Construction of aryabhatt Community hall Nagar Parishad, Khagaul Motichauk khagaul patna

NIT- 06/2025-26 Group.-01

BILL OF QUANTITY FOR

Construction of Aryabhatt Community Hall. Nagar Parishad, Khagaul, Motichauk, Patna.

(1) Amount of BOQ : Rs. 21,76,68,52.00

(3) Cost of Earnest Money : Rs. ,43,54,00.00

Sl. No. SOR Name of Items Quantity Per. Rate Tendered Amount

In Figures In Words

1 0L01 Bcd Providing unskilled labour for site clearance levelling and layout etc. all complete job as per building specifications and direction of E/I. Rupees Four Hundred Fifty Eight Only

2 20.2.1 Bcd Boring-providing and installing bored cast-in-situ reinforced cement concrete pile of grade M-25 specified diametre and length below the pile cap in cement 1:1 1/2:3 (1 cement : 1 1/2 coarse sand : 3 graded stone aggregate 20 mm nominal size) to carry a safe working load not less than specified, excluding the cost of steel reinfrement but including the cost of boring with casting and / or bentonite solution and the length of the pile to be embeded in the pile cap (Length of pipe for payment shall be measured upto to the bomeasured upto to the bottom of pile cap) 300 mm dia piles all complete as per building specifications and direction of Engineer-in-Charge. Rupees Nine Hundred Two And Paise Sixty Only

3 2.8.1 Bcd Earth work in excavation in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m : All Kinds of soil all complete as per building specifications and Extra for every additional lift of 1.5 m or part thereof in All kinds of soil all complete as per building specifications and direction of Engineer-in-Charge. Rupees Three Hundred Sixty And Paise Seventy Only

4 2.28. Bcd Supplying and filling in plinth with local sand and under floors including watering, ramming consolidating and dressing all complete job as per specification and direction of Engineer-in-Charge. Rupees Two Hundred Eighty Seven And Paise Thirty Only

5 11.72. Bcd Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes. Royalty all complete job as per building specification and direction of Engineer-in-Charge.. Rupees Two Hundred Eighty Three And Paise Thirty Only

6 4.1.3 Bcd Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinth level : 1:2:4 (1 cement : 2 Coarse Sand : 4 Grade Stone Aggregate 20 mm nominal size) etc. all complete as per building specifications and direction of E/I. Rupees Three Thousand Nine Hundred Ninety Eight And Paise Ten Only

7 5.33.1.1 Bcd Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of

concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works up to plinth level Concrete of M-25 grade with minimum cement content of 330 kg/cum etc.all complete as per building specifications and direction of E/I Rupees Five Thousand Sixty Three And Paise Forty Only

8 5.33.2.1 Bcd Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of

accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for

the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All work above Plinth level upto floor V Level. Concrete of M-25 grade with minimum cement content of 330 kg/cum etc.all complete as per building specifications and direction of E/I. Above Plinth Level Rupees Five Thousand Eight Hundred Sixty Three And Paise Twenty Only

9 5.22.7A Bcd Providing Reinforcement for R.C.C. work including straightening, cutting bending, placing in position and binding all complete. Thermo-Mechanically Treated bars (TMTC-500) 8 mm dia etc. all complete as per specification and direction of E/I. Rupees Ninety Four And Paise Fifty Only

10 5.9.1 Bcd Providing centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of column etc. for mass concrete etc. all complete as per building specifications and direction of E/I. Foundation Rupees Two Hundred Eleven And Paise Sixty Only

A Foundation & Upto Plinth Level 105.00 m² 211.60 22218.00

5.9.5 Bcd Providing centering and shuttering including strutting, propping etc. and removal of form for Lintels, Beams, plinth beams, girders, bressumers and cantilevers etc. all complete as per building specifications and direction of E/I. Lintel Rupees Four Hundred Four And Paise Seventy Only

B Tie Beam / Plinth Beam - 196.14 m² 404.70 79378.00

5.9.6 Bcd Providing centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts etc. all complete as per building specifications and direction of E/I. Column Rupees Four Hundred Ninety Four And Paise Forty Only

