REPAIR TO BLDG AND PERIODICAL SERVICES IN VARIOUS UNITS AT JWG AND REPAIR TO HARD STANDING, BDY WALLS, PATHS, DRAINS, FENCING AND PROTECTIVE WORKS AT JWG AND REPAIR/ REPLACEMENT TO E/M INTERNAL FITTINGS/ FIXTURES AND WIRING IN VARIOUS UNITS AT KG TOP

Amount

B&R PORTION:- M&L for preparation of old plastered/ un-plastered wall surfaces , and applying one coat of white wash on walls including cornices, pilasters etc, complete all as specified and directed.

M&L for complete removal of existing treatement and applying two coats of white wash on wall, complete all as specified and directed.

M&L for complete removal of existing treatement and applying one coat of colour wash on wall, complete all as specified and directed.

M&L for preparation of old plastered/ un-plastered surfaces of wall, ceiling, roof projection, chajjas, facia etc and applying one coat of oil bound distemper (any tint), complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or any tint, complete all as specified and directed.

M&L for preparation of old surfaces and applying one coat of cement base paint on wall and AC sheet roof surfaces, complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying two coats of cement base paint, complete all as specified and directed.

M&L for preparation of old painted surfaces of wood or wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of Ist quality, complete all as specified and directed.

M&L for preparation of old painted steel surfaces/CGI/PGI sheets of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern, complete all as specified and directed.

M&L for applying wall care putty of approved make 3mm thick on walls as per manufacturer's instructions with and including rubbing by means of sand paper to have smooth finishing to receive primer / paint, complete all as specified and directed.

M&L for preparation of old plastered/ un-plastered wall surfaces and applying one coat of weather proof water based exterior paint any tint as approved by GE on walls, roof/chajjas, facia including cornices, pilasters etc, complete all as specified and directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) n. exc 30cm high with synthetic enamel paint including oblitering old writing of any description to match existing work, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone/ concrete, glazed with putty or fixed with beads, complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, Complete all as specified and directed.

Dismantling PVC water tanks and removing to store of capacity not exceeding 500 ltr complete all as specified and directed.

Dismantling PVC water tanks and removing to store of capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified and directed.

Dismantling of plain or corrugated steel or AC sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Dismantling of timber scantling 40sqcm and over in section, as in any position, complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed.

Dismantling of timber scantling under 40sqcm in section unframed work as in fillets, rails, posts, rafters, purlins etc, complete all as specified and directed.

S&F 4 mm thick E-board (Classic) including fixing of frame work made up of special MS section, galvanized sheet with zinc coating cellular intro painting and consisting of angle cleats of size 25 mm wide, 1.6 mm thick with flag fixing to the ceiling with dash fastener 12.5 mm x 40 mm long or with 2 mm dia GI wire or fixed with bolts in GI channel main of size 35x25x0.5 mm thick and cross runner of size 25x25x0.5mm for fixing E-board of size 600x600mm x4 mm thick including fixing of E-board with ceiling section and perimeter of channel 25x25x1mm thick, 27mm high flange of 20mm to 30mm long extra including application of two coats of oil emulsion distemper, complete all as specified and directed.

S&F in repair 12mm thick both sides prelaminated particle board, medium density fixed with screw to frame work in cup board shutters, partitions, shelves etc acomplete all as specified and directed.

S&F 0.63mm thick galvanised corrugated mild steel sheeting with grade of zinc coating of 275 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with L or J type or cranked hook bolts, in roof, walls etc, complete all as specified and directed.

S&F 0.80mm thick plain galvanised mild steel sheeting with 275 gm/sqm zinc coating as in ridge , hips, valley gutters, drip and straight flashing(length and girth as fixed) fixed with L hooks or cranked bolts, in roof etc., complete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, valley gutter and similar works fixed with self tapping screws complete all as specified.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plate confirming to Fe 410W(Gde E-250), quality 'A' complete all as specified and directed.

