). Humidity 95% or less (non-condensing) 13 - Casing - Metal + Plastic (Include - 24 Month Fully Compressive Warranty)

ITEM No. 304 :- 40" LED Ultra HD Display (NSCR) Supplying and erecting supplying installation configuring and commissioning 40" LED TELEVISION (TV) Screen Size: 100.33 cms (39.5) Display type: LEd power AC 100V-24V-50 / 60 HZ st By Consumption : <0.5W,Power Consumption: 75 W, Maximum Audio Output power (RMS) 10W X 2 Speaker Specification: 8 / 10W Antenna (RF): 75 TV system PAL (B / G,D / K,I) video input format PAL / SECAM / NTSC, YPBPR input formats 720p, 1080i, 1080p HDMI input formats: Up to 1920 x 1080, Computer INPUT Frequency: 60 hZ, wifi, ethernet CONNECTIVITY RJ45, make index.

ITEM No. 305 :- (1-8-1) H.D.D. (NSCR) Supplying and erecting supplying installation configuring and commissioning of high speed hard disk 8 TB 3.5 buffer:64 mb intelipower make:WD

ITEM No. 306 :- Camera stand (NSCR) Supplying, installing and Commissioning of CCTV Barcket for Dome and Bullet Camera complete, Mounting Type Tripod, Wall Mount, Ceiling Mount Dimensions L x W x H 8 x 5 x 8 centimeters.

ITEM No. 307 :- PVC Trunking 25 millimetre (1.2.7) Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 millimetre with accessories on wall / ceiling as per specification

ITEM No. 308 :- 3 Core Flexible Cable (1.3.14) Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 number X 0.25 millimetre diametre ) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

ITEM No. 309 :- Modular Switch 6 A (1.6.1) Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

ITEM No. 310 :- Modular Switch 16 A (1.6.2) Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete.

ITEM No. 311 :- Modular Socket 6A (1.6.10) Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

ITEM No. 312 :- Modular Socket 16A (1.6.11) Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

ITEM No. 313 :- Modular 6 way Box (1.6.30) Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module duly erected.

ITEM No. 314 :- 20 M HDMI Cable (1.8.25) Supplying and erecting 20 metre HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male / female 19 pin HDMI connectors complete.

ITEM No. 315 :- Cat-6 Cable (1.10.1) Supplying and installing cat-6 cable suitable for networking as per specification.

ITEM No. 316 :- POE Switch 8-Port (1.11.1) Supplying, fixing, and configuring 8-ports 1 G unmanaged gigabit POE switch erected in provided rack complete.

ITEM No. 317 :- 24 Ports Switch (1.11.4) Supplying, fixing, and configuring 24 ports with 4 (SFP+) port, ethernet managed switch with web view / CLI, 6KV surge protection on ethernet port and console port for management in provided rack as per specification.

ITEM No. 318 :- RJ-45 (1.12.1) Supplying, installing and testing UTP connector (RJ-45) as per specification.

ITEM No. 319 :- 6 U Wall Mount Rack (1.12.17) Supplying and fixing 6U wall mount rack (Dimension – D x W x H – 500 X 600 X 367 millimetre) as per specification.

ITEM No. 320 :- Caution Board (6.1.16) Supplying and erecting GI sheet 1.6 millimetre (16 SWG) caution board of size 250 x 200 millimetre duly painted with red oxide and enamel paint in Marathi, Hindi and English erected at position for HV / EHV (11000 Volts) installation with compliance to IS 2551-1982

ITEM No. 321 :- Iron Work (6.1.19) Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etcetera for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

ITEM No. 322 :- D.T.C. meter (6.3.5) Supplying and erecting LT CT multifunction DLMS compliance energy meter of accuracy of class 0.5, 3 X 240V, 50 Hz with optical and RS 232 port, backlit LCD, measure and display trivector energy, load survey, TOD, tamper detection and logging, power ON / OFF events, instantaneous parameters of rating 1 / 5 A with display in absence of power complete with zero adjustment and test certificate from manufacturer erected on provided M. S. box and connected to CTs.