5.9.21 Bcd Providing centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick etc. all complete as per building specifications and direction of E/I. Lintel Rupees Five Hundred Eighteen And Paise Ninety Only

5.9.20 Bcd Providing centering and shuttering including strutting, propping etc. and removal of form for Wheather shade, Chajjas, corbels etc. including edges etc. all complete as per building specifications and direction of E/I. Chajja Rupees Five Hundred Forty Four And Paise Sixty Only

5.9.21 Bcd Providing centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick etc. all complete as per building specifications and direction of E/I. Lintel Rupees Five Hundred Eighteen And Paise Ninety Only

F Lintel Band Beam - 128.09 m² 518.90 66466.00

5.9.19 Bcd Providing centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc. including edges all complete as per building specifications and direction of E/I. Chajjas Rupees Five Hundred Fifty And Paise Ninety Only

5.9.16.1 Bcd Providing centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and brreaks on floors and walls Under 20 cms wide etc. all complete as per building specifications and direction of E/I. Rupees One Hundred Thirty And Paise Twenty Only

H Edged of Slab - 228.44 m 130.20 29743.00

11 6.1.14C Bcd Providing Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand) etc. complete job as per building specifications and direction of E/I. Rupees Four Thousand Nine Hundred Twenty Three Only

12 6.1.14C + 6.3C Bcd Providing Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand) etc. complete job as per building specifications and Extra for Brick work in superstructure in above plinth level upto floor V cum etc. complete job as per building specifications and direction of E/I. Rupees Five Thousand Seven Hundred Sixty Five And Paise Twenty Only

13 6.47A Bcd Providing 250 mm wide brick drain in cement mortar (1:6) with av. 150 mm Clear depth and 250 mm apron including cost of E/W involved with 75 mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base, the drain duly plastered in Cement Mortar

(1:3) with punning over exposed surface all complete as per building specification and direction of E/I, but excluding carriage cost of bricks, sand and jhama metal etc. all complete as per building specification and direction of E/I Rupees One Thousand Eighty Seven And Paise Ninety Only

14 6.1.12C + 6.3C Bcd Providing Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand) etc. complete job as per building specifications and Extra for Brick work in superstructure in above plinth level upto floor V cum etc. complete job as per building specifications and direction of E/I. Rupees Five Thousand Nine Hundred Fifty Eight And Paise Fifty Only

15 13.24.2 Bcd Providing 6 mm thick cement plaster to ceiling of mix 1:4 (1 cement : 4 coarse sand) finished with sand including cost of carriage screening curing with all leads and lifts of water scaffolding taxes and royalty etc. all complete as per building specifications and direction of Engineer-in-Charge. Rupees One Hundred Twenty Five And Paise Sixty Only

16 13.11.4 Bcd Providing 12 mm thick cement plaster mix 1:6 (1 cement : 6 coarse sand) with clean coarse sand of F.M. 1.5 with including cost of carriage, screening curing with all leads and lifts of water scaffolding taxes and royalty etc. all complete as per building specifications and direction of Engineer-in-Charge. Rupees One Hundred Forty One And Paise Fifty Only

17 13.12.1 + 13.36 Bcd Providing 15 mm cement plaster on rough side of single or half brick wall of mix (1:3) 1 cement 3 coarse sand etc. all complete as per building specifications and Extra for providing and mixing water proofing material in proportion recommended by the manufacturers : 15 mm cement plaster 1:3 (1 cement : 3 coarse sand) all complete as per building specifications and direction of Engineer-in-Charge. Rupees One Hundred Ninety Only

18 22.1.1 Bcd Providing and laying integral cement based treatment for water proofing on horizontal surfaces at all levels as directed by Engineer-in-charge and consisting of I) 1st layer of 20 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS : 12645 in proportions recommended by the

manufacturer II) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportions, III) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/ sqm thoroughly embedded in the 2nd layer etc. Using rough kota stone all complete as perspecifications and direction of Engineer-in-Charge. Rupees One Thousand Three Hundred Ninety Six And Paise Thirty Only