S&F mild steel work as in wind ties for roof including securing bolts, including all necessary drilling, bolting or riveting etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F 2nd class soft wood (Kail) as in scantling, clean sawn fixed in unframed work, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 m in length) as in plinth protection, finished the surfaces even & fair, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base floor finishing surface even and fair, complete all as specified and directed.

M&L for cement concrete (1:2:4) type-B-1 (using 20mm graded stone crushed aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, bed block, kneelers, apex stones, bed plates, roof kerbs round or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for chequered cement concrete tiles 300x300x 25mm thick, set, jointed and pointed with mixture of white and grey cement in equal proportion and no pigments, laid over and including 20mm thick screed bed in CM 1:6,complete all as specified and directed.

M&L for vitrified ceramic tiles, light shade, 10 mm thick (square/rectangular) area of each tile not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

All as per ser item No.40 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.18Sqm but n exc. 0.38Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

All as per ser item No.42 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for glazed ceramic coloured tiles (300x200mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

M&L for walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

All as per item No. 47 above, but except stone complete all as specified and directed

M&L for 15mm thick cement plaster rendering in CM 1:4 on fair faces of bricks or concrete surfaces, chajja and suspended work & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint oven and incl alkali resistant primer, complete all as specified and directed.

M&L for preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil emulsion distemper over and including 1 mm thick wall care putty, complete all as specified and directed.

Taking down shutters of any description exceeding 1sqm and not exceeding 2sqm each, complete all as specified and directed.

Taking down shutters of any description exceeding 2 sqm each, complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm and not exceeding 4 Sqm each, complete all as specified and directed.

S&F 2nd class hard wood, plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc.divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

All as per Srl item No. 59 Above but 30 mm thick for window/ ventilators complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site complete all as specified and directed. Note:- Cadmium screws to be used for fixing of fixtures & fittings.

Taking down aluminium door shutters of any description and refixing in the same opening for making good where unsv hinges, other fittings etc have been removed from frame & replace it including oiling / repairing if required, complete all as specified and directed.

S&F in repair door closer hydraulically regulated (Aluminium extruded section body) , designation No 3 universal type suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled,75mm long, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section of size 100mm and fixed, complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 100mm and fixed, complete all as specified and directed.

S&F 250mm long aluminium alloy anodized sliding door with haps, staple (bolt type) and fixing clips of sheets, cast or extrusted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading, complete all as specified and directed.

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer, complete all as specified and directed.

S&F sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

S&F figured glass pin headed type, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

S&F in repair MS powder coated tubular curtain rod fancy type of 25mm dia complete all as specified and directed.

S&F in repair MS powder coated decorative type bracket, end ball, rounded block, bracket (coated with brown/cherry/golden colour) suitable for 25mm dia curtain rod of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed.

M&L for plain cement Concrete 1:3:6 type-C1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work, complete all as specified and directed.

S&F steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F steel water tubing 20mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified and directed.

S&F in repair bib tap 15 mm bore with flange, brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. Make:- Jaquar cat part No CON-047KN or equivalent cat part of make as specified in P.S.

S&F in repair angular stop valves cast copper alloy 15 mm dia, chromium plated with wall flange screwed down, high pressure, with capstan head screwed both ends for iron pipes or for unions complete all as specified and directed. Make-Jaquar Cat Part No:-CON-059KN or Equaivalent cat part of make as specified in P.S.

S&F in repair vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed. Make:- Prayag cat part No4054 or Equaivalent cat part of make as specified in P.S.

S&F in repair PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints complete all as specified and directed. Make:- Prayag cat part No 501 or Equaivalent cat part of make as specified in P.S.

S&F in repair vitreous china wash hand basin, white, flat back, size 580x450 mm excluding taps, waste, chain & plug and porcelain stopper but including brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 450mm complete all as specified and directed.

S&F in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe complete all as specified and directed. Make:- Jaquar cat part NoCON-011KN or equivalent cat part of make as specified in P.S.

