Construction of Phase A work at JNV South West Khasi Hills Meghalaya reg supplying and installation of furniture work

Amount

School Building

Supply & installation Big Desk (for two persons)-The overall dimensions of desk will be 1066mm * 930mm * Height 760mm, complete as per Specifications enclosed and direction of Engineer-in- charge having the Table top shall be made up of 18.0 mm thick plywood IS 303 of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish). Table top dimensions shall be W 850 mm x D 380 mm. Edge bench shall be post formed with round edge. The remaining three edges must be sealed with 2mmthick PVC edge banding tape. Edge band must be trimmed on edges and corners. The desk shall be Greenguard certified for low chemical emission of VOCs (Voltage Organic Compounds) and carcinogens, contributing to a healthier room environment. Valid certificate to be submitted along with the bid. Make Of plywood : Merino / Greenply / Century / Kitply. Make Of Laminate & balancer : Marino / Greenlam / ASIS / Century following specifications. Seat and back rest shall be made Of 18mm thick plywood of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish) except back rest. Back rest shall be have both sides colour lamination. Technical details of seat and back rest are mentioned below:Seating bench dimensions shall L 900 mm x W 300 mm. Front side shall be rounded with post forming. Remaining three edges shall sealed with 2mm thick PVC edge banding tape. Back rest dimensions shall L 900 x H 200 mm Upper side shall be rounded with post forming Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. Desk Shelve shall be made of prime quality 0.8mm thick CRCA sheet of H150mmxD300mm and side stiffeners of MS CRCA tube size 19mmx19mmx1mmthick. One vertical support (partition) Of square tube size 25mm square xl.2mm thick must be provided at centre of tray . Upper moedsty made of prime quality 0.8mm thick CRCA Sheet Powder Coated should be embossed with dimples in round shape, height will be 150mm, there should be Perforated lower modesty Made of prime quality 0.8 mm thick CRCA sheet of size H150mmXD21mm with square perforation, CRCAT ube Of size 19x19x1mm thick to be inserted for full length at bottom Of Jali . Bag hook should be provide on both side of piller made of minimum 4mm dia rod Side frame structure:- Made of prime quality CRCA pressed form section 165mmx25mmx1mm

Supply & installation Medium Desk (for two persons)-The overall dimensions of desk will be 900mm W± 5 X 890mm D± 5 X 688/420mm H± 5, complete as per Specifications enclosed and direction Of Engineer-in- charge having the Table top shall be made up Of 18.0 mm thick plywood IS 303 of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish). Table top dimensions shall be W 850 mm x D 380 mm. Edge towards bench shall be post formed with round edge. The remaining three edges must be sealed with 2mmthick PVC edge banding tape. Edge band must be trimmed on edges and corners. The desk shall be Greenguard certified for low chemical emission of VOCs (Voltage Organic Compounds) and carcinogens, contributing to a healthier room environment. Valid certificate to be submitted along with the bid. Make Of plywood : Merino / Greenply / Century / Kitply. Make of Laminate & balancer : Marino / Greenlam / ASIS / Century following specifications. Seat and back rest shall be made of 18mm thick plvwood of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish) except back rest. Back rest shall be have both sides colour lamination. Technical details of seat and back rest are mentioned below:Seating bench dimensions shall L 900 mm x W 300 mm. Front side shall be rounded with post forming. Remaining three edges shall sealed with 2mm thick PVC edge banding tape. Back rest dimensions shall L 900 x H 200 mm Upper side shall be rounded with post forming Remaining three edges shall be sealed with 2mm thick. PVC edge banding tape. Desk Shelve shall be made of prime quality 0.8mm thick CRCA sheet of H150mmxD300mm and side stiffeners of MS CRCA tube size 19mmx19mmx1mmthick. One vertical support (partition) of square tube size 25mm square xl.2mm thick must be provided at centre Of tray . Upper moedsty made of prime quality 0.8mm thick CRCA Sheet Powder Coated should be embossed with dimples in round shape, height will be 150mm, there should be Perforated lower modesty Made Of prime quality 0.8 mm thick CRCA sheet Of size H150mmXD21mm with square perforation, CRCAT ube of size 19x19x1mm thick to be inserted for full length at bottom of Jali . Bag hook should be provide on both side Of piller made Of minimum 4mm dia rod Side frame structure:- Made Of prime quality CRCA pressed form section