ITEM No. 323 :- L.T. (6.5.2) Supplying and erecting LT current transformer with bar primary 50 / 5 to 1000 / 5 ratio with 15 VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates.

ITEM No. 324 :- Un Arm Copper cable 1x120 sq.mm (7.2.6) Supplying, erecting and terminating XLPE insulated unarmoured cable 1100 V. 1 core 120 sq. mm. copper conductor complete erected with provided lugs, laid in provided control panel / distribution boards / pipe as per specification.

ITEM No. 325 :- Girder Pole (8.1.13) Supplying and erecting rolled steel joist (girder) pole 100 x 116 millimetre (23 kg / metre) with base plate in provided foundation as per specification.

ITEM No. 326 :- V Cross Arm (8.3.12) Supplying and erecting V cross arm with ISM channel of 75 X 40 X 6 millimetre for 11kV HT OH line with arrangement to fix insulator at 45 millimetre from the end and horizontal distance between insulators 1220 millimetre bent at angle of 60 degree keeping base 305 millimetre and the total vertical height of V cross arm as 460 millimetre, and fixed on pole with MS clamp of 80 X 10 millimetre, nut bolts, washers complete as per specification.

ITEM No. 327 :- Top Clamp (8.3.14) Supplying and erecting 75 X 40 X 6 millimetre with 4.40 millimetre thick web and 7.30 millimetre thick flange channel (top pin) with clamp of suitable length so as to maintain vertical clearance of 1065 millimetre for 11kV, 1320 millimetre for 22kV between insulators for erection of top pin insulators complete as per specification.

ITEM No. 328 :- Guarding Bracket (8.3.15) Supplying and erecting bracket for guarding of HT OH Line, made from channel iron 1600 millimetre in length and 75 X 40 X 6 millimetre erected on pole complete as per specification.

ITEM No. 329 :- Single Pole cut Point (8.3.17) Supplying and erecting single pole cut point channel set of for 11kV HT OH line two channel of size 100 X 50 X 6 millimetre 1.6 metre long having stud angle of size 50 X 50 X 6 metre 1.5 metre long with necessary clamps, nut bolts etcetera complete as per drawing.

ITEM No. 330 :- Transformer (8.3.26) Supplying and erecting end pole D. P. Structure for 11 / 0.415 kV, 200 kVA Transformer with R.S.J. Pole 2 Numbers of size 100 millimetre x 116 millimetre x 11 metre Long with suitable Distribution Box of C.R.C.A. Sheet 16 SWG with 4 Pole MCCB 400 Amps as incomer and 6 Numbers200 Amps Kitkat / MCCB for out - going circuits. Transformer D.P. Structure includes the A. B. Switch 200 Amps, D.O. fuse Set and L.A. Set. 2 Numbers Top channel of size 100 millimetre X 50 millimetre for erection of A.B. Switch and 2 Numbers Base channel of size 100 millimetre x 50 x millimetre for erecting Transformer. Channel of size 75 x 40 millimetre for erecting D.O. Fuse Set, L.A., A.B. Switch handle etcetera Angle of size 50 x 50 x 6 millimetre for erecting Distribution Box , Transformer Belt etcetera as per drawing (minimum 124 Kilogram iron work) with necessary clamps, Nut-bolts. V cross arm, top clip, insulators etcetera complete with caution board and barbed wire. D.P. Structure shall be erected in cement concrete foundation complete.

ITEM No. 331 :- ACSR Conductor (8.4.7) Supplying and erecting ACSR conductor of size 6 / 1 - 2.59 millimetre complete. (Weasel) (127.7 kilogram per kilometre) as per specification.

ITEM No. 332 :- Disc Insulator (8.5.6) Supplying and erecting porcelain disc type insulator 45KN with necessary hardware suitable for 11kV line, complete as per specification.