19 9.1.1 Bcd Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) : Second Class teakwood all complete as per building specifications and direction of E/I. Rupees One Lakh(s) Twenty Thousand Five Hundred Twenty Six Only

20 9.53. Bcd Providing 40 x 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x 10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) etc. all complete as per building specifications and direction of E/I. Rupees One Hundred Thirty And Paise Eighty Only

21 9.20.1 + 9.23 Bcd Providing and fixing ISI marked flush door shutters conforming to Is : 2202 (Part - I) decorative type, core of block board construction with frame of 1st class hard wood and well mathched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including stainless steel butt hinges with necessary screws. all complete as per specification and Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured) all complete as per building specifications and direction of E/I. Rupees Three Thousand Two Hundred Forty Seven Only

22 9.74.1 Bcd Providing and fixing bright finished brass tower bolts (barrel type) with necessary screw etc. complete : 250 x 10 mm all complete as per building specifications and direction of E/I. Rupees Three Hundred Sixty Nine And Paise Forty Only

23 9.74.3 Bcd Providing and fixing bright finished brass tower bolts (barrel type) with necessary screw etc. complete : 150 x 10 mm all complete as per building specifications and direction of E/I. Rupees Two Hundred Twenty Seven And Paise Thirty Only

24 9.75.1 Bcd Providing and fixing bright finished brass door latch with necessary screws etc. : 300 x 16 x 5 mm all complete as per building specifications and direction of E/I. Rupees Two Hundred Sixty Seven And Paise Twenty Only

25 9.81.1 Bcd Providing and fixing bright finished brass handles with screws etc. complete : 125 mm as per building specifications and direction of E/I. Rupees Two Hundred Two And Paise Ten Only

26 9.82. Bcd Providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc. complete as per building specifications and direction of E/I. Rupees One Hundred Eight And Paise Ten Only

27 9.48.1 Bcd Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete Fixed to steel windows by welding etc. as per building specifications and direction of E/I. Rupees One Hundred Forty Four And Paise Fifty Only

28 10.5.1 Bcd Providing and fixing 1 mm thick M.S. sheet door with frame of 40 x 40 x 6 mm angle iron, 3 mm M.S. gusset plates at the junction and corners all necessary fittings complete including applying a priming coat of approved steel primer : Using M.S. angle 40 x 40 x 6 mm for diagonal braces etc. all complete job as per building specifications and direction of Engineer-in-Charge. Rupees Three Thousand Six Hundred Fifty Three Only

29 10.18. Bcd Providing and fixing steel circular cast iron box for ceiling fan clamp 140 mm internal dia 73 mm height 5 mm thick rim bottom and top lids, 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one; pel at the comon clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing all complete as per standard design of building specifications and direction of Engineer-in-Charge. Rupees One Hundred Sixty Five And Paise Forty Only

30 10.36. Bcd Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes. channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners stainless steel bolts etc, of required size, on the top of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-in-eharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts.fasteners etc) all complete as per building specifications and direction of Engineer-in-Charge.. Rupees Five Hundred Forty Six And Paise Eighty Only

31 11.36. Bcd Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in

skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and joining with grey cement with pigment of matching shade complete all complete as per building specifications and direction of Engineer-in-Charge. Rupees Seven Hundred Ninety Five Only

32 11.40. Bcd Providing and laying Ceramic glazed floor tiles 400 x 400 mm (thickness to be specified by the manufacture) of 1st quality conforming to IS :13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colours such as white, lvory, Grey, Fume, Red, Brown, laid on 20 mm thick cement motar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. all complete as per building specifications and direction of Engineer-in-Charge. Rupees One Thousand Four Hundred Fourteen Only

33 11.41.2 Bcd Providing and laying vitrifed floor tiles in different sizes (thickness to be specified by the manufactrure) with water absorption's less than 0.08% and conforming to IS :15622 of approved make in all colours and shades, taid on 20 mm thick cement mortar 1:4 (1 cement 4 coarse sand) including grouting the joint with white cement and matching pigments etc. all complete Size of Tile 60 x 60 cm all complete as per building specifications and direction of Engineer-in-Charge. Rupees One Thousand Six Hundred Thirty Eight And Paise Eighty Only