a) Dimensions and Configuration : Total Width of the Setup: Minimum 12 feet. Height: Approximately 4 to 4.5 feet from the board surface. b) Sliding Boards: Quantity. 2 (Left and Right). Size (Each Board): 6 feet (W) x 4 feet (H). c) Material: Left: Green chalkboard (matte surface, suitable for chalk) Right: Whiteboard (glossy surface, suitable for dry-erase markers) d) Function: Boards shall slide horizontally on a top and bottom aluminium/steel channel track to fully cover or reveal the IFP as needed. e) Interactive Flat Panel IFP : Position: Centered within the frame and between the two sliding boards. Mounting: Wall-mounted securely inside the board structure, with space allowance for ventilation and service access.IFP Opening Size: Sized appropriately to the IFP being installed (contractor to confirm model and dimensions). f) Frame Material: Laminated plywood or MDF with a natural wood finish or laminated color finish (as per architect/owner approval). g) Frame and Track System : Material: Aluminium or powder-coated steel tracks with smooth sliding mechanism.Top & Bottom Rails: Tracks shall be aligned and reinforced to ensure boards move easily and without wobble.Finish: Durable, corrosion-resistant coating suitable for indoor use. h) Additional Requirements All boards and the structure must be securely fixed to the wall with appropriate fasteners. Provision for cable management must be included for the IFP (i.e., concealed conduit/path for power and data cables).The unit must be free from sharp edges, splinters, or any protruding parts that could cause injury.Installation height should ensure comfortable writing access for average adult and student height (typically bottom edge —2.5 to 3 feet from the floor.

KITCHEN AND DINING

a) Dining Table: SS Dinning Table consists of Dinning Top is made up of I mm thickness Stainless steel sheet ofSS 304 Grade with overall dimension of 1800(L) X 700(D) X 750(H). The table top is reinforced with a 18 mm ply Board on Stainless steel frame of square section 40mmx40mmx1.6mm. Dinning top of stainless steel sheet shall be extended to the sides and a depth upto 40 mm under the table top in all directions including edge rounding, grinding and finishing etc. all complete. The Table top shall finish in such a manner to avoid any sharp edges. The table will be supported by four hollow legs made from SS 304 grade stainless steel. The hollow legs shall be of square type of size These legs shall be securely welded or mechanically fastened to the underside of the tabletop frame. For additional structural stability, stainless steel cross supports shall be provided between the legs as shown in figure with 40mmx40mmx1.6mm SS square section. The table shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The design shall prioritize user safety with no sharp corners or edges. The table must be structurally sound and capable of supporting a uniformly distributed load of at least 250 kg. All materials used must conform to relevant IS standards, and the finished product should be free from burrs, dents, or deformities.

b) Dining Bench: The Bench shall be of size 1800 mm in length, 300 mm in depth, and 450 mm in height, suitable for use in residential schools. The bench top shall be made of 18 mm thick plywood + Laminated , finished with a 0.8 mm thick decorative laminate on the top surface, and a balancing laminate backing on the underside to ensure dimensional stability. All exposed edges shall be sealed with PVC edge banding or machine-finished to prevent splinters and enhance durability. The plywood shall be scratch-resistant, water-resistant, and easy to clean, with a light woodgrain or equivalent finish as approved. The supporting frame shall be fabricated frame of square section 40mmx40mmx1.6mm MS Pipe in Powder Coated. These legs shall be securely welded or mechanically fastened to the underside of the benchtop frame. The bench shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The design shall prioritize user safety with no sharp corners or edges. The bench must be structurally sound and capable of supporting a uniformly distributed load of at least 250 kg. All materials used must conform to relevant IS standards, and the finished product should be free from burrs, dents, or deformities

BOYS AND GIRLS DORMITORIES

Providing and installing 18 mm HDHMR boards on existing RCC and Cement plaster brick walls with the help of counter sink fasteners in plump and level. All edges to be rounded. Imm laminated should be pasted on all visible areas and edges polished to match the laminate shade.

M/S VICTOR SUJA (BID ID -4481)