ITEM No. 333 :- Pin Insulator (8.5.9) Supplying and erecting porcelain pin type insulator with GI pin suitable for 11kV line, complete as per specification.

ITEM No. 334 :- G.I. Stay (8.6.2) Supplying and erecting G.I. stay set for poles, including loop insulators at inaccessible height with anchor plate 300 X 300 X 6 millimetre, straining screws, G.I. stay wire 7 / 8 SWG, G.I. stay rod 20 millimetre x 1.8 metre length and pole clamps duly erected in provided cement concrete foundation complete.

ITEM No. 335 :- Guarding Lace (8.6.18) Supplying and erecting guarding lace for HT OH line with 8SWG G.I. wire to protect the HT OH line with binding wire of 20 SWG G.l. wire for 75 millimetre section on either side.

ITEM No. 336 :- Galvanized Iron Earth Plate (9.1.3) Providing earthing with galvanized iron earth plate size 60 X 60 X 0.6 centimetre with funnel with a wire mesh for watering and brick masonry block C. I. cover complete with all materials, testing and recording the results as per specification.

ITEM No. 337 :- Pipe Type Earthing (9.1.4) Providing pipe type earthing with 40 millimetre diametre G. I. pipe or 20 millimetre diametre G.I. Rod complete with all materials testing and recording the results as per specification.

ITEM No. 338 :- G. I. Strep (9.2.3) Supplying and erecting GI strip of high purity required size used for earthing on wall and / or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required as per specification (25 X 5 X 15 Metre = @ 0.335 / Kg = 5.025 Kilogram)

ITEM No. 339 :- G. I. Earth Wire (9.2.5) Supplying and erecting GI wire of high purity of required sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall / cable / conduit with screws complete.

ITEM No. 340 :- C. C. Foundation (16.3.4) Making cement concrete foundation including excavation (60 x 60) centimetre X deep 1 / 6 of pole length in 1:3:6 cement concrete 20 X 25 millimetre stone metal, 45 centimetre X 45 centimetre x 45 centimetre / 45 centimetre diametre x 45 centimetre height plinth duly plastered, with necessary curing and finishing complete. (for above 9 metre poles)

ITEM No. 341 :- Cement concrete Foundation (16.3.6) Making cement concrete foundation including excavation (60 x 60 x 150) centimetre deep in 1:3:6 cement concrete, (20 to 25) millimetre stone metal with necessary curing and finishing complete. (for stay).

ITEM No. 342 :- Transformer 200 KVA (Non C.S.R.) Supplying, Installing, Testing and Commissioning 03 Phase, 11 / 0.433 KV, 50 Hz, 200 KVA, Aimeral oil immersed and naturally cooled outdoor type, alluminium wound Non-sealed transformer delta / star connected with additional neutral brought out on load side, Temperature rise should not exceed 45 C by thermometer in oil and 50 C by the resistance method in winding at full load rating, using type A winding insulation (kraft paper) with HV tapping (with off load tap changer) off load +2.5 to -5 in steps of 2.5%, having 4 number of tap positions, with losses below 780 watts at 50% load, 2300 watts at 100 load as per IS: 1180 (part 1) : 2014, with necessary permissions of Electrical inspector, as per specification.

ITEM No. 343 :- MCCB 04 Pole (5.5.2) Providing and erecting 4 Pole MCCB, 415V, 200A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt / UV / trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure / panel as per specification.

ITEM No. 344 :- S. S. Enclosure (5.11.18) Supplying and erecting SS enclosure for MCCB suitable for 125A to 200A MCCB.

ITEM No. 345 :- Arm. cable 3½ core 95 sq. mm. (7.1.19) Supplying, erecting and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands and lugs, on wall / trusses / pole or laid in provided trench / pipe as per specification.