34 8.9.1.2 Bcd Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/ sqm including pointing in white cement complete 8 mm thick : Granite of any colour and shade ect. all complete as per building specifications and direction of E/I. Rupees Two Thousand One Hundred Twelve And Paise Twenty Only

35 11.56.1 Bcd Providing and laying polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the builing all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of

matching shade including rubbing, curing and polishing etc. all complete as per building specifications and direction of Engineer-in-Charge : Polished Granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. Rupees Three Thousand Six Hundred Five And Paise Twenty Only

36 26.27.2 Bcd Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level uspended on

interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm,

spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) Rupees Two Thousand One Hundred Twenty And Paise Seventy Only

37 13.80A.2 Bcd Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per building specifications and direction of Engineer-in-Charge. Rupees One Hundred Five And Paise Forty Only

38 13.48.1 Bcd Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufactures : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr/10 sqm all complete as per building specifications and direction of Engineer-in-Charge. Rupees One Hundred Seventeen And Paise Thirty Only

39 13.78.2 + 13.92.1 Bcd Applying one coat of cement primer of approved brand and mandufacture on wall surface : Distemper primer etc. all complete as per building specifications and Providing Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work etc. all complete as per specification and direction of Engineer-in-Charge. Rupees One Hundred Twenty Five And Paise Ten Only

40 13.81.3 + 13.82.1 Bcd Applying priming coat With ready mixed zinc chromate yellow primer of approved brand and manufacture on steel galvanised iron/ steel works etc. all complete as per specification and Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade : New steel work (two or more coats) all complete as per specification and direction of Engineer-in-Charge.. Rupees One Hundred Eighteen And Paise Ten Only

41 13.101.1 Bcd Providing French spirit polishing : Tow or more coats on works including a coat of wood filler etc. all complete as per building specifications and direction of Engineer-in-Charge. Rupees Two Hundred Fifteen And Paise Eighty Only

42 21.18. Bcd Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). Rupees Five Thousand One Hundred Forty Three Only

43 21.16.3 Bcd Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer in-charge. Anodized Polyester powder coated minimum thickness 50 micron aluminium Rupees Eighty Nine And Paise Thirty Only

44 21.13. Bcd Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. lock with 6 level Rupees Three Hundred Sixty Five And Paise Twenty Only

45 11.79.1 Bcd Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength,thickness & size/shape, made by table vibratory method , to attain superior smooth finish using PU or equivalent moulds, laid in required Grey colour & pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through

vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per manufacturer’s specifications & direction of Engineer -in-Charge: (a) 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern. Rupees Nine Hundred Fifty Six And Paise Forty Only

46 17.7.1 +17.8 Bcd Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps etc. all complete as per specifications and Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings etc. all complete as per specification and direction of E/I. Rupees Four Thousand Two Hundred Sixty Four And Paise Forty Only

47 17.3.1 Bcd Providing and fixing white vitreous china pedestal type-water closet (European type) with seat & lid, 10 litre low level white vitrous china flushing cistern & C.P. flush bend with fittings & C.I. brakets, 40 mm flush bend over flow arrangement with specials of standard make and mosquito

proof coupling of aopproved municipal design complete including painting of fittings and brackets cutting and making good the wall and floors wherever require : WC pan with ISI marked white solid plastic seat and lid etc. all complete job as per specification and direction of E/I. Rupees Five Thousand Five Hundred Four And Paise Thirty Only

48 17.70.1 Bcd Providing and fixing PTMT Bottle Trap for Wash basin and sink Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 260gms etc. all complete job as per specification and direction of E/I. Rupees Three Hundred Twenty Five And Paise Ten Only

49 17.71. Bcd Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms etc. all complete job as per specification and direction of E/I. Rupees One Hundred Forty Six And Paise Thirty Only

50 17.73.2 Bcd Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. Rupees Four Hundred Twenty Four Only

51 17.72. Bcd Providing and fixing P.T.M.T. towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality, colour and make weighing not less than 88 gms etc. all complete job as per specification and direction of E/I. Rupees Two Hundred Four And Paise Seventy Only