S&F in repair 32mm dia PVC waste pipe 800mm long complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe including clamps, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe(vent pipe) including clamps, complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type of size 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repair grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), suitable for floor taps, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs incl with 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs incl with 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and as directed.

S&F in repair chromium plated hand shower (Health faucet) with 1.5m long flexible tube of stainless steel in chrome finish and wall hook complete all as specified and directed. Make: Jaquar code No ALD-CHR-583 or equivalent of make as specified in PS.

S&F in repair CP jet spray with holder including 1.5m long PVC/Chromium plated flexible PVC pipe, necessary nut bolts and PVC washers fixed with PVC seat cover for pedestal pattern water closet, complete all as specified and directed.

S&F in repair plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised or PVC hinging device complete all as specified and directed.

S&F in repair 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head,screwed both ends for iron pipe complete all as specified and directed.

S&F in repair PVC water tank cover suitable for 500ltrs/1000ltrs water tank, complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground posts embedded in concrete complete all as specified and directed.

Taking down carefully old galvanised stranded steel barbed wire from old RCC posts and removing from site complete all as specified and directed.

Demolition of reinforced concrete in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (40mm graded aggts) as in foundation and mass concrete where required as per direction of Engineer-in- charge complete all as specified and directed.

M&L for MS work for fencing post and struts made from angle iron and flat iron in any section including cutting tops to shape , drilling holes and notching for fixing of wires etc confirming to Fe -290 or Fe -330, complete all as specified and directed.

S & F galvanised 2 strand, steel barbed wire, 2.20mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, includdigng, securing or tying at crossings with and provisiion of galavnised (Zink coating 60 gsm) mild steel wire, staples or steel pins, etc as directed each line wire to measured complete all as specified and directed.

Supply only chain link MS zink coated 60gm/sqm as per IS 4826 fencing of any mesh size and 3mm dia of wire complete all as specified and directed. NOTE: This item shall be measured and paid as per actual weight or standard weight as per SSR which ever is less.

Fixing only chain link fencing including line wire, any mesh size and any type of standards rails straining bolt etc including provision of binding wire complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for TMT bars 6mm to 8 mm dia and cut to length bent to shape and binding with MS wire (annealed) not less than 0.9mm Dia complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,length of bolt 5 to 10 cm long and dia of neck not exc 15 mm complete all as specified and directed.

S&F concertina coil made to shape as dia exc 450 mm but n exc 600 mm put on top of wall in between Y shaped angle iron post and secured with necessary binding wire complete all as specified and directed by Engr in charge.

M&L for boulder filling hand packed tightly (any thickness) at back of walls over arches etc, and raising (or lowering) to the required level compete all as specified and directed.

M&L for rendering 20 mm thick in cement mortar 1: 4 on other than fair faces of brick work or stone masonary surfaces, chajja and suspended work finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, chajja and suspended work finished even and smooth without using extra cement, complete all as specified and directed.

M&L for raking out joint/pointing to random rubble or polygonal rubble stone masonry uncoursed or brought upto courses built in CM complete all as specified and directed.

M& L for raised pointing in cement mortar (1:4) brought upto courses built in CM complete all as specified and directed.

S&F framed work such as grills, gratings, steel gate , purlin etc., with ends of bars shouldered and/or riv-eted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 gde E-165 complete all as specified and directed.

M&L for providing precast cement concrete 1:3:6, type C-1 (using 20 mm graded crushed stone agg) as in PCC bonders set in CM 1:6 complete all as specified and directed.

M&L for reinforced cement concret (nominal mix) type B-1, 1:2:4 (20mm graded aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likecomplete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams for flat rough finished surface etc, complete all as specified and as directed.

S&F in repair Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in floor/hardstanding finishing cement concrete surface etc complete all as specified and directed.

