Loading…
Loading…
Tender Value
₹18.7 L
EMD Value
₹37,450
Closing Date
24 Aug 2026, 5:00 pmDue today
Executive Engineer
Jal Shakti Division No-I Kasumpati Shimla-9(HP)
.
2026_HPIPH_141154_1
Kasumpti/shimla/LWSS Rajhana / Rs.18.70
Open Tender
Civil Works - Water Works
Item Rate
180 days
Kasumpti
Please refer Tender documents.
6 documents required · 6 mandatory
₹500
EE Jal Shakti Division No-I Kasumpati Shimla-9
₹37,450
14 Aug 2026
14 Aug 2026
25 Aug 2026
14 Aug 2026
24 Aug 2026
14 Aug 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | Excavation in drains and channels etc. in earth work for pipes upto all depth in all classification of earth work such as pick work, jumper work, saturated soil i/c balling or pumping out water , blasting soft /hard rock or chiseling soft/ hard rock where blasting is prohibited in all lifts including jungle clearance wherever required, trimming and dressing of sides, levelling of beds to correct grade including shoring /struting, planking, timbering and dewatering wherever required stacking the useable /unusable material/soil seperately and after laying,jointing and testing of pipes ,returning the useable soil in treches in 15 cm layers including consolidating of such deposited layer by ramming and watering and then disposing of all surplus excavated soil/ unusable material as directed within all leads and lifts including restoration of un-metalled surfaces to its original condition and including cost of diversion for traffic, night signals, fixing caution boards,crossing over trenches for access to houses, fencing etc. complete in all respect whithin all leads and lifts as per direction of the Engineer-in-charge. | 455.8 | Cum. | 100 | ₹45,580 |
| 2Providing and laying cement concrete work 1:1:2(1cement:1 and:2 graded stone agg. 20mm nominal size) and curing complete excluding cost of form work and reinforcement in reinforced concrete work i/c all leads and lifts complete in all respect. | |||||
| 2.01 | Foundation and plinth. | 1.88 | Cum. | 100 | ₹188 |
| 3 | 15mm cement plaster in single coat on fair side on brick/concrete/stone walls for interior plastering upto floor two level including arrises, internal rounding angles, chambers and or rounded angles not exceeding 80mm in girth and finished even and smooth:- Cement mortor 1:4 | 51.28 | Sqmt. | 100 | ₹5,128 |
| 4 | Prov. in RCC work smooth finishing of the exposed surfaces with cement mortar 1:3(1cement:3sand). | 51.28 | Sqmt. | 100 | ₹5,128 |
| 5 | Finishing wall with water proofing cement paint or approved brand and manufacture as and of required shade on undecorated wall surfaces two coats to give an even shade after thoroughly brushing the surface to remove dirt and dust of remaining work. | 51.28 | Sqmt. | 100 | ₹5,128 |
| 6Providing and laying with butt welding and testing of following dia Heavy Grade GI pipe including jointing the pipes with butt welding at both the end according to relevant BIS standards/approved specifications including manufacturing reducers/tapers, all short pieces and bends as per site requirement and made from parent tubes ( to be measiured and paid alongwith pipes, bends shall be manufactured in such a way that not more than 111/4 degree deflection is caused by a single cut and internal dia is not reduced including hydraulic testing to the entire satisfaction of the Engineer-in-charge. The damaged portion of galvanisation due welding shall be provided with anticorrosive treatment by providing two coats of bituminous paint over priming coat as per AWWA specification C-203-1978.(Earth work to be measured and paid for separately). | |||||
| 6.01 | 80 mm dia (Heavy) | 300 | Rmt. | 100 | ₹30,000 |
| 7Providing and laying with butt welding and testing of following dia Medium Grade GI pipe including jointing the pipes with butt welding at both the end according to relevant BIS standards/approved specifications including manufacturing reducers/tapers, all short pieces and bends as per site requirement and made from parent tubes ( to be measiured and paid alongwith pipes, bends shall be manufactured in such a way that not more than 111/4 degree deflection is caused by a single cut and internal dia is not reduced including hydraulic testing to the entire satisfaction of the Engineer-in-charge. The damaged portion of galvanisation due welding shall be provided with anticorrosive treatment by providing two coats of bituminous paint over priming coat as per AWWA specification C-203-1978.(Earth work to be measured and paid for separately). | |||||
| 7.01 | 80 mm dia (Medium) | 1,100 | Rmt. | 100 | ₹1,10,000 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Tendernotice_1.pdf
PDF • 0.25 MB
BOQ_209512.xls
BOQ • 0.29 MB
form8.pdf
Tender Documents • 0.91 MB
6.pdf
Tender Documents • 0.24 MB
Terms.pdf
Tender Documents • 0.22 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].