52 18.22.2 Bcd Providing and fixing C.P. brass shower rose with 15 or 20 mm inlete : 150 mm diameter etc. all complete job as per specification and direction of E/I. Rupees One Hundred Ninety And Paise Ten Only

53 17.31.Bcd Providing and fixing 600 x 450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board griybd fuxed ti wiideb ckeats wutg C.P. brass screws and washers etc. all complete job as per specification and direction of E/I. Rupees One Thousand Sixty Eight And Paise Thirty Only

54 17.80. Bcd Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.. Rupees Six Thousand Five Hundred Thirty Four And Paise Twenty Only

55 18.48. Bcd Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank etc. all complete as per building specifications and direction of E/I. Rupees Nine And Paise Seventy Only

56 19.32.1 Bcd Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F./P.S. (non modular) bricks of class designation 75 etc. all complete as per specifications and direction of E/I. Rupees Thirty Three Thousand Six Hundred Three And Paise Forty Only

57 9.147D.2 Bcd Two track three panels sliding window with fly proof S.S. wire mesh (Two nos. glazed & one no. wire mesh panels) made 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 + 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) all complete as per approved drawing & direction of Engineer-in-Charge. Rupees Nine Thousand Four Hundred Seventy One Only

58 Carriage cost of materials -

(i) Local sand - 418.00 m³ 310.47 Rupees Three Hundred Ten And Paise Forty Seven Only 129776.00

(ii) Brick - 139865 % 0 Nos. 919.21 Rupees Nine Hundred Nineteen And Paise Twenty One Only 128565.00

(iii) Coarse Sand / Sone Sand - 405.35 m³ 1101.04 Rupees One Thousand One Hundred One And Paise Four Only 446307.00

(iv) Stone Chips - 386.87 m³ 1901.00 Rupees One Thousand Nine Hundred One Only 735440.00

59 Extra cost of materials -

(i) Brick - 139865 %0 Nos 268.32 Rupees Two Hundred Sixty Eight And Paise Thirty Two Only 37529.00

(ii) Cement - 44.170 MT 260.58 Rupees Two Hundred Sixty And Paise Fifty Eight Only 11510.00

Total Rs. 17801067.00

Add Extra GST @ 5.36% Rs. 954137.00

60 Add Seignorage Fee 10%

(i) Stone Aggregate - 386.87 m³ 62.500 Rupees Sixty Two And Paise Fifty Only 24179.00

(ii) Coarse Sand - 405.35 m³ 25.08 Rupees Twenty Five And Paise Eight Only 10166.00

(iii) Brick - 139865 % 0 Nos. 506.00 Rupees Five Hundred Six Only 70772.00

(iv) Local Sand - 418.00 m³ 14.19 Rupees Fourteen And Paise Nineteen Only 5931.00

(A) Total Rs. 18866252.00

61 1.1.3 Point wiring in PVC conduit, with piano type switch:- Wiring for light point, fan point, exhaust fan point, Call bell point with 1.5 sq. mm FR PVC insulated copper conductor single core cable in surfact/ recessed PVC conduit with piano type switch, phenolic laminatied sheet, suitable size PVC/ G.I. box etc. as required all complete as per specification and direction of E/I. Group - C Rupees One Thousand One Hundred Twenty Only

62 1.7.9 Circuit/ Submain wiring in PVC conduit:- Wiring for circuit/ submain wiring along with earth wire with the following sizes P.V.C. insulated copper conductor, single core cable in surface/ recessed P.V.C. conduit as required as per specification and direction of E/I. 4 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire Rupees Three Hundred Forty Eight Only

63 1.7.11 Circuit/ Submain wiring in PVC conduit:- Wiring for circuit/ submain wiring along with earth wire with the following sizes P.V.C. insulated copper conductor, single core cable in surface/ recessed P.V.C. conduit as required as per specification and direction of E/I. 4 x 6.0 sq.mm + 1 x 6.0 sq.mm earth wire Rupees Six Hundred Sixty Only