M & L for plain cement concrete 1:2:4 type B-2, using 40mm graded crushed stone aggregates as in surfaces channels and drain complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner grith in cement concrete, using extra cement including forms, moulds mitred/stopped ends etc. complete all as specified and directed.

M&L for 75mm thick PCC 1:8:8 type D2 (using 40 mm graded stone aggregate) as in sub base to chequered/interlocking tile, complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 80mm thickness M-40 Grade,laid jointed pointed with grey cement and no pigments, complete all as specified and directed by Engr-in-Charge. Note: The sample shall be got approved by GE before bulk procurement & lot shall be got tested independently by the GE.

M&L for sand filing including spreading and leveling not exc 25cm thick under floor complete all as specified and directed.

E&M PORTION:- Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan point controlled by one way switch 6 Amp complete all as specified and directed.

One light point controlled by two, two way switch 6 Amp complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed.

One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed.

One bell point controlled by one way switch 6 Amp complete all as specified and directed.

All as per srl item No 132 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire complete all as specified and directed.

S&F in repair ceiling rose, 3 terminal, surface bakelite 65 mm x 50mm, PVC/poly carbonate, insulated body, complete all as specified and directed.

S&F in repair switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed.

S&F in repair switch piano flush type 6 Amp two way, (ISI marked), complete all as specified and directed.

S&F in repair switch piano bell push flush type 5 Amp single pole one way (ISI marked) complete all as specified and directed.

S&F in repair socket outlet 2 in 1, 3 pin, 5 Amp flush type universal, complete all as specified and directed.

S&F in repair Switch socket multipurpose combination 2 in 1, 5 pin, 6 Amp flush type universal, complete all as specified and directed.

S&F in repair Switch socket outlet multipurpose combination 2 in 1, 6 pin, 5 and 15 Amp flush type universal, complete all as specified and directed.

S&F in repair Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

S&F in repair stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified and directed.

S&F in repair electric bell ding dong type 230 volts AC supply 50 Hz complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Inverter LED batten 20W with square profile and polycarbonate channel, lithium Ion battery with charging time 8 Houres-10 Houres and backup time upto 4 Houres with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make- Havellas Cat part No LHEXACPFN1W020 OR equivalent of make as specified in PS.

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. all as specified and directed.

S & F in repair LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F in repair surface mounted square/round type decorative LED light fittings 15 watt connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F in repair surface/ceiling mounted square LED light fittings, 15/18 W LED with prewiring complete all as specified and directed.

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F in repair gate light fittings, outdoor type, high power , 25 watt, IP65 luminaire, prewired with suitable pole for mounting complete all as specified and directed. Make: Havells cat part No. Coral Opal IP65 or equivalent make as mentioned in PS

Supply and fixing in repair LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply and fixing in repair inverter LED bulb 9 watt including all connected items, complete all as specified and directed. Make : Havells cat part No. LED 9 W INVERTER BULB B22 CDL or equivalent make as specified in PS

S&F in repair LED driver suitable for 34 watt LED ceiiling light fittings and making connection to fitting complete all as specified and directed. Make:-Havells cat part No-LEDDRIVER36V36WS or Equivalent cat part of make as specified in Appx 'A' to P.S.

S&F in repair single pole and neutral enclosure with a two pin and metal earth plug and socket complete with & incl one single pole MCB of 20 Amps complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, TPN double door (IP43), 4 ways built in bus bars suitable for 415 volts, AC, 50 Hz and suitable for FP MCB as incommer and out going SP/TP MCBs complete all as specified and directed. Note:- MCBs shall be measured and paid separately.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 4 ways built in bus bars suitable for 240 volts, AC, 50 Hz , including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 12 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair MCB TPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCTNF040 - DHMGCTNF063 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB SPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCSNF040 - DHMGCSNF063 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series complete all as specified and directed. Make:-Havells cat part No-DHMGCSPF006-032 or Equivalent cat part of make as specified in P.S.

