REPAIRS TO PARKING AREA DRAINS HARD STANDING FENCING GATES COMPOUND WALL ETC AT BAIRAGARH AREA UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Dismantling of asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings, including ridge complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI Based corrugated steel sheeting 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, chajjas, fixed with self tapping screws complete all as specified and directed. (Make:- JSW-AZ-150, TATA, Everest, Metco)

S&F pre-painted galvalume aluminum zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. (Make:- JSW-AZ-150, TATA, Everest, Metco)

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.50 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard dense soil complete all as specified and directed.

M&L for cement concrete ( nomaial mix) using 40 mm graded aggregate type B2 1:2:4 in foundations, filling and mass concrete complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

S&F rolled mild steel work as in rafter, purlins, trusses and like (beam, tee, angle, channel or flat sections complete all as specified and directed.

M&L for mild steel angle, flat iron work as in post and struts in fencing including cutting tops to shape as directed drilling holes, notching for wire etc flat iron fillets (for scruing wire mesh etc) incl all necessary drilling bolting or riveting etc complete all as specified and directed.

S&F mild steel flat iron as in clamps, hold fasts wind ties etc complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 10cm but not exceeding 5 cm long and dia of shank 11 to 15mm complete all as specified and directed.

S&F galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm to 80mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and directed.

S&F chain link fencing including line wires, 50mm x 50mm, size and any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and directed. Note : Mesh size and dia of wire shall be as directed by Engr-in Charge.

M&L for preparation of new or previously untreated steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for framed work such as grills, gratings, gate including welding etc with ends of bars souldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railing, frame work of water tanks and similar work conforming to Fe-290, Gde E-165 complete all as specified and directed.

Demolition of brick work, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with fly ash bricks straight or curved on plan exc 6m mean radius, built in cm 1:6 complete all as specified and directed.

M&L for brick work with Sub Class B straight or curved on plan exc 6 m mean radius, built in cm 1:6 complete all as specified and directed.

Excavation in trenches not exc 1.5m wide & not exc 1.5m in depth: for foundation etc or for manholes, laying of pipe lines, cables, pipes etc Harde/dense soil and getting out complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, subbase, haunching for pipe etc complete all as specified and directed.

M&L for reinforced cement concrete M-20 (Nomial Mix ) using 20 mm aggregate as walls, drains, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

M&L for mild steel round plain bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Use and waste of formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter for fair finished flat surfaces of concrete complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Integral water profing compound mixed with cement mortar complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coat Acrylic emulsion exterior paint over 2mm coat of putty complete all as specified and directed.

M&L for cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in coping, benching etc for drain bed, edges of paver block and similar works complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2, concrete bed to drain pipes 200mm dia including packing under, and haunching against the sides of pipes after they are laid and tested; complete all as specified and directed.

S&F class SN 8 structured wall polyethylene piping system (pipe with online coupler and elastomeric rubber ring) with hollow annular profiled outer surface and a smooth inner surface (double wall corrugated) for non-pressure underground drainage and sewerage application, Type B, Nominal Size (DN/ID) 200 made of polyethylene (PE) material conforming to per ISI 6098 (Part 2) : 2013 and to be transported, handled, installed and joined as per Annex A of ISI 6098 (Part 2) : 2013 complete all as specified and directed.

M&L for removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick each layer as in soil complete all as specified and directed.

M&L for PVC (SWR) pipes, single socketed, in any length, with rubber rings 75mm dia as in weep holes complete all as specified and directed.

M&L for hardcore of Broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for factory made, machine pressed, M-35 grade concrete interlocking paver blocks (glossy/reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 60 mm thickness with complete all as specified and directed.

M&L for factory made, machine pressed, M-40 grade concrete interlocking paver blocks (glossy/reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 80 mm thickness complete all as specified and directed.

M&L for sand cushioning for laying of Interlocking paver block complete all as specified and directed.

M&L for heavy duty flooring tiles, harsh weather & UV Resistance, high abrasion resistance, MOH Hardness >6, thickness 10 mm thick, area of each tile not less than 0.09 sqm, anti slip type, laid in floors, steps, edges, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with & including 15mm thick rendering in CM 1:4 incl dismantling old tiles complete all as specified and directed.

Deduct Schedule of credit (calculation will be done off line) Rs. 67570.00

Jyoti enterprises

M/S Shanti Enterprises

R K Sales

ROYAL CONSTRUCTION

M/s VIKAS TRADERS

NDS TRADERS

M/s Kishan Construction Company

Samaksh Enterprises

PADAMSHRI CONSTRUCTION CO

M/S Shanti Traders

RAJPATI CONSTRUCTION

Nakoda Constrcution Company