64 1.7.12 Circuit/ Submain wiring in PVC conduit:- Wiring for circuit/ submain wiring along with earth wire with the following sizes P.V.C. insulated copper conductor, single core cable in surface/ recessed P.V.C. conduit as required as per specification and direction of E/I. 4 x 10.0 sq.mm + 1 x 10.0 sq.mm earth wire Rupees Nine Hundred Twenty Five Only

65 1.7.3 Circuit/ Submain wiring in PVC conduit:- Wiring for circuit/ submain wiring along with earth wire with the following sizes P.V.C. insulated copper conductor, single core cable in surface/ recessed P.V.C. conduit as required as per specification and direction of E/I. 2 x 4.0 sq.mm + 1 x 4.0 sq.mm earth wire Rupees Three Hundred Nine Only

66 1.33. S/F Ceiling rose :- Supply and fitting 2 pin, 5 amp. Ceiling rose on the existing junction box / PVC box including connection etc. as required all complete as per specification and direction of E/I. Rupees Sixty Four Only

67 1.33. S/F Ceiling rose :- Supply and fitting 2 pin, 5 amp. Ceiling rose on the existing junction box / PVC box including connection etc. as required all complete as per specification and direction of E/I. Rupees Sixty Four Only

68 1.34. S/F Batten holder :- Supplying and fixing batten/ angle holder including connection etc. as required all complete as per specification and direction of E/I. Rupees Eighty Only

69 1.30. Supplying and fixing metal/ PVC box of 180 mm x 100 mm x 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in frnt including providing and fixing 6 pin, 5/6 and 15/16 amps socket outlet and 15/16 amps piano type switch, connections, painting etc. all required all complete as per specification and direction of E/I. Rupees Four Hundred Twenty Four Only

70 1.32. S/F power plug point with piano type accessories :- Supplying and fixing suitable size G.I./ PVC box on surface or in recess with pheonolic laminated sheet cover in front including providing and fixing 6 pin, 15/16 amps socket outlet and 15/16 amps piano type switch connection, painting etc. all required all complete as per specification and direction of E/I. Rupees Five Hundred Thirty One Only

71 1.25. S/F Modular type electronic fan regulator:- Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as requared as per specification and direction of E/I. Rupees Three Hundred Fifty Eight Only

72 10.18. Providing and fixing steel circular cast iron box for ceiling fan clamp 140 mm internal dia 73 mm height 5 mm thick rim bottom and top lids, 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one; pel at the comon clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing all complete as per standard design of building specifications and direction of Engineer-in-Charge. Rupees One Hundred Sixty Five And Paise Forty Only

73 2.10.2 S/F Vertical type TP MCB DB :- Supplying and fixing following way, surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amp tinned copoper bus bar, common neatral link, earth bar, din bar, for mounting MCB's (but without MCB's and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) all complete as per specification and direction of E/I.. 8 way (8 + 24), Double door, vertical type Rupees Ten Thousand Seven Hundred Seven Only

74 2.9.1 S/F TP MCB DB :- Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, phosphatized & power painted including earthing etc. as required (But without MCB/ RCCB/ Isolator) all complete as per specification and direction of E/I. 4 way (4 + 12), single doore, horizontal type Rupees Four Thousand One Hundred Eighty Four Only

75 2.12.7 S/F 'C' series, SP MCB :- Supplying and fixing following ratin, 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required all complete as per specification and direction of E/I. 40 A to 63 A, TP Rupees One Thousand Eight Hundred Fifty Nine Only

76 2.15.1 S/F DP MCB isolator:- Supplying and fixing following rating, double pole, 240 volts isolator in the existing MCB DB complete with connection testing and commissionig etc. as required as per specification and direction of E/I. 40 amps Rupees Four Hundred Twenty Nine Only

77 1602 32 amps. double pole switch disconnector fuse unit, rewireable type all complete as per specification and direction of E/I. Rupees One Thousand Two Hundred Fifty Two Only

78 2.5.5 S/F Busbar chamber :- Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty, complete with all accessories including connections earthing the body etc. as required all complete as per specification and direction of E/I. 400 amps Rupees Nineteen Thousand Forty Eight Only

79 2.5.3 S/F Busbar chamber :- Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty, complete with all accessories including connections earthing the body etc. as required all complete as per specification and direction of E/I. 200 amps Rupees Ten Thousand Five Hundred Fifty Only