ITEM No. 346 :- Copper earth Plate (9.1.2) Providing earthing with copper earth plate size 30 x 30 x 0.315 centimetre complete with all materials, testing and recording the results as per specification.

ITEM No. 347 :- Copper Strip (9.2.2) Supplying and erecting copper strip of high purity required size used for earthing on wall and / or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint with joints required as per specification.

ITEM No. 348 :- 82.5 KVA D.G. Set (11.1.11) Supplying, erecting, testing and commissioning of diesel generating set with alternator of 82.5 kVA output continuous rating, 3 Phase, 415 V, 50c / s 0.8 p.f. A.C supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation + / - 5 %, with performance class G2 and maximum fuel consumption 14.0 Litres per hours @ 75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires / cables, the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0 metre, provided with first filling of oil, diesel not less than 145 Litres etcetera on provided M20 Grade CC Foundation as per specification.

ITEM No. 349 :- AMF Panel (11.2.9) Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of above 62.5 kVA up to 82.5 kVA capacity Three phase, 415 Volts, 50Hz A.C. with all standard features, safeties etcetera as per specification

ITEM No. 350 :- Excavation (16.1.7) Excavating soft murum / soft soil road by chiselling for preparing pit for poles stay or earth plates or for laying cables, pipes and clearing the site by removing debris and making the site good complete.

ITEM No. 351 :- Cement concrete Foundation (16.3.7) Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) millimetre stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

ITEM No. 352 :- (1.2.8) Supplying and erecting PVC trunking (PVC casing-n-capping) of size 32 millimetre with accessories on wall / ceiling as per specification.

ITEM No. 353 :- (1.3.1) Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit / trunking / inside pole / Bus bars or any other places as per specification.

ITEM No. 354 :- (1.6.1) Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

ITEM No. 355 :- (1.6.11) Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

ITEM No. 356 :- (1.6.23) Supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

ITEM No. 357 :- (1.6.28) Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module duly erected.

ITEM No. 358 :- (1.7.25) Wiring for plug on board with flush Switch socket, copper wiring and earthing as per specification.

ITEM No. 359 :- (1.7.19) Point wiring for light / bell / exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification.

ITEM No. 360 :- (1.7.20) Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification.

ITEM No. 361 :- (2.1.15) Supplying and erecting bulk head LED fitting maximum 10W with high transitivity diffuser with system lumens output of minimum 1100 lumens, min. efficacy of 110 lumen / W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty.

ITEM No. 362 :- (2.1.22) Supplying and erecting inverter LED batten 20W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, minimum 2600 mAh Lithium ion Battery with charging time of 8-10 Hours and backup time of Minimum 3 hrs with minimum 25% of initial Watts having luminous efficacy of 100 lumen / watt, CRI>80, CCT of 6500K and THD<=20% having useful life of minimum 25000 hrs with overheating protection with 2 years warranty.

ITEM No. 363 :- Exhaust Fan (2.10.14) Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 225 millimetre 1400 RPM rust proof body and blades, wire mesh, duly erected, complete.

ITEM No. 364 :- Energy Saving Ceiling fan (2.10.22) Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 millimetre, maximum energy consumption of 28W having service ratio (CMM / W) of Min. 8, PF>0.9, THD<10% with IR remote control / compatible speed regulator, Temperature Rise of Max. 40 deg. C, having external mounted control PCB completely erected in position as per specification

ITEM No. 365 :- (5.3.9) Supplying, erecting and marking DPMCB 40A to 63A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification

ITEM No. 366 :- (5.6.6) Supplying, erecting and commissioning 4 pole RCCB 63A, electromagnetic type with 30 / 100 / 300 mA sensitivity with earth leakage trip indication complete as per specification.

ITEM No. 367 :- (5.4.13) Supplying and erecting CRCA sheet metal one way enclosures of 1.2 millimetre thickness suitable for DP MCB / TP MCB / FP MCB / RCCB / RCBO complete erected on angle iron / GI frame.