S&F in repair Switch socket combination 5 in 1, 5 pin, 16/20 Amp incl box with 4 fixing holes, complete all as specified and directed.

S&F in repair Switch socket combination 5 in 1, 5 pin, 6 Amp incl box with 4 fixing holes, complete all as specified and directed.

Taking out old unsv exhaust fan from site and replacement of exhaust fan made up of sturdy engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, 1200 RPM, copper winding of sweep 250mm incl all connecting accessories complete all as specified and directed by Engineer-in-charge.

Taking out old unsv exhaust fan from site and Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed by Engineer-in-charge.

Taking out old unsv exhaust fan from site and Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450mm sweep with, blades, and frame and louvers complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC casing caping of size 25 mm incl all fixing accessories complete all as specified and directed.

S&F Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

S&F in repair Sub main wiring with single core cable 2x 6 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 6 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 6 Sqmm and one run of pvc conduit/casing caping shall be measured as one unit.

S&F in repair Sub main wiring with single core cable 2x 4 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 4 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 4 sqmm and one run of PVC conduit/casing caping shall be measured as one unit.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat or circular of size 6 Sqmm 2 core & including taking down old old unsv service cable connection, complete all as specified and directed.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat of circular of size 10 Sqmm 2 core including taking down existing old service connection, complete all as specified and directed.

Repair and maintenance of unserviceable ceiling fan of 1200mm/1400mm sweep at contractor's work shop, incl dismantling complete the ceiling fan parts, inspecting serviceability of all the parts, refixing of serviceable parts after cleaning and replacement of unserviceable parts with company's genuine parts i.e. capacitor, bearing, bushes, shaft, bracket, rubber bush, connecting wire, PVC connector, aluminium clamp for rod, bracket, bush rod, greasing/oiling etc assembling, cleaning and testing of ceiling fan complete all as specified and directed. Note: (i) Unserviceable parts as above shall be measured and paid separately under relevant items of Sch 'A' item No 174 to 179 as supply only. (ii) Rewinding of stator will be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. Cotter pin, screws shall be deemed to included in the cost of quoted rate.

Supply only bearing good quality for ceiling fan 1200mm/1400mm sweep ISI marked complete all as specified and directed.

Supply only Gun metal bush for ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply only capacitor 2.5 mfd ISI marked complete all as specified and directed.

Supply only brass bracket assy for hanging the ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply only 3 core flexible wire 40/.0076, white colour from ceiling rose to fan connector complete all as specified and directed.

Supply only stator shaft for ceiling fan complete all as specified and directed.

Supply and fixing in repair ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200/1400 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

M&L for removing of old burnt winding of any size , type and rewinding of stator winding with superior quality copper wire with insulation complete all as specified and directed.

Repair and maintenance of unserviceable exhaust fan of any cap and sweep by dismantling the exhaust fan parts, inspecting the serviceability of parts, refixing of serviceable parts after cleaning, replacement of unerviceable parts i.e. beaing, bush, capacitor, connecting wires, fan blade, locknut, rubber pad etc, oiling/greasing, cleaning and testing of exhaust fan complete all as specified and directed. Note: (i) Unserviceable parts replaced shall be measured and paid separately under relevant items of Sch 'A' item No 183, 184 & 187 as supply only. (ii) Rewinding of stator winding shall be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. screws shall be deemed to included in the cost of quoted rate.

Supply only double ball bearing (ISI marked) for exhaust fan of 200 mm sweep to 450 mm sweep fan complete all as specified and directed.

Supply only gun metal bush for Exhaust fan of any capacity. complete all as specified and directed.

M&L for rewinding of 450mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

M&L for rewinding of 300mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

Supply only blade of exhuast fan of 200 mm sweep to 450 mm sweep as per existing make complete all as specified and directed.

NATIONAL TRADING COMPANY

M/S BADRI NATH GUPTA

M/S KEWAL KRISHAN SANJEEV KUMAR VAID

M/S BHATT TRADERS

VIKAS ENTERPRISES