80 2.4.5 S/F MCCB in cubicle panel board :- Providing and fixing following rating and capacity four pole MCCB in existing panel board, including drilling holes in cubical panel maleirg connection etc. as required all complete as per specification and direction of E/I. 250 amps, 36 KA Rupees Eighteen Thousand Six Hundred Forty Six Only

81 2.7.1 S/F ON-load/ panel mounted changeover:- Providing and fixing following capacity 4 pole ON load/ panel mounted change voer switches in existing cubicle panel board, making connection, earthing the body etc. as required all complete as per specification and direction of E/I. 40 amps, 4 pole Rupees Seven Thousand One Hundred Thirty Five Only

82 2.2.3 S/F Panel mounted TP & N in cubicle panel board :- Providing and fixing following capacity TP & N disconnector fuse switch unit inside the existing cubicle panel board, with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required all complete as per specification and direction of E/I. 200 amps TP & N Rupees Ten Thousand Two Hundred Forty Six Only

83 2.20. P/F M.V. danger notice plate:- Providing and fixing M.V. danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side etc., as required all complete as per specification and direction of E/I. Rupees Two Hundred Fourteen Only

84 8.11. Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compart-mentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.) as per specification and direction of E/I. Rupees One Thousand Eight Hundred Nine Only

85 2.1.1 S/F rewireable double pole/ TP & N switch disconnector:- Providing and fixing following capacity double pole/ TP & N sheet metal switch disconnector fuse unit in existing metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc. as required all complete as per specification and direction of E/I. 16 amps, double pole Rupees Nine Hundred Seventy Eight Only

86 2.1.2 S/F rewireable double pole/ TP & N switch disconnector:- Providing and fixing following capacity double pole/ TP & N sheet metal switch disconnector fuse unit in existing metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc. as required all complete as per specification and direction of E/I. 32 amps, double pole Rupees One Thousand Nine Hundred Forty Six Only

87 2211 Bcd Elect. Code S/L armoured cable:- Supplying and laying following sizes and core PVC / XLPE insulated PVC sheathed, heavy duty, armoured electrical cable withy aluminium conductor for working voltage upto and including 1100 volts. (conforms to IS: 1554, part-I) as per specification and direction of E/I. 150 sq.mm., 3.5 core Rupees Nine Hundred Sixty Five Only

88 2212 Bcd Elect. Code S/L armoured cable:- Supplying and laying following sizes and core PVC / XLPE insulated PVC sheathed, heavy duty, armoured electrical cable withy aluminium conductor for working voltage upto and including 1100 volts. (conforms to IS: 1554, part-I) as per specification and direction of E/I. 185 sq.mm., 3.5 core Rupees One Thousand Two Hundred Thirty Nine Only

89 3.1. G.I. earth pipe electrodde with salt/ charcoal :- Earthing with G.I. earth pipe 4.5 mtr long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt etc. as required all complete as per specification and direction of E/I. Rupees Five Thousand Thirty Three Only

90 3.3. G.I. earth plate electrode:- Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonary enclosure with over plate having locking arrangement and watering pipe etc. as required (But without charcoal or cole and salt) all complete as per specification and direction of E/I. Rupees Five Thousand Five Hundred Seventy Eight Only

91 3.10. P/F 25 mm x 5 mm copper strip in pipe:- Providing and fixing 25 mm x 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required all complete as per specification and direction of E/I. Rupees One Thousand Six Hundred Twenty Eight Only

92 2.17.1 S/F SPN RCCB :- Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required all complete as per specification and direction of E/I. 25 amps Rupees Two Thousand One Hundred Thirty One Only

93 3.19. P/F 4 mm copper loop earthing wire in surface/ recess:- Providing and fixtting 4.00 mm dia copper wire on surface or in recess for loop earthing as required all complete as per specification and direction of E/I. Rupees One Hundred Twenty Two Only

94 4.4. Jointing copper / G.I. tape (with another copper / GI tape, base of the finial or any other metallic object) by riverting/ nut bolting sweating and soldering etc. as required all complete as per specification and direction of E/I. Rupees Eighty One Only

95 1911 Basic code elect. Supplying G.I. pipe (32 mm dia) medium class G.I. Pipe for ranging lighting luminaire and ceilling fand etc. as required as per specification and direction of E/I. Rupees Three Hundred Thirty Four And Paise Eighty Only

96 1.44. ITC Ceiling fan:- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated copper conductor, single cable etc. as reqed. all complete as per specification and direction of E/I. Rupees One Hundred Thirty Five Only

97 1.50.1 ITC exhaust fan upto 450 mm sweep:- Installation of exhuast Fan upto 450 mm sweep in the existing opening including, including making the hole to suit the size of the above fan making good the damage connection, testing, commissioning etc. as required all complete as per specification and direction of E/I. Rupees Two Hundred Ninety Six Only

98 1.49. Fixing louvers shutters for exhaust fan:- Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required. etc. all complete as per specification and direction of E/I. Rupees Thirty Eight Only

99 8.17.1 Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required all complete as per specification and direction of E/I. 300 mm sweep Rupees Two Thousand Five Hundred Seventy Two Only

100 8.15. Supply and installation of regular/standard model A.C.ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required all complete as per specification and direction of E/I. Rupees Two Thousand Four Hundred Eighty Two Only

101 8.16. Supply and installation of regular/standard model A.C. ceiling fan of 1400 mm sweep with service value (CM/MM) minimum 4.10, Air delivery minimum 245 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required all complete as per specification and direction of E/I. Rupees Two Thousand Eight Hundred Thirty Eight Only

102 1.56. Supplying and fixing suitable size GI box with rnodular plate and cover in front on surface or in recess, including providing and fixing 3 nos. 5 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc.as required. etc. as required all complete as per specification and direction of E/I. Rupees Seven Hundred Seventy Eight Only

103 1.15.3 Wiring in existing conduit:- Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in existing surface/ recessed PVC conduit as required all complete as per specification and direction of E/I. 3 x 1.5 sq.mm Rupees Ninety Three Only

104 5.6.2 Supplying and fixing following types aluminium extruded suspended type LED luminaire with minimum efficacy 100 lm/w ensuring uniform and continuous illumination including suspension system complete with electronic driver etc and connection with 1.5 sq.mm FRLS pVC insulated copper conductor cable etc as required 4' Iong X 35/40 watt as per specification and direction of E/I. Rupees Four Thousand Five Hundred Eighty Seven Only

105 2007 35/40 watt X 4 ft aluminium extruded suspended type lighting system ensuring unifrom and continuous illumination including suspension system and electronic drriver etc. Minimum efficacy 100 lm/w etc as required all complete as per specification and direction of E/I. Rupees Three Thousand One Hundred Only

106 2024 50 watt LED FLOOD light with pressure die cast housing toughened glass, lP 65 protection and complete with electronic driver etc. Minimum efficacy 100 lm/w all complete as per specification and direction of E/I. Rupees Two Thousand Five Hundred Only

107 5.14.4 Supplying and fixing following Type LED street light with minimum efficacy 100 lm/w in die cast aluminium housing toughened glass, IP 66 protection and complete with electronic driver etc on pole / building including connection earthing the body etc as required all complete job as per specification and direction of E/I. 90 watt. Rupees Five Thousand Five Hundred Sixteen Only

B Total Rs. 2896600.00

108 Cost of Information Board Rupees Four Thousand Only

C Total Rs. 4000.00

Grand Total = (A + B + C) 21766852.00

Rupees Two Crore Seventeen Lakh(s) Sixty Six Thousand Eight Hundred Fifty Two Only

NOTE:- This estimate has been prapered on the basis of schedule of rate Govt. of Bihar wef 01.01.2022

RATE QUOTED BY THE TENDERER

1 …………………………. ON SCHEDULE RATE

2 …………………………. % ABOVE OF SCHEDULE RATE

3 …………………………. % BELOW OF SCHEDULE RATE

NOTE:- RATE QUOTED BY THE TENDERER EXCESS OR BELOW 10% OF SCHEDULE RATE WILL NOT BE ENTERTAINED.