ITEM No. 368 :- (5.11.17) Supplying and erecting SS enclosure for MCCB suitable for up to 100A MCCB.

ITEM No. 369 :- (7.2.20) Supplying, erecting and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 2 core 6 sq. mm. copper conductor complete erected with glands and lugs, on wall / trusses / pole or laid in provided trench / pipe as per specification.

ITEM No. 370 :- (7.1.15) Supplying, erecting and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 25 sq. mm. aluminium conductor complete erected with glands and lugs, on wall / trusses / pole or laid in provided trench/ pipe as per specification

ITEM No. 371 :- (9.1.1) Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 centimetre complete with all materials, testing and recording the results as per specification.

ITEM No. 372 :- (17.1.2) SITC of Electric Traction Passenger Lift with · Rated capacity :- 10 Passenger / 680 Kgs · Floors :- G+2 floor (3 Stops / 3 Landings) · Travel :- 3 to 9 metres · Location of Lift Machine:- MR / MRL · Rated speed :- 1.0 mps VS · Car / Landing door clear opening of 800 millimetre wide x 2000 millimetre high · Clear Car size of 1300 millimetre wide x 1350 millimetre deep x 2250 millimetre high · Lift shaft available having clear size of 1770 millimetre wide x 2960 millimetre deep, 1500 millimetre Pit depth, ………mm Overhead. · Doors type :- COPO / TOPO Doors with frame made from SS 304 grade solid (non-cladded) sheet of 1.5 millimetre thick in hairline finish for car and all landing doors with SS door architraves / frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory). · Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5 millimetre, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower / fan for ventilation and SS chequered plate flooring, handrails, mirror, emergency light etcetera The lift car interior design shall be done as per the directions of engineer in charge. · COP with SS face plate having metallic push buttons with Braille code and luminous indicator around button with FPI, scrolling UP / DN LED indicator and with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi and English with intercom system with telephone instrument in Lift car, LMR and FCC / ground floor. · LOP with SS face plate having recess / surface push button box for all landings with scrolling UP / DN LED indicator having metallic push buttons with Braille code and luminous indicator around button with CPI, Lift car arrival and next travel direction audio-visual indication at all landings. · Lift controller based on micro-processor / PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as over current, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etcetera various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open / close operation from COP etcetera The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters. The control panel duly wired with proper size and strength, copper wire for power and control circuit, with provision for addition of floor / control card and allied accessories control panel having enclosure of 1.5 millimetre CRCA sheet with powder coating with IP54 Protection class. · ARD complete with necessary SMF VRLA batteries. · Fireman controller having fireman switch at fire Landing. · CCTV surveillance system comprises of 2 numbers minimum 2.0 MP FHD IP based vandal proof Dome camera in lift car and in LMR / inside lift shaft top aimed on Lift machinery and controller with NVR kept in LMR / FCC with HDR data backup for min. 90 days with minimum 18” FHD TV monitor, to be kept in FCC / LMR as directed by Engineer in charge. · Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts / hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor / shaft walls complete with main / diverter traction sheaves, suspension wire ropes / belts of adequate size and strength. · Other mechanical parts such as 'T' section adequate size guide rails for car and counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etcetera erected with necessary steel work. · Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etcetera complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required and scaffolding for erecting guide rails, providing and fixing steel girders / RCC work having adequate strength for mounting and hoisting lift machine etcetera complete as per specification · General : - Job includes entire procedure of obtaining all necessary erection permissions and "License to Work the Lift" from Electrical Inspector (Lifts) with submission to the Engineer in Charge. · The above rate includes Fully Comprehensive AMC for one year from the date of commissioning.

TOTAL : (ii) Electrical Work

TOTAL : (i) Civil Work

TOTAL : (ii) Electrical Work

TOTAL : PART – A (Work Portion)

D